Blackfin: isram: clean up ITEST_COMMAND macro and improve the selftests

[safe/jmp/linux-2.6] / arch / cris / Kconfig

diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
index e6d440a..e25bf44 100644 (file)
--- a/arch/cris/Kconfig
+++ b/arch/cris/Kconfig
@@ -20,6 +20,15 @@ config RWSEM_GENERIC_SPINLOCK
 config RWSEM_XCHGADD_ALGORITHM
        bool
 
+config GENERIC_TIME
+       def_bool y
+
+config GENERIC_CMOS_UPDATE
+       def_bool y
+
+config ARCH_USES_GETTIMEOFFSET
+       def_bool y
+
 config GENERIC_IOMAP
        bool
        default y
@@ -54,9 +63,16 @@ config FORCE_MAX_ZONEORDER
 config CRIS
        bool
        default y
+       select HAVE_IDE
+
+config HZ
+       int
+       default 100
 
 source "init/Kconfig"
 
+source "kernel/Kconfig.freezer"
+
 menu "General setup"
 
 source "fs/Kconfig.binfmt"
@@ -259,6 +275,21 @@ menu "Drivers for built-in interfaces"
 source arch/cris/arch-v10/drivers/Kconfig
 source arch/cris/arch-v32/drivers/Kconfig
 
+config ETRAX_AXISFLASHMAP
+       bool "Axis flash-map support"
+       select MTD
+       select MTD_CFI
+       select MTD_CFI_AMDSTD
+       select MTD_JEDECPROBE if ETRAX_ARCH_V32
+       select MTD_CHAR
+       select MTD_BLOCK
+       select MTD_PARTITIONS
+       select MTD_CONCAT
+       select MTD_COMPLEX_MAPPINGS
+       help
+         This option enables MTD mapping of flash devices.  Needed to use
+         flash memories.  If unsure, say Y.
+
 config ETRAX_RTC
        bool "Real Time Clock support"
        depends on ETRAX_I2C
@@ -416,7 +447,7 @@ config ETRAX_SERIAL_PORT0_DMA1_IN
        help
          Enables the DMA1 input channel for ser0 (ttyS0).
          If you do not enable DMA, an interrupt for each character will be
-         used when receiveing data.
+         used when receiving data.
          Normally you want to use DMA, unless you use the DMA channel for
          something else.
 
@@ -543,7 +574,7 @@ config ETRAX_SERIAL_PORT2_DMA7_IN
        help
          Enables the DMA7 input channel for ser2 (ttyS2).
          If you do not enable DMA, an interrupt for each character will be
-         used when receiveing data.
+         used when receiving data.
          Normally you want to use DMA, unless you use the DMA channel for
          something else.
 
@@ -582,7 +613,7 @@ config ETRAX_SERIAL_PORT3_DMA3_IN
        help
          Enables the DMA3 input channel for ser3 (ttyS3).
          If you do not enable DMA, an interrupt for each character will be
-         used when receiveing data.
+         used when receiving data.
          Normally you want to use DMA, unless you use the DMA channel for
          something else.
 
@@ -657,6 +688,10 @@ source "fs/Kconfig"
 
 source "drivers/usb/Kconfig"
 
+source "drivers/uwb/Kconfig"
+
+source "drivers/staging/Kconfig"
+
 source "arch/cris/Kconfig.debug"
 
 source "security/Kconfig"