#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
+#include <linux/i2c/at24.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
-#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam926x_mc.h>
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+#include "sam9_smc.h"
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 5 = USART0 .. USART5
- * 6 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 3,
- .tty_map = { 6, 0, 1, -1, -1, -1, -1 } /* ttyS0, ..., ttyS6 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91sam9260_initialize(18432000);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
/*
+ * Audio
+ */
+static struct at73c213_board_info at73c213_data = {
+ .ssc_id = 0,
+ .shortname = "AT91SAM9260-EK external DAC",
+};
+
+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+static void __init at73c213_set_clk(struct at73c213_board_info *info)
+{
+ struct clk *pck0;
+ struct clk *plla;
+
+ pck0 = clk_get(NULL, "pck0");
+ plla = clk_get(NULL, "plla");
+
+ /* AT73C213 MCK Clock */
+ at91_set_B_periph(AT91_PIN_PC1, 0); /* PCK0 */
+
+ clk_set_parent(pck0, plla);
+ clk_put(plla);
+
+ info->dac_clk = pck0;
+}
+#else
+static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
+#endif
+
+/*
* SPI devices.
*/
static struct spi_board_info ek_spi_devices[] = {
},
#endif
#endif
-#if defined(CONFIG_SND_AT73C213)
+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
{ /* AT73C213 DAC */
- .modalias = "snd_at73c213",
+ .modalias = "at73c213",
.chip_select = 0,
.max_speed_hz = 10 * 1000 * 1000,
.bus_num = 1,
+ .mode = SPI_MODE_1,
+ .platform_data = &at73c213_data,
},
#endif
};
{
.name = "Partition 1",
.offset = 0,
- .size = 256 * 1024,
+ .size = SZ_256K,
},
{
.name = "Partition 2",
- .offset = 256 * 1024,
+ .offset = MTDPART_OFS_NXTBLK,
.size = MTDPART_SIZ_FULL,
},
};
return ek_nand_partition;
}
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#endif
};
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 1,
+ .ncs_write_setup = 0,
+ .nwe_setup = 1,
+
+ .ncs_read_pulse = 3,
+ .nrd_pulse = 3,
+ .ncs_write_pulse = 3,
+ .nwe_pulse = 3,
+
+ .read_cycle = 5,
+ .write_cycle = 5,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+ .tdf_cycles = 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+ /* setup bus-width (8 or 16) */
+ if (ek_nand_data.bus_width_16)
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+ else
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(3, &ek_nand_smc_config);
+
+ at91_add_device_nand(&ek_nand_data);
+}
+
/*
* MCI (SD/MMC)
// .vcc_pin = ... not connected
};
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+ { /* "bottom" led, green, userled1 to be defined */
+ .name = "ds5",
+ .gpio = AT91_PIN_PA6,
+ .active_low = 1,
+ .default_trigger = "none",
+ },
+ { /* "power" led, yellow */
+ .name = "ds1",
+ .gpio = AT91_PIN_PA9,
+ .default_trigger = "heartbeat",
+ }
+};
+
+/*
+ * I2C devices
+ */
+static struct at24_platform_data at24c512 = {
+ .byte_len = SZ_512K / 8,
+ .page_size = 128,
+ .flags = AT24_FLAG_ADDR16,
+};
+
+static struct i2c_board_info __initdata ek_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("24c512", 0x50),
+ .platform_data = &at24c512,
+ },
+ /* more devices can be added using expansion connectors */
+};
+
+
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+ {
+ .gpio = AT91_PIN_PA30,
+ .code = BTN_3,
+ .desc = "Button 3",
+ .active_low = 1,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PA31,
+ .code = BTN_4,
+ .desc = "Button 4",
+ .active_low = 1,
+ .wakeup = 1,
+ }
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+ .buttons = ek_buttons,
+ .nbuttons = ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &ek_button_data,
+ }
+};
+
+static void __init ek_add_device_buttons(void)
+{
+ at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */
+ at91_set_deglitch(AT91_PIN_PA30, 1);
+ at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */
+ at91_set_deglitch(AT91_PIN_PA31, 1);
+
+ platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+
static void __init ek_board_init(void)
{
/* Serial */
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
- at91_add_device_nand(&ek_nand_data);
+ ek_add_device_nand();
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
+ /* I2C */
+ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
+ /* SSC (to AT73C213) */
+ at73c213_set_clk(&at73c213_data);
+ at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+ /* Push Buttons */
+ ek_add_device_buttons();
}
MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff