* MA 02110-1301, USA.
*/
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+#include <linux/io.h>
#include <linux/mtd/plat-ram.h>
-#include <asm/mach/arch.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/mc13783.h>
+#include <linux/spi/spi.h>
+#include <linux/irq.h>
+
#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include <mach/board-pcm038.h>
#include <mach/common.h>
#include <mach/hardware.h>
-#include <mach/iomux-mx1-mx2.h>
-#include <asm/mach/time.h>
+#include <mach/i2c.h>
+#include <mach/iomux.h>
#include <mach/imx-uart.h>
-#include <mach/board-pcm038.h>
+#include <mach/mxc_nand.h>
+#include <mach/spi.h>
#include "devices.h"
+static int pcm038_pins[] = {
+ /* UART1 */
+ PE12_PF_UART1_TXD,
+ PE13_PF_UART1_RXD,
+ PE14_PF_UART1_CTS,
+ PE15_PF_UART1_RTS,
+ /* UART2 */
+ PE3_PF_UART2_CTS,
+ PE4_PF_UART2_RTS,
+ PE6_PF_UART2_TXD,
+ PE7_PF_UART2_RXD,
+ /* UART3 */
+ PE8_PF_UART3_TXD,
+ PE9_PF_UART3_RXD,
+ PE10_PF_UART3_CTS,
+ PE11_PF_UART3_RTS,
+ /* FEC */
+ PD0_AIN_FEC_TXD0,
+ PD1_AIN_FEC_TXD1,
+ PD2_AIN_FEC_TXD2,
+ PD3_AIN_FEC_TXD3,
+ PD4_AOUT_FEC_RX_ER,
+ PD5_AOUT_FEC_RXD1,
+ PD6_AOUT_FEC_RXD2,
+ PD7_AOUT_FEC_RXD3,
+ PD8_AF_FEC_MDIO,
+ PD9_AIN_FEC_MDC,
+ PD10_AOUT_FEC_CRS,
+ PD11_AOUT_FEC_TX_CLK,
+ PD12_AOUT_FEC_RXD0,
+ PD13_AOUT_FEC_RX_DV,
+ PD14_AOUT_FEC_RX_CLK,
+ PD15_AOUT_FEC_COL,
+ PD16_AIN_FEC_TX_ER,
+ PF23_AIN_FEC_TX_EN,
+ /* I2C2 */
+ PC5_PF_I2C2_SDA,
+ PC6_PF_I2C2_SCL,
+ /* SPI1 */
+ PD25_PF_CSPI1_RDY,
+ PD29_PF_CSPI1_SCLK,
+ PD30_PF_CSPI1_MISO,
+ PD31_PF_CSPI1_MOSI,
+ /* SSI1 */
+ PC20_PF_SSI1_FS,
+ PC21_PF_SSI1_RXD,
+ PC22_PF_SSI1_TXD,
+ PC23_PF_SSI1_CLK,
+ /* SSI4 */
+ PC16_PF_SSI4_FS,
+ PC17_PF_SSI4_RXD,
+ PC18_PF_SSI4_TXD,
+ PC19_PF_SSI4_CLK,
+};
+
/*
* Phytec's PCM038 comes with 2MiB battery buffered SRAM,
* 16 bit width
.resource = &pcm038_flash_resource,
};
-static int mxc_uart0_pins[] = {
- PE12_PF_UART1_TXD,
- PE13_PF_UART1_RXD,
- PE14_PF_UART1_CTS,
- PE15_PF_UART1_RTS
-};
-
-static int uart_mxc_port0_init(struct platform_device *pdev)
-{
- return mxc_gpio_setup_multiple_pins(mxc_uart0_pins,
- ARRAY_SIZE(mxc_uart0_pins), "UART0");
-}
-
-static int uart_mxc_port0_exit(struct platform_device *pdev)
-{
- mxc_gpio_release_multiple_pins(mxc_uart0_pins,
- ARRAY_SIZE(mxc_uart0_pins));
- return 0;
-}
-
-static int mxc_uart1_pins[] = {
- PE3_PF_UART2_CTS,
- PE4_PF_UART2_RTS,
- PE6_PF_UART2_TXD,
- PE7_PF_UART2_RXD
-};
-
-static int uart_mxc_port1_init(struct platform_device *pdev)
-{
- return mxc_gpio_setup_multiple_pins(mxc_uart1_pins,
- ARRAY_SIZE(mxc_uart1_pins), "UART1");
-}
-
-static int uart_mxc_port1_exit(struct platform_device *pdev)
-{
- mxc_gpio_release_multiple_pins(mxc_uart1_pins,
- ARRAY_SIZE(mxc_uart1_pins));
- return 0;
-}
-
-static int mxc_uart2_pins[] = { PE10_PF_UART3_CTS,
- PE9_PF_UART3_RXD,
- PE10_PF_UART3_CTS,
- PE9_PF_UART3_RXD };
-
-static int uart_mxc_port2_init(struct platform_device *pdev)
-{
- return mxc_gpio_setup_multiple_pins(mxc_uart2_pins,
- ARRAY_SIZE(mxc_uart2_pins), "UART2");
-}
-
-static int uart_mxc_port2_exit(struct platform_device *pdev)
-{
- mxc_gpio_release_multiple_pins(mxc_uart2_pins,
- ARRAY_SIZE(mxc_uart2_pins));
- return 0;
-}
-
static struct imxuart_platform_data uart_pdata[] = {
{
- .init = uart_mxc_port0_init,
- .exit = uart_mxc_port0_exit,
.flags = IMXUART_HAVE_RTSCTS,
}, {
- .init = uart_mxc_port1_init,
- .exit = uart_mxc_port1_exit,
.flags = IMXUART_HAVE_RTSCTS,
}, {
- .init = uart_mxc_port2_init,
- .exit = uart_mxc_port2_exit,
.flags = IMXUART_HAVE_RTSCTS,
},
};
-static int mxc_fec_pins[] = {
- PD0_AIN_FEC_TXD0,
- PD1_AIN_FEC_TXD1,
- PD2_AIN_FEC_TXD2,
- PD3_AIN_FEC_TXD3,
- PD4_AOUT_FEC_RX_ER,
- PD5_AOUT_FEC_RXD1,
- PD6_AOUT_FEC_RXD2,
- PD7_AOUT_FEC_RXD3,
- PD8_AF_FEC_MDIO,
- PD9_AIN_FEC_MDC,
- PD10_AOUT_FEC_CRS,
- PD11_AOUT_FEC_TX_CLK,
- PD12_AOUT_FEC_RXD0,
- PD13_AOUT_FEC_RX_DV,
- PD14_AOUT_FEC_CLR,
- PD15_AOUT_FEC_COL,
- PD16_AIN_FEC_TX_ER,
- PF23_AIN_FEC_TX_EN
+static struct mxc_nand_platform_data pcm038_nand_board_info = {
+ .width = 1,
+ .hw_ecc = 1,
};
-static void gpio_fec_active(void)
-{
- mxc_gpio_setup_multiple_pins(mxc_fec_pins,
- ARRAY_SIZE(mxc_fec_pins), "FEC");
-}
-
-static void gpio_fec_inactive(void)
-{
- mxc_gpio_release_multiple_pins(mxc_fec_pins,
- ARRAY_SIZE(mxc_fec_pins));
-}
-
static struct platform_device *platform_devices[] __initdata = {
&pcm038_nor_mtd_device,
&mxc_w1_master_device,
+ &mxc_fec_device,
&pcm038_sram_mtd_device,
};
__raw_writel(0x22220a00, CSCR_A(1));
}
+static struct imxi2c_platform_data pcm038_i2c_1_data = {
+ .bitrate = 100000,
+};
+
+static struct at24_platform_data board_eeprom = {
+ .byte_len = 4096,
+ .page_size = 32,
+ .flags = AT24_FLAG_ADDR16,
+};
+
+static struct i2c_board_info pcm038_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */
+ .platform_data = &board_eeprom,
+ }, {
+ I2C_BOARD_INFO("pcf8563", 0x51),
+ }, {
+ I2C_BOARD_INFO("lm75", 0x4a),
+ }
+};
+
+static int pcm038_spi_cs[] = {GPIO_PORTD + 28};
+
+static struct spi_imx_master pcm038_spi_0_data = {
+ .chipselect = pcm038_spi_cs,
+ .num_chipselect = ARRAY_SIZE(pcm038_spi_cs),
+};
+
+static struct regulator_consumer_supply sdhc1_consumers[] = {
+ {
+ .dev = &mxc_sdhc_device1.dev,
+ .supply = "sdhc_vcc",
+ },
+};
+
+static struct regulator_init_data sdhc1_data = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3400000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL |
+ REGULATOR_MODE_FAST,
+ .always_on = 0,
+ .boot_on = 0,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(sdhc1_consumers),
+ .consumer_supplies = sdhc1_consumers,
+};
+
+static struct regulator_consumer_supply cam_consumers[] = {
+ {
+ .dev = NULL,
+ .supply = "imx_cam_vcc",
+ },
+};
+
+static struct regulator_init_data cam_data = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3400000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL |
+ REGULATOR_MODE_FAST,
+ .always_on = 0,
+ .boot_on = 0,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(cam_consumers),
+ .consumer_supplies = cam_consumers,
+};
+
+struct mc13783_regulator_init_data pcm038_regulators[] = {
+ {
+ .id = MC13783_REGU_VCAM,
+ .init_data = &cam_data,
+ }, {
+ .id = MC13783_REGU_VMMC1,
+ .init_data = &sdhc1_data,
+ },
+};
+
+static struct mc13783_platform_data pcm038_pmic = {
+ .regulators = pcm038_regulators,
+ .num_regulators = ARRAY_SIZE(pcm038_regulators),
+ .flags = MC13783_USE_ADC | MC13783_USE_REGULATOR |
+ MC13783_USE_TOUCHSCREEN,
+};
+
+static struct spi_board_info pcm038_spi_board_info[] __initdata = {
+ {
+ .modalias = "mc13783",
+ .irq = IRQ_GPIOB(23),
+ .max_speed_hz = 300000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .platform_data = &pcm038_pmic,
+ .mode = SPI_CS_HIGH,
+ }
+};
+
static void __init pcm038_init(void)
{
- gpio_fec_active();
+ mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins),
+ "PCM038");
+
pcm038_init_sram();
mxc_register_device(&mxc_uart_device0, &uart_pdata[0]);
mxc_register_device(&mxc_uart_device1, &uart_pdata[1]);
mxc_register_device(&mxc_uart_device2, &uart_pdata[2]);
- mxc_gpio_mode(PE16_AF_RTCK); /* OWIRE */
+
+ mxc_gpio_mode(PE16_AF_OWIRE);
+ mxc_register_device(&mxc_nand_device, &pcm038_nand_board_info);
+
+ /* only the i2c master 1 is used on this CPU card */
+ i2c_register_board_info(1, pcm038_i2c_devices,
+ ARRAY_SIZE(pcm038_i2c_devices));
+
+ mxc_register_device(&mxc_i2c_device1, &pcm038_i2c_1_data);
+
+ /* PE18 for user-LED D40 */
+ mxc_gpio_mode(GPIO_PORTE | 18 | GPIO_GPIO | GPIO_OUT);
+
+ mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
+
+ /* MC13783 IRQ */
+ mxc_gpio_mode(GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN);
+
+ mxc_register_device(&mxc_spi_device0, &pcm038_spi_0_data);
+ spi_register_board_info(pcm038_spi_board_info,
+ ARRAY_SIZE(pcm038_spi_board_info));
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
static void __init pcm038_timer_init(void)
{
- mxc_clocks_init(26000000);
- mxc_timer_init("gpt_clk.0");
+ mx27_clocks_init(26000000);
}
-struct sys_timer pcm038_timer = {
+static struct sys_timer pcm038_timer = {
.init = pcm038_timer_init,
};
.phys_io = AIPI_BASE_ADDR,
.io_pg_offst = ((AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc,
.boot_params = PHYS_OFFSET + 0x100,
- .map_io = mxc_map_io,
- .init_irq = mxc_init_irq,
+ .map_io = mx27_map_io,
+ .init_irq = mx27_init_irq,
.init_machine = pcm038_init,
.timer = &pcm038_timer,
MACHINE_END
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff