V4L/DVB: em28xx: add em286x/tvp5150 reference design

[safe/jmp/linux-2.6] / Documentation / mips / AU1xxx_IDE.README

diff --git a/Documentation/mips/AU1xxx_IDE.README b/Documentation/mips/AU1xxx_IDE.README
index 5c83341..8ace35e 100644 (file)
--- a/Documentation/mips/AU1xxx_IDE.README
+++ b/Documentation/mips/AU1xxx_IDE.README
@@ -44,30 +44,20 @@ FILES, CONFIGS AND COMPATABILITY
 
 Two files are introduced:
 
-  a) 'include/asm-mips/mach-au1x00/au1xxx_ide.h'
+  a) 'arch/mips/include/asm/mach-au1x00/au1xxx_ide.h'
      containes : struct _auide_hwif
-                 struct drive_list_entry dma_white_list
-                 struct drive_list_entry dma_black_list
                  timing parameters for PIO mode 0/1/2/3/4
                  timing parameters for MWDMA 0/1/2
 
   b) 'drivers/ide/mips/au1xxx-ide.c'
      contains the functionality of the AU1XXX IDE driver
 
-Four configs variables are introduced:
+Following extra configs variables are introduced:
 
   CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA    - enable the PIO+DBDMA mode
   CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA  - enable the MWDMA mode
   CONFIG_BLK_DEV_IDE_AU1XXX_BURSTABLE_ON - set Burstable FIFO in DBDMA
                                            controller
-  CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ - maximum transfer size
-                                           per descriptor
-
-If MWDMA is enabled and the connected hard disc is not on the white list, the
-kernel switches to a "safe mwdma mode" at boot time. In this mode the IDE
-performance is substantial slower then in full speed mwdma. In this case
-please add your hard disc to the white list (follow instruction from 'ADD NEW
-HARD DISC TO WHITE OR BLACK LIST' section).
 
 
 SUPPORTED IDE MODES
@@ -95,7 +85,6 @@ CONFIG_BLK_DEV_IDEDMA_PCI=y
 CONFIG_IDEDMA_PCI_AUTO=y
 CONFIG_BLK_DEV_IDE_AU1XXX=y
 CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=y
-CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ=128
 CONFIG_BLK_DEV_IDEDMA=y
 CONFIG_IDEDMA_AUTO=y
 
@@ -113,51 +102,12 @@ CONFIG_BLK_DEV_IDEDMA_PCI=y
 CONFIG_IDEDMA_PCI_AUTO=y
 CONFIG_BLK_DEV_IDE_AU1XXX=y
 CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=y
-CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ=128
 CONFIG_BLK_DEV_IDEDMA=y
 CONFIG_IDEDMA_AUTO=y
 
 Also undefine 'IDE_AU1XXX_BURSTMODE' in 'drivers/ide/mips/au1xxx-ide.c' to
 disable the burst support on DBDMA controller.
 
-ADD NEW HARD DISC TO WHITE OR BLACK LIST
-----------------------------------------
-
-Step 1 : detect the model name of your hard disc
-
-  a) connect your hard disc to the AU1XXX
-
-  b) boot your kernel and get the hard disc model.
-
-     Example boot log:
-
-     --snipped--
-     Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
-     ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
-     Au1xxx IDE(builtin) configured for MWDMA2
-     Probing IDE interface ide0...
-     hda: Maxtor 6E040L0, ATA DISK drive
-     ide0 at 0xac800000-0xac800007,0xac8001c0 on irq 64
-     hda: max request size: 64KiB
-     hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, (U)DMA
-     --snipped--
-
-     In this example 'Maxtor 6E040L0'.
-
-Step  2 : edit 'include/asm-mips/mach-au1x00/au1xxx_ide.h'
-
-  Add your hard disc to the dma_white_list or dma_black_list structur.
-
-Step 3 : Recompile the kernel
-
-  Enable MWDMA support in the kernel configuration. Recompile the kernel and
-  reboot.
-
-Step 4 : Tests
-
-  If you have add a hard disc to the white list, please run some stress tests
-  for verification.
-
 
 ACKNOWLEDGMENTS
 ---------------