PPT Parallel port support is enabled.
PS2 Appropriate PS/2 support is enabled.
RAM RAM disk support is enabled.
+ ROOTPLUG The example Root Plug LSM is enabled.
S390 S390 architecture is enabled.
SCSI Appropriate SCSI support is enabled.
A lot of drivers has their options described inside of
Documentation/scsi/.
+ SECURITY Different security models are enabled.
SELINUX SELinux support is enabled.
SERIAL Serial support is enabled.
SH SuperH architecture is enabled.
Warning: Many of these options can produce a lot of
output and make your system unusable. Be very careful.
-
- acpi_fake_ecdt [HW,ACPI] Workaround failure due to BIOS lacking ECDT
-
acpi_pm_good [X86-32,X86-64]
Override the pmtimer bug detection: force the kernel
to assume that this machine's pmtimer latches its value
apm= [APM] Advanced Power Management
See header of arch/i386/kernel/apm.c.
- applicom= [HW]
- Format: <mem>,<irq>
-
arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
Format: <io>,<irq>,<nodeID>
Format: <io>,<irq>,<mode>
See header of drivers/net/hamradio/baycom_ser_hdx.c.
- blkmtd_device= [HW,MTD]
- blkmtd_erasesz=
- blkmtd_ro=
- blkmtd_bs=
- blkmtd_count=
+ boot_delay= Milliseconds to delay each printk during boot.
+ Values larger than 10 seconds (10000) are changed to
+ no delay (0).
+ Format: integer
bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
bttv.radio= Most important insmod options are available as
possible to determine what the correct size should be.
This option provides an override for these situations.
+ capability.disable=
+ [SECURITY] Disable capabilities. This would normally
+ be used only if an alternative security model is to be
+ configured. Potentially dangerous and should only be
+ used if you are entirely sure of the consequences.
+
chandev= [HW,NET] Generic channel device initialisation
checkreqprot [SELINUX] Set initial checkreqprot flag value.
over the 8254 in addition to over the IO-APIC. The
kernel tries to set a sensible default.
- hpet= [X86-32,HPET] option to disable HPET and use PIT.
- Format: disable
+ hpet= [X86-32,HPET] option to control HPET usage
+ Format: { enable (default) | disable | force }
+ disable: disable HPET and use PIT instead
+ force: allow force enabled of undocumented chips (ICH4,
+ VIA, nVidia)
com20020= [HW,NET] ARCnet - COM20020 chipset
Format:
UART at the specified I/O port or MMIO address.
The options are the same as for ttyS, above.
+ no_console_suspend
+ [HW] Never suspend the console
+ Disable suspending of consoles during suspend and
+ hibernate operations. Once disabled, debugging
+ messages can reach various consoles while the rest
+ of the system is being put to sleep (ie, while
+ debugging driver suspend/resume hooks). This may
+ not work reliably with all consoles, but is known
+ to work with serial and VGA consoles.
+
cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
Format:
<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
[KNL] Reserve a chunk of physical memory to
hold a kernel to switch to with kexec on panic.
+ crashkernel=range1:size1[,range2:size2,...][@offset]
+ [KNL] Same as above, but depends on the memory
+ in the running system. The syntax of range is
+ start-[end] where start and end are both
+ a memory unit (amount[KMG]). See also
+ Documentation/kdump/kdump.txt for a example.
+
cs4232= [HW,OSS]
Format: <io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>
cs89x0_media= [HW,NET]
Format: { rj45 | aui | bnc }
- cyclades= [HW,SERIAL] Cyclades multi-serial port adapter.
-
dasd= [HW,NET]
See header of drivers/s390/block/dasd_devmap.c.
Format: <area>[,<node>]
See also Documentation/networking/decnet.txt.
- default_blu= [VT]
+ vt.default_blu= [VT]
Format: <blue0>,<blue1>,<blue2>,...,<blue15>
Change the default blue palette of the console.
This is a 16-member array composed of values
ranging from 0-255.
- default_grn= [VT]
+ vt.default_grn= [VT]
Format: <green0>,<green1>,<green2>,...,<green15>
Change the default green palette of the console.
This is a 16-member array composed of values
ranging from 0-255.
- default_red= [VT]
+ vt.default_red= [VT]
Format: <red0>,<red1>,<red2>,...,<red15>
Change the default red palette of the console.
This is a 16-member array composed of values
ranging from 0-255.
- default_utf8= [VT]
+ vt.default_utf8=
+ [VT]
Format=<0|1>
Set system-wide default UTF-8 mode for all tty's.
- Default is 0 and by setting to 1, it enables UTF-8
- mode for all newly opened or allocated terminals.
+ Default is 1, i.e. UTF-8 mode is enabled for all
+ newly opened terminals.
dhash_entries= [KNL]
Set number of hash buckets for dentry cache.
See drivers/char/README.epca and
Documentation/digiepca.txt.
- dmascc= [HW,AX25,SERIAL] AX.25 Z80SCC driver with DMA
- support available.
- Format: <io_dev0>[,<io_dev1>[,..<io_dev32>]]
-
dmasound= [HW,OSS] Sound subsystem buffers
dscc4.setup= [NET]
eata= [HW,SCSI]
- ec_intr= [HW,ACPI] ACPI Embedded Controller interrupt mode
- Format: <int>
- 0: polling mode
- non-0: interrupt mode (default)
-
- eda= [HW,PS2]
-
- edb= [HW,PS2]
-
edd= [EDD]
Format: {"of[f]" | "sk[ipmbr]"}
See comment in arch/i386/boot/edd.S
- eicon= [HW,ISDN]
- Format: <id>,<membase>,<irq>
-
eisa_irq_edge= [PARISC,HW]
See header of drivers/parisc/eisa.c.
See Documentation/isdn/README.HiSax.
hugepages= [HW,X86-32,IA-64] Maximal number of HugeTLB pages.
+ hugepagesz= [HW,IA-64,PPC] The size of the HugeTLB pages.
i8042.direct [HW] Put keyboard port into non-translated mode
i8042.dumbkbd [HW] Pretend that controller can only read data from
inttest= [IA64]
+ intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option
+ off
+ Disable intel iommu driver.
+ igfx_off [Default Off]
+ By default, gfx is mapped as normal device. If a gfx
+ device has a dedicated DMAR unit, the DMAR unit is
+ bypassed by not enabling DMAR with this option. In
+ this case, gfx device will use physical address for
+ DMA.
+ forcedac [x86_64]
+ With this option iommu will not optimize to look
+ for io virtual address below 32 bit forcing dual
+ address cycle on pci bus for cards supporting greater
+ than 32 bit addressing. The default is to look
+ for translation below 32 bit and if not available
+ then look in the higher range.
+
io7= [HW] IO7 for Marvel based alpha systems
See comment before marvel_specify_io7 in
arch/alpha/kernel/core_marvel.c.
lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer in
C2 power state.
- lasi= [HW,SCSI] PARISC LASI driver for the 53c700 chip
- Format: addr:<io>,irq:<irq>
+ libata.dma= [LIBATA] DMA control
+ libata.dma=0 Disable all PATA and SATA DMA
+ libata.dma=1 PATA and SATA Disk DMA only
+ libata.dma=2 ATAPI (CDROM) DMA only
+ libata.dma=4 Compact Flash DMA only
+ Combinations also work, so libata.dma=3 enables DMA
+ for disks and CDROMs, but not CFs.
libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
when set.
n must be a power of two. The default size
is set in the kernel config file.
+ logo.nologo [FB] Disables display of the built-in Linux logo.
+ This may be used to provide more screen space for
+ kernel log messages and is useful when debugging
+ kernel boot problems.
+
lp=0 [LP] Specify parallel ports to use, e.g,
lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses
lp=reset first parallel port). 'lp=0' disables the
mce [X86-32] Machine Check Exception
+ mce=option [X86-64] See Documentation/x86_64/boot-options.txt
+
md= [HW] RAID subsystems devices and level
See Documentation/md.txt.
noapic [SMP,APIC] Tells the kernel to not make use of any
IOAPICs that may be present in the system.
- noasync [HW,M68K] Disables async and sync negotiation for
- all devices.
-
nobats [PPC] Do not use BATs for mapping kernel lowmem
on "Classic" PPC cores.
Param: "schedule" - profile schedule points.
Param: <number> - step/bucket size as a power of 2 for
statistical time based profiling.
- Param: "sleep" - profile D-state sleeping (millisecs)
+ Param: "sleep" - profile D-state sleeping (millisecs).
+ Requires CONFIG_SCHEDSTATS
+ Param: "kvm" - profile VM exits.
processor.max_cstate= [HW,ACPI]
Limit processor to maximum C-state
raid= [HW,RAID]
See Documentation/md.txt.
- ramdisk= [RAM] Sizes of RAM disks in kilobytes [deprecated]
- See Documentation/ramdisk.txt.
-
ramdisk_blocksize= [RAM]
See Documentation/ramdisk.txt.
ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
- New name for the ramdisk parameter.
See Documentation/ramdisk.txt.
rcu.blimit= [KNL,BOOT] Set maximum number of finished
Useful for devices that are detected asynchronously
(e.g. USB and MMC devices).
+ root_plug.vendor_id=
+ [ROOTPLUG] Override the default vendor ID
+
+ root_plug.product_id=
+ [ROOTPLUG] Override the default product ID
+
+ root_plug.debug=
+ [ROOTPLUG] Enable debugging output
+
rw [KNL] Mount root device read-write on boot
S [KNL] Run init in single mode
sa1100ir [NET]
See drivers/net/irda/sa1100_ir.c.
- sb= [HW,OSS]
- Format: <io>,<irq>,<dma>,<dma2>
-
sbni= [NET] Granch SBNI12 leased line adapter
sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver
serialnumber [BUGS=X86-32]
- sg_def_reserved_size= [SCSI]
-
shapers= [NET]
Maximal number of shapers.
norandmaps Don't use address space randomization
Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space
- unwind_debug=N N > 0 will enable dwarf2 unwinder debugging
- This is useful to get more information why
- you got a "dwarf2 unwinder stuck"
-
______________________________________________________________________
TODO:
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff