486, 586, Pentiums, and various instruction-set-compatible chips by
AMD, Cyrix, and others.
+config GENERIC_TIME
+ bool
+ default y
+
config SEMAPHORE_SLEEPERS
bool
default y
bool
default y
depends on NUMA && (X86_SUMMIT || X86_GENERICARCH)
+ select ACPI_NUMA
+
+config HAVE_ARCH_PARSE_SRAT
+ bool
+ default y
+ depends on ACPI_SRAT
config X86_SUMMIT_NUMA
bool
config SCHED_SMT
bool "SMT (Hyperthreading) scheduler support"
depends on SMP
- default off
help
SMT scheduler support improves the CPU scheduler's decision making
when dealing with Intel Pentium 4 chips with HyperThreading at a
Enabling this feature will cause a message to be printed when the P4
enters thermal throttling.
+config VM86
+ default y
+ bool "Enable VM86 support" if EMBEDDED
+ help
+ This option is required by programs like DOSEMU to run 16-bit legacy
+ code on X86 processors. It also may be needed by software like
+ XFree86 to initialize some video cards via BIOS. Disabling this
+ option saves about 6k.
+
config TOSHIBA
tristate "Toshiba Laptop support"
---help---
choice
depends on EXPERIMENTAL && !X86_PAE
- prompt "Memory split"
+ prompt "Memory split" if EMBEDDED
default VMSPLIT_3G
help
Select the desired split between kernel and user memory.
bool
depends on HIGHMEM64G
default y
+ select RESOURCES_64BIT
# Common NUMA Features
config NUMA
comment "NUMA (Summit) requires SMP, 64GB highmem support, ACPI"
depends on X86_SUMMIT && (!HIGHMEM64G || !ACPI)
+config NODES_SHIFT
+ int
+ default "4" if X86_NUMAQ
+ default "3"
+ depends on NEED_MULTIPLE_NODES
+
config HAVE_ARCH_BOOTMEM_NODE
bool
depends on NUMA
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
- but it is indepedent of the system firmware. And like a reboot
+ but it is independent of the system firmware. And like a reboot
you can start any kernel with it, not just Linux.
The name comes from the similiarity to the exec system call.
config HOTPLUG_CPU
bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
- depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER && !X86_PC
+ depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER
---help---
- Say Y here to experiment with turning CPUs off and on. CPUs
- can be controlled through /sys/devices/system/cpu.
+ Say Y here to experiment with turning CPUs off and on, and to
+ enable suspend on SMP systems. CPUs can be controlled through
+ /sys/devices/system/cpu.
- Say N.
endmenu
tristate "NatSemi SCx200 support"
depends on !X86_VOYAGER
help
- This provides basic support for the National Semiconductor SCx200
- processor. Right now this is just a driver for the GPIO pins.
+ This provides basic support for National Semiconductor's
+ (now AMD's) Geode processors. The driver probes for the
+ PCI-IDs of several on-chip devices, so its a good dependency
+ for other scx200_* drivers.
- If you don't know what to do here, say N.
+ If compiled as a module, the driver is named scx200.
+
+config SCx200HR_TIMER
+ tristate "NatSemi SCx200 27MHz High-Resolution Timer Support"
+ depends on SCx200 && GENERIC_TIME
+ default y
+ help
+ This driver provides a clocksource built upon the on-chip
+ 27MHz high-resolution timer. Its also a workaround for
+ NSC Geode SC-1100's buggy TSC, which loses time when the
+ processor goes idle (as is done by the scheduler). The
+ other workaround is idle=poll boot option.
- This support is also available as a module. If compiled as a
- module, it will be called scx200.
+config K8_NB
+ def_bool y
+ depends on AGP_AMD64
source "drivers/pcmcia/Kconfig"