EFI EFI Partitioning (GPT) is enabled
EIDE EIDE/ATAPI support is enabled.
FB The frame buffer device is enabled.
+ GCOV GCOV profiling is enabled.
HW Appropriate hardware is enabled.
IA-64 IA-64 architecture is enabled.
IMA Integrity measurement architecture is enabled.
to assume that this machine's pmtimer latches its value
and always returns good values.
- acpi.power_nocheck= [HW,ACPI]
- Format: 1/0 enable/disable the check of power state.
- On some bogus BIOS the _PSC object/_STA object of
- power resource can't return the correct device power
- state. In such case it is unneccessary to check its
- power state again in power transition.
- 1 : disable the power state check
-
acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
Format: { level | edge | high | low }
Also note the kernel might malfunction if you disable
some critical bits.
+ cmo_free_hint= [PPC] Format: { yes | no }
+ Specify whether pages are marked as being inactive
+ when they are freed. This is used in CMO environments
+ to determine OS memory pressure for page stealing by
+ a hypervisor.
+ Default: yes
+
code_bytes [X86] How many bytes of object code to print
in an oops report.
Range: 0 - 8192
console=brl,ttyS0
For now, only VisioBraille is supported.
+ consoleblank= [KNL] The console blank (screen saver) timeout in
+ seconds. Defaults to 10*60 = 10mins. A value of 0
+ disables the blank timer.
+
coredump_filter=
[KNL] Change the default value for
/proc/<pid>/coredump_filter.
Format: off | on
default: on
+ gcov_persist= [GCOV] When non-zero (default), profiling data for
+ kernel modules is saved and remains accessible via
+ debugfs, even when the module is unloaded/reloaded.
+ When zero, profiling data is discarded and associated
+ debugfs files are removed at module unload time.
+
gdth= [HW,SCSI]
See header of drivers/scsi/gdth.c.
ide-core.nodma= [HW] (E)IDE subsystem
Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
- .vlb_clock .pci_clock .noflush .noprobe .nowerr .cdrom
- .chs .ignore_cable are additional options
- See Documentation/ide/ide.txt.
-
- idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed
+ .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr
+ .cdrom .chs .ignore_cable are additional options
See Documentation/ide/ide.txt.
ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
nomerge
forcesac
soft
+ pt [x86, IA64]
io7= [HW] IO7 for Marvel based alpha systems
See comment before marvel_specify_io7 in
libata.dma=4 Compact Flash DMA only
Combinations also work, so libata.dma=3 enables DMA
for disks and CDROMs, but not CFs.
+
+ libata.ignore_hpa= [LIBATA] Ignore HPA limit
+ libata.ignore_hpa=0 keep BIOS limits (default)
+ libata.ignore_hpa=1 ignore limits, using full disk
libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
when set.
min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
physical address is ignored.
+ mini2440= [ARM,HW,KNL]
+ Format:[0..2][b][c][t]
+ Default: "0tb"
+ MINI2440 configuration specification:
+ 0 - The attached screen is the 3.5" TFT
+ 1 - The attached screen is the 7" TFT
+ 2 - The VGA Shield is attached (1024x768)
+ Leaving out the screen size parameter will not load
+ the TFT driver, and the framebuffer will be left
+ unconfigured.
+ b - Enable backlight. The TFT backlight pin will be
+ linked to the kernel VESA blanking code and a GPIO
+ LED. This parameter is not necessary when using the
+ VGA shield.
+ c - Enable the s3c camera interface.
+ t - Reserved for enabling touchscreen support. The
+ touchscreen support is not enabled in the mainstream
+ kernel as of 2.6.30, a preliminary port can be found
+ in the "bleeding edge" mini2440 support kernel at
+ http://repo.or.cz/w/linux-2.6/mini2440.git
+
mminit_loglevel=
[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
parameter allows control of the logging verbosity for
mtdparts= [MTD]
See drivers/mtd/cmdlinepart.c.
+ onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
+
+ Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
+
+ boundary - index of last SLC block on Flex-OneNAND.
+ The remaining blocks are configured as MLC blocks.
+ lock - Configure if Flex-OneNAND boundary should be locked.
+ Once locked, the boundary cannot be changed.
+ 1 indicates lock status, 0 indicates unlock status.
+
mtdset= [ARM]
ARM/S3C2412 JIVE boot control
oprofile.cpu_type= Force an oprofile cpu type
This might be useful if you have an older oprofile
userland or if you want common events.
- Format: { archperfmon }
- archperfmon: [X86] Force use of architectural
+ Format: { arch_perfmon }
+ arch_perfmon: [X86] Force use of architectural
perfmon on Intel CPUs instead of the
CPU specific event set.
root domains (aka PCI segments, in ACPI-speak).
nommconf [X86] Disable use of MMCONFIG for PCI
Configuration
+ check_enable_amd_mmconf [X86] check for and enable
+ properly configured MMIO access to PCI
+ config space on AMD family 10h CPU
nomsi [MSI] If the PCI_MSI kernel config parameter is
enabled, this kernel boot option can be used to
disable the use of MSI interrupts system-wide.
PAGE_SIZE is used as alignment.
PCI-PCI bridge can be specified, if resource
windows need to be expanded.
+ ecrc= Enable/disable PCIe ECRC (transaction layer
+ end-to-end CRC checking).
+ bios: Use BIOS/firmware settings. This is the
+ the default.
+ off: Turn ECRC off
+ on: Turn ECRC on.
pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
Management.
Format: { 0 | 1 }
See arch/parisc/kernel/pdc_chassis.c
+ percpu_alloc= [X86] Select which percpu first chunk allocator to use.
+ Allowed values are one of "lpage", "embed" and "4k".
+ See comments in arch/x86/kernel/setup_percpu.c for
+ details on each allocator. This parameter is primarily
+ for debugging and performance comparison.
+
pf. [PARIDE]
See Documentation/blockdev/paride.txt.
tp720= [HW,PS2]
- trace_buf_size=nn[KMG] [ftrace] will set tracing buffer size.
+ trace_buf_size=nn[KMG]
+ [FTRACE] will set tracing buffer size.
+
+ trace_event=[event-list]
+ [FTRACE] Set and start specified trace events in order
+ to facilitate early boot debugging.
+ See also Documentation/trace/events.txt
trix= [HW,OSS] MediaTrix AudioTrix Pro
Format:
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff