ASoC: add two more bitfields for PXA SSP

[safe/jmp/linux-2.6] / arch / arm / mach-pxa / pcm990-baseboard.c

diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c
index 420c9b3..34841c7 100644 (file)
--- a/arch/arm/mach-pxa/pcm990-baseboard.c
+++ b/arch/arm/mach-pxa/pcm990-baseboard.c
@@ -55,6 +55,10 @@ static unsigned long pcm990_pin_config[] __initdata = {
        GPIO89_USBH1_PEN,
        /* PWM0 */
        GPIO16_PWM0_OUT,
+
+       /* I2C */
+       GPIO117_I2C_SCL,
+       GPIO118_I2C_SDA,
 };
 
 /*
@@ -100,8 +104,7 @@ static struct pxafb_mode_info fb_info_sharp_lq084v1dg21 = {
 static struct pxafb_mach_info pcm990_fbinfo __initdata = {
        .modes                  = &fb_info_sharp_lq084v1dg21,
        .num_modes              = 1,
-       .lccr0                  = LCCR0_PAS,
-       .lccr3                  = LCCR3_PCP,
+       .lcd_conn               = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
        .pxafb_lcd_power        = pcm990_lcd_power,
 };
 #elif defined(CONFIG_PCM990_DISPLAY_NEC)
@@ -123,8 +126,7 @@ struct pxafb_mode_info fb_info_nec_nl6448bc20_18d = {
 static struct pxafb_mach_info pcm990_fbinfo __initdata = {
        .modes                  = &fb_info_nec_nl6448bc20_18d,
        .num_modes              = 1,
-       .lccr0                  = LCCR0_Act,
-       .lccr3                  = LCCR3_PixFlEdg,
+       .lcd_conn               = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
        .pxafb_lcd_power        = pcm990_lcd_power,
 };
 #endif
@@ -262,8 +264,7 @@ static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc)
                                        GPIO_bit(PCM990_CTRL_INT_IRQ_GPIO);
                if (likely(pending)) {
                        irq = PCM027_IRQ(0) + __ffs(pending);
-                       desc = irq_desc + irq;
-                       desc_handle_irq(irq, desc);
+                       generic_handle_irq(irq);
                }
                pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
        } while (pending);
@@ -328,36 +329,10 @@ static struct pxamci_platform_data pcm990_mci_platform_data = {
        .exit           = pcm990_mci_exit,
 };
 
-/*
- * init OHCI hardware to work with
- *
- * Note: Only USB port 1 (host only) is connected
- *
- * GPIO88 (USBHPWR#1): overcurrent in, overcurrent when low
- * GPIO89 (USBHPEN#1): power-on out, on when low
- */
-static int pcm990_ohci_init(struct device *dev)
-{
-       /*
-        * disable USB port 2 and 3
-        * power sense is active low
-        */
-       UHCHR = ((UHCHR) | UHCHR_PCPL | UHCHR_PSPL | UHCHR_SSEP2 |
-                               UHCHR_SSEP3) & ~(UHCHR_SSEP1 | UHCHR_SSE);
-       /*
-        * wait 10ms after Power on
-        * overcurrent per port
-        * power switch per port
-        */
-       UHCRHDA = (5<<24) | (1<<11) | (1<<8);   /* FIXME: Required? */
-
-       return 0;
-}
-
 static struct pxaohci_platform_data pcm990_ohci_platform_data = {
        .port_mode      = PMM_PERPORT_MODE,
-       .init           = pcm990_ohci_init,
-       .exit           = NULL,
+       .flags          = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW,
+       .power_on_delay = 10,
 };
 
 /*
@@ -412,6 +387,7 @@ static struct soc_camera_link iclink[] = {
                .gpio   = NR_BUILTIN_GPIO + 1,
        }, {
                .bus_id = 0, /* Must match with the camera ID above */
+               .gpio   = -ENXIO,
        }
 };