- Default: 1
- For auto-loading more than one card, specify this
option together with snd-card-X aliases.
- device_mode
- - permission mask for dynamic sound device filesystem
- - This is available only when DEVFS is enabled
- - Default: 0666
- - E.g.: device_mode=0660
Module snd-pcm-oss
Each of top level sound card module takes the following options.
index - index (slot #) of sound card
- - Values: 0 through 7 or negative
+ - Values: 0 through 31 or negative
- If nonnegative, assign that index number
- if negative, interpret as a bitmask of permissible
indices; the first free permitted index is assigned
enable - enable card
- Default: enabled, for PCI and ISA PnP cards
+ Module snd-adlib
+ ----------------
+
+ Module for AdLib FM cards.
+
+ port - port # for OPL chip
+
+ This module supports multiple cards. It does not support autoprobe, so
+ the port must be specified. For actual AdLib FM cards it will be 0x388.
+ Note that this card does not have PCM support and no mixer; only FM
+ synthesis.
+
+ Make sure you have "sbiload" from the alsa-tools package available and,
+ after loading the module, find out the assigned ALSA sequencer port
+ number through "sbiload -l". Example output:
+
+ Port Client name Port name
+ 64:0 OPL2 FM synth OPL2 FM Port
+
+ Load the std.sb and drums.sb patches also supplied by sbiload:
+
+ sbiload -p 64:0 std.sb drums.sb
+
+ If you use this driver to drive an OPL3, you can use std.o3 and drums.o3
+ instead. To have the card produce sound, use aplaymidi from alsa-utils:
+
+ aplaymidi -p 64:0 foo.mid
+
Module snd-ad1816a
------------------
dma2 - second DMA # for AD1816A chip (PnP setup)
clockfreq - Clock frequency for AD1816A chip (default = 0, 33000Hz)
- Module supports up to 8 cards, autoprobe and PnP.
+ This module supports multiple cards, autoprobe and PnP.
Module snd-ad1848
-----------------
irq - IRQ # for AD1848 chip
dma1 - DMA # for AD1848 chip (0,1,3)
- Module supports up to 8 cards. This module does not support autoprobe
+ This module supports multiple cards. It does not support autoprobe
thus main port must be specified!!! Other ports are optional.
+ The power-management is supported.
+
Module snd-ad1889
-----------------
ac97_quirk - AC'97 workaround for strange hardware
See the description of intel8x0 module for details.
- This module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-ali5451
------------------
spdif - Support SPDIF I/O
- Default: disabled
- Module supports autoprobe and multiple chips (max 8).
+ This module supports one chip and autoprobe.
The power-management is supported.
mpu_irq - IRQ # for MPU-401 (PnP setup)
fm_port - port # for OPL3 FM (PnP setup)
- Module supports up to 8 cards, autoprobe and PnP.
+ This module supports multiple cards, autoprobe and PnP.
+
+ The power-management is supported.
+
+ Module snd-als300
+ -----------------
+
+ Module for Avance Logic ALS300 and ALS300+
+
+ This module supports multiple cards.
+
+ The power-management is supported.
Module snd-als4000
------------------
joystick_port - port # for legacy joystick support.
0 = disabled (default), 1 = auto-detect
- Module supports up to 8 cards, autoprobe and PnP.
+ This module supports multiple cards, autoprobe and PnP.
+
+ The power-management is supported.
Module snd-atiixp
-----------------
implementation depends on the motherboard, and you'll need to
choose the correct one via spdif_aclink module option.
+ The power-management is supported.
+
Module snd-atiixp-modem
-----------------------
Note: The default index value of this module is -2, i.e. the first
slot is excluded.
+ The power-management is supported.
+
Module snd-au8810, snd-au8820, snd-au8830
-----------------------------------------
dma1 - 1st DMA # for AZT2320 (WSS) chip (PnP setup)
dma2 - 2nd DMA # for AZT2320 (WSS) chip (PnP setup)
- Module supports up to 8 cards, PnP and autoprobe.
+ This module supports multiple cards, PnP and autoprobe.
+ The power-management is supported.
+
Module snd-azt3328
------------------
joystick - Enable joystick (default off)
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-bt87x
----------------
digital_rate - Override the default digital rate (Hz)
load_all - Load the driver even if the card model isn't known
- Module supports up to 8 cards.
+ This module supports multiple cards.
Note: The default index value of this module is -2, i.e. the first
slot is excluded.
Module for Creative Audigy LS and SB Live 24bit
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-cmi8330
sbdma8 - 8bit DMA # for CMI8330 chip (SB16)
sbdma16 - 16bit DMA # for CMI8330 chip (SB16)
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
+
+ The power-management is supported.
Module snd-cmipci
-----------------
Module for C-Media CMI8338 and 8738 PCI sound cards.
- mpu_port - 0x300,0x310,0x320,0x330, 0 = disable (default)
+ mpu_port - 0x300,0x310,0x320,0x330 = legacy port,
+ 1 = integrated PCI port,
+ 0 = disable (default)
fm_port - 0x388 (default), 0 = disable (default)
soft_ac3 - Software-conversion of raw SPDIF packets (model 033 only)
(default = 1)
joystick_port - Joystick port address (0 = disable, 1 = auto-detect)
- Module supports autoprobe and multiple chips (max 8).
+ This module supports autoprobe and multiple cards.
+ The power-management is supported.
+
Module snd-cs4231
-----------------
dma1 - first DMA # for CS4231 chip
dma2 - second DMA # for CS4231 chip
- Module supports up to 8 cards. This module does not support autoprobe
+ This module supports multiple cards. This module does not support autoprobe
thus main port must be specified!!! Other ports are optional.
The power-management is supported.
dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
- Module supports up to 8 cards. This module does not support autoprobe
+ This module supports multiple cards. This module does not support autoprobe
thus main port must be specified!!! Other ports are optional.
The power-management is supported.
dma2 - second DMA # for CS4236 chip (0,1,3), -1 = disable
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
- Module supports up to 8 cards. This module does not support autoprobe
+ This module supports multiple cards. This module does not support autoprobe
(if ISA PnP is not used) thus main port and control port must be
specified!!! Other ports are optional.
dual_codec - Secondary codec ID (0 = disable, default)
- Module supports up to 8 cards.
+ This module supports multiple cards.
The power-management is supported.
thinkpad - Force to enable Thinkpad's CLKRUN control.
mmap_valid - Support OSS mmap mode (default = 0).
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
Usually external amp and CLKRUN controls are detected automatically
from PCI sub vendor/device ids. If they don't work, give the options
above explicitly.
The power-management is supported.
+ Module snd-cs5535audio
+ ----------------------
+
+ Module for multifunction CS5535 companion PCI device
+
+ The power-management is supported.
+
+ Module snd-darla20
+ ------------------
+
+ Module for Echoaudio Darla20
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
+ Module snd-darla24
+ ------------------
+
+ Module for Echoaudio Darla24
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
Module snd-dt019x
-----------------
mpu_irq - IRQ # for MPU-401 (PnP setup)
dma8 - DMA # (PnP setup)
- Module supports up to 8 cards. This module is enabled only with
+ This module supports multiple cards. This module is enabled only with
ISA PnP support.
+ The power-management is supported.
+
Module snd-dummy
----------------
or input, but you may use this module for any application which
requires a sound card (like RealPlayer).
+ The power-management is supported.
+
+ Module snd-echo3g
+ -----------------
+
+ Module for Echoaudio 3G cards (Gina3G/Layla3G)
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
Module snd-emu10k1
------------------
given in MB unit. Default value is 128.
enable_ir - enable IR
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
Input & Output configurations [extin/extout]
* Creative Card wo/Digital out [0x0003/0x1f03]
* Creative Card 5.1 (c) 2003 [0x3fc3/0x7cff]
* Creative Card all ins and outs [0x3fff/0x7fff]
+ The power-management is supported.
+
Module snd-emu10k1x
-------------------
Module for Creative Emu10k1X (SB Live Dell OEM version)
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-ens1370
------------------
joystick - Enable joystick (default off)
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
+ The power-management is supported.
+
Module snd-ens1371
------------------
joystick_port - port # for joystick (0x200,0x208,0x210,0x218),
0 = disable (default), 1 = auto-detect
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
+ The power-management is supported.
+
Module snd-es968
----------------
irq - IRQ # for ES968 (SB8) chip (PnP setup)
dma1 - DMA # for ES968 (SB8) chip (PnP setup)
- Module supports up to 8 cards, PnP and autoprobe.
+ This module supports multiple cards, PnP and autoprobe.
+ The power-management is supported.
+
Module snd-es1688
-----------------
mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
dma8 - DMA # for ES-1688 chip (0,1,3)
- Module supports up to 8 cards and autoprobe (without MPU-401 port).
+ This module supports multiple cards and autoprobe (without MPU-401 port).
Module snd-es18xx
-----------------
dma2 - first DMA # for ES-18xx chip (0,1,3)
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
- Module supports up to 8 cards ISA PnP and autoprobe (without MPU-401 port
- if native ISA PnP routines are not used).
+ This module supports multiple cards, ISA PnP and autoprobe (without MPU-401
+ port if native ISA PnP routines are not used).
When dma2 is equal with dma1, the driver works as half-duplex.
The power-management is supported.
Module for sound cards based on ESS Solo-1 (ES1938,ES1946) chips.
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
+
+ The power-management is supported.
Module snd-es1968
-----------------
enable_mpu - enable MPU401 (0 = off, 1 = on, 2 = auto (default))
joystick - enable joystick (default off)
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
The power-management is supported.
- High 16-bits are video (radio) device number + 1
- example: 0x10002 (MediaForte 256-PCPR, device 1)
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
+ The power-management is supported.
+
+ Module snd-gina20
+ -----------------
+
+ Module for Echoaudio Gina20
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
+ Module snd-gina24
+ -----------------
+
+ Module for Echoaudio Gina24
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
Module snd-gusclassic
---------------------
voices - GF1 voices limit (14-32)
pcm_voices - reserved PCM voices
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
Module snd-gusextreme
---------------------
voices - GF1 voices limit (14-32)
pcm_voices - reserved PCM voices
- Module supports up to 8 cards and autoprobe (without MPU-401 port).
+ This module supports multiple cards and autoprobe (without MPU-401 port).
Module snd-gusmax
-----------------
voices - GF1 voices limit (14-32)
pcm_voices - reserved PCM voices
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
Module snd-hda-intel
--------------------
- Module for Intel HD Audio (ICH6, ICH6M, ICH7), ATI SB450,
- VIA VT8251/VT8237A
+ Module for Intel HD Audio (ICH6, ICH6M, ESB2, ICH7, ICH8),
+ ATI SB450, SB600, RS600,
+ VIA VT8251/VT8237A,
+ SIS966, ULI M5461
model - force the model name
position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
+ single_cmd - Use single immediate commands to communicate with
+ codecs (for debugging only)
+ enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
This module supports one card and autoprobe.
6stack-digout 6-jack with a SPDIF out
w810 3-jack
z71v 3-jack (HP shared SPDIF)
- asus 3-jack
+ asus 3-jack (ASUS Mobo)
+ asus-w1v ASUS W1V
+ asus-dig ASUS with SPDIF out
+ asus-dig2 ASUS with SPDIF out (using GPIO2)
uniwill 3-jack
F1734 2-jack
+ lg LG laptop (m1 express dual)
+ lg-lw LG LW20/LW25 laptop
+ tcl TCL S700
+ clevo Clevo laptops (m520G, m665n)
test for testing/debugging purpose, almost all controls can be
adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
+ auto auto-config reading BIOS (default)
ALC260
hp HP machines
+ hp-3013 HP machines (3013-variant)
fujitsu Fujitsu S7020
+ acer Acer TravelMate
+ basic fixed pin assignment (old default model)
+ auto auto-config reading BIOS (default)
+
+ ALC262
+ fujitsu Fujitsu Laptop
+ hp-bpc HP xw4400/6400/8400/9400 laptops
+ benq Benq ED8
+ hippo Hippo (ATI) with jack detection
+ hippo_1 Hippo (Benq) with jack detection
+ basic fixed pin assignment w/o SPDIF
+ auto auto-config reading BIOS (default)
+
+ ALC882/885
+ 3stack-dig 3-jack with SPDIF I/O
+ 6stck-dig 6-jack digital with SPDIF I/O
+ arima Arima W820Di1
+ auto auto-config reading BIOS (default)
+
+ ALC883/888
+ 3stack-dig 3-jack with SPDIF I/O
+ 6stack-dig 6-jack digital with SPDIF I/O
+ 3stack-6ch 3-jack 6-channel
+ 3stack-6ch-dig 3-jack 6-channel with SPDIF I/O
+ 6stack-dig-demo 6-jack digital for Intel demo board
+ acer Acer laptops (Travelmate 3012WTMi, Aspire 5600, etc)
+ medion Medion Laptops
+ targa-dig Targa/MSI
+ targa-2ch-dig Targs/MSI with 2-channel
+ auto auto-config reading BIOS (default)
+
+ ALC861/660
+ 3stack 3-jack
+ 3stack-dig 3-jack with SPDIF I/O
+ 6stack-dig 6-jack with SPDIF I/O
+ 3stack-660 3-jack (for ALC660)
+ uniwill-m31 Uniwill M31 laptop
+ toshiba Toshiba laptop support
+ auto auto-config reading BIOS (default)
CMI9880
minimal 3-jack in back
allout 5-jack in back, 2-jack in front, SPDIF out
auto auto-config reading BIOS (default)
+ AD1981
+ basic 3-jack (default)
+ hp HP nx6320
+ thinkpad Lenovo Thinkpad T60/X60/Z60
+
+ AD1986A
+ 6stack 6-jack, separate surrounds (default)
+ 3stack 3-stack, shared surrounds
+ laptop 2-channel only (FSC V2060, Samsung M50)
+ laptop-eapd 2-channel with EAPD (Samsung R65, ASUS A6J)
+
+ AD1988
+ 6stack 6-jack
+ 6stack-dig ditto with SPDIF
+ 3stack 3-jack
+ 3stack-dig ditto with SPDIF
+ laptop 3-jack with hp-jack automute
+ laptop-dig ditto with SPDIF
+ auto auto-config reading BIOS (default)
+
+ STAC9200/9205/9220/9221/9254
+ ref Reference board
+ 3stack D945 3stack
+ 5stack D945 5stack + SPDIF
+
+ STAC9227/9228/9229/927x
+ ref Reference board
+ 3stack D965 3stack
+ 5stack D965 5stack + SPDIF
+
+ STAC9872
+ vaio Setup for VAIO FE550G/SZ110
+ vaio-ar Setup for VAIO AR
+
If the default configuration doesn't work and one of the above
matches with your device, report it together with the PCI
subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
(Usually SD_LPLIB register is more accurate than the
position buffer.)
+ NB: If you get many "azx_get_response timeout" messages at
+ loading, it's likely a problem of interrupts (e.g. ACPI irq
+ routing). Try to boot with options like "pci=noacpi". Also, you
+ can try "single_cmd=1" module option. This will switch the
+ communication method between HDA controller and codecs to the
+ single immediate commands instead of CORB/RIRB. Basically, the
+ single command mode is provided only for BIOS, and you won't get
+ unsolicited events, too. But, at least, this works independently
+ from the irq. Remember this is a last resort, and should be
+ avoided as much as possible...
+
+ The power-management is supported.
+
Module snd-hdsp
---------------
Module for RME Hammerfall DSP audio interface(s)
- Module supports up to 8 cards.
+ This module supports multiple cards.
Note: The firmware data can be automatically loaded via hotplug
when CONFIG_FW_LOADER is set. Otherwise, you need to load
dmx6fire, dsp24, dsp24_value, dsp24_71, ez8,
phase88, mediastation
omni - Omni I/O support for MidiMan M-Audio Delta44/66
- cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transciever)
+ cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transceiver)
in msec resolution, default value is 500 (0.5 sec)
- Module supports up to 8 cards and autoprobe. Note: The consumer part
+ This module supports multiple cards and autoprobe. Note: The consumer part
is not used with all Envy24 based cards (for example in the MidiMan Delta
serie).
------------------
Module for Envy24HT (VT/ICE1724), Envy24PT (VT1720) based PCI sound cards.
+ * MidiMan M Audio Revolution 5.1
* MidiMan M Audio Revolution 7.1
* AMP Ltd AUDIO2000
* TerraTec Aureon 5.1 Sky
* TerraTec Phase 22
* TerraTec Phase 28
* AudioTrak Prodigy 7.1
+ * AudioTrak Prodigy 7.1LT
* AudioTrak Prodigy 192
* Pontis MS300
* Albatron K8X800 Pro II
* Shuttle SN25P
model - Use the given board model, one of the following:
- revo71, amp2000, prodigy71, prodigy192, aureon51,
- aureon71, universe, k8x800, phase22, phase28, ms300,
- av710
+ revo51, revo71, amp2000, prodigy71, prodigy71lt,
+ prodigy192, aureon51, aureon71, universe,
+ k8x800, phase22, phase28, ms300, av710
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
Note: The supported board is detected by reading EEPROM or PCI
SSID (if EEPROM isn't available). You can override the
driver isn't configured properly or you want to try another
type for testing.
+ Module snd-indigo
+ -----------------
+
+ Module for Echoaudio Indigo
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
+ Module snd-indigodj
+ -------------------
+
+ Module for Echoaudio Indigo DJ
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
+ Module snd-indigoio
+ -------------------
+
+ Module for Echoaudio Indigo IO
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
Module snd-intel8x0
-------------------
Module for AC'97 motherboards from Intel and compatibles.
* Intel i810/810E, i815, i820, i830, i84x, MX440
+ ICH5, ICH6, ICH7, ESB2
* SiS 7012 (SiS 735)
- * NVidia NForce, NForce2
+ * NVidia NForce, NForce2, NForce3, MCP04, CK804
+ CK8, CK8S, MCP501
* AMD AMD768, AMD8111
* ALi m5455
--------------------
Module for Intel ICH (i8x0) chipset MC97 modems.
+ * Intel i810/810E, i815, i820, i830, i84x, MX440
+ ICH5, ICH6, ICH7
+ * SiS 7013 (SiS 735)
+ * NVidia NForce, NForce2, NForce2s, NForce3
+ * AMD AMD8111
+ * ALi m5455
ac97_clock - AC'97 codec clock base (0 = auto-detect)
Note: The default index value of this module is -2, i.e. the first
slot is excluded.
+ The power-management is supported.
+
Module snd-interwave
--------------------
effect - 1 = InterWave effects enable (default 0);
requires 8 voices
- Module supports up to 8 cards, autoprobe and ISA PnP.
+ This module supports multiple cards, autoprobe and ISA PnP.
Module snd-interwave-stb
------------------------
effect - 1 = InterWave effects enable (default 0);
requires 8 voices
- Module supports up to 8 cards, autoprobe and ISA PnP.
+ This module supports multiple cards, autoprobe and ISA PnP.
Module snd-korg1212
-------------------
Module for Korg 1212 IO PCI card
- Module supports up to 8 cards.
+ This module supports multiple cards.
+
+ Module snd-layla20
+ ------------------
+
+ Module for Echoaudio Layla20
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
+ Module snd-layla24
+ ------------------
+
+ Module for Echoaudio Layla24
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
Module snd-maestro3
-------------------
-1 for default pin (8 for allegro, 1 for
others)
- Module supports autoprobe and multiple chips (max 8).
+ This module supports autoprobe and multiple chips.
Note: the binding of amplifier is dependent on hardware.
If there is no sound even though all channels are unmuted, try to
The power-management is supported.
+ Module snd-mia
+ ---------------
+
+ Module for Echoaudio Mia
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
+ Module snd-miro
+ ---------------
+
+ Module for Miro soundcards: miroSOUND PCM 1 pro,
+ miroSOUND PCM 12,
+ miroSOUND PCM 20 Radio.
+
+ port - Port # (0x530,0x604,0xe80,0xf40)
+ irq - IRQ # (5,7,9,10,11)
+ dma1 - 1st dma # (0,1,3)
+ dma2 - 2nd dma # (0,1)
+ mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330)
+ mpu_irq - MPU-401 irq # (5,7,9,10)
+ fm_port - FM Port # (0x388)
+ wss - enable WSS mode
+ ide - enable onboard ide support
+
Module snd-mixart
-----------------
Module for Digigram miXart8 sound cards.
- Module supports multiple cards.
+ This module supports multiple cards.
Note: One miXart8 board will be represented as 4 alsa cards.
See MIXART.txt for details.
When no hotplug fw loader is available, you need to load the
firmware via mixartloader utility in alsa-tools package.
+ Module snd-mona
+ ---------------
+
+ Module for Echoaudio Mona
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+
Module snd-mpu401
-----------------
irq - IRQ number or -1 (disable)
pnp - PnP detection - 0 = disable, 1 = enable (default)
- Module supports multiple devices (max 8) and PnP.
+ This module supports multiple devices and PnP.
Module snd-mtpav
----------------
Module supports only 1 card. This module has no enable option.
+ Module snd-mts64
+ ----------------
+
+ Module for Ego Systems (ESI) Miditerminal 4140
+
+ This module supports multiple devices.
+ Requires parport (CONFIG_PARPORT).
+
Module snd-nm256
----------------
use_cache - 0 or 1 (disabled by default)
vaio_hack - alias buffer_top=0x25a800
reset_workaround - enable AC97 RESET workaround for some laptops
+ reset_workaround2 - enable extended AC97 RESET workaround for some
+ other laptops
- Module supports autoprobe and multiple chips (max 8).
+ This module supports one chip and autoprobe.
The power-management is supported.
Note: on some notebooks the buffer address cannot be detected
automatically, or causes hang-up during initialization.
- In such a case, specify the buffer top address explicity via
- buffer_top option.
+ In such a case, specify the buffer top address explicitly via
+ the buffer_top option.
For example,
Sony F250: buffer_top=0x25a800
Sony F270: buffer_top=0x272800
workaround is enabled automatically. For other laptops with a
hard freeze, you can try reset_workaround=1 option.
+ Note: Dell Latitude CSx laptops have another problem regarding
+ AC97 RESET. On these laptops, reset_workaround2 option is
+ turned on as default. This option is worth to try if the
+ previous reset_workaround option doesn't help.
+
Note: This driver is really crappy. It's a porting from the
OSS driver, which is a result of black-magic reverse engineering.
The detection of codec will fail if the driver is loaded *after*
dma2 - second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
- Module supports up to 8 cards and ISA PnP. This module does not support
+ This module supports multiple cards and ISA PnP. It does not support
autoprobe (if ISA PnP is not used) thus all ports must be specified!!!
The power-management is supported.
This module supports only one card, autoprobe and PnP.
+ Module snd-pcxhr
+ ----------------
+
+ Module for Digigram PCXHR boards
+
+ This module supports multiple cards.
+
Module snd-powermac (on ppc only)
---------------------------------
For ARM architecture only.
+ The power-management is supported.
+
+ Module snd-riptide
+ ------------------
+
+ Module for Conexant Riptide chip
+
+ joystick_port - Joystick port # (default: 0x200)
+ mpu_port - MPU401 port # (default: 0x330)
+ opl3_port - OPL3 port # (default: 0x388)
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+ You need to install the firmware file "riptide.hex" to the standard
+ firmware path (e.g. /lib/firmware).
+
Module snd-rme32
----------------
Module for RME Digi32, Digi32 Pro and Digi32/8 (Sek'd Prodif32,
Prodif96 and Prodif Gold) sound cards.
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-rme96
----------------
Module for RME Digi96, Digi96/8 and Digi96/8 PRO/PAD/PST sound cards.
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-rme9652
------------------
precise_ptr - Enable precise pointer (doesn't work reliably).
(default = 0)
- Module supports up to 8 cards.
+ This module supports multiple cards.
Note: snd-page-alloc module does the job which snd-hammerfall-mem
module did formerly. It will allocate the buffers in advance
Module supports only one card.
Module has no enable and index options.
+ The power-management is supported.
+
Module snd-sb8
--------------
irq - IRQ # for SB DSP chip (5,7,9,10)
dma8 - DMA # for SB DSP chip (1,3)
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
+ The power-management is supported.
+
Module snd-sb16 and snd-sbawe
-----------------------------
csp - ASP/CSP chip support - 0 = disable (default), 1 = enable
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
- Module supports up to 8 cards, autoprobe and ISA PnP.
+ This module supports multiple cards, autoprobe and ISA PnP.
Note: To use Vibra16X cards in 16-bit half duplex mode, you must
disable 16bit DMA with dma16 = -1 module parameter.
half duplex mode through 8-bit DMA channel by disabling their
16-bit DMA channel.
+ The power-management is supported.
+
Module snd-sgalaxy
------------------
irq - IRQ # (7,9,10,11)
dma1 - DMA #
- Module supports up to 8 cards.
+ This module supports multiple cards.
+
+ The power-management is supported.
Module snd-sscape
-----------------
mpu_irq - MPU-401 IRQ # (PnP setup)
dma - DMA # (PnP setup)
- Module supports up to 8 cards. ISA PnP must be enabled.
+ This module supports multiple cards. ISA PnP must be enabled.
You need sscape_ctl tool in alsa-tools package for loading
the microcode.
Module for AMD7930 sound chips found on Sparcs.
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-sun-cs4231 (on sparc only)
-------------------------------------
Module for CS4231 sound chips found on Sparcs.
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-sun-dbri (on sparc only)
-----------------------------------
Module for DBRI sound chips found on Sparcs.
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-wavefront
--------------------
dma2 - DMA2 # for CS4232 PCM interface.
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
- Module supports up to 8 cards and ISA PnP.
+ This module supports multiple cards and ISA PnP.
Module snd-sonicvibes
---------------------
- SoundCard must have onboard SRAM for this.
mge - Mic Gain Enable - 1 = enable, 0 = disable (default)
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
Module snd-serial-u16550
------------------------
0 = Soundcanvas, 1 = MS-124T, 2 = MS-124W S/A,
3 = MS-124W M/B, 4 = Generic
- Module supports up to 8 cards. This module does not support autoprobe
+ This module supports multiple cards. This module does not support autoprobe
thus the main port must be specified!!! Other options are optional.
Module snd-trident
pcm_channels - max channels (voices) reserved for PCM
wavetable_size - max wavetable size in kB (4-?kb)
- Module supports up to 8 cards and autoprobe.
+ This module supports multiple cards and autoprobe.
The power-management is supported.
vid - Vendor ID for the device (optional)
pid - Product ID for the device (optional)
+ device_setup - Device specific magic number (optional)
+ - Influence depends on the device
+ - Default: 0x0000
- This module supports up to 8 cards, autoprobe and hotplugging.
+ This module supports multiple devices, autoprobe and hotplugging.
Module snd-usb-usx2y
--------------------
Module for Tascam USB US-122, US-224 and US-428 devices.
- This module supports up to 8 cards, autoprobe and hotplugging.
+ This module supports multiple devices, autoprobe and hotplugging.
Note: you need to load the firmware via usx2yloader utility included
in alsa-tools and alsa-firmware packages.
Note: for the MPU401 on VIA823x, use snd-mpu401 driver
additionally. The mpu_port option is for VIA686 chips only.
+ The power-management is supported.
+
Module snd-via82xx-modem
------------------------
Note: The default index value of this module is -2, i.e. the first
slot is excluded.
+ The power-management is supported.
+
Module snd-virmidi
------------------
This module creates virtual rawmidi devices which communicate
to the corresponding ALSA sequencer ports.
- midi_devs - MIDI devices # (1-8, default=4)
+ midi_devs - MIDI devices # (1-4, default=4)
- Module supports up to 8 cards.
+ This module supports multiple cards.
Module snd-vx222
----------------
mic - Enable Microphone on V222 Mic (NYI)
ibl - Capture IBL size. (default = 0, minimum size)
- Module supports up to 8 cards.
+ This module supports multiple cards.
When the driver is compiled as a module and the hotplug firmware
is supported, the firmware data is loaded via hotplug automatically.
size is chosen. The possible IBL values can be found in
/proc/asound/cardX/vx-status proc file.
+ The power-management is supported.
+
Module snd-vxpocket
-------------------
ibl - Capture IBL size. (default = 0, minimum size)
- Module supports up to 8 cards. The module is compiled only when
+ This module supports multiple cards. The module is compiled only when
PCMCIA is supported on kernel.
With the older 2.6.x kernel, to activate the driver via the card
About capture IBL, see the description of snd-vx222 module.
- Note: the driver is build only when CONFIG_ISA is set.
-
- Note2: snd-vxp440 driver is merged to snd-vxpocket driver since
+ Note: snd-vxp440 driver is merged to snd-vxpocket driver since
ALSA 1.0.10.
+ The power-management is supported.
+
Module snd-ymfpci
-----------------
1 (auto-detect)
rear_switch - enable shared rear/line-in switch (bool)
- Module supports autoprobe and multiple chips (max 8).
+ This module supports autoprobe and multiple chips.
The power-management is supported.
Module for Sound Core PDAudioCF sound card.
- Note: the driver is build only when CONFIG_ISA is set.
+ The power-management is supported.
AC97 Quirk Option
The following strings are accepted:
- default Don't override the default setting
- - disable Disable the quirk
+ - none Disable the quirk
- hp_only Bind Master and Headphone controls as a single control
- swap_hp Swap headphone and master controls
- swap_surround Swap master and surround controls
# OSS/Free portion
alias sound-slot-0 snd-interwave
alias sound-slot-1 snd-ens1371
------ /etc/moprobe.conf
+----- /etc/modprobe.conf
In this example, the interwave card is always loaded as the first card
(index 0) and ens1371 as the second (index 1).
options of snd-pcm-oss module.
-DEVFS support
-=============
-
-The ALSA driver fully supports the devfs extension.
-You should add lines below to your devfsd.conf file:
-
-LOOKUP snd MODLOAD ACTION snd
-REGISTER ^sound/.* PERMISSIONS root.audio 660
-REGISTER ^snd/.* PERMISSIONS root.audio 660
-
-Warning: These lines assume that you have the audio group in your system.
- Otherwise replace audio word with another group name (root for
- example).
-
-
Proc interfaces (/proc/asound)
==============================