#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
+#include <linux/platform_device.h>
#include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
#include <linux/dma-mapping.h>
-#include <linux/time.h>
#include <linux/timex.h>
-#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
#include <linux/termios.h>
#include <linux/amba/bus.h>
#include <linux/amba/serial.h>
-#include <linux/io.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
+#include <mach/fb.h>
+#include <mach/ep93xx_keypad.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
#include <asm/hardware/vic.h>
*/
static unsigned int last_jiffy_time;
-#define TIMER4_TICKS_PER_JIFFY ((CLOCK_TICK_RATE + (HZ/2)) / HZ)
+#define TIMER4_TICKS_PER_JIFFY DIV_ROUND_CLOSEST(CLOCK_TICK_RATE, HZ)
static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
{
for (i = 0; i < 8; i++) {
if (status & (1 << i)) {
int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_B(0)) + i;
- desc = irq_desc + gpio_irq;
generic_handle_irq(gpio_irq);
}
}
{
int gpio_irq;
- vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
- vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
+ vic_init(EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
+ vic_init(EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
for (gpio_irq = gpio_to_irq(0);
gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
*/
static DEFINE_SPINLOCK(syscon_swlock);
-void ep93xx_syscon_swlocked_write(unsigned int val, unsigned int reg)
+void ep93xx_syscon_swlocked_write(unsigned int val, void __iomem *reg)
{
unsigned long flags;
void __init ep93xx_register_eth(struct ep93xx_eth_data *data, int copy_addr)
{
- if (copy_addr) {
- memcpy(data->dev_addr,
- (void *)(EP93XX_ETHERNET_BASE + 0x50), 6);
- }
+ if (copy_addr)
+ memcpy_fromio(data->dev_addr, EP93XX_ETHERNET_BASE + 0x50, 6);
ep93xx_eth_data = *data;
platform_device_register(&ep93xx_eth_device);
}
-static struct i2c_gpio_platform_data ep93xx_i2c_data = {
- .sda_pin = EP93XX_GPIO_LINE_EEDAT,
- .sda_is_open_drain = 0,
- .scl_pin = EP93XX_GPIO_LINE_EECLK,
- .scl_is_open_drain = 0,
- .udelay = 2,
-};
+
+/*************************************************************************
+ * EP93xx i2c peripheral handling
+ *************************************************************************/
+static struct i2c_gpio_platform_data ep93xx_i2c_data;
static struct platform_device ep93xx_i2c_device = {
.name = "i2c-gpio",
.dev.platform_data = &ep93xx_i2c_data,
};
-void __init ep93xx_register_i2c(struct i2c_board_info *devices, int num)
+void __init ep93xx_register_i2c(struct i2c_gpio_platform_data *data,
+ struct i2c_board_info *devices, int num)
{
+ /*
+ * Set the EEPROM interface pin drive type control.
+ * Defines the driver type for the EECLK and EEDAT pins as either
+ * open drain, which will require an external pull-up, or a normal
+ * CMOS driver.
+ */
+ if (data->sda_is_open_drain && data->sda_pin != EP93XX_GPIO_LINE_EEDAT)
+ pr_warning("ep93xx: sda != EEDAT, open drain has no effect\n");
+ if (data->scl_is_open_drain && data->scl_pin != EP93XX_GPIO_LINE_EECLK)
+ pr_warning("ep93xx: scl != EECLK, open drain has no effect\n");
+
+ __raw_writel((data->sda_is_open_drain << 1) |
+ (data->scl_is_open_drain << 0),
+ EP93XX_GPIO_EEDRIVE);
+
+ ep93xx_i2c_data = *data;
i2c_register_board_info(0, devices, num);
platform_device_register(&ep93xx_i2c_device);
}
+
+/*************************************************************************
+ * EP93xx LEDs
+ *************************************************************************/
+static struct gpio_led ep93xx_led_pins[] = {
+ {
+ .name = "platform:grled",
+ .gpio = EP93XX_GPIO_LINE_GRLED,
+ }, {
+ .name = "platform:rdled",
+ .gpio = EP93XX_GPIO_LINE_RDLED,
+ },
+};
+
+static struct gpio_led_platform_data ep93xx_led_data = {
+ .num_leds = ARRAY_SIZE(ep93xx_led_pins),
+ .leds = ep93xx_led_pins,
+};
+
+static struct platform_device ep93xx_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &ep93xx_led_data,
+ },
+};
+
+
+/*************************************************************************
+ * EP93xx pwm peripheral handling
+ *************************************************************************/
+static struct resource ep93xx_pwm0_resource[] = {
+ {
+ .start = EP93XX_PWM_PHYS_BASE,
+ .end = EP93XX_PWM_PHYS_BASE + 0x10 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device ep93xx_pwm0_device = {
+ .name = "ep93xx-pwm",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(ep93xx_pwm0_resource),
+ .resource = ep93xx_pwm0_resource,
+};
+
+static struct resource ep93xx_pwm1_resource[] = {
+ {
+ .start = EP93XX_PWM_PHYS_BASE + 0x20,
+ .end = EP93XX_PWM_PHYS_BASE + 0x30 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device ep93xx_pwm1_device = {
+ .name = "ep93xx-pwm",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(ep93xx_pwm1_resource),
+ .resource = ep93xx_pwm1_resource,
+};
+
+void __init ep93xx_register_pwm(int pwm0, int pwm1)
+{
+ if (pwm0)
+ platform_device_register(&ep93xx_pwm0_device);
+
+ /* NOTE: EP9307 does not have PWMOUT1 (pin EGPIO14) */
+ if (pwm1)
+ platform_device_register(&ep93xx_pwm1_device);
+}
+
+int ep93xx_pwm_acquire_gpio(struct platform_device *pdev)
+{
+ int err;
+
+ if (pdev->id == 0) {
+ err = 0;
+ } else if (pdev->id == 1) {
+ err = gpio_request(EP93XX_GPIO_LINE_EGPIO14,
+ dev_name(&pdev->dev));
+ if (err)
+ return err;
+ err = gpio_direction_output(EP93XX_GPIO_LINE_EGPIO14, 0);
+ if (err)
+ goto fail;
+
+ /* PWM 1 output on EGPIO[14] */
+ ep93xx_devcfg_set_bits(EP93XX_SYSCON_DEVCFG_PONG);
+ } else {
+ err = -ENODEV;
+ }
+
+ return err;
+
+fail:
+ gpio_free(EP93XX_GPIO_LINE_EGPIO14);
+ return err;
+}
+EXPORT_SYMBOL(ep93xx_pwm_acquire_gpio);
+
+void ep93xx_pwm_release_gpio(struct platform_device *pdev)
+{
+ if (pdev->id == 1) {
+ gpio_direction_input(EP93XX_GPIO_LINE_EGPIO14);
+ gpio_free(EP93XX_GPIO_LINE_EGPIO14);
+
+ /* EGPIO[14] used for GPIO */
+ ep93xx_devcfg_clear_bits(EP93XX_SYSCON_DEVCFG_PONG);
+ }
+}
+EXPORT_SYMBOL(ep93xx_pwm_release_gpio);
+
+
+/*************************************************************************
+ * EP93xx video peripheral handling
+ *************************************************************************/
+static struct ep93xxfb_mach_info ep93xxfb_data;
+
+static struct resource ep93xx_fb_resource[] = {
+ {
+ .start = EP93XX_RASTER_PHYS_BASE,
+ .end = EP93XX_RASTER_PHYS_BASE + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device ep93xx_fb_device = {
+ .name = "ep93xx-fb",
+ .id = -1,
+ .dev = {
+ .platform_data = &ep93xxfb_data,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .dma_mask = &ep93xx_fb_device.dev.coherent_dma_mask,
+ },
+ .num_resources = ARRAY_SIZE(ep93xx_fb_resource),
+ .resource = ep93xx_fb_resource,
+};
+
+void __init ep93xx_register_fb(struct ep93xxfb_mach_info *data)
+{
+ ep93xxfb_data = *data;
+ platform_device_register(&ep93xx_fb_device);
+}
+
+
+/*************************************************************************
+ * EP93xx matrix keypad peripheral handling
+ *************************************************************************/
+static struct resource ep93xx_keypad_resource[] = {
+ {
+ .start = EP93XX_KEY_MATRIX_PHYS_BASE,
+ .end = EP93XX_KEY_MATRIX_PHYS_BASE + 0x0c - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_EP93XX_KEY,
+ .end = IRQ_EP93XX_KEY,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device ep93xx_keypad_device = {
+ .name = "ep93xx-keypad",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(ep93xx_keypad_resource),
+ .resource = ep93xx_keypad_resource,
+};
+
+void __init ep93xx_register_keypad(struct ep93xx_keypad_platform_data *data)
+{
+ ep93xx_keypad_device.dev.platform_data = data;
+ platform_device_register(&ep93xx_keypad_device);
+}
+
+int ep93xx_keypad_acquire_gpio(struct platform_device *pdev)
+{
+ int err;
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ err = gpio_request(EP93XX_GPIO_LINE_C(i), dev_name(&pdev->dev));
+ if (err)
+ goto fail_gpio_c;
+ err = gpio_request(EP93XX_GPIO_LINE_D(i), dev_name(&pdev->dev));
+ if (err)
+ goto fail_gpio_d;
+ }
+
+ /* Enable the keypad controller; GPIO ports C and D used for keypad */
+ ep93xx_devcfg_clear_bits(EP93XX_SYSCON_DEVCFG_KEYS |
+ EP93XX_SYSCON_DEVCFG_GONK);
+
+ return 0;
+
+fail_gpio_d:
+ gpio_free(EP93XX_GPIO_LINE_C(i));
+fail_gpio_c:
+ for ( ; i >= 0; --i) {
+ gpio_free(EP93XX_GPIO_LINE_C(i));
+ gpio_free(EP93XX_GPIO_LINE_D(i));
+ }
+ return err;
+}
+EXPORT_SYMBOL(ep93xx_keypad_acquire_gpio);
+
+void ep93xx_keypad_release_gpio(struct platform_device *pdev)
+{
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ gpio_free(EP93XX_GPIO_LINE_C(i));
+ gpio_free(EP93XX_GPIO_LINE_D(i));
+ }
+
+ /* Disable the keypad controller; GPIO ports C and D used for GPIO */
+ ep93xx_devcfg_set_bits(EP93XX_SYSCON_DEVCFG_KEYS |
+ EP93XX_SYSCON_DEVCFG_GONK);
+}
+EXPORT_SYMBOL(ep93xx_keypad_release_gpio);
+
+
extern void ep93xx_gpio_init(void);
void __init ep93xx_init_devices(void)
platform_device_register(&ep93xx_rtc_device);
platform_device_register(&ep93xx_ohci_device);
+ platform_device_register(&ep93xx_leds);
}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff