#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
#include <linux/i2c.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
-#include <linux/usb/sl811.h>
#include <linux/usb/musb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
/*
* Name the Board for the /proc/cpuinfo
*/
+#ifdef CONFIG_BFIN527_EZKIT_V2
+const char bfin_board_name[] = "ADI BF527-EZKIT V2";
+#else
const char bfin_board_name[] = "ADI BF527-EZKIT";
+#endif
/*
* Driver needs to know address, irq and flag pin.
};
static struct platform_device bfin_isp1760_device = {
- .name = "isp1760-hcd",
+ .name = "isp1760",
.id = 0,
.dev = {
.platform_data = &isp1760_priv,
};
#endif
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#include <asm/bfin-lq035q1.h>
+
+static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
+ .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
+ .ppi_mode = USE_RGB565_8_BIT_PPI,
+};
+
+static struct resource bfin_lq035q1_resources[] = {
+ {
+ .start = IRQ_PPI_ERROR,
+ .end = IRQ_PPI_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_lq035q1_device = {
+ .name = "bfin-lq035q1",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_lq035q1_resources),
+ .resource = bfin_lq035q1_resources,
+ .dev = {
+ .platform_data = &bfin_lq035q1_data,
+ },
+};
+#endif
+
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct mtd_partition ezkit_partitions[] = {
{
};
#endif
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-static struct resource sl811_hcd_resources[] = {
- {
- .start = 0x20340000,
- .end = 0x20340000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20340004,
- .end = 0x20340004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = CONFIG_USB_SL811_BFIN_IRQ,
- .end = CONFIG_USB_SL811_BFIN_IRQ,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-void sl811_port_power(struct device *dev, int is_on)
-{
- gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
- gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
-}
-#endif
-
-static struct sl811_platform_data sl811_priv = {
- .potpg = 10,
- .power = 250, /* == 500mA */
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
- .port_power = &sl811_port_power,
-#endif
-};
-
-static struct platform_device sl811_hcd_device = {
- .name = "sl811-hcd",
- .id = 0,
- .dev = {
- .platform_data = &sl811_priv,
- },
- .num_resources = ARRAY_SIZE(sl811_hcd_resources),
- .resource = sl811_hcd_resources,
-};
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
- {
- .start = 0x20360000,
- .end = 0x20360000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20360004,
- .end = 0x20360004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct isp1362_platform_data isp1362_priv = {
- .sel15Kres = 1,
- .clknotstop = 0,
- .oc_enable = 0,
- .int_act_high = 0,
- .int_edge_triggered = 0,
- .remote_wakeup_connected = 0,
- .no_power_switching = 1,
- .power_switching_mode = 0,
-};
-
-static struct platform_device isp1362_hcd_device = {
- .name = "isp1362-hcd",
- .id = 0,
- .dev = {
- .platform_data = &isp1362_priv,
- },
- .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
- .resource = isp1362_hcd_resources,
-};
-#endif
-
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
static struct platform_device bfin_mii_bus = {
.name = "bfin_mii_bus",
.median = 2, /* do 8 measurements */
.averaging = 1, /* take the average of 4 middle samples */
.pen_down_acc_interval = 255, /* 9.4 ms */
- .gpio_output = 1, /* configure AUX/VBAT/GPIO as GPIO output */
- .gpio_default = 1, /* During initialization set GPIO = HIGH */
+ .gpio_export = 0, /* Export GPIO to gpiolib */
};
#endif
};
#endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
- && defined(CONFIG_SND_SOC_WM8731_SPI)
-static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
};
#endif
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+ .name = "bfin-i2s",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+ .name = "bfin-tdm",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
- && defined(CONFIG_SND_SOC_WM8731_SPI)
- {
- .modalias = "wm8731",
- .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 5,
- .controller_data = &spi_wm8731_chip_info,
- .mode = SPI_MODE_0,
- },
-#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
{
.modalias = "spidev",
.controller_data = &spidev_chip_info,
},
#endif
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+ {
+ .modalias = "bfin-lq035q1-spi",
+ .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 7,
+ .controller_data = &lq035q1_spi_chip_info,
+ .mode = SPI_CPHA | SPI_CPOL,
+ },
+#endif
};
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
};
#endif /* spi master and devices */
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
-static struct platform_device bfin_fb_device = {
- .name = "bf537-lq035",
-};
-#endif
-
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
-static struct platform_device bfin_fb_adv7393_device = {
- .name = "bfin-adv7393",
-};
-#endif
-
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
{
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
+ .start = UART0_THR,
+ .end = UART0_GCTL+2,
.flags = IORESOURCE_MEM,
},
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART0_ERROR,
+ .end = IRQ_UART0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_TX,
+ .end = CH_UART0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+ P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+ .name = "bfin-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+ .resource = bfin_uart0_resources,
+ .dev = {
+ .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+ },
+};
#endif
#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
{
- .start = 0xFFC02000,
- .end = 0xFFC020FF,
+ .start = UART1_THR,
+ .end = UART1_GCTL+2,
.flags = IORESOURCE_MEM,
},
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART1_ERROR,
+ .end = IRQ_UART1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_TX,
+ .end = CH_UART1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+ { /* CTS pin */
+ .start = GPIO_PF9,
+ .end = GPIO_PF9,
+ .flags = IORESOURCE_IO,
+ },
+ { /* RTS pin */
+ .start = GPIO_PF10,
+ .end = GPIO_PF10,
+ .flags = IORESOURCE_IO,
+ },
#endif
};
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+ P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
.name = "bfin-uart",
.id = 1,
- .num_resources = ARRAY_SIZE(bfin_uart_resources),
- .resource = bfin_uart_resources,
+ .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+ .resource = bfin_uart1_resources,
+ .dev = {
+ .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+ },
};
#endif
+#endif
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
#ifdef CONFIG_BFIN_SIR0
};
#endif
+#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#include <linux/mfd/adp5520.h>
+
+ /*
+ * ADP5520/5501 LEDs Data
+ */
+
+static struct led_info adp5520_leds[] = {
+ {
+ .name = "adp5520-led1",
+ .default_trigger = "none",
+ .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
+ },
+};
+
+static struct adp5520_leds_platform_data adp5520_leds_data = {
+ .num_leds = ARRAY_SIZE(adp5520_leds),
+ .leds = adp5520_leds,
+ .fade_in = ADP5520_FADE_T_600ms,
+ .fade_out = ADP5520_FADE_T_600ms,
+ .led_on_time = ADP5520_LED_ONT_600ms,
+};
+
+ /*
+ * ADP5520 Keypad Data
+ */
+
+static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
+ [ADP5520_KEY(3, 3)] = KEY_1,
+ [ADP5520_KEY(2, 3)] = KEY_2,
+ [ADP5520_KEY(1, 3)] = KEY_3,
+ [ADP5520_KEY(0, 3)] = KEY_UP,
+ [ADP5520_KEY(3, 2)] = KEY_4,
+ [ADP5520_KEY(2, 2)] = KEY_5,
+ [ADP5520_KEY(1, 2)] = KEY_6,
+ [ADP5520_KEY(0, 2)] = KEY_DOWN,
+ [ADP5520_KEY(3, 1)] = KEY_7,
+ [ADP5520_KEY(2, 1)] = KEY_8,
+ [ADP5520_KEY(1, 1)] = KEY_9,
+ [ADP5520_KEY(0, 1)] = KEY_DOT,
+ [ADP5520_KEY(3, 0)] = KEY_BACKSPACE,
+ [ADP5520_KEY(2, 0)] = KEY_0,
+ [ADP5520_KEY(1, 0)] = KEY_HELP,
+ [ADP5520_KEY(0, 0)] = KEY_ENTER,
+};
+
+static struct adp5520_keys_platform_data adp5520_keys_data = {
+ .rows_en_mask = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
+ .cols_en_mask = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
+ .keymap = adp5520_keymap,
+ .keymapsize = ARRAY_SIZE(adp5520_keymap),
+ .repeat = 0,
+};
+
+ /*
+ * ADP5520/5501 Multifuction Device Init Data
+ */
+
+static struct adp5520_platform_data adp5520_pdev_data = {
+ .leds = &adp5520_leds_data,
+ .keys = &adp5520_keys_data,
+};
+
+#endif
+
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
{
.irq = IRQ_PF8,
},
#endif
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+ {
+ I2C_BOARD_INFO("bfin-adv7393", 0x2B),
+ },
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("ad7879", 0x2C),
+ .irq = IRQ_PF8,
+ .platform_data = (void *)&bfin_ad7879_ts_info,
+ },
+#endif
+#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+ {
+ I2C_BOARD_INFO("pmic-adp5520", 0x32),
+ .irq = IRQ_PF9,
+ .platform_data = (void *)&adp5520_pdev_data,
+ },
+#endif
+#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+ {
+ I2C_BOARD_INFO("ssm2602", 0x1b),
+ },
+#endif
};
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+static struct resource bfin_sport0_uart_resources[] = {
+ {
+ .start = SPORT0_TCR1,
+ .end = SPORT0_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT0_RX,
+ .end = IRQ_SPORT0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT0_ERROR,
+ .end = IRQ_SPORT0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport0_peripherals[] = {
+ P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
+ P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
+};
+
static struct platform_device bfin_sport0_uart_device = {
.name = "bfin-sport-uart",
.id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
+ .resource = bfin_sport0_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+static struct resource bfin_sport1_uart_resources[] = {
+ {
+ .start = SPORT1_TCR1,
+ .end = SPORT1_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT1_RX,
+ .end = IRQ_SPORT1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT1_ERROR,
+ .end = IRQ_SPORT1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport1_peripherals[] = {
+ P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
+ P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
};
static struct platform_device bfin_sport1_uart_device = {
.name = "bfin-sport-uart",
.id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
+ .resource = bfin_sport1_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
+ },
};
#endif
+#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-#include <linux/input.h>
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
};
#endif
-#if defined(CONFIG_JOYSTICK_BFIN_ROTARY) || defined(CONFIG_JOYSTICK_BFIN_ROTARY_MODULE)
-#include <linux/input.h>
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
#include <asm/bfin_rotary.h>
static struct bfin_rotary_platform_data bfin_rotary_data = {
};
#endif
-static struct resource bfin_gpios_resources = {
- .start = 0,
- .end = MAX_BLACKFIN_GPIOS - 1,
- .flags = IORESOURCE_IRQ,
-};
-
-static struct platform_device bfin_gpios_device = {
- .name = "simple-gpio",
- .id = -1,
- .num_resources = 1,
- .resource = &bfin_gpios_resources,
-};
-
static const unsigned int cclk_vlev_datasheet[] =
{
VRPAIR(VLEV_100, 400000000),
&rtc_device,
#endif
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
- &sl811_hcd_device,
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
- &isp1362_hcd_device,
-#endif
-
#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
&bfin_isp1760_device,
#endif
&bfin_spi0_device,
#endif
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
- &bfin_fb_device,
-#endif
-
#if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
&bf52x_t350mcqb_device,
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
- &bfin_fb_adv7393_device,
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+ &bfin_lq035q1_device,
#endif
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
- &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
#endif
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
#endif
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
&bfin_sport1_uart_device,
#endif
+#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_JOYSTICK_BFIN_ROTARY) || defined(CONFIG_JOYSTICK_BFIN_ROTARY_MODULE)
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
&bfin_rotary_device,
#endif
&ezkit_flash_device,
#endif
- &bfin_gpios_device,
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+ &bfin_i2s,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+ &bfin_tdm,
+#endif
};
static int __init ezkit_init(void)
arch_initcall(ezkit_init);
+static struct platform_device *ezkit_early_devices[] __initdata = {
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+ &bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+ &bfin_sport1_uart_device,
+#endif
+#endif
+};
+
+void __init native_machine_early_platform_add_devices(void)
+{
+ printk(KERN_INFO "register early platform devices\n");
+ early_platform_add_devices(ezkit_early_devices,
+ ARRAY_SIZE(ezkit_early_devices));
+}
+
void native_machine_restart(char *cmd)
{
/* workaround reboot hang when booting from SPI */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff