#include <linux/irq.h>
#include <linux/platform_device.h>
-#include <linux/ide.h>
#include <linux/i2c.h>
+#include <linux/pwm_backlight.h>
#include <media/soc_camera.h>
#include <asm/gpio.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/camera.h>
+#include <mach/i2c.h>
+#include <mach/camera.h>
#include <asm/mach/map.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/pcm990_baseboard.h>
+#include <mach/pxa27x.h>
+#include <mach/audio.h>
+#include <mach/mmc.h>
+#include <mach/ohci.h>
+#include <mach/pcm990_baseboard.h>
+#include <mach/pxafb.h>
+
+#include "devices.h"
+#include "generic.h"
+
+static unsigned long pcm990_pin_config[] __initdata = {
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO112_MMC_CMD,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ /* USB */
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+ /* PWM0 */
+ GPIO16_PWM0_OUT,
+
+ /* I2C */
+ GPIO117_I2C_SCL,
+ GPIO118_I2C_SDA,
+};
/*
- * The PCM-990 development baseboard uses PCM-027's hardeware in the
+ * pcm990_lcd_power - control power supply to the LCD
+ * @on: 0 = switch off, 1 = switch on
+ *
+ * Called by the pxafb driver
+ */
+#ifndef CONFIG_PCM990_DISPLAY_NONE
+static void pcm990_lcd_power(int on, struct fb_var_screeninfo *var)
+{
+ if (on) {
+ /* enable LCD-Latches
+ * power on LCD
+ */
+ __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) =
+ PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON;
+ } else {
+ /* disable LCD-Latches
+ * power off LCD
+ */
+ __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = 0x00;
+ }
+}
+#endif
+
+#if defined(CONFIG_PCM990_DISPLAY_SHARP)
+static struct pxafb_mode_info fb_info_sharp_lq084v1dg21 = {
+ .pixclock = 28000,
+ .xres = 640,
+ .yres = 480,
+ .bpp = 16,
+ .hsync_len = 20,
+ .left_margin = 103,
+ .right_margin = 47,
+ .vsync_len = 6,
+ .upper_margin = 28,
+ .lower_margin = 5,
+ .sync = 0,
+ .cmap_greyscale = 0,
+};
+
+static struct pxafb_mach_info pcm990_fbinfo __initdata = {
+ .modes = &fb_info_sharp_lq084v1dg21,
+ .num_modes = 1,
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+ .pxafb_lcd_power = pcm990_lcd_power,
+};
+#elif defined(CONFIG_PCM990_DISPLAY_NEC)
+struct pxafb_mode_info fb_info_nec_nl6448bc20_18d = {
+ .pixclock = 39720,
+ .xres = 640,
+ .yres = 480,
+ .bpp = 16,
+ .hsync_len = 32,
+ .left_margin = 16,
+ .right_margin = 48,
+ .vsync_len = 2,
+ .upper_margin = 12,
+ .lower_margin = 17,
+ .sync = 0,
+ .cmap_greyscale = 0,
+};
+
+static struct pxafb_mach_info pcm990_fbinfo __initdata = {
+ .modes = &fb_info_nec_nl6448bc20_18d,
+ .num_modes = 1,
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+ .pxafb_lcd_power = pcm990_lcd_power,
+};
+#endif
+
+static struct platform_pwm_backlight_data pcm990_backlight_data = {
+ .pwm_id = 0,
+ .max_brightness = 1023,
+ .dft_brightness = 1023,
+ .pwm_period_ns = 78770,
+};
+
+static struct platform_device pcm990_backlight_device = {
+ .name = "pwm-backlight",
+ .dev = {
+ .parent = &pxa27x_device_pwm0.dev,
+ .platform_data = &pcm990_backlight_data,
+ },
+};
+
+/*
+ * The PCM-990 development baseboard uses PCM-027's hardware in the
* following way:
*
* - LCD support is in use
GPIO_bit(PCM990_CTRL_INT_IRQ_GPIO);
if (likely(pending)) {
irq = PCM027_IRQ(0) + __ffs(pending);
- desc = irq_desc + irq;
- desc_handle_irq(irq, desc);
+ generic_handle_irq(irq);
}
pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
} while (pending);
{
int err;
- /*
- * enable GPIO for PXA27x MMC controller
- */
- pxa_gpio_mode(GPIO32_MMCCLK_MD);
- pxa_gpio_mode(GPIO112_MMCCMD_MD);
- pxa_gpio_mode(GPIO92_MMCDAT0_MD);
- pxa_gpio_mode(GPIO109_MMCDAT1_MD);
- pxa_gpio_mode(GPIO110_MMCDAT2_MD);
- pxa_gpio_mode(GPIO111_MMCDAT3_MD);
-
err = request_irq(PCM027_MMCDET_IRQ, mci_detect_int, IRQF_DISABLED,
"MMC card detect", data);
if (err)
.exit = pcm990_mci_exit,
};
-/*
- * init OHCI hardware to work with
- *
- * Note: Only USB port 1 (host only) is connected
- *
- * GPIO88 (USBHPWR#1): overcurrent in, overcurrent when low
- * GPIO89 (USBHPEN#1): power-on out, on when low
- */
-static int pcm990_ohci_init(struct device *dev)
-{
- pxa_gpio_mode(PCM990_USB_OVERCURRENT);
- pxa_gpio_mode(PCM990_USB_PWR_EN);
- /*
- * disable USB port 2 and 3
- * power sense is active low
- */
- UHCHR = ((UHCHR) | UHCHR_PCPL | UHCHR_PSPL | UHCHR_SSEP2 |
- UHCHR_SSEP3) & ~(UHCHR_SSEP1 | UHCHR_SSE);
- /*
- * wait 10ms after Power on
- * overcurrent per port
- * power switch per port
- */
- UHCRHDA = (5<<24) | (1<<11) | (1<<8); /* FIXME: Required? */
-
- return 0;
-}
-
static struct pxaohci_platform_data pcm990_ohci_platform_data = {
.port_mode = PMM_PERPORT_MODE,
- .init = pcm990_ohci_init,
- .exit = NULL,
+ .flags = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW,
+ .power_on_delay = 10,
};
/*
* PXA27x Camera specific stuff
*/
#if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE)
+static unsigned long pcm990_camera_pin_config[] = {
+ /* CIF */
+ GPIO98_CIF_DD_0,
+ GPIO105_CIF_DD_1,
+ GPIO104_CIF_DD_2,
+ GPIO103_CIF_DD_3,
+ GPIO95_CIF_DD_4,
+ GPIO94_CIF_DD_5,
+ GPIO93_CIF_DD_6,
+ GPIO108_CIF_DD_7,
+ GPIO107_CIF_DD_8,
+ GPIO106_CIF_DD_9,
+ GPIO42_CIF_MCLK,
+ GPIO45_CIF_PCLK,
+ GPIO43_CIF_FV,
+ GPIO44_CIF_LV,
+};
+
static int pcm990_pxacamera_init(struct device *dev)
{
- pxa_gpio_mode(GPIO98_CIF_DD_0_MD);
- pxa_gpio_mode(GPIO105_CIF_DD_1_MD);
- pxa_gpio_mode(GPIO104_CIF_DD_2_MD);
- pxa_gpio_mode(GPIO103_CIF_DD_3_MD);
- pxa_gpio_mode(GPIO95_CIF_DD_4_MD);
- pxa_gpio_mode(GPIO94_CIF_DD_5_MD);
- pxa_gpio_mode(GPIO93_CIF_DD_6_MD);
- pxa_gpio_mode(GPIO108_CIF_DD_7_MD);
- pxa_gpio_mode(GPIO107_CIF_DD_8_MD);
- pxa_gpio_mode(GPIO106_CIF_DD_9_MD);
- pxa_gpio_mode(GPIO42_CIF_MCLK_MD);
- pxa_gpio_mode(GPIO45_CIF_PCLK_MD);
- pxa_gpio_mode(GPIO43_CIF_FV_MD);
- pxa_gpio_mode(GPIO44_CIF_LV_MD);
-
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_camera_pin_config));
return 0;
}
#include <linux/i2c/pca953x.h>
static struct pca953x_platform_data pca9536_data = {
- .gpio_base = NR_BUILTIN_GPIO + 1,
+ .gpio_base = NR_BUILTIN_GPIO,
};
-static struct soc_camera_link iclink[] = {
- {
- .bus_id = 0, /* Must match with the camera ID above */
- .gpio = NR_BUILTIN_GPIO + 1,
- }, {
- .bus_id = 0, /* Must match with the camera ID above */
+static int gpio_bus_switch;
+
+static int pcm990_camera_set_bus_param(struct soc_camera_link *link,
+ unsigned long flags)
+{
+ if (gpio_bus_switch <= 0) {
+ if (flags == SOCAM_DATAWIDTH_10)
+ return 0;
+ else
+ return -EINVAL;
+ }
+
+ if (flags & SOCAM_DATAWIDTH_8)
+ gpio_set_value(gpio_bus_switch, 1);
+ else
+ gpio_set_value(gpio_bus_switch, 0);
+
+ return 0;
+}
+
+static unsigned long pcm990_camera_query_bus_param(struct soc_camera_link *link)
+{
+ int ret;
+
+ if (!gpio_bus_switch) {
+ ret = gpio_request(NR_BUILTIN_GPIO, "camera");
+ if (!ret) {
+ gpio_bus_switch = NR_BUILTIN_GPIO;
+ gpio_direction_output(gpio_bus_switch, 0);
+ } else
+ gpio_bus_switch = -EINVAL;
}
+
+ if (gpio_bus_switch > 0)
+ return SOCAM_DATAWIDTH_8 | SOCAM_DATAWIDTH_10;
+ else
+ return SOCAM_DATAWIDTH_10;
+}
+
+static struct soc_camera_link iclink = {
+ .bus_id = 0, /* Must match with the camera ID above */
+ .query_bus_param = pcm990_camera_query_bus_param,
+ .set_bus_param = pcm990_camera_set_bus_param,
};
/* Board I2C devices. */
.platform_data = &pca9536_data,
}, {
I2C_BOARD_INFO("mt9v022", 0x48),
- .platform_data = &iclink[0], /* With extender */
+ .platform_data = &iclink, /* With extender */
}, {
I2C_BOARD_INFO("mt9m001", 0x5d),
- .platform_data = &iclink[0], /* With extender */
+ .platform_data = &iclink, /* With extender */
},
};
#endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */
/*
- * AC97 support
- * Note: The connected AC97 mixer also reports interrupts at PCM990_AC97_IRQ
- */
-static struct resource pxa27x_ac97_resources[] = {
- [0] = {
- .start = 0x40500000,
- .end = 0x40500000 + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_AC97,
- .end = IRQ_AC97,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 pxa_ac97_dmamask = 0xffffffffUL;
-
-static struct platform_device pxa27x_device_ac97 = {
- .name = "pxa2xx-ac97",
- .id = -1,
- .dev = {
- .dma_mask = &pxa_ac97_dmamask,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(pxa27x_ac97_resources),
- .resource = pxa27x_ac97_resources,
-};
-
-/*
* enable generic access to the base board control CPLDs U6 and U7
*/
static struct map_desc pcm990_io_desc[] __initdata = {
*/
void __init pcm990_baseboard_init(void)
{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_pin_config));
+
/* register CPLD access */
- iotable_init(pcm990_io_desc, ARRAY_SIZE(pcm990_io_desc));
+ iotable_init(ARRAY_AND_SIZE(pcm990_io_desc));
/* register CPLD's IRQ controller */
pcm990_init_irq();
- platform_device_register(&pxa27x_device_ac97);
+#ifndef CONFIG_PCM990_DISPLAY_NONE
+ set_pxa_fb_info(&pcm990_fbinfo);
+#endif
+ platform_device_register(&pcm990_backlight_device);
/* MMC */
pxa_set_mci_info(&pcm990_mci_platform_data);
pxa_set_ohci_info(&pcm990_ohci_platform_data);
pxa_set_i2c_info(NULL);
+ pxa_set_ac97_info(NULL);
#if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE)
pxa_set_camera_info(&pcm990_pxacamera_platform_data);
- i2c_register_board_info(0, pcm990_i2c_devices,
- ARRAY_SIZE(pcm990_i2c_devices));
+ i2c_register_board_info(0, ARRAY_AND_SIZE(pcm990_i2c_devices));
#endif
- printk(KERN_INFO"PCM-990 Evaluation baseboard initialized\n");
+ printk(KERN_INFO "PCM-990 Evaluation baseboard initialized\n");
}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff