* or implied.
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/interrupt.h>
#include <linux/gpio.h>
+#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/i2c/pcf857x.h>
#include <linux/i2c/at24.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <mach/common.h>
-#include <mach/irqs.h>
#include <mach/cp_intc.h>
#include <mach/mux.h>
-#include <mach/gpio.h>
+#include <mach/nand.h>
#include <mach/da8xx.h>
-#include <mach/asp.h>
#include <mach/usb.h>
#define DA830_EVM_PHY_MASK 0x0
#define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
-static struct at24_platform_data da830_evm_i2c_eeprom_info = {
- .byte_len = SZ_256K / 8,
- .page_size = 64,
- .flags = AT24_FLAG_ADDR16,
- .setup = davinci_get_mac_addr,
- .context = (void *)0x7f00,
-};
-
-static int da830_evm_ui_expander_setup(struct i2c_client *client, int gpio,
- unsigned ngpio, void *context)
-{
- gpio_request(gpio + 6, "MUX_MODE");
-#ifdef CONFIG_DA830_UI_LCD
- gpio_direction_output(gpio + 6, 0);
-#else /* Must be NAND or NOR */
- gpio_direction_output(gpio + 6, 1);
-#endif
- return 0;
-}
-
-static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
- unsigned ngpio, void *context)
-{
- gpio_free(gpio + 6);
- return 0;
-}
-
-static struct pcf857x_platform_data da830_evm_ui_expander_info = {
- .gpio_base = DAVINCI_N_GPIO,
- .setup = da830_evm_ui_expander_setup,
- .teardown = da830_evm_ui_expander_teardown,
-};
-
-static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c256", 0x50),
- .platform_data = &da830_evm_i2c_eeprom_info,
- },
- {
- I2C_BOARD_INFO("tlv320aic3x", 0x18),
- },
- {
- I2C_BOARD_INFO("pcf8574", 0x3f),
- .platform_data = &da830_evm_ui_expander_info,
- },
-};
-
-static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
- .bus_freq = 100, /* kHz */
- .bus_delay = 0, /* usec */
-};
-
/*
* USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
*/
* Set up USB clock/mode in the CFGCHIP2 register.
* FYI: CFGCHIP2 is 0x0000ef00 initially.
*/
- cfgchip2 = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG));
+ cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
/* USB2.0 PHY reference clock is 24 MHz */
cfgchip2 &= ~CFGCHIP2_REFFREQ;
cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
cfgchip2 |= CFGCHIP2_USB2PHYCLKMUX;
- __raw_writel(cfgchip2, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG));
+ /*
+ * We have to override VBUS/ID signals when MUSB is configured into the
+ * host-only mode -- ID pin will float if no cable is connected, so the
+ * controller won't be able to drive VBUS thinking that it's a B-device.
+ * Otherwise, we want to use the OTG mode and enable VBUS comparators.
+ */
+ cfgchip2 &= ~CFGCHIP2_OTGMODE;
+#ifdef CONFIG_USB_MUSB_HOST
+ cfgchip2 |= CFGCHIP2_FORCE_HOST;
+#else
+ cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
+#endif
+
+ __raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ /* USB_REFCLKIN is not used. */
+ ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
+ if (ret)
+ pr_warning("%s: USB 2.0 PinMux setup failed: %d\n",
+ __func__, ret);
+ else {
+ /*
+ * TPS2065 switch @ 5V supplies 1 A (sustains 1.5 A),
+ * with the power on to power good time of 3 ms.
+ */
+ ret = da8xx_register_usb20(1000, 3);
+ if (ret)
+ pr_warning("%s: USB 2.0 registration failed: %d\n",
+ __func__, ret);
+ }
- ret = da8xx_pinmux_setup(da830_evm_usb11_pins);
+ ret = davinci_cfg_reg_list(da830_evm_usb11_pins);
if (ret) {
pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
__func__, ret);
};
#define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1)
+#define DA830_MMCSD_CD_PIN GPIO_TO_PIN(2, 2)
static int da830_evm_mmc_get_ro(int index)
{
return gpio_get_value(DA830_MMCSD_WP_PIN);
}
+static int da830_evm_mmc_get_cd(int index)
+{
+ return !gpio_get_value(DA830_MMCSD_CD_PIN);
+}
+
static struct davinci_mmc_config da830_evm_mmc_config = {
.get_ro = da830_evm_mmc_get_ro,
- .wires = 4,
+ .get_cd = da830_evm_mmc_get_cd,
+ .wires = 8,
+ .max_freq = 50000000,
+ .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
.version = MMC_CTLR_VERSION_2,
};
{
int ret;
- ret = da8xx_pinmux_setup(da830_evm_mmc_sd_pins);
+ ret = davinci_cfg_reg_list(da830_evm_mmc_sd_pins);
if (ret) {
pr_warning("da830_evm_init: mmc/sd mux setup failed: %d\n",
ret);
}
gpio_direction_input(DA830_MMCSD_WP_PIN);
+ ret = gpio_request(DA830_MMCSD_CD_PIN, "MMC CD\n");
+ if (ret) {
+ pr_warning("da830_evm_init: can not open GPIO %d\n",
+ DA830_MMCSD_CD_PIN);
+ return;
+ }
+ gpio_direction_input(DA830_MMCSD_CD_PIN);
+
ret = da8xx_register_mmcsd0(&da830_evm_mmc_config);
if (ret) {
pr_warning("da830_evm_init: mmc/sd registration failed: %d\n",
}
}
+/*
+ * UI board NAND/NOR flashes only use 8-bit data bus.
+ */
+static const short da830_evm_emif25_pins[] = {
+ DA830_EMA_D_0, DA830_EMA_D_1, DA830_EMA_D_2, DA830_EMA_D_3,
+ DA830_EMA_D_4, DA830_EMA_D_5, DA830_EMA_D_6, DA830_EMA_D_7,
+ DA830_EMA_A_0, DA830_EMA_A_1, DA830_EMA_A_2, DA830_EMA_A_3,
+ DA830_EMA_A_4, DA830_EMA_A_5, DA830_EMA_A_6, DA830_EMA_A_7,
+ DA830_EMA_A_8, DA830_EMA_A_9, DA830_EMA_A_10, DA830_EMA_A_11,
+ DA830_EMA_A_12, DA830_EMA_BA_0, DA830_EMA_BA_1, DA830_NEMA_WE,
+ DA830_NEMA_CS_2, DA830_NEMA_CS_3, DA830_NEMA_OE, DA830_EMA_WAIT_0,
+ -1
+};
+
+#if defined(CONFIG_MMC_DAVINCI) || defined(CONFIG_MMC_DAVINCI_MODULE)
+#define HAS_MMC 1
+#else
+#define HAS_MMC 0
+#endif
+
+#ifdef CONFIG_DA830_UI_NAND
+static struct mtd_partition da830_evm_nand_partitions[] = {
+ /* bootloader (U-Boot, etc) in first sector */
+ [0] = {
+ .name = "bootloader",
+ .offset = 0,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ /* bootloader params in the next sector */
+ [1] = {
+ .name = "params",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ /* kernel */
+ [2] = {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_2M,
+ .mask_flags = 0,
+ },
+ /* file system */
+ [3] = {
+ .name = "filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ }
+};
+
+/* flash bbt decriptors */
+static uint8_t da830_evm_nand_bbt_pattern[] = { 'B', 'b', 't', '0' };
+static uint8_t da830_evm_nand_mirror_pattern[] = { '1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr da830_evm_nand_bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
+ NAND_BBT_WRITE | NAND_BBT_2BIT |
+ NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 2,
+ .len = 4,
+ .veroffs = 16,
+ .maxblocks = 4,
+ .pattern = da830_evm_nand_bbt_pattern
+};
+
+static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
+ NAND_BBT_WRITE | NAND_BBT_2BIT |
+ NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 2,
+ .len = 4,
+ .veroffs = 16,
+ .maxblocks = 4,
+ .pattern = da830_evm_nand_mirror_pattern
+};
+
+static struct davinci_nand_pdata da830_evm_nand_pdata = {
+ .parts = da830_evm_nand_partitions,
+ .nr_parts = ARRAY_SIZE(da830_evm_nand_partitions),
+ .ecc_mode = NAND_ECC_HW,
+ .ecc_bits = 4,
+ .options = NAND_USE_FLASH_BBT,
+ .bbt_td = &da830_evm_nand_bbt_main_descr,
+ .bbt_md = &da830_evm_nand_bbt_mirror_descr,
+};
+
+static struct resource da830_evm_nand_resources[] = {
+ [0] = { /* First memory resource is NAND I/O window */
+ .start = DA8XX_AEMIF_CS3_BASE,
+ .end = DA8XX_AEMIF_CS3_BASE + PAGE_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* Second memory resource is AEMIF control registers */
+ .start = DA8XX_AEMIF_CTL_BASE,
+ .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device da830_evm_nand_device = {
+ .name = "davinci_nand",
+ .id = 1,
+ .dev = {
+ .platform_data = &da830_evm_nand_pdata,
+ },
+ .num_resources = ARRAY_SIZE(da830_evm_nand_resources),
+ .resource = da830_evm_nand_resources,
+};
+
+static inline void da830_evm_init_nand(int mux_mode)
+{
+ int ret;
+
+ if (HAS_MMC) {
+ pr_warning("WARNING: both MMC/SD and NAND are "
+ "enabled, but they share AEMIF pins.\n"
+ "\tDisable MMC/SD for NAND support.\n");
+ return;
+ }
+
+ ret = davinci_cfg_reg_list(da830_evm_emif25_pins);
+ if (ret)
+ pr_warning("da830_evm_init: emif25 mux setup failed: %d\n",
+ ret);
+
+ ret = platform_device_register(&da830_evm_nand_device);
+ if (ret)
+ pr_warning("da830_evm_init: NAND device not registered.\n");
+
+ gpio_direction_output(mux_mode, 1);
+}
+#else
+static inline void da830_evm_init_nand(int mux_mode) { }
+#endif
+
+#ifdef CONFIG_DA830_UI_LCD
+static inline void da830_evm_init_lcdc(int mux_mode)
+{
+ int ret;
+
+ ret = davinci_cfg_reg_list(da830_lcdcntl_pins);
+ if (ret)
+ pr_warning("da830_evm_init: lcdcntl mux setup failed: %d\n",
+ ret);
+
+ ret = da8xx_register_lcdc(&sharp_lcd035q3dg01_pdata);
+ if (ret)
+ pr_warning("da830_evm_init: lcd setup failed: %d\n", ret);
+
+ gpio_direction_output(mux_mode, 0);
+}
+#else
+static inline void da830_evm_init_lcdc(int mux_mode) { }
+#endif
+
+static struct at24_platform_data da830_evm_i2c_eeprom_info = {
+ .byte_len = SZ_256K / 8,
+ .page_size = 64,
+ .flags = AT24_FLAG_ADDR16,
+ .setup = davinci_get_mac_addr,
+ .context = (void *)0x7f00,
+};
+
+static int __init da830_evm_ui_expander_setup(struct i2c_client *client,
+ int gpio, unsigned ngpio, void *context)
+{
+ gpio_request(gpio + 6, "UI MUX_MODE");
+
+ /* Drive mux mode low to match the default without UI card */
+ gpio_direction_output(gpio + 6, 0);
+
+ da830_evm_init_lcdc(gpio + 6);
+
+ da830_evm_init_nand(gpio + 6);
+
+ return 0;
+}
+
+static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
+ unsigned ngpio, void *context)
+{
+ gpio_free(gpio + 6);
+ return 0;
+}
+
+static struct pcf857x_platform_data __initdata da830_evm_ui_expander_info = {
+ .gpio_base = DAVINCI_N_GPIO,
+ .setup = da830_evm_ui_expander_setup,
+ .teardown = da830_evm_ui_expander_teardown,
+};
+
+static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("24c256", 0x50),
+ .platform_data = &da830_evm_i2c_eeprom_info,
+ },
+ {
+ I2C_BOARD_INFO("tlv320aic3x", 0x18),
+ },
+ {
+ I2C_BOARD_INFO("pcf8574", 0x3f),
+ .platform_data = &da830_evm_ui_expander_info,
+ },
+};
+
+static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
+ .bus_freq = 100, /* kHz */
+ .bus_delay = 0, /* usec */
+};
+
static __init void da830_evm_init(void)
{
struct davinci_soc_info *soc_info = &davinci_soc_info;
pr_warning("da830_evm_init: edma registration failed: %d\n",
ret);
- ret = da8xx_pinmux_setup(da830_i2c0_pins);
+ ret = davinci_cfg_reg_list(da830_i2c0_pins);
if (ret)
pr_warning("da830_evm_init: i2c0 mux setup failed: %d\n",
ret);
soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY;
soc_info->emac_pdata->rmii_en = 1;
- ret = da8xx_pinmux_setup(da830_cpgmac_pins);
+ ret = davinci_cfg_reg_list(da830_cpgmac_pins);
if (ret)
pr_warning("da830_evm_init: cpgmac mux setup failed: %d\n",
ret);
i2c_register_board_info(1, da830_evm_i2c_devices,
ARRAY_SIZE(da830_evm_i2c_devices));
- ret = da8xx_pinmux_setup(da830_evm_mcasp1_pins);
+ ret = davinci_cfg_reg_list(da830_evm_mcasp1_pins);
if (ret)
pr_warning("da830_evm_init: mcasp1 mux setup failed: %d\n",
ret);
da830_evm_init_mmc();
-#ifdef CONFIG_DA830_UI_LCD
- ret = da8xx_pinmux_setup(da830_lcdcntl_pins);
- if (ret)
- pr_warning("da830_evm_init: lcdcntl mux setup failed: %d\n",
- ret);
-
- ret = da8xx_register_lcdc(&sharp_lcd035q3dg01_pdata);
- if (ret)
- pr_warning("da830_evm_init: lcd setup failed: %d\n", ret);
-#endif
-
ret = da8xx_register_rtc();
if (ret)
pr_warning("da830_evm_init: rtc setup failed: %d\n", ret);
console_initcall(da830_evm_console_init);
#endif
-static __init void da830_evm_irq_init(void)
-{
- struct davinci_soc_info *soc_info = &davinci_soc_info;
-
- cp_intc_init((void __iomem *)DA8XX_CP_INTC_VIRT, DA830_N_CP_INTC_IRQ,
- soc_info->intc_irq_prios);
-}
-
static void __init da830_evm_map_io(void)
{
da830_init();
}
-MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP L137 EVM")
+MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM")
.phys_io = IO_PHYS,
.io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = da830_evm_map_io,
- .init_irq = da830_evm_irq_init,
+ .init_irq = cp_intc_init,
.timer = &davinci_timer,
.init_machine = da830_evm_init,
MACHINE_END