ixgbe: Improve reset coordination between the PF and the VF

[safe/jmp/linux-2.6] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 777dc8a..736d456 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -240,7 +240,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
        acpi_sleep=     [HW,ACPI] Sleep options
                        Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
-                                 old_ordering, s4_nonvs }
+                                 old_ordering, s4_nonvs, sci_force_enable }
                        See Documentation/power/video.txt for information on
                        s3_bios and s3_mode.
                        s3_beep is for debugging; it makes the PC's speaker beep
@@ -253,6 +253,9 @@ and is between 256 and 4096 characters. It is defined in the file
                        of _PTS is used by default).
                        s4_nonvs prevents the kernel from saving/restoring the
                        ACPI NVS memory during hibernation.
+                       sci_force_enable causes the kernel to set SCI_EN directly
+                       on resume from S1/S3 (which is against the ACPI spec,
+                       but some broken systems don't work without it).
 
        acpi_use_timer_override [HW,ACPI]
                        Use timer override. For some broken Nvidia NF5 boards
@@ -1032,7 +1035,7 @@ and is between 256 and 4096 characters. It is defined in the file
                        No delay
 
        ip=             [IP_PNP]
-                       See Documentation/filesystems/nfsroot.txt.
+                       See Documentation/filesystems/nfs/nfsroot.txt.
 
        ip2=            [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
                        See comment before ip2_setup() in
@@ -1553,10 +1556,10 @@ and is between 256 and 4096 characters. It is defined in the file
                        going to be removed in 2.6.29.
 
        nfsaddrs=       [NFS]
-                       See Documentation/filesystems/nfsroot.txt.
+                       See Documentation/filesystems/nfs/nfsroot.txt.
 
        nfsroot=        [NFS] nfs root filesystem for disk-less boxes.
-                       See Documentation/filesystems/nfsroot.txt.
+                       See Documentation/filesystems/nfs/nfsroot.txt.
 
        nfs.callback_tcpport=
                        [NFS] set the TCP port on which the NFSv4 callback
@@ -1787,6 +1790,11 @@ and is between 256 and 4096 characters. It is defined in the file
                        waiting for the ACK, so if this is set too high
                        interrupts *may* be lost!
 
+       omap_mux=       [OMAP] Override bootloader pin multiplexing.
+                       Format: <mux_mode0.mode_name=value>...
+                       For example, to override I2C bus2:
+                       omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
+
        opl3=           [HW,OSS]
                        Format: <io>
 
@@ -2663,6 +2671,8 @@ and is between 256 and 4096 characters. It is defined in the file
                        to a common usb-storage quirk flag as follows:
                                a = SANE_SENSE (collect more than 18 bytes
                                        of sense data);
+                               b = BAD_SENSE (don't collect more than 18
+                                       bytes of sense data);
                                c = FIX_CAPACITY (decrease the reported
                                        device capacity by one sector);
                                h = CAPACITY_HEURISTICS (decrease the
@@ -2722,6 +2732,11 @@ and is between 256 and 4096 characters. It is defined in the file
        vmpoff=         [KNL,S390] Perform z/VM CP command after power off.
                        Format: <command>
 
+       vt.cur_default= [VT] Default cursor shape.
+                       Format: 0xCCBBAA, where AA, BB, and CC are the same as
+                       the parameters of the <Esc>[?A;B;Cc escape sequence;
+                       see VGA-softcursor.txt. Default: 2 = underline.
+
        vt.default_blu= [VT]
                        Format: <blue0>,<blue1>,<blue2>,...,<blue15>
                        Change the default blue palette of the console.