/*
- * File: arch/blackfin/mach-bf537/boards/stamp.c
- * Based on: arch/blackfin/mach-bf533/boards/ezkit.c
- * Author: Aidan Williams <aidan@nicta.com.au>
+ * Copyright 2004-2009 Analog Devices Inc.
+ * 2005 National ICT Australia (NICTA)
+ * Aidan Williams <aidan@nicta.com.au>
*
- * Created:
- * Description:
- *
- * Modified:
- * Copyright 2005 National ICT Australia (NICTA)
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * Licensed under the GPL-2 or later.
*/
#include <linux/device.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
+#include <linux/io.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
static struct isp1760_platform_data isp1760_priv = {
.is_isp1761 = 0,
- .port1_disable = 0,
.bus_width_16 = 1,
.port1_otg = 0,
.analog_oc = 0,
};
static struct platform_device bfin_isp1760_device = {
- .name = "isp1760-hcd",
+ .name = "isp1760",
.id = 0,
.dev = {
.platform_data = &isp1760_priv,
};
#endif
-static struct resource bfin_gpios_resources = {
- .start = 0,
- .end = MAX_BLACKFIN_GPIOS - 1,
- .flags = IORESOURCE_IRQ,
-};
-
-static struct platform_device bfin_gpios_device = {
- .name = "simple-gpio",
- .id = -1,
- .num_resources = 1,
- .resource = &bfin_gpios_resources,
-};
-
#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
static struct resource bfin_pcmcia_cf_resources[] = {
{
#endif
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource smc91x_resources[] = {
{
.name = "smc91x-regs",
.id = 0,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
};
#endif
static struct resource dm9000_resources[] = {
[0] = {
.start = 0x203FB800,
- .end = 0x203FB800 + 8,
+ .end = 0x203FB800 + 1,
.flags = IORESOURCE_MEM,
},
[1] = {
+ .start = 0x203FB804,
+ .end = 0x203FB804 + 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
.start = IRQ_PF9,
.end = IRQ_PF9,
.flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
.end = 0x20360004,
.flags = IORESOURCE_MEM,
}, {
- .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
+ .start = IRQ_PF3,
+ .end = IRQ_PF3,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
#endif
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+ .name = "bfin_mii_bus",
+};
+
static struct platform_device bfin_mac_device = {
.name = "bfin_mac",
+ .dev.platform_data = &bfin_mii_bus,
};
#endif
};
#endif
-#if defined(CONFIG_SPI_ADC_BF533) \
- || defined(CONFIG_SPI_ADC_BF533_MODULE)
+#if defined(CONFIG_BFIN_SPI_ADC) \
+ || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
- || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
+#if defined(CONFIG_SND_BF5XX_SOC_AD1938) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
+static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+ .cs_gpio = GPIO_PF5,
+};
+#endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
+#include <linux/input.h>
+#include <linux/input/ad714x.h>
+static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
+
+static struct ad714x_slider_plat slider_plat[] = {
+ {
+ .start_stage = 0,
+ .end_stage = 7,
+ .max_coord = 128,
+ },
+};
+
+static struct ad714x_button_plat button_plat[] = {
+ {
+ .keycode = BTN_FORWARD,
+ .l_mask = 0,
+ .h_mask = 0x600,
+ },
+ {
+ .keycode = BTN_LEFT,
+ .l_mask = 0,
+ .h_mask = 0x500,
+ },
+ {
+ .keycode = BTN_MIDDLE,
+ .l_mask = 0,
+ .h_mask = 0x800,
+ },
+ {
+ .keycode = BTN_RIGHT,
+ .l_mask = 0x100,
+ .h_mask = 0x400,
+ },
+ {
+ .keycode = BTN_BACK,
+ .l_mask = 0x200,
+ .h_mask = 0x400,
+ },
+};
+static struct ad714x_platform_data ad7147_platfrom_data = {
+ .slider_num = 1,
+ .button_num = 5,
+ .slider = slider_plat,
+ .button = button_plat,
+ .stage_cfg_reg = {
+ {0xFBFF, 0x1FFF, 0, 0x2626, 1600, 1600, 1600, 1600},
+ {0xEFFF, 0x1FFF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FFE, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FFB, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FEF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FBF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1EFF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1BFF, 0, 0x2626, 1600, 1600, 1600, 1600},
+ {0xFF7B, 0x3FFF, 0x506, 0x2626, 1100, 1100, 1150, 1150},
+ {0xFDFE, 0x3FFF, 0x606, 0x2626, 1100, 1100, 1150, 1150},
+ {0xFEBA, 0x1FFF, 0x1400, 0x2626, 1200, 1200, 1300, 1300},
+ {0xFFEF, 0x1FFF, 0x0, 0x2626, 1100, 1100, 1150, 1150},
+ },
+ .sys_cfg_reg = {0x2B2, 0x0, 0x3233, 0x819, 0x832, 0xCFF, 0xCFF, 0x0},
+};
+#endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7142EB)
+#include <linux/input.h>
+#include <linux/input/ad714x.h>
+static struct ad714x_button_plat button_plat[] = {
+ {
+ .keycode = BTN_1,
+ .l_mask = 0,
+ .h_mask = 0x1,
+ },
+ {
+ .keycode = BTN_2,
+ .l_mask = 0,
+ .h_mask = 0x2,
+ },
+ {
+ .keycode = BTN_3,
+ .l_mask = 0,
+ .h_mask = 0x4,
+ },
+ {
+ .keycode = BTN_4,
+ .l_mask = 0x0,
+ .h_mask = 0x8,
+ },
+};
+static struct ad714x_platform_data ad7142_platfrom_data = {
+ .button_num = 4,
+ .button = button_plat,
+ .stage_cfg_reg = {
+ /* fixme: figure out right setting for all comoponent according
+ * to hardware feature of EVAL-AD7142EB board */
+ {0xE7FF, 0x3FFF, 0x0005, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFDBF, 0x3FFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFFFF, 0x2DFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFFFF, 0x37BF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ },
+ .sys_cfg_reg = {0x0B2, 0x0, 0x690, 0x664, 0x290F, 0xF, 0xF, 0x0},
+};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
+ .pio_interrupt = 0,
};
#endif
};
#endif
+#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#include <linux/input.h>
+#include <linux/input/adxl34x.h>
+static const struct adxl34x_platform_data adxl34x_info = {
+ .x_axis_offset = 0,
+ .y_axis_offset = 0,
+ .z_axis_offset = 0,
+ .tap_threshold = 0x31,
+ .tap_duration = 0x10,
+ .tap_latency = 0x60,
+ .tap_window = 0xF0,
+ .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
+ .act_axis_control = 0xFF,
+ .activity_threshold = 5,
+ .inactivity_threshold = 3,
+ .inactivity_time = 4,
+ .free_fall_threshold = 0x7,
+ .free_fall_time = 0x20,
+ .data_rate = 0x8,
+ .data_range = ADXL_FULL_RES,
+
+ .ev_type = EV_ABS,
+ .ev_code_x = ABS_X, /* EV_REL */
+ .ev_code_y = ABS_Y, /* EV_REL */
+ .ev_code_z = ABS_Z, /* EV_REL */
+
+ .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
+
+/* .ev_code_ff = KEY_F,*/ /* EV_KEY */
+/* .ev_code_act_inactivity = KEY_A,*/ /* EV_KEY */
+ .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
+ .fifo_mode = ADXL_FIFO_STREAM,
+};
+#endif
+
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
.enable_dma = 0,
};
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SPI_ADC_BF533) \
- || defined(CONFIG_SPI_ADC_BF533_MODULE)
+#if defined(CONFIG_BFIN_SPI_ADC) \
+ || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
- || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
{
- .modalias = "ad1836-spi",
+ .modalias = "ad1836",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
.controller_data = &ad1836_spi_chip_info,
+ .mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
+
+#if defined(CONFIG_SND_BF5XX_SOC_AD1938) || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
{
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
+ .modalias = "ad1938",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
+ .chip_select = 0,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
+ .controller_data = &ad1938_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
+ {
+ .modalias = "ad714x_captouch",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .irq = IRQ_PF4,
+ .bus_num = 0,
+ .chip_select = 5,
+ .mode = SPI_MODE_3,
+ .platform_data = &ad7147_platfrom_data,
+ .controller_data = &ad7147_spi_chip_info,
},
#endif
+
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
.mode = SPI_MODE_0,
},
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+ {
+ .modalias = "adxl34x",
+ .platform_data = &adxl34x_info,
+ .irq = IRQ_PF6,
+ .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2,
+ .controller_data = &spi_adxl34x_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
};
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
[1] = {
.start = CH_SPI,
.end = CH_SPI,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
.flags = IORESOURCE_IRQ,
},
};
};
#endif /* spi master and devices */
+#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+
+/* SPORT SPI controller data */
+static struct bfin5xx_spi_master bfin_sport_spi0_info = {
+ .num_chipselect = 1, /* master only supports one device */
+ .enable_dma = 0, /* master don't support DMA */
+ .pin_req = {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_DRPRI,
+ P_SPORT0_RSCLK, P_SPORT0_TFS, P_SPORT0_RFS, 0},
+};
+
+static struct resource bfin_sport_spi0_resource[] = {
+ [0] = {
+ .start = SPORT0_TCR1,
+ .end = SPORT0_TCR1 + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_SPORT0_ERROR,
+ .end = IRQ_SPORT0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_sport_spi0_device = {
+ .name = "bfin-sport-spi",
+ .id = 1, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_sport_spi0_resource),
+ .resource = bfin_sport_spi0_resource,
+ .dev = {
+ .platform_data = &bfin_sport_spi0_info, /* Passed to driver */
+ },
+};
+
+static struct bfin5xx_spi_master bfin_sport_spi1_info = {
+ .num_chipselect = 1, /* master only supports one device */
+ .enable_dma = 0, /* master don't support DMA */
+ .pin_req = {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_DRPRI,
+ P_SPORT1_RSCLK, P_SPORT1_TFS, P_SPORT1_RFS, 0},
+};
+
+static struct resource bfin_sport_spi1_resource[] = {
+ [0] = {
+ .start = SPORT1_TCR1,
+ .end = SPORT1_TCR1 + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_SPORT1_ERROR,
+ .end = IRQ_SPORT1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_sport_spi1_device = {
+ .name = "bfin-sport-spi",
+ .id = 2, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_sport_spi1_resource),
+ .resource = bfin_sport_spi1_resource,
+ .dev = {
+ .platform_data = &bfin_sport_spi1_info, /* Passed to driver */
+ },
+};
+
+#endif /* sport spi master and devices */
+
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
static struct platform_device bfin_fb_device = {
.name = "bf537-lq035",
};
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
-static struct platform_device bfin_fb_adv7393_device = {
- .name = "bfin-adv7393",
-};
-#endif
-
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
#include <asm/bfin-lq035q1.h>
#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
#include <linux/input.h>
-#include <linux/i2c/adp5588_keys.h>
+#include <linux/i2c/adp5588.h>
static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
[0] = KEY_GRAVE,
[1] = KEY_1,
};
#endif
+#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#include <linux/mfd/adp5520.h>
+
+ /*
+ * ADP5520/5501 Backlight Data
+ */
+
+static struct adp5520_backlight_platfrom_data adp5520_backlight_data = {
+ .fade_in = FADE_T_1200ms,
+ .fade_out = FADE_T_1200ms,
+ .fade_led_law = BL_LAW_LINEAR,
+ .en_ambl_sens = 1,
+ .abml_filt = BL_AMBL_FILT_640ms,
+ .l1_daylight_max = BL_CUR_mA(15),
+ .l1_daylight_dim = BL_CUR_mA(0),
+ .l2_office_max = BL_CUR_mA(7),
+ .l2_office_dim = BL_CUR_mA(0),
+ .l3_dark_max = BL_CUR_mA(3),
+ .l3_dark_dim = BL_CUR_mA(0),
+ .l2_trip = L2_COMP_CURR_uA(700),
+ .l2_hyst = L2_COMP_CURR_uA(50),
+ .l3_trip = L3_COMP_CURR_uA(80),
+ .l3_hyst = L3_COMP_CURR_uA(20),
+};
+
+ /*
+ * ADP5520/5501 LEDs Data
+ */
+
+#include <linux/leds.h>
+
+static struct led_info adp5520_leds[] = {
+ {
+ .name = "adp5520-led1",
+ .default_trigger = "none",
+ .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | LED_OFFT_600ms,
+ },
+#ifdef ADP5520_EN_ALL_LEDS
+ {
+ .name = "adp5520-led2",
+ .default_trigger = "none",
+ .flags = FLAG_ID_ADP5520_LED2_ADP5501_LED1,
+ },
+ {
+ .name = "adp5520-led3",
+ .default_trigger = "none",
+ .flags = FLAG_ID_ADP5520_LED3_ADP5501_LED2,
+ },
+#endif
+};
+
+static struct adp5520_leds_platfrom_data adp5520_leds_data = {
+ .num_leds = ARRAY_SIZE(adp5520_leds),
+ .leds = adp5520_leds,
+ .fade_in = FADE_T_600ms,
+ .fade_out = FADE_T_600ms,
+ .led_on_time = LED_ONT_600ms,
+};
+
+ /*
+ * ADP5520 GPIO Data
+ */
+
+static struct adp5520_gpio_platfrom_data adp5520_gpio_data = {
+ .gpio_start = 50,
+ .gpio_en_mask = GPIO_C1 | GPIO_C2 | GPIO_R2,
+ .gpio_pullup_mask = GPIO_C1 | GPIO_C2 | GPIO_R2,
+};
+
+ /*
+ * ADP5520 Keypad Data
+ */
+
+#include <linux/input.h>
+static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
+ [KEY(0, 0)] = KEY_GRAVE,
+ [KEY(0, 1)] = KEY_1,
+ [KEY(0, 2)] = KEY_2,
+ [KEY(0, 3)] = KEY_3,
+ [KEY(1, 0)] = KEY_4,
+ [KEY(1, 1)] = KEY_5,
+ [KEY(1, 2)] = KEY_6,
+ [KEY(1, 3)] = KEY_7,
+ [KEY(2, 0)] = KEY_8,
+ [KEY(2, 1)] = KEY_9,
+ [KEY(2, 2)] = KEY_0,
+ [KEY(2, 3)] = KEY_MINUS,
+ [KEY(3, 0)] = KEY_EQUAL,
+ [KEY(3, 1)] = KEY_BACKSLASH,
+ [KEY(3, 2)] = KEY_BACKSPACE,
+ [KEY(3, 3)] = KEY_ENTER,
+};
+
+static struct adp5520_keys_platfrom_data adp5520_keys_data = {
+ .rows_en_mask = ROW_R3 | ROW_R2 | ROW_R1 | ROW_R0,
+ .cols_en_mask = COL_C3 | COL_C2 | COL_C1 | COL_C0,
+ .keymap = adp5520_keymap,
+ .keymapsize = ARRAY_SIZE(adp5520_keymap),
+ .repeat = 0,
+};
+
+ /*
+ * ADP5520/5501 Multifuction Device Init Data
+ */
+
+static struct adp5520_subdev_info adp5520_subdevs[] = {
+ {
+ .name = "adp5520-backlight",
+ .id = ID_ADP5520,
+ .platform_data = &adp5520_backlight_data,
+ },
+ {
+ .name = "adp5520-led",
+ .id = ID_ADP5520,
+ .platform_data = &adp5520_leds_data,
+ },
+ {
+ .name = "adp5520-gpio",
+ .id = ID_ADP5520,
+ .platform_data = &adp5520_gpio_data,
+ },
+ {
+ .name = "adp5520-keys",
+ .id = ID_ADP5520,
+ .platform_data = &adp5520_keys_data,
+ },
+};
+
+static struct adp5520_platform_data adp5520_pdev_data = {
+ .num_subdevs = ARRAY_SIZE(adp5520_subdevs),
+ .subdevs = adp5520_subdevs,
+};
+
+#endif
+
+#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+#include <linux/i2c/adp5588.h>
+static struct adp5588_gpio_platfrom_data adp5588_gpio_data = {
+ .gpio_start = 50,
+ .pullup_dis_mask = 0,
+};
+#endif
+
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_JOYSTICK_AD7142) || defined(CONFIG_JOYSTICK_AD7142_MODULE)
+#if defined(CONFIG_INPUT_EVAL_AD7142EB)
{
- I2C_BOARD_INFO("ad7142_joystick", 0x2C),
- .irq = IRQ_PF5,
+ I2C_BOARD_INFO("ad7142_captouch", 0x2C),
+ .irq = IRQ_PG5,
+ .platform_data = (void *)&ad7142_platfrom_data,
},
#endif
-#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE)
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PG6,
.platform_data = (void *)&adp5588_kpad_data,
},
#endif
+#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+ {
+ I2C_BOARD_INFO("pmic-adp5520", 0x32),
+ .irq = IRQ_PG0,
+ .platform_data = (void *)&adp5520_pdev_data,
+ },
+#endif
+#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("adxl34x", 0x53),
+ .irq = IRQ_PG3,
+ .platform_data = (void *)&adxl34x_info,
+ },
+#endif
+#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+ {
+ I2C_BOARD_INFO("adp5588-gpio", 0x34),
+ .platform_data = (void *)&adp5588_gpio_data,
+ },
+#endif
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+ {
+ I2C_BOARD_INFO("bfin-adv7393", 0x2B),
+ },
+#endif
+#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+ {
+ I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2C),
+ },
+#endif
};
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
#endif
#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
-#define PATA_INT IRQ_PF5
+#define CF_IDE_NAND_CARD_USE_HDD_INTERFACE
+/* #define CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE */
+#ifdef CF_IDE_NAND_CARD_USE_HDD_INTERFACE
+#define PATA_INT IRQ_PF5
static struct pata_platform_info bfin_pata_platform_data = {
.ioport_shift = 1,
.irq_flags = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
.flags = IORESOURCE_IRQ,
},
};
+#elif defined(CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE)
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 0,
+};
+/* CompactFlash Storage Card Memory Mapped Adressing
+ * /REG = A11 = 1
+ */
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x20211800,
+ .end = 0x20211807,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2021180E, /* Device Ctl */
+ .end = 0x2021180E,
+ .flags = IORESOURCE_MEM,
+ },
+};
+#endif
static struct platform_device bfin_pata_device = {
.name = "pata_platform",
},
};
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+ .name = "bfin-tdm",
+ /* TODO: add platform data here */
+};
+#endif
+
static struct platform_device *stamp_devices[] __initdata = {
&bfin_dpmc,
#endif
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+ &bfin_mii_bus,
&bfin_mac_device,
#endif
&bfin_spi0_device,
#endif
+#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+ &bfin_sport_spi0_device,
+ &bfin_sport_spi1_device,
+#endif
+
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
&bfin_fb_device,
#endif
&bfin_lq035q1_device,
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
- &bfin_fb_adv7393_device,
-#endif
-
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
&bfin_device_gpiokeys,
#endif
- &bfin_gpios_device,
-
#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
&bfin_async_nand_device,
#endif
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
&stamp_flash_device,
#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+ &bfin_tdm,
+#endif
};
static int __init stamp_init(void)
platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
- irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
-#endif
-
return 0;
}