#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/input.h>
+#include <linux/gpio_keys.h>
#include <linux/workqueue.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
+#include <linux/regulator/machine.h>
#include <linux/i2c/twl4030.h>
+#include <linux/io.h>
+#include <linux/smsc911x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/board-ldp.h>
-#include <mach/mcspi.h>
+#include <plat/mcspi.h>
#include <mach/gpio.h>
-#include <mach/board.h>
-#include <mach/common.h>
-#include <mach/gpmc.h>
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/gpmc.h>
-#include <asm/io.h>
#include <asm/delay.h>
-#include <mach/control.h>
+#include <plat/control.h>
+#include <plat/usb.h>
+#include <plat/keypad.h>
#include "mmc-twl4030.h"
-#define SDP3430_SMC91X_CS 3
+#define LDP_SMSC911X_CS 1
+#define LDP_SMSC911X_GPIO 152
+#define DEBUG_BASE 0x08000000
+#define LDP_ETHR_START DEBUG_BASE
-static struct resource ldp_smc911x_resources[] = {
+static struct resource ldp_smsc911x_resources[] = {
[0] = {
- .start = OMAP34XX_ETHR_START,
- .end = OMAP34XX_ETHR_START + SZ_4K,
+ .start = LDP_ETHR_START,
+ .end = LDP_ETHR_START + SZ_4K,
.flags = IORESOURCE_MEM,
},
[1] = {
},
};
-static struct platform_device ldp_smc911x_device = {
- .name = "smc911x",
+static struct smsc911x_platform_config ldp_smsc911x_config = {
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .flags = SMSC911X_USE_32BIT,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+static struct platform_device ldp_smsc911x_device = {
+ .name = "smsc911x",
.id = -1,
- .num_resources = ARRAY_SIZE(ldp_smc911x_resources),
- .resource = ldp_smc911x_resources,
+ .num_resources = ARRAY_SIZE(ldp_smsc911x_resources),
+ .resource = ldp_smsc911x_resources,
+ .dev = {
+ .platform_data = &ldp_smsc911x_config,
+ },
};
-static struct platform_device *ldp_devices[] __initdata = {
- &ldp_smc911x_device,
+static int board_keymap[] = {
+ KEY(0, 0, KEY_1),
+ KEY(1, 0, KEY_2),
+ KEY(2, 0, KEY_3),
+ KEY(0, 1, KEY_4),
+ KEY(1, 1, KEY_5),
+ KEY(2, 1, KEY_6),
+ KEY(3, 1, KEY_F5),
+ KEY(0, 2, KEY_7),
+ KEY(1, 2, KEY_8),
+ KEY(2, 2, KEY_9),
+ KEY(3, 2, KEY_F6),
+ KEY(0, 3, KEY_F7),
+ KEY(1, 3, KEY_0),
+ KEY(2, 3, KEY_F8),
+ PERSISTENT_KEY(4, 5),
+ KEY(4, 4, KEY_VOLUMEUP),
+ KEY(5, 5, KEY_VOLUMEDOWN),
+ 0
+};
+
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
+static struct twl4030_keypad_data ldp_kp_twl4030_data = {
+ .keymap_data = &board_map_data,
+ .rows = 6,
+ .cols = 6,
+ .rep = 1,
};
-static inline void __init ldp_init_smc911x(void)
+static struct gpio_keys_button ldp_gpio_keys_buttons[] = {
+ [0] = {
+ .code = KEY_ENTER,
+ .gpio = 101,
+ .desc = "enter sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [1] = {
+ .code = KEY_F1,
+ .gpio = 102,
+ .desc = "func 1",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [2] = {
+ .code = KEY_F2,
+ .gpio = 103,
+ .desc = "func 2",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [3] = {
+ .code = KEY_F3,
+ .gpio = 104,
+ .desc = "func 3",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [4] = {
+ .code = KEY_F4,
+ .gpio = 105,
+ .desc = "func 4",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [5] = {
+ .code = KEY_LEFT,
+ .gpio = 106,
+ .desc = "left sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [6] = {
+ .code = KEY_RIGHT,
+ .gpio = 107,
+ .desc = "right sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [7] = {
+ .code = KEY_UP,
+ .gpio = 108,
+ .desc = "up sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [8] = {
+ .code = KEY_DOWN,
+ .gpio = 109,
+ .desc = "down sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+};
+
+static struct gpio_keys_platform_data ldp_gpio_keys = {
+ .buttons = ldp_gpio_keys_buttons,
+ .nbuttons = ARRAY_SIZE(ldp_gpio_keys_buttons),
+ .rep = 1,
+};
+
+static struct platform_device ldp_gpio_keys_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &ldp_gpio_keys,
+ },
+};
+
+static int ts_gpio;
+
+/**
+ * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
+ *
+ * @return - void. If request gpio fails then Flag KERN_ERR.
+ */
+static void ads7846_dev_init(void)
+{
+ if (gpio_request(ts_gpio, "ads7846 irq") < 0) {
+ printk(KERN_ERR "can't get ads746 pen down GPIO\n");
+ return;
+ }
+
+ gpio_direction_input(ts_gpio);
+ omap_set_gpio_debounce(ts_gpio, 1);
+ omap_set_gpio_debounce_time(ts_gpio, 0xa);
+}
+
+static int ads7846_get_pendown_state(void)
+{
+ return !gpio_get_value(ts_gpio);
+}
+
+static struct ads7846_platform_data tsc2046_config __initdata = {
+ .get_pendown_state = ads7846_get_pendown_state,
+ .keep_vref_on = 1,
+};
+
+static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+static struct spi_board_info ldp_spi_board_info[] __initdata = {
+ [0] = {
+ /*
+ * TSC2046 operates at a max freqency of 2MHz, so
+ * operate slightly below at 1.5MHz
+ */
+ .modalias = "ads7846",
+ .bus_num = 1,
+ .chip_select = 0,
+ .max_speed_hz = 1500000,
+ .controller_data = &tsc2046_mcspi_config,
+ .irq = 0,
+ .platform_data = &tsc2046_config,
+ },
+};
+
+static inline void __init ldp_init_smsc911x(void)
{
int eth_cs;
unsigned long cs_mem_base;
int eth_gpio = 0;
- eth_cs = LDP_SMC911X_CS;
+ eth_cs = LDP_SMSC911X_CS;
if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
- printk(KERN_ERR "Failed to request GPMC mem for smc911x\n");
+ printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n");
return;
}
- ldp_smc911x_resources[0].start = cs_mem_base + 0x0;
- ldp_smc911x_resources[0].end = cs_mem_base + 0xf;
+ ldp_smsc911x_resources[0].start = cs_mem_base + 0x0;
+ ldp_smsc911x_resources[0].end = cs_mem_base + 0xff;
udelay(100);
- eth_gpio = LDP_SMC911X_GPIO;
+ eth_gpio = LDP_SMSC911X_GPIO;
- ldp_smc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
+ ldp_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
- if (gpio_request(eth_gpio, "smc911x irq") < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for smc911x IRQ\n",
+ if (gpio_request(eth_gpio, "smsc911x irq") < 0) {
+ printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
eth_gpio);
return;
}
gpio_direction_input(eth_gpio);
}
+static struct platform_device ldp_lcd_device = {
+ .name = "ldp_lcd",
+ .id = -1,
+};
+
+static struct omap_lcd_config ldp_lcd_config __initdata = {
+ .ctrl_name = "internal",
+};
+
+static struct omap_board_config_kernel ldp_config[] __initdata = {
+ { OMAP_TAG_LCD, &ldp_lcd_config },
+};
+
static void __init omap_ldp_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap_board_config = ldp_config;
+ omap_board_config_size = ARRAY_SIZE(ldp_config);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
- ldp_init_smc911x();
+ ldp_init_smsc911x();
}
-static struct omap_uart_config ldp_uart_config __initdata = {
- .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
-static struct omap_board_config_kernel ldp_config[] __initdata = {
- { OMAP_TAG_UART, &ldp_uart_config },
+static struct twl4030_usb_data ldp_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
};
static struct twl4030_gpio_platform_data ldp_gpio_data = {
.irq_end = TWL4030_GPIO_IRQ_END,
};
+static struct twl4030_madc_platform_data ldp_madc_data = {
+ .irq_line = 1,
+};
+
+static struct regulator_consumer_supply ldp_vmmc1_supply = {
+ .supply = "vmmc",
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data ldp_vmmc1 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &ldp_vmmc1_supply,
+};
+
static struct twl4030_platform_data ldp_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
+ .madc = &ldp_madc_data,
+ .usb = &ldp_usb_data,
+ .vmmc1 = &ldp_vmmc1,
.gpio = &ldp_gpio_data,
+ .keypad = &ldp_kp_twl4030_data,
};
static struct i2c_board_info __initdata ldp_i2c_boardinfo[] = {
{} /* Terminator */
};
+static struct platform_device *ldp_devices[] __initdata = {
+ &ldp_smsc911x_device,
+ &ldp_lcd_device,
+ &ldp_gpio_keys_device,
+};
+
static void __init omap_ldp_init(void)
{
omap_i2c_init();
platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
- omap_board_config = ldp_config;
- omap_board_config_size = ARRAY_SIZE(ldp_config);
+ ts_gpio = 54;
+ ldp_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
+ spi_register_board_info(ldp_spi_board_info,
+ ARRAY_SIZE(ldp_spi_board_info));
+ ads7846_dev_init();
omap_serial_init();
+ usb_musb_init();
+
twl4030_mmc_init(mmc);
+ /* link regulators to MMC adapters */
+ ldp_vmmc1_supply.dev = mmc[0].dev;
}
static void __init omap_ldp_map_io(void)
MACHINE_START(OMAP_LDP, "OMAP LDP board")
.phys_io = 0x48000000,
- .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc,
.boot_params = 0x80000100,
.map_io = omap_ldp_map_io,
.init_irq = omap_ldp_init_irq,
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff