#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/irq.h>
+#include <linux/i2c.h>
#include <linux/interrupt.h>
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
#include <linux/usb/musb.h>
-#endif
#include <asm/bfin5xx_spi.h>
#include <asm/cplb.h>
#include <asm/dma.h>
#include <asm/gpio.h>
#include <asm/nand.h>
+#include <asm/dpmc.h>
#include <asm/portmux.h>
-#include <asm/mach/bf54x_keys.h>
+#include <mach/bf54x_keys.h>
#include <linux/input.h>
#include <linux/spi/ad7877.h>
* Driver needs to know address, irq and flag pin.
*/
+#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+static struct resource bfin_isp1761_resources[] = {
+ [0] = {
+ .name = "isp1761-regs",
+ .start = 0x2C0C0000,
+ .end = 0x2C0C0000 + 0xfffff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_PG7,
+ .end = IRQ_PG7,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_isp1761_device = {
+ .name = "isp1761",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_isp1761_resources),
+ .resource = bfin_isp1761_resources,
+};
+
+static struct platform_device *bfin_isp1761_devices[] = {
+ &bfin_isp1761_device,
+};
+
+int __init bfin_isp1761_init(void)
+{
+ unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices);
+
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
+ set_irq_type(bfin_isp1761_resources[1].start, IRQF_TRIGGER_FALLING);
+
+ return platform_add_devices(bfin_isp1761_devices, num_devices);
+}
+
+void __exit bfin_isp1761_exit(void)
+{
+ platform_device_unregister(&bfin_isp1761_device);
+}
+arch_initcall(bfin_isp1761_init);
+#endif
+
#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
-#include <asm/mach/bf54x-lq043.h>
+#include <mach/bf54x-lq043.h>
static struct bfin_bf54xfb_mach_info bf54x_lq043_data = {
.width = 480,
{
.start = 0xFFC03100,
.end = 0xFFC031FF,
+ .flags = IORESOURCE_MEM,
},
#endif
};
};
#endif
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+#ifdef CONFIG_BFIN_SIR1
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+#ifdef CONFIG_BFIN_SIR2
+ {
+ .start = 0xFFC02100,
+ .end = 0xFFC021FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+#ifdef CONFIG_BFIN_SIR3
+ {
+ .start = 0xFFC03100,
+ .end = 0xFFC031FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir_resources),
+ .resource = bfin_sir_resources,
+};
+#endif
+
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
static struct resource smsc911x_resources[] = {
{
},
};
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 0,
+ .dyn_fifo = 0,
+ .soft_con = 1,
+ .dma = 1,
+ .num_eps = 7,
+ .dma_channels = 7,
+ .gpio_vrsel = GPIO_PE7,
+};
+
static struct musb_hdrc_platform_data musb_plat = {
#if defined(CONFIG_USB_MUSB_OTG)
.mode = MUSB_OTG,
#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
.mode = MUSB_PERIPHERAL,
#endif
- .multipoint = 0,
+ .config = &musb_config,
};
static u64 musb_dmamask = ~(u32)0;
#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
static struct mtd_partition partition_info[] = {
{
- .name = "Linux Kernel",
+ .name = "linux kernel(nand)",
.offset = 0,
.size = 4 * SIZE_1M,
},
{
- .name = "File System",
+ .name = "file system(nand)",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
},
};
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN)
+#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
static struct platform_device bf54x_sdh_device = {
.name = "bfin-sdh",
.id = 0,
};
#endif
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct mtd_partition ezkit_partitions[] = {
{
- .name = "Bootloader",
+ .name = "bootloader(nor)",
.size = 0x40000,
.offset = 0,
}, {
- .name = "Kernel",
- .size = 0xE0000,
+ .name = "linux kernel(nor)",
+ .size = 0x1C0000,
.offset = MTDPART_OFS_APPEND,
}, {
- .name = "RootFS",
+ .name = "file system(nor)",
.size = MTDPART_SIZ_FULL,
.offset = MTDPART_OFS_APPEND,
}
.num_resources = 1,
.resource = &ezkit_flash_resource,
};
+#endif
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-/* all SPI peripherals info goes here */
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
/* SPI flash chip (m25p16) */
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
- .name = "bootloader",
+ .name = "bootloader(spi)",
.size = 0x00040000,
.offset = 0,
.mask_flags = MTD_CAP_ROM
}, {
- .name = "linux kernel",
+ .name = "linux kernel(spi)",
.size = MTDPART_SIZ_FULL,
.offset = MTDPART_OFS_APPEND,
}
};
#endif
+#if defined(CONFIG_SND_BLACKFIN_AD1836) \
+ || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.cs_change_per_word = 0,
};
#endif
-static struct spi_board_info bf54x_spi_board_info[] __initdata = {
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
{
.mode = SPI_MODE_3,
},
#endif
+#if defined(CONFIG_SND_BLACKFIN_AD1836) \
+ || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+ {
+ .modalias = "ad1836-spi",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
- .irq = IRQ_PJ11,
+ .irq = IRQ_PJ11, /* newer boards (Rev 1.4+) use IRQ_PB4 */
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
#endif
};
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
#endif
#endif
+#ifdef CONFIG_I2C_BOARDINFO
+static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
+};
+
+#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
+static struct i2c_board_info __initdata bfin_i2c_board_info1[] = {
+#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE)
+ {
+ I2C_BOARD_INFO("pcf8574_lcd", 0x22),
+ },
+#endif
+#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+ {
+ I2C_BOARD_INFO("pcf8574_keypad", 0x27),
+ .irq = 212,
+ },
+#endif
+};
+#endif
+#endif
+
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
#include <linux/gpio_keys.h>
};
#endif
+static struct resource bfin_gpios_resources = {
+ .start = 0,
+ .end = MAX_BLACKFIN_GPIOS - 1,
+ .flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+ .name = "simple-gpio",
+ .id = -1,
+ .num_resources = 1,
+ .resource = &bfin_gpios_resources,
+};
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+/*
+ * Internal VLEV BF54XSBBC1533
+ ****temporarily using these values until data sheet is updated
+ */
+ VRPAIR(VLEV_085, 150000000),
+ VRPAIR(VLEV_090, 250000000),
+ VRPAIR(VLEV_110, 276000000),
+ VRPAIR(VLEV_115, 301000000),
+ VRPAIR(VLEV_120, 525000000),
+ VRPAIR(VLEV_125, 550000000),
+ VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+ .tuple_tab = cclk_vlev_datasheet,
+ .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+ .vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+ .name = "bfin dpmc",
+ .dev = {
+ .platform_data = &bfin_dmpc_vreg_data,
+ },
+};
+
static struct platform_device *ezkit_devices[] __initdata = {
+
+ &bfin_dpmc,
+
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
&rtc_device,
#endif
&bfin_uart_device,
#endif
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+ &bfin_sir_device,
+#endif
+
#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
&bf54x_lq043_device,
#endif
&bf5xx_nand_device,
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN)
+#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
&bf54x_sdh_device,
#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
&bfin_device_gpiokeys,
#endif
+
+ &bfin_gpios_device,
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
&ezkit_flash_device,
+#endif
};
static int __init ezkit_init(void)
{
- printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
- platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- spi_register_board_info(bf54x_spi_board_info,
- ARRAY_SIZE(bf54x_spi_board_info));
+#ifdef CONFIG_I2C_BOARDINFO
+ i2c_register_board_info(0, bfin_i2c_board_info0,
+ ARRAY_SIZE(bfin_i2c_board_info0));
+#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
+ i2c_register_board_info(1, bfin_i2c_board_info1,
+ ARRAY_SIZE(bfin_i2c_board_info1));
+#endif
#endif
+ platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
+
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+
return 0;
}