EFI EFI Partitioning (GPT) is enabled
EIDE EIDE/ATAPI support is enabled.
FB The frame buffer device is enabled.
+ GCOV GCOV profiling is enabled.
HW Appropriate hardware is enabled.
IA-64 IA-64 architecture is enabled.
IMA Integrity measurement architecture is enabled.
to assume that this machine's pmtimer latches its value
and always returns good values.
- acpi.power_nocheck= [HW,ACPI]
- Format: 1/0 enable/disable the check of power state.
- On some bogus BIOS the _PSC object/_STA object of
- power resource can't return the correct device power
- state. In such case it is unneccessary to check its
- power state again in power transition.
- 1 : disable the power state check
-
acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
Format: { level | edge | high | low }
Format: off | on
default: on
+ gcov_persist= [GCOV] When non-zero (default), profiling data for
+ kernel modules is saved and remains accessible via
+ debugfs, even when the module is unloaded/reloaded.
+ When zero, profiling data is discarded and associated
+ debugfs files are removed at module unload time.
+
gdth= [HW,SCSI]
See header of drivers/scsi/gdth.c.
nomerge
forcesac
soft
+ pt [x86, IA64]
io7= [HW] IO7 for Marvel based alpha systems
See comment before marvel_specify_io7 in
libata.dma=4 Compact Flash DMA only
Combinations also work, so libata.dma=3 enables DMA
for disks and CDROMs, but not CFs.
+
+ libata.ignore_hpa= [LIBATA] Ignore HPA limit
+ libata.ignore_hpa=0 keep BIOS limits (default)
+ libata.ignore_hpa=1 ignore limits, using full disk
libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
when set.
mtdparts= [MTD]
See drivers/mtd/cmdlinepart.c.
+ onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
+
+ Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
+
+ boundary - index of last SLC block on Flex-OneNAND.
+ The remaining blocks are configured as MLC blocks.
+ lock - Configure if Flex-OneNAND boundary should be locked.
+ Once locked, the boundary cannot be changed.
+ 1 indicates lock status, 0 indicates unlock status.
+
mtdset= [ARM]
ARM/S3C2412 JIVE boot control
[NFS] set the TCP port on which the NFSv4 callback
channel should listen.
+ nfs.cache_getent=
+ [NFS] sets the pathname to the program which is used
+ to update the NFS client cache entries.
+
+ nfs.cache_getent_timeout=
+ [NFS] sets the timeout after which an attempt to
+ update a cache entry is deemed to have failed.
+
nfs.idmap_cache_timeout=
[NFS] set the maximum lifetime for idmapper cache
entries.
oprofile.cpu_type= Force an oprofile cpu type
This might be useful if you have an older oprofile
userland or if you want common events.
- Format: { archperfmon }
- archperfmon: [X86] Force use of architectural
+ Format: { arch_perfmon }
+ arch_perfmon: [X86] Force use of architectural
perfmon on Intel CPUs instead of the
CPU specific event set.
root domains (aka PCI segments, in ACPI-speak).
nommconf [X86] Disable use of MMCONFIG for PCI
Configuration
+ check_enable_amd_mmconf [X86] check for and enable
+ properly configured MMIO access to PCI
+ config space on AMD family 10h CPU
nomsi [MSI] If the PCI_MSI kernel config parameter is
enabled, this kernel boot option can be used to
disable the use of MSI interrupts system-wide.
PAGE_SIZE is used as alignment.
PCI-PCI bridge can be specified, if resource
windows need to be expanded.
+ ecrc= Enable/disable PCIe ECRC (transaction layer
+ end-to-end CRC checking).
+ bios: Use BIOS/firmware settings. This is the
+ the default.
+ off: Turn ECRC off
+ on: Turn ECRC on.
pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
Management.
Format: { 0 | 1 }
See arch/parisc/kernel/pdc_chassis.c
+ percpu_alloc= [X86] Select which percpu first chunk allocator to use.
+ Allowed values are one of "lpage", "embed" and "4k".
+ See comments in arch/x86/kernel/setup_percpu.c for
+ details on each allocator. This parameter is primarily
+ for debugging and performance comparison.
+
pf. [PARIDE]
See Documentation/blockdev/paride.txt.
stifb= [HW]
Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
+ sunrpc.min_resvport=
+ sunrpc.max_resvport=
+ [NFS,SUNRPC]
+ SunRPC servers often require that client requests
+ originate from a privileged port (i.e. a port in the
+ range 0 < portnr < 1024).
+ An administrator who wishes to reserve some of these
+ ports for other uses may adjust the range that the
+ kernel's sunrpc client considers to be privileged
+ using these two parameters to set the minimum and
+ maximum port values.
+
sunrpc.pool_mode=
[NFS]
Control how the NFS server code allocates CPUs to
pernode one pool for each NUMA node (equivalent
to global on non-NUMA machines)
+ sunrpc.tcp_slot_table_entries=
+ sunrpc.udp_slot_table_entries=
+ [NFS,SUNRPC]
+ Sets the upper limit on the number of simultaneous
+ RPC calls that can be sent from the client to a
+ server. Increasing these values may allow you to
+ improve throughput, but will also increase the
+ amount of memory reserved for use by the client.
+
swiotlb= [IA-64] Number of I/O TLB slabs
switches= [HW,M68k]
tp720= [HW,PS2]
- trace_buf_size=nn[KMG] [ftrace] will set tracing buffer size.
+ trace_buf_size=nn[KMG]
+ [FTRACE] will set tracing buffer size.
trix= [HW,OSS] MediaTrix AudioTrix Pro
Format:
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff