git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff
? search:
summary | shortlog | log | commit | commitdiff | tree
raw | inline | side by side
Blackfin: drop board resources for dead devices (pbx/ad9960)
[safe/jmp/linux-2.6] / arch / blackfin / mach-bf561 / boards / cm_bf561.c
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 3a79a90..cedcc3c 100644 (file)
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -33,12 +33,15 @@
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 #include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#endif
+#include <linux/ata_platform.h>
 #include <linux/irq.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
+#include <asm/dpmc.h>
 
 /*
  * Name the Board for the /proc/cpuinfo
@@ -51,16 +54,16 @@ const char bfin_board_name[] = "Bluetechnix CM BF561";
 #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
        {
-               .name = "bootloader",
+               .name = "bootloader(spi)",
                .size = 0x00020000,
                .offset = 0,
                .mask_flags = MTD_CAP_ROM
        }, {
-               .name = "kernel",
+               .name = "linux kernel(spi)",
                .size = 0xe0000,
                .offset = 0x20000
        }, {
-               .name = "file system",
+               .name = "file system(spi)",
                .size = 0x700000,
                .offset = 0x00100000,
        }
@@ -80,7 +83,7 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 /* SPI ADC chip */
 static struct bfin5xx_spi_chip spi_adc_chip_info = {
        .enable_dma = 1,         /* use dma transfer with this chip*/
@@ -95,16 +98,9 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
        .enable_dma = 0,
-       .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
-       .enable_dma = 1,
        .bits_per_word = 8,
 };
 #endif
@@ -123,7 +119,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
 
-#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
        {
                .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
                .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
@@ -143,23 +139,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad1836_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
-               .modalias = "ad9960-spi",
-               .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-               .bus_num = 0,
-               .chip_select = 1,
-               .controller_data = &ad9960_spi_chip_info,
-       },
-#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-       {
-               .modalias = "spi_mmc",
+               .modalias = "mmc_spi",
                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-               .chip_select = CONFIG_SPI_MMC_CS_CHAN,
-               .platform_data = NULL,
-               .controller_data = &spi_mmc_chip_info,
+               .chip_select = 5,
+               .controller_data = &mmc_spi_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
@@ -175,8 +161,13 @@ static struct resource bfin_spi0_resource[] = {
        [1] = {
                .start = CH_SPI,
                .end   = CH_SPI,
+               .flags = IORESOURCE_DMA,
+       },
+       [2] = {
+               .start = IRQ_SPI,
+               .end   = IRQ_SPI,
                .flags = IORESOURCE_IRQ,
-       }
+       },
 };
 
 /* SPI controller data */
@@ -206,6 +197,13 @@ static struct platform_device hitachi_fb_device = {
 
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+       .flags = SMC91X_USE_32BIT | SMC91X_NOWAIT,
+       .leda = RPC_LED_100_10,
+       .ledb = RPC_LED_TX_RX,
+};
 
 static struct resource smc91x_resources[] = {
        {
@@ -224,9 +222,25 @@ static struct platform_device smc91x_device = {
        .id = 0,
        .num_resources = ARRAY_SIZE(smc91x_resources),
        .resource = smc91x_resources,
+       .dev    = {
+               .platform_data  = &smc91x_info,
+       },
 };
 #endif
 
+static struct resource bfin_gpios_resources = {
+       .start = 0,
+       .end   = MAX_BLACKFIN_GPIOS - 1,
+       .flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+       .name = "simple-gpio",
+       .id = -1,
+       .num_resources = 1,
+       .resource = &bfin_gpios_resources,
+};
+
 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 static struct resource isp1362_hcd_resources[] = {
        {
@@ -283,8 +297,37 @@ static struct platform_device bfin_uart_device = {
 };
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+       {
+               .start = 0xFFC00400,
+               .end = 0xFFC004FF,
+               .flags = IORESOURCE_MEM,
+       },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX+1,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+static struct platform_device bfin_sir0_device = {
+       .name = "bfin_sir",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_sir0_resources),
+       .resource = bfin_sir0_resources,
+};
+#endif
+#endif
+
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
-#define PATA_INT       119
+#define PATA_INT       IRQ_PF46
 
 static struct pata_platform_info bfin_pata_platform_data = {
        .ioport_shift = 2,
@@ -320,8 +363,37 @@ static struct platform_device bfin_pata_device = {
 };
 #endif
 
+static const unsigned int cclk_vlev_datasheet[] =
+{
+       VRPAIR(VLEV_085, 250000000),
+       VRPAIR(VLEV_090, 300000000),
+       VRPAIR(VLEV_095, 313000000),
+       VRPAIR(VLEV_100, 350000000),
+       VRPAIR(VLEV_105, 400000000),
+       VRPAIR(VLEV_110, 444000000),
+       VRPAIR(VLEV_115, 450000000),
+       VRPAIR(VLEV_120, 475000000),
+       VRPAIR(VLEV_125, 500000000),
+       VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+       .tuple_tab = cclk_vlev_datasheet,
+       .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+       .vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+       .name = "bfin dpmc",
+       .dev = {
+               .platform_data = &bfin_dmpc_vreg_data,
+       },
+};
+
 static struct platform_device *cm_bf561_devices[] __initdata = {
 
+       &bfin_dpmc,
+
 #if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
        &hitachi_fb_device,
 #endif
@@ -330,6 +402,12 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
        &bfin_uart_device,
 #endif
 
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+       &bfin_sir0_device,
+#endif
+#endif
+
 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
        &isp1362_hcd_device,
 #endif
@@ -345,11 +423,13 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
        &bfin_pata_device,
 #endif
+
+       &bfin_gpios_device,
 };
 
 static int __init cm_bf561_init(void)
 {
-       printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+       printk(KERN_INFO "%s(): registering device resources\n", __func__);
        platform_add_devices(cm_bf561_devices, ARRAY_SIZE(cm_bf561_devices));
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
        spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
Full containers within linux kernel