# see Documentation/kbuild/kconfig-language.txt.
#
-mainmenu "uClinux/Blackfin (w/o MMU) Kernel Configuration"
+mainmenu "Blackfin Kernel Configuration"
config MMU
bool
bool
default y
-config BFIN
+config ZONE_DMA
bool
default y
default y
config GENERIC_IRQ_PROBE
- bool
+ bool
default y
config GENERIC_TIME
bool
default n
-config GENERIC_CALIBRATE_DELAY
+config GENERIC_GPIO
bool
default y
bool
default y
-config IRQCHIP_DEMUX_GPIO
- bool
- default y
+config HARDWARE_PM
+ def_bool y
+ depends on OPROFILE
source "init/Kconfig"
source "kernel/Kconfig.preempt"
prompt "CPU"
default BF533
+config BF522
+ bool "BF522"
+ help
+ BF522 Processor Support.
+
+config BF525
+ bool "BF525"
+ help
+ BF525 Processor Support.
+
+config BF527
+ bool "BF527"
+ help
+ BF527 Processor Support.
+
config BF531
bool "BF531"
help
help
BF537 Processor Support.
+config BF542
+ bool "BF542"
+ help
+ BF542 Processor Support.
+
+config BF544
+ bool "BF544"
+ help
+ BF544 Processor Support.
+
+config BF547
+ bool "BF547"
+ help
+ BF547 Processor Support.
+
+config BF548
+ bool "BF548"
+ help
+ BF548 Processor Support.
+
+config BF549
+ bool "BF549"
+ help
+ BF549 Processor Support.
+
config BF561
bool "BF561"
help
choice
prompt "Silicon Rev"
+ default BF_REV_0_1 if BF527
default BF_REV_0_2 if BF537
default BF_REV_0_3 if BF533
+ default BF_REV_0_0 if BF549
+
+config BF_REV_0_0
+ bool "0.0"
+ depends on (BF52x || BF54x)
+
+config BF_REV_0_1
+ bool "0.1"
+ depends on (BF52x || BF54x)
config BF_REV_0_2
bool "0.2"
bool "0.5"
depends on (BF561 || BF533 || BF532 || BF531)
+config BF_REV_ANY
+ bool "any"
+
+config BF_REV_NONE
+ bool "none"
+
endchoice
-config BFIN_DUAL_CORE
+config BF52x
bool
- depends on (BF561)
+ depends on (BF522 || BF525 || BF527)
default y
-config BFIN_SINGLE_CORE
+config BF53x
bool
- depends on !BFIN_DUAL_CORE
+ depends on (BF531 || BF532 || BF533 || BF534 || BF536 || BF537)
default y
-choice
- prompt "System type"
- default BFIN533_STAMP
- help
- Do NOT change the board here. Please use the top level
- configuration to ensure that all the other settings are
- correct.
-
-config BFIN533_EZKIT
- bool "BF533-EZKIT"
- depends on (BF533 || BF532 || BF531)
- help
- BF533-EZKIT-LITE board Support.
-
-config BFIN533_STAMP
- bool "BF533-STAMP"
- depends on (BF533 || BF532 || BF531)
- help
- BF533-STAMP board Support.
-
-config BFIN537_STAMP
- bool "BF537-STAMP"
- depends on (BF537 || BF536 || BF534)
- help
- BF537-STAMP board Support.
-
-config BFIN533_BLUETECHNIX_CM
- bool "Bluetechnix CM-BF533"
- depends on (BF533)
- help
- CM-BF533 support for EVAL- and DEV-Board.
-
-config BFIN537_BLUETECHNIX_CM
- bool "Bluetechnix CM-BF537"
- depends on (BF537)
- help
- CM-BF537 support for EVAL- and DEV-Board.
-
-config BFIN561_BLUETECHNIX_CM
- bool "BF561-CM"
- depends on (BF561)
- help
- CM-BF561 support for EVAL- and DEV-Board.
+config BF54x
+ bool
+ depends on (BF542 || BF544 || BF547 || BF548 || BF549)
+ default y
-config BFIN561_EZKIT
- bool "BF561-EZKIT"
+config BFIN_DUAL_CORE
+ bool
depends on (BF561)
- help
- BF561-EZKIT-LITE board Support.
-
-config PNAV10
- bool "PNAV 1.0 board"
- depends on (BF537)
- help
- PNAV 1.0 board Support.
-
-config GENERIC_BOARD
- bool "Custom"
- depends on (BF537 || BF536 \
- || BF534 || BF561 || BF535 || BF533 || BF532 || BF531)
- help
- GENERIC or Custom board Support.
+ default y
-endchoice
+config BFIN_SINGLE_CORE
+ bool
+ depends on !BFIN_DUAL_CORE
+ default y
config MEM_GENERIC_BOARD
bool
config MEM_MT48LC16M16A2TG_75
bool
depends on (BFIN533_EZKIT || BFIN561_EZKIT \
- || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM)
+ || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
+ || H8606_HVSISTEMAS)
default y
config MEM_MT48LC32M8A2_75
depends on (BFIN561_BLUETECHNIX_CM)
default y
+config MEM_MT48LC32M16A2TG_75
+ bool
+ depends on (BFIN527_EZKIT)
+ default y
+
config BFIN_SHARED_FLASH_ENET
bool
depends on (BFIN533_STAMP)
default y
+source "arch/blackfin/mach-bf527/Kconfig"
source "arch/blackfin/mach-bf533/Kconfig"
source "arch/blackfin/mach-bf561/Kconfig"
source "arch/blackfin/mach-bf537/Kconfig"
+source "arch/blackfin/mach-bf548/Kconfig"
menu "Board customizations"
to the kernel, you may specify one here. As a minimum, you should specify
the memory size and the root device (e.g., mem=8M, root=/dev/nfs).
-comment "Board Setup"
+comment "Clock/PLL Setup"
config CLKIN_HZ
int "Crystal Frequency in Hz"
default "11059200" if BFIN533_STAMP
default "27000000" if BFIN533_EZKIT
- default "25000000" if BFIN537_STAMP
+ default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
default "30000000" if BFIN561_EZKIT
default "24576000" if PNAV10
help
The frequency of CLKIN crystal oscillator on the board in Hz.
+config BFIN_KERNEL_CLOCK
+ bool "Re-program Clocks while Kernel boots?"
+ default n
+ help
+ This option decides if kernel clocks are re-programed from the
+ bootloader settings. If the clocks are not set, the SDRAM settings
+ are also not changed, and the Bootloader does 100% of the hardware
+ configuration.
+
+config PLL_BYPASS
+ bool "Bypass PLL"
+ depends on BFIN_KERNEL_CLOCK
+ default n
+
+config CLKIN_HALF
+ bool "Half Clock In"
+ depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+ default n
+ help
+ If this is set the clock will be divided by 2, before it goes to the PLL.
+
+config VCO_MULT
+ int "VCO Multiplier"
+ depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+ range 1 64
+ default "22" if BFIN533_EZKIT
+ default "45" if BFIN533_STAMP
+ default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
+ default "22" if BFIN533_BLUETECHNIX_CM
+ default "20" if BFIN537_BLUETECHNIX_CM
+ default "20" if BFIN561_BLUETECHNIX_CM
+ default "20" if BFIN561_EZKIT
+ default "16" if H8606_HVSISTEMAS
+ help
+ This controls the frequency of the on-chip PLL. This can be between 1 and 64.
+ PLL Frequency = (Crystal Frequency) * (this setting)
+
+choice
+ prompt "Core Clock Divider"
+ depends on BFIN_KERNEL_CLOCK
+ default CCLK_DIV_1
+ help
+ This sets the frequency of the core. It can be 1, 2, 4 or 8
+ Core Frequency = (PLL frequency) / (this setting)
+
+config CCLK_DIV_1
+ bool "1"
+
+config CCLK_DIV_2
+ bool "2"
+
+config CCLK_DIV_4
+ bool "4"
+
+config CCLK_DIV_8
+ bool "8"
+endchoice
+
+config SCLK_DIV
+ int "System Clock Divider"
+ depends on BFIN_KERNEL_CLOCK
+ range 1 15
+ default 5 if BFIN533_EZKIT
+ default 5 if BFIN533_STAMP
+ default 4 if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
+ default 5 if BFIN533_BLUETECHNIX_CM
+ default 4 if BFIN537_BLUETECHNIX_CM
+ default 4 if BFIN561_BLUETECHNIX_CM
+ default 5 if BFIN561_EZKIT
+ default 3 if H8606_HVSISTEMAS
+ help
+ This sets the frequency of the system clock (including SDRAM or DDR).
+ This can be between 1 and 15
+ System Clock = (PLL frequency) / (this setting)
+
+#
+# Max & Min Speeds for various Chips
+#
+config MAX_VCO_HZ
+ int
+ default 600000000 if BF522
+ default 600000000 if BF525
+ default 600000000 if BF527
+ default 400000000 if BF531
+ default 400000000 if BF532
+ default 750000000 if BF533
+ default 500000000 if BF534
+ default 400000000 if BF536
+ default 600000000 if BF537
+ default 533333333 if BF538
+ default 533333333 if BF539
+ default 600000000 if BF542
+ default 533333333 if BF544
+ default 533333333 if BF549
+ default 600000000 if BF561
+
+config MIN_VCO_HZ
+ int
+ default 50000000
+
+config MAX_SCLK_HZ
+ int
+ default 133333333
+
+config MIN_SCLK_HZ
+ int
+ default 27000000
+
+comment "Kernel Timer/Scheduler"
+
+source kernel/Kconfig.hz
+
+comment "Memory Setup"
+
config MEM_SIZE
int "SDRAM Memory Size in MBytes"
default 32 if BFIN533_EZKIT
+ default 64 if BFIN527_EZKIT
default 64 if BFIN537_STAMP
+ default 64 if BFIN548_EZKIT
default 64 if BFIN561_EZKIT
default 128 if BFIN533_STAMP
default 64 if PNAV10
+ default 32 if H8606_HVSISTEMAS
config MEM_ADD_WIDTH
int "SDRAM Memory Address Width"
+ depends on (!BF54x)
default 9 if BFIN533_EZKIT
default 9 if BFIN561_EZKIT
+ default 9 if H8606_HVSISTEMAS
+ default 10 if BFIN527_EZKIT
default 10 if BFIN537_STAMP
default 11 if BFIN533_STAMP
default 10 if PNAV10
+
+choice
+ prompt "DDR SDRAM Chip Type"
+ depends on BFIN548_EZKIT
+ default MEM_MT46V32M16_5B
+
+config MEM_MT46V32M16_6T
+ bool "MT46V32M16_6T"
+
+config MEM_MT46V32M16_5B
+ bool "MT46V32M16_5B"
+endchoice
+
config ENET_FLASH_PIN
int "PF port/pin used for flash and ethernet sharing"
depends on (BFIN533_STAMP)
config BOOT_LOAD
hex "Kernel load address for booting"
default "0x1000"
+ range 0x1000 0x20000000
help
This option allows you to set the load address of the kernel.
This can be useful if you are on a board which has a small amount
of memory or you wish to reserve some memory at the beginning of
the address space.
- Note that you generally want to keep this value at or above 4k
- (0x1000) as this will allow the kernel to capture NULL pointer
- references.
+ Note that you need to keep this value above 4k (0x1000) as this
+ memory region is used to capture NULL pointer references as well
+ as some core kernel functions.
-comment "LED Status Indicators"
- depends on (BFIN533_STAMP || BFIN533_BLUETECHNIX_CM)
-
-config BFIN_ALIVE_LED
- bool "Enable Board Alive"
- depends on (BFIN533_STAMP || BFIN533_BLUETECHNIX_CM)
- default n
- help
- Blink the LEDs you select when the kernel is running. Helps detect
- a hung kernel.
-
-config BFIN_ALIVE_LED_NUM
- int "LED"
- depends on BFIN_ALIVE_LED
- range 1 3 if BFIN533_STAMP
- default "3" if BFIN533_STAMP
+choice
+ prompt "Blackfin Exception Scratch Register"
+ default BFIN_SCRATCH_REG_RETN
help
- Select the LED (marked on the board) for you to blink.
+ Select the resource to reserve for the Exception handler:
+ - RETN: Non-Maskable Interrupt (NMI)
+ - RETE: Exception Return (JTAG/ICE)
+ - CYCLES: Performance counter
-config BFIN_IDLE_LED
- bool "Enable System Load/Idle LED"
- depends on (BFIN533_STAMP || BFIN533_BLUETECHNIX_CM)
- default n
- help
- Blinks the LED you select when to determine kernel load.
+ If you are unsure, please select "RETN".
-config BFIN_IDLE_LED_NUM
- int "LED"
- depends on BFIN_IDLE_LED
- range 1 3 if BFIN533_STAMP
- default "2" if BFIN533_STAMP
+config BFIN_SCRATCH_REG_RETN
+ bool "RETN"
help
- Select the LED (marked on the board) for you to blink.
-
-#
-# Sorry - but you need to put the hex address here -
-#
-
-# Flag Data register
-config BFIN_ALIVE_LED_PORT
- hex
- default 0xFFC00700 if (BFIN533_STAMP)
-
-# Peripheral Flag Direction Register
-config BFIN_ALIVE_LED_DPORT
- hex
- default 0xFFC00730 if (BFIN533_STAMP)
-
-config BFIN_ALIVE_LED_PIN
- hex
- default 0x04 if (BFIN533_STAMP && BFIN_ALIVE_LED_NUM = 1)
- default 0x08 if (BFIN533_STAMP && BFIN_ALIVE_LED_NUM = 2)
- default 0x10 if (BFIN533_STAMP && BFIN_ALIVE_LED_NUM = 3)
+ Use the RETN register in the Blackfin exception handler
+ as a stack scratch register. This means you cannot
+ safely use NMI on the Blackfin while running Linux, but
+ you can debug the system with a JTAG ICE and use the
+ CYCLES performance registers.
-config BFIN_IDLE_LED_PORT
- hex
- default 0xFFC00700 if (BFIN533_STAMP)
+ If you are unsure, please select "RETN".
-# Peripheral Flag Direction Register
-config BFIN_IDLE_LED_DPORT
- hex
- default 0xFFC00730 if (BFIN533_STAMP)
-
-config BFIN_IDLE_LED_PIN
- hex
- default 0x04 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 1)
- default 0x08 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 2)
- default 0x10 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 3)
+config BFIN_SCRATCH_REG_RETE
+ bool "RETE"
+ help
+ Use the RETE register in the Blackfin exception handler
+ as a stack scratch register. This means you cannot
+ safely use a JTAG ICE while debugging a Blackfin board,
+ but you can safely use the CYCLES performance registers
+ and the NMI.
-comment "Console UART Setup"
+ If you are unsure, please select "RETN".
-choice
- prompt "Baud Rate"
- default BAUD_57600
-config BAUD_9600
- bool "9600"
-config BAUD_19200
- bool "19200"
-config BAUD_38400
- bool "38400"
-config BAUD_57600
- bool "57600"
-config BAUD_115200
- bool "115200"
-endchoice
+config BFIN_SCRATCH_REG_CYCLES
+ bool "CYCLES"
+ help
+ Use the CYCLES register in the Blackfin exception handler
+ as a stack scratch register. This means you cannot
+ safely use the CYCLES performance registers on a Blackfin
+ board at anytime, but you can debug the system with a JTAG
+ ICE and use the NMI.
-choice
- prompt "Parity"
- default BAUD_NO_PARITY
-config BAUD_NO_PARITY
- bool "No Parity"
-config BAUD_PARITY
- bool "Parity"
-endchoice
+ If you are unsure, please select "RETN".
-choice
- prompt "Stop Bits"
- default BAUD_1_STOPBIT
-config BAUD_1_STOPBIT
- bool "1"
-config BAUD_2_STOPBIT
- bool "2"
endchoice
endmenu
menu "Blackfin Kernel Optimizations"
-comment "Timer Tick"
-
-source kernel/Kconfig.hz
-
comment "Memory Optimizations"
config I_ENTRY_L1
bool "Locate interrupt entry code in L1 Memory"
default y
help
- If enabled interrupt entry code (STORE/RESTORE CONTEXT) is linked
- into L1 instruction memory.(less latency)
+ If enabled, interrupt entry code (STORE/RESTORE CONTEXT) is linked
+ into L1 instruction memory. (less latency)
config EXCPT_IRQ_SYSC_L1
- bool "Locate entire ASM lowlevel excepetion / interrupt - Syscall and CPLB handler code in L1 Memory"
+ bool "Locate entire ASM lowlevel exception / interrupt - Syscall and CPLB handler code in L1 Memory"
default y
help
- If enabled entire ASM lowlevel exception and interrupt entry code (STORE/RESTORE CONTEXT) is linked
- into L1 instruction memory.(less latency)
+ If enabled, the entire ASM lowlevel exception and interrupt entry code
+ (STORE/RESTORE CONTEXT) is linked into L1 instruction memory.
+ (less latency)
config DO_IRQ_L1
bool "Locate frequently called do_irq dispatcher function in L1 Memory"
default y
help
- If enabled frequently called do_irq dispatcher function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called do_irq dispatcher function is linked
+ into L1 instruction memory. (less latency)
config CORE_TIMER_IRQ_L1
bool "Locate frequently called timer_interrupt() function in L1 Memory"
default y
help
- If enabled frequently called timer_interrupt() function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called timer_interrupt() function is linked
+ into L1 instruction memory. (less latency)
config IDLE_L1
bool "Locate frequently idle function in L1 Memory"
default y
help
- If enabled frequently called idle function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called idle function is linked
+ into L1 instruction memory. (less latency)
config SCHEDULE_L1
bool "Locate kernel schedule function in L1 Memory"
default y
help
- If enabled frequently called kernel schedule is linked
- into L1 instruction memory.(less latency)
+ If enabled, the frequently called kernel schedule is linked
+ into L1 instruction memory. (less latency)
config ARITHMETIC_OPS_L1
bool "Locate kernel owned arithmetic functions in L1 Memory"
default y
help
- If enabled arithmetic functions are linked
- into L1 instruction memory.(less latency)
+ If enabled, arithmetic functions are linked
+ into L1 instruction memory. (less latency)
config ACCESS_OK_L1
bool "Locate access_ok function in L1 Memory"
default y
help
- If enabled access_ok function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the access_ok function is linked
+ into L1 instruction memory. (less latency)
config MEMSET_L1
bool "Locate memset function in L1 Memory"
default y
help
- If enabled memset function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the memset function is linked
+ into L1 instruction memory. (less latency)
config MEMCPY_L1
bool "Locate memcpy function in L1 Memory"
default y
help
- If enabled memcpy function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the memcpy function is linked
+ into L1 instruction memory. (less latency)
config SYS_BFIN_SPINLOCK_L1
bool "Locate sys_bfin_spinlock function in L1 Memory"
default y
help
- If enabled sys_bfin_spinlock function is linked
- into L1 instruction memory.(less latency)
+ If enabled, sys_bfin_spinlock function is linked
+ into L1 instruction memory. (less latency)
config IP_CHECKSUM_L1
bool "Locate IP Checksum function in L1 Memory"
default n
help
- If enabled IP Checksum function is linked
- into L1 instruction memory.(less latency)
+ If enabled, the IP Checksum function is linked
+ into L1 instruction memory. (less latency)
config CACHELINE_ALIGNED_L1
bool "Locate cacheline_aligned data to L1 Data Memory"
- default y
+ default y if !BF54x
+ default n if BF54x
depends on !BF531
help
- If enabled cacheline_anligned data is linked
- into L1 data memory.(less latency)
+ If enabled, cacheline_anligned data is linked
+ into L1 data memory. (less latency)
config SYSCALL_TAB_L1
bool "Locate Syscall Table L1 Data Memory"
default n
depends on !BF531
help
- If enabled the Syscall LUT is linked
- into L1 data memory.(less latency)
+ If enabled, the Syscall LUT is linked
+ into L1 data memory. (less latency)
config CPLB_SWITCH_TAB_L1
bool "Locate CPLB Switch Tables L1 Data Memory"
default n
depends on !BF531
help
- If enabled the CPLB Switch Tables are linked
- into L1 data memory.(less latency)
+ If enabled, the CPLB Switch Tables are linked
+ into L1 data memory. (less latency)
endmenu
source "mm/Kconfig"
+config LARGE_ALLOCS
+ bool "Allow allocating large blocks (> 1MB) of memory"
+ help
+ Allow the slab memory allocator to keep chains for very large
+ memory sizes - upto 32MB. You may need this if your system has
+ a lot of RAM, and you need to able to allocate very large
+ contiguous chunks. If unsure, say N.
+
+config BFIN_GPTIMERS
+ tristate "Enable Blackfin General Purpose Timers API"
+ default n
+ help
+ Enable support for the General Purpose Timers API. If you
+ are unsure, say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called gptimers.ko.
+
config BFIN_DMA_5XX
bool "Enable DMA Support"
- depends on (BF533 || BF532 || BF531 || BF537 || BF536 || BF534 || BF561)
+ depends on (BF52x || BF53x || BF561 || BF54x)
default y
help
DMA driver for BF5xx.
choice
prompt "Uncached SDRAM region"
default DMA_UNCACHED_1M
- depends BFIN_DMA_5XX
+ depends on BFIN_DMA_5XX
config DMA_UNCACHED_2M
bool "Enable 2M DMA region"
config DMA_UNCACHED_1M
comment "Cache Support"
-config BLKFIN_CACHE
+config BFIN_ICACHE
bool "Enable ICACHE"
-config BLKFIN_DCACHE
+config BFIN_DCACHE
bool "Enable DCACHE"
-config BLKFIN_DCACHE_BANKA
+config BFIN_DCACHE_BANKA
bool "Enable only 16k BankA DCACHE - BankB is SRAM"
- depends on BLKFIN_DCACHE && !BF531
+ depends on BFIN_DCACHE && !BF531
default n
-config BLKFIN_CACHE_LOCK
- bool "Enable Cache Locking"
+config BFIN_ICACHE_LOCK
+ bool "Enable Instruction Cache Locking"
choice
prompt "Policy"
- depends on BLKFIN_DCACHE
- default BLKFIN_WB
-config BLKFIN_WB
+ depends on BFIN_DCACHE
+ default BFIN_WB
+config BFIN_WB
bool "Write back"
help
Write Back Policy:
If you are unsure of the options and you want to be safe,
then go with Write Through.
-config BLKFIN_WT
+config BFIN_WT
bool "Write through"
help
Write Back Policy:
Set the max memory pieces for the L1 SRAM allocation algorithm.
Min value is 16. Max value is 1024.
-menu "Clock Settings"
-
-
-config BFIN_KERNEL_CLOCK
- bool "Re-program Clocks while Kernel boots?"
- default n
- help
- This option decides if kernel clocks are re-programed from the
- bootloader settings. If the clocks are not set, the SDRAM settings
- are also not changed, and the Bootloader does 100% of the hardware
- configuration.
-
-config VCO_MULT
- int "VCO Multiplier"
- depends on BFIN_KERNEL_CLOCK
- default "22" if BFIN533_EZKIT
- default "45" if BFIN533_STAMP
- default "20" if BFIN537_STAMP
- default "22" if BFIN533_BLUETECHNIX_CM
- default "20" if BFIN537_BLUETECHNIX_CM
- default "20" if BFIN561_BLUETECHNIX_CM
- default "20" if BFIN561_EZKIT
-
-config CCLK_DIV
- int "Core Clock Divider"
- depends on BFIN_KERNEL_CLOCK
- default 1 if BFIN533_EZKIT
- default 1 if BFIN533_STAMP
- default 1 if BFIN537_STAMP
- default 1 if BFIN533_BLUETECHNIX_CM
- default 1 if BFIN537_BLUETECHNIX_CM
- default 1 if BFIN561_BLUETECHNIX_CM
- default 1 if BFIN561_EZKIT
-
-config SCLK_DIV
- int "System Clock Divider"
- depends on BFIN_KERNEL_CLOCK
- default 5 if BFIN533_EZKIT
- default 5 if BFIN533_STAMP
- default 4 if BFIN537_STAMP
- default 5 if BFIN533_BLUETECHNIX_CM
- default 4 if BFIN537_BLUETECHNIX_CM
- default 4 if BFIN561_BLUETECHNIX_CM
- default 5 if BFIN561_EZKIT
-
-config CLKIN_HALF
- bool "Half ClockIn"
- depends on BFIN_KERNEL_CLOCK
- default n
-
-config PLL_BYPASS
- bool "Bypass PLL"
- depends on BFIN_KERNEL_CLOCK
- default n
-
-endmenu
-
comment "Asynchonous Memory Configuration"
-menu "EBIU_AMBCTL Global Control"
+menu "EBIU_AMGCTL Global Control"
config C_AMCKEN
bool "Enable CLKOUT"
default y
config C_CDPRIO
bool "DMA has priority over core for ext. accesses"
+ depends on !BF54x
default n
config C_B0PEN
default 0x99B3
endmenu
+config EBIU_MBSCTLVAL
+ hex "EBIU Bank Select Control Register"
+ depends on BF54x
+ default 0
+
+config EBIU_MODEVAL
+ hex "Flash Memory Mode Control Register"
+ depends on BF54x
+ default 1
+
+config EBIU_FCTLVAL
+ hex "Flash Memory Bank Control Register"
+ depends on BF54x
+ default 6
endmenu
#############################################################################
depends on PM_WAKEUP_GPIO_BY_SIC_IWR
default 0x80000000 if (BF537 || BF536 || BF534)
default 0x100000 if (BF533 || BF532 || BF531)
+ default 0x800000 if (BF549 || BF548 || BF547 || BF542)
+ default 0x800000 if (BF527 || BF524 || BF522)
config PM_WAKEUP_GPIO_NUMBER
int "Wakeup GPIO number"
endmenu
-if (BF537 || BF533)
+if (BF537 || BF533 || BF54x)
menu "CPU Frequency scaling"
source "fs/Kconfig"
-source "arch/blackfin/oprofile/Kconfig"
-
-menu "Kernel hacking"
+source "kernel/Kconfig.instrumentation"
-source "lib/Kconfig.debug"
-
-config DEBUG_HWERR
- bool "Hardware error interrupt debugging"
- depends on DEBUG_KERNEL
- help
- When enabled, the hardware error interrupt is never disabled, and
- will happen immediately when an error condition occurs. This comes
- at a slight cost in code size, but is necessary if you are getting
- hardware error interrupts and need to know where they are coming
- from.
-
-config DEBUG_ICACHE_CHECK
- bool "Check Instruction cache coherancy"
- depends on DEBUG_KERNEL
- depends on DEBUG_HWERR
- help
- Say Y here if you are getting wierd unexplained errors. This will
- ensure that icache is what SDRAM says it should be, by doing a
- byte wise comparision between SDRAM and instruction cache. This
- also relocates the irq_panic() function to L1 memory, (which is
- un-cached).
-
-config DEBUG_KERNEL_START
- bool "Debug Kernel Startup"
- depends on DEBUG_KERNEL
- help
- Say Y here to put in an mini-execption handler before the kernel
- replaces the bootloader exception handler. This will stop kernels
- from dieing at startup with no visible error messages.
-
-config DEBUG_SERIAL_EARLY_INIT
- bool "Initialize serial driver early"
- default n
- depends on SERIAL_BFIN
- help
- Say Y here if you want to get kernel output early when kernel
- crashes before the normal console initialization. If this option
- is enable, console output will always go to the ttyBF0, no matter
- what kernel boot paramters you set.
-
-config DEBUG_HUNT_FOR_ZERO
- bool "Catch NULL pointer reads/writes"
- default y
- help
- Say Y here to catch reads/writes to anywhere in the memory range
- from 0x0000 - 0x0FFF (the first 4k) of memory. This is useful in
- catching common programming errors such as NULL pointer dereferences.
-
- Misbehaving applications will be killed (generate a SEGV) while the
- kernel will trigger a panic.
-
- Enabling this option will take up an extra entry in CPLB table.
- Otherwise, there is no extra overhead.
-
-config DEBUG_BFIN_NO_KERN_HWTRACE
- bool "Trace user apps (turn off hwtrace in kernel)"
- default n
- help
- Some pieces of the kernel contain a lot of flow changes which can
- quickly fill up the hardware trace buffer. When debugging crashes,
- the hardware trace may indicate that the problem lies in kernel
- space when in reality an application is buggy.
-
- Say Y here to disable hardware tracing in some known "jumpy" pieces
- of code so that the trace buffer will extend further back.
-
-config DUAL_CORE_TEST_MODULE
- tristate "Dual Core Test Module"
- depends on (BF561)
- default n
- help
- Say Y here to build-in dual core test module for dual core test.
-
-config CPLB_INFO
- bool "Display the CPLB information"
- help
- Display the CPLB information.
-
-config ACCESS_CHECK
- bool "Check the user pointer address"
- default y
- help
- Usually the pointer transfer from user space is checked to see if its
- address is in the kernel space.
-
- Say N here to disable that check to improve the performance.
-
-endmenu
+source "arch/blackfin/Kconfig.debug"
source "security/Kconfig"
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff