#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mv643xx_eth.h>
#include <linux/gpio.h>
+#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
#include <plat/mvsdio.h>
-#include <plat/orion_nand.h>
#include "common.h"
#include "mpp.h"
},
};
-static struct resource sheevaplug_nand_resource = {
- .flags = IORESOURCE_MEM,
- .start = KIRKWOOD_NAND_MEM_PHYS_BASE,
- .end = KIRKWOOD_NAND_MEM_PHYS_BASE +
- KIRKWOOD_NAND_MEM_SIZE - 1,
+static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(0),
};
-static struct orion_nand_data sheevaplug_nand_data = {
- .parts = sheevaplug_nand_parts,
- .nr_parts = ARRAY_SIZE(sheevaplug_nand_parts),
- .cle = 0,
- .ale = 1,
- .width = 8,
- .chip_delay = 25,
+static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
+ /* unfortunately the CD signal has not been connected */
};
-static struct platform_device sheevaplug_nand_flash = {
- .name = "orion_nand",
- .id = -1,
- .dev = {
- .platform_data = &sheevaplug_nand_data,
+static struct gpio_led sheevaplug_led_pins[] = {
+ {
+ .name = "plug:green:health",
+ .default_trigger = "default-on",
+ .gpio = 49,
+ .active_low = 1,
},
- .resource = &sheevaplug_nand_resource,
- .num_resources = 1,
};
-static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(0),
+static struct gpio_led_platform_data sheevaplug_led_data = {
+ .leds = sheevaplug_led_pins,
+ .num_leds = ARRAY_SIZE(sheevaplug_led_pins),
};
-static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
- // unfortunately the CD signal has not been connected */
+static struct platform_device sheevaplug_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &sheevaplug_led_data,
+ }
};
static unsigned int sheevaplug_mpp_config[] __initdata = {
MPP29_GPIO, /* USB Power Enable */
+ MPP49_GPIO, /* LED */
0
};
kirkwood_mpp_conf(sheevaplug_mpp_config);
kirkwood_uart0_init();
+ kirkwood_nand_init(ARRAY_AND_SIZE(sheevaplug_nand_parts), 25);
if (gpio_request(29, "USB Power Enable") != 0 ||
gpio_direction_output(29, 1) != 0)
kirkwood_ge00_init(&sheevaplug_ge00_data);
kirkwood_sdio_init(&sheevaplug_mvsdio_data);
- platform_device_register(&sheevaplug_nand_flash);
+ platform_device_register(&sheevaplug_leds);
}
MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")