#include <linux/interrupt.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/smc91x.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <mach/pxa2xx_spi.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/hardware/sa1111.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/lubbock.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/mmc.h>
+#include <mach/pxa25x.h>
+#include <mach/gpio.h>
+#include <mach/audio.h>
+#include <mach/lubbock.h>
+#include <mach/udc.h>
+#include <mach/irda.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/pm.h>
#include "generic.h"
+#include "clock.h"
+#include "devices.h"
+
+static unsigned long lubbock_pin_config[] __initdata = {
+ GPIO15_nCS_1, /* CS1 - Flash */
+ GPIO78_nCS_2, /* CS2 - Baseboard FGPA */
+ GPIO79_nCS_3, /* CS3 - SMC ethernet */
+ GPIO80_nCS_4, /* CS4 - SA1111 */
+
+ /* SSP data pins */
+ GPIO23_SSP1_SCLK,
+ GPIO25_SSP1_TXD,
+ GPIO26_SSP1_RXD,
+
+ /* LCD - 16bpp DSTN */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+
+ /* BTUART */
+ GPIO42_BTUART_RXD,
+ GPIO43_BTUART_TXD,
+ GPIO44_BTUART_CTS,
+ GPIO45_BTUART_RTS,
+
+ /* PC Card */
+ GPIO48_nPOE,
+ GPIO49_nPWE,
+ GPIO50_nPIOR,
+ GPIO51_nPIOW,
+ GPIO52_nPCE_1,
+ GPIO53_nPCE_2,
+ GPIO54_nPSKTSEL,
+ GPIO55_nPREG,
+ GPIO56_nPWAIT,
+ GPIO57_nIOIS16,
+
+ /* MMC */
+ GPIO6_MMC_CLK,
+ GPIO8_MMC_CS0,
+
+ /* wakeup */
+ GPIO1_GPIO | WAKEUP_ON_EDGE_RISE,
+};
-
+#define LUB_HEXLED __LUB_REG(LUBBOCK_FPGA_PHYS + 0x010)
#define LUB_MISC_WR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x080)
+void lubbock_set_hexled(uint32_t value)
+{
+ LUB_HEXLED = value;
+}
+
void lubbock_set_misc_wr(unsigned int mask, unsigned int set)
{
unsigned long flags;
LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
}
-static struct irqchip lubbock_irq_chip = {
+static struct irq_chip lubbock_irq_chip = {
+ .name = "FPGA",
.ack = lubbock_mask_irq,
.mask = lubbock_mask_irq,
.unmask = lubbock_unmask_irq,
};
-static void lubbock_irq_handler(unsigned int irq, struct irqdesc *desc,
- struct pt_regs *regs)
+static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
{
unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
do {
GEDR(0) = GPIO_bit(0); /* clear our parent irq */
if (likely(pending)) {
irq = LUBBOCK_IRQ(0) + __ffs(pending);
- desc = irq_desc + irq;
- desc_handle_irq(irq, desc, regs);
+ generic_handle_irq(irq);
}
pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
} while (pending);
{
int irq;
- pxa_init_irq();
+ pxa25x_init_irq();
/* setup extra lubbock irqs */
for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) {
set_irq_chip(irq, &lubbock_irq_chip);
- set_irq_handler(irq, do_level_IRQ);
+ set_irq_handler(irq, handle_level_irq);
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
set_irq_chained_handler(IRQ_GPIO(0), lubbock_irq_handler);
- set_irq_type(IRQ_GPIO(0), IRQT_FALLING);
+ set_irq_type(IRQ_GPIO(0), IRQ_TYPE_EDGE_FALLING);
}
#ifdef CONFIG_PM
}
static struct sysdev_class lubbock_irq_sysclass = {
- set_kset_name("cpld_irq"),
+ .name = "cpld_irq",
.resume = lubbock_irq_resume,
};
static int __init lubbock_irq_device_init(void)
{
- int ret = sysdev_class_register(&lubbock_irq_sysclass);
- if (ret == 0)
- ret = sysdev_register(&lubbock_irq_device);
+ int ret = -ENODEV;
+
+ if (machine_is_lubbock()) {
+ ret = sysdev_class_register(&lubbock_irq_sysclass);
+ if (ret == 0)
+ ret = sysdev_register(&lubbock_irq_device);
+ }
return ret;
}
// no D+ pullup; lubbock can't connect/disconnect in software
};
-static struct platform_device lub_audio_device = {
- .name = "pxa2xx-ac97",
- .id = -1,
-};
-
static struct resource sa1111_resources[] = {
[0] = {
.start = 0x10000000,
.resource = sa1111_resources,
};
+/* ADS7846 is connected through SSP ... and if your board has J5 populated,
+ * you can select it to replace the ucb1400 by switching the touchscreen cable
+ * (to J5) and poking board registers (as done below). Else it's only useful
+ * for the temperature sensors.
+ */
+static struct pxa2xx_spi_master pxa_ssp_master_info = {
+ .num_chipselect = 1,
+};
+
+static int lubbock_ads7846_pendown_state(void)
+{
+ /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */
+ return 0;
+}
+
+static struct ads7846_platform_data ads_info = {
+ .model = 7846,
+ .vref_delay_usecs = 100, /* internal, no cap */
+ .get_pendown_state = lubbock_ads7846_pendown_state,
+ // .x_plate_ohms = 500, /* GUESS! */
+ // .y_plate_ohms = 500, /* GUESS! */
+};
+
+static void ads7846_cs(u32 command)
+{
+ static const unsigned TS_nCS = 1 << 11;
+ lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
+}
+
+static struct pxa2xx_spi_chip ads_hw = {
+ .tx_threshold = 1,
+ .rx_threshold = 2,
+ .cs_control = ads7846_cs,
+};
+
+static struct spi_board_info spi_board_info[] __initdata = { {
+ .modalias = "ads7846",
+ .platform_data = &ads_info,
+ .controller_data = &ads_hw,
+ .irq = LUBBOCK_BB_IRQ,
+ .max_speed_hz = 120000 /* max sample rate at 3V */
+ * 26 /* command + data + overhead */,
+ .bus_num = 1,
+ .chip_select = 0,
+},
+};
+
static struct resource smc91x_resources[] = {
[0] = {
.name = "smc91x-regs",
[1] = {
.start = LUBBOCK_ETH_IRQ,
.end = LUBBOCK_ETH_IRQ,
- .flags = IORESOURCE_IRQ,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
[2] = {
.name = "smc91x-attrib",
},
};
+static struct smc91x_platdata lubbock_smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_2,
+};
+
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = -1,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
+ .dev = {
+ .platform_data = &lubbock_smc91x_info,
+ },
};
static struct resource flash_resources[] = {
static struct platform_device *devices[] __initdata = {
&sa1111_device,
- &lub_audio_device,
&smc91x_device,
&lubbock_flash_device[0],
&lubbock_flash_device[1],
};
-static struct pxafb_mach_info sharp_lm8v31 __initdata = {
+static struct pxafb_mode_info sharp_lm8v31_mode = {
.pixclock = 270000,
.xres = 640,
.yres = 480,
.lower_margin = 0,
.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
.cmap_greyscale = 0,
+};
+
+static struct pxafb_mach_info sharp_lm8v31 = {
+ .modes = &sharp_lm8v31_mode,
+ .num_modes = 1,
.cmap_inverse = 0,
.cmap_static = 0,
- .lccr0 = LCCR0_SDS,
- .lccr3 = LCCR3_PCP | LCCR3_Acb(255),
+ .lcd_conn = LCD_COLOR_DSTN_16BPP | LCD_PCLK_EDGE_FALL |
+ LCD_AC_BIAS_FREQ(255),
};
#define MMC_POLL_RATE msecs_to_jiffies(1000)
static void lubbock_mmc_poll(unsigned long);
-static irqreturn_t (*mmc_detect_int)(int, void *, struct pt_regs *);
+static irq_handler_t mmc_detect_int;
static struct timer_list mmc_timer = {
.function = lubbock_mmc_poll,
if (LUB_IRQ_SET_CLR & (1 << 0))
mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
else {
- (void) mmc_detect_int(LUBBOCK_SD_IRQ, (void *)data, NULL);
+ (void) mmc_detect_int(LUBBOCK_SD_IRQ, (void *)data);
enable_irq(LUBBOCK_SD_IRQ);
}
}
-static irqreturn_t lubbock_detect_int(int irq, void *data, struct pt_regs *regs)
+static irqreturn_t lubbock_detect_int(int irq, void *data)
{
/* IRQ is level triggered; disable, and poll for removal */
disable_irq(irq);
mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
- return mmc_detect_int(irq, data, regs);
+ return mmc_detect_int(irq, data);
}
static int lubbock_mci_init(struct device *dev,
- irqreturn_t (*detect_int)(int, void *, struct pt_regs *),
+ irq_handler_t detect_int,
void *data)
{
- /* setup GPIO for PXA25x MMC controller */
- pxa_gpio_mode(GPIO6_MMCCLK_MD);
- pxa_gpio_mode(GPIO8_MMCCS0_MD);
-
/* detect card insert/eject */
mmc_detect_int = detect_int;
init_timer(&mmc_timer);
mmc_timer.data = (unsigned long) data;
return request_irq(LUBBOCK_SD_IRQ, lubbock_detect_int,
- SA_SAMPLE_RANDOM, "lubbock-sd-detect", data);
+ IRQF_SAMPLE_RANDOM, "lubbock-sd-detect", data);
}
static int lubbock_mci_get_ro(struct device *dev)
} else if (mode & IR_FIRMODE) {
LUB_MISC_WR |= 1 << 4;
}
+ pxa2xx_transceiver_mode(dev, mode);
local_irq_restore(flags);
}
{
int flashboot = (LUB_CONF_SWITCHES & 1);
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(lubbock_pin_config));
+
+ clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL);
pxa_set_udc_info(&udc_info);
set_pxa_fb_info(&sharp_lm8v31);
pxa_set_mci_info(&lubbock_mci_platform_data);
pxa_set_ficp_info(&lubbock_ficp_platform_data);
+ pxa_set_ac97_info(NULL);
lubbock_flash_data[0].width = lubbock_flash_data[1].width =
(BOOT_DEF & 1) ? 2 : 4;
lubbock_flash_data[flashboot^1].name = "application-flash";
lubbock_flash_data[flashboot].name = "boot-rom";
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ pxa2xx_set_spi_info(1, &pxa_ssp_master_info);
+ spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
}
static struct map_desc lubbock_io_desc[] __initdata = {
pxa_map_io();
iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc));
- /* This enables the BTUART */
- pxa_gpio_mode(GPIO42_BTRXD_MD);
- pxa_gpio_mode(GPIO43_BTTXD_MD);
- pxa_gpio_mode(GPIO44_BTCTS_MD);
- pxa_gpio_mode(GPIO45_BTRTS_MD);
-
- /* This is for the SMC chip select */
- pxa_gpio_mode(GPIO79_nCS_3_MD);
-
- /* setup sleep mode values */
- PWER = 0x00000002;
- PFER = 0x00000000;
- PRER = 0x00000002;
- PGSR0 = 0x00008000;
- PGSR1 = 0x003F0202;
- PGSR2 = 0x0001C000;
PCFR |= PCFR_OPDE;
}
MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)")
/* Maintainer: MontaVista Software Inc. */
- .phys_ram = 0xa0000000,
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
.map_io = lubbock_map_io,