acpi_sleep= [HW,ACPI] Sleep options
Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
- old_ordering, s4_nonvs }
+ old_ordering, s4_nonvs, sci_force_enable }
See Documentation/power/video.txt for information on
s3_bios and s3_mode.
s3_beep is for debugging; it makes the PC's speaker beep
of _PTS is used by default).
s4_nonvs prevents the kernel from saving/restoring the
ACPI NVS memory during hibernation.
+ sci_force_enable causes the kernel to set SCI_EN directly
+ on resume from S1/S3 (which is against the ACPI spec,
+ but some broken systems don't work without it).
acpi_use_timer_override [HW,ACPI]
Use timer override. For some broken Nvidia NF5 boards
Change the amount of debugging information output
when initialising the APIC and IO-APIC components.
+ show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller
+ Limit apic dumping. The parameter defines the maximal
+ number of local apics being dumped. Also it is possible
+ to set it to "all" by meaning -- no limit here.
+ Format: { 1 (default) | 2 | ... | all }.
+ The parameter valid if only apic=debug or
+ apic=verbose is specified.
+ Example: apic=debug show_lapic=all
+
apm= [APM] Advanced Power Management
See header of arch/x86/kernel/apm_32.c.
No delay
ip= [IP_PNP]
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
See comment before ip2_setup() in
going to be removed in 2.6.29.
nfsaddrs= [NFS]
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
nfsroot= [NFS] nfs root filesystem for disk-less boxes.
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
nfs.callback_tcpport=
[NFS] set the TCP port on which the NFSv4 callback
waiting for the ACK, so if this is set too high
interrupts *may* be lost!
+ omap_mux= [OMAP] Override bootloader pin multiplexing.
+ Format: <mux_mode0.mode_name=value>...
+ For example, to override I2C bus2:
+ omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
+
opl3= [HW,OSS]
Format: <io>
sbni= [NET] Granch SBNI12 leased line adapter
+ sched_debug [KNL] Enables verbose scheduler debug messages.
+
sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver
Format: <io>[,<timeout>[,<isapnp>]]
to a common usb-storage quirk flag as follows:
a = SANE_SENSE (collect more than 18 bytes
of sense data);
+ b = BAD_SENSE (don't collect more than 18
+ bytes of sense data);
c = FIX_CAPACITY (decrease the reported
device capacity by one sector);
h = CAPACITY_HEURISTICS (decrease the
vmpoff= [KNL,S390] Perform z/VM CP command after power off.
Format: <command>
+ vt.cur_default= [VT] Default cursor shape.
+ Format: 0xCCBBAA, where AA, BB, and CC are the same as
+ the parameters of the <Esc>[?A;B;Cc escape sequence;
+ see VGA-softcursor.txt. Default: 2 = underline.
+
vt.default_blu= [VT]
Format: <blue0>,<blue1>,<blue2>,...,<blue15>
Change the default blue palette of the console.
Default is 1, i.e. UTF-8 mode is enabled for all
newly opened terminals.
+ vt.global_cursor_default=
+ [VT]
+ Format=<-1|0|1>
+ Set system-wide default for whether a cursor
+ is shown on new VTs. Default is -1,
+ i.e. cursors will be created by default unless
+ overridden by individual drivers. 0 will hide
+ cursors, 1 will display them.
+
waveartist= [HW,OSS]
Format: <io>,<irq>,<dma>,<dma2>