range 1 64
default "22" if BFIN533_EZKIT
default "45" if BFIN533_STAMP
- default "20" if (BFIN537_STAMP || BFIN527_EZKIT)
+ default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
default "22" if BFIN533_BLUETECHNIX_CM
default "20" if BFIN537_BLUETECHNIX_CM
default "20" if BFIN561_BLUETECHNIX_CM
range 1 15
default 5 if BFIN533_EZKIT
default 5 if BFIN533_STAMP
- default 4 if (BFIN537_STAMP || BFIN527_EZKIT)
+ default 4 if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
default 5 if BFIN533_BLUETECHNIX_CM
default 4 if BFIN537_BLUETECHNIX_CM
default 4 if BFIN561_BLUETECHNIX_CM
default 32 if BFIN533_EZKIT
default 64 if BFIN527_EZKIT
default 64 if BFIN537_STAMP
+ default 64 if BFIN548_EZKIT
default 64 if BFIN561_EZKIT
default 128 if BFIN533_STAMP
default 64 if PNAV10
config MEM_ADD_WIDTH
int "SDRAM Memory Address Width"
+ depends on (!BF54x)
default 9 if BFIN533_EZKIT
default 9 if BFIN561_EZKIT
default 9 if H8606_HVSISTEMAS
default 11 if BFIN533_STAMP
default 10 if PNAV10
+
+choice
+ prompt "DDR SDRAM Chip Type"
+ depends on BFIN548_EZKIT
+ default MEM_MT46V32M16_5B
+
+config MEM_MT46V32M16_6T
+ bool "MT46V32M16_6T"
+
+config MEM_MT46V32M16_5B
+ bool "MT46V32M16_5B"
+endchoice
+
config ENET_FLASH_PIN
int "PF port/pin used for flash and ethernet sharing"
depends on (BFIN533_STAMP)
memory region is used to capture NULL pointer references as well
as some core kernel functions.
-comment "LED Status Indicators"
- depends on (BFIN533_STAMP || BFIN533_BLUETECHNIX_CM)
-
-config BFIN_ALIVE_LED
- bool "Enable Board Alive"
- depends on (BFIN533_STAMP || BFIN533_BLUETECHNIX_CM)
- default n
- help
- Blink the LEDs you select when the kernel is running. Helps detect
- a hung kernel.
-
-config BFIN_ALIVE_LED_NUM
- int "LED"
- depends on BFIN_ALIVE_LED
- range 1 3 if BFIN533_STAMP
- default "3" if BFIN533_STAMP
- help
- Select the LED (marked on the board) for you to blink.
-
-config BFIN_IDLE_LED
- bool "Enable System Load/Idle LED"
- depends on (BFIN533_STAMP || BFIN533_BLUETECHNIX_CM)
- default n
- help
- Blinks the LED you select when to determine kernel load.
-
-config BFIN_IDLE_LED_NUM
- int "LED"
- depends on BFIN_IDLE_LED
- range 1 3 if BFIN533_STAMP
- default "2" if BFIN533_STAMP
- help
- Select the LED (marked on the board) for you to blink.
-
choice
prompt "Blackfin Exception Scratch Register"
default BFIN_SCRATCH_REG_RETN
endchoice
-#
-# Sorry - but you need to put the hex address here -
-#
-
-# Flag Data register
-config BFIN_ALIVE_LED_PORT
- hex
- default 0xFFC00700 if (BFIN533_STAMP)
-
-# Peripheral Flag Direction Register
-config BFIN_ALIVE_LED_DPORT
- hex
- default 0xFFC00730 if (BFIN533_STAMP)
-
-config BFIN_ALIVE_LED_PIN
- hex
- default 0x04 if (BFIN533_STAMP && BFIN_ALIVE_LED_NUM = 1)
- default 0x08 if (BFIN533_STAMP && BFIN_ALIVE_LED_NUM = 2)
- default 0x10 if (BFIN533_STAMP && BFIN_ALIVE_LED_NUM = 3)
-
-config BFIN_IDLE_LED_PORT
- hex
- default 0xFFC00700 if (BFIN533_STAMP)
-
-# Peripheral Flag Direction Register
-config BFIN_IDLE_LED_DPORT
- hex
- default 0xFFC00730 if (BFIN533_STAMP)
-
-config BFIN_IDLE_LED_PIN
- hex
- default 0x04 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 1)
- default 0x08 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 2)
- default 0x10 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 3)
-
endmenu