ISAPNP ISA PnP code is enabled.
ISDN Appropriate ISDN support is enabled.
JOY Appropriate joystick support is enabled.
+ LIBATA Libata driver is enabled
LP Printer support is enabled.
LOOP Loopback device support is enabled.
M68k M68k architecture is enabled.
GENERIC_TIME The generic timeofday code is enabled.
NFS Appropriate NFS support is enabled.
OSS OSS sound support is enabled.
+ PV_OPS A paravirtualized kernel
PARIDE The ParIDE subsystem is enabled.
PARISC The PA-RISC architecture is enabled.
PCI PCI bus support is enabled.
Documentation/scsi/.
SELINUX SELinux support is enabled.
SERIAL Serial support is enabled.
+ SH SuperH architecture is enabled.
SMP The kernel is an SMP kernel.
SPARC Sparc architecture is enabled.
SWSUSP Software suspend is enabled.
See header of drivers/scsi/53c7xx.c.
See also Documentation/scsi/ncr53c7xx.txt.
- acpi= [HW,ACPI] Advanced Configuration and Power Interface
+ acpi= [HW,ACPI,X86-64,i386]
+ Advanced Configuration and Power Interface
Format: { force | off | ht | strict | noirq }
force -- enable ACPI if default was off
off -- disable ACPI if default was on
See also Documentation/pm.txt, pci=noacpi
+ acpi_apic_instance= [ACPI, IOAPIC]
+ Format: <int>
+ 2: use 2nd APIC table, if available
+ 1,0: use 1st APIC table
+ default: 0
+
acpi_sleep= [HW,ACPI] Sleep options
Format: { s3_bios, s3_mode }
See Documentation/power/video.txt
that require a timer override, but don't have
HPET
- acpi_dbg_layer= [HW,ACPI]
+ acpi.debug_layer= [HW,ACPI]
Format: <int>
Each bit of the <int> indicates an ACPI debug layer,
1: enable, 0: disable. It is useful for boot time
debugging. After system has booted up, it can be set
- via /proc/acpi/debug_layer.
-
- acpi_dbg_level= [HW,ACPI]
+ via /sys/module/acpi/parameters/debug_layer.
+ CONFIG_ACPI_DEBUG must be enabled for this to produce any output.
+ Available bits (add the numbers together) to enable debug output
+ for specific parts of the ACPI subsystem:
+ 0x01 utilities 0x02 hardware 0x04 events 0x08 tables
+ 0x10 namespace 0x20 parser 0x40 dispatcher
+ 0x80 executer 0x100 resources 0x200 acpica debugger
+ 0x400 os services 0x800 acpica disassembler.
+ The number can be in decimal or prefixed with 0x in hex.
+ Warning: Many of these options can produce a lot of
+ output and make your system unusable. Be very careful.
+
+ acpi.debug_level= [HW,ACPI]
Format: <int>
Each bit of the <int> indicates an ACPI debug level,
1: enable, 0: disable. It is useful for boot time
debugging. After system has booted up, it can be set
- via /proc/acpi/debug_level.
+ via /sys/module/acpi/parameters/debug_level.
+ CONFIG_ACPI_DEBUG must be enabled for this to produce any output.
+ Available bits (add the numbers together) to enable different
+ debug output levels of the ACPI subsystem:
+ 0x01 error 0x02 warn 0x04 init 0x08 debug object
+ 0x10 info 0x20 init names 0x40 parse 0x80 load
+ 0x100 dispatch 0x200 execute 0x400 names 0x800 operation region
+ 0x1000 bfield 0x2000 tables 0x4000 values 0x8000 objects
+ 0x10000 resources 0x20000 user requests 0x40000 package.
+ The number can be in decimal or prefixed with 0x in hex.
+ Warning: Many of these options can produce a lot of
+ output and make your system unusable. Be very careful.
+
acpi_fake_ecdt [HW,ACPI] Workaround failure due to BIOS lacking ECDT
Format: <area>[,<node>]
See also Documentation/networking/decnet.txt.
+ default_blu= [VT]
+ Format: <blue0>,<blue1>,<blue2>,...,<blue15>
+ Change the default blue palette of the console.
+ This is a 16-member array composed of values
+ ranging from 0-255.
+
+ default_grn= [VT]
+ Format: <green0>,<green1>,<green2>,...,<green15>
+ Change the default green palette of the console.
+ This is a 16-member array composed of values
+ ranging from 0-255.
+
+ default_red= [VT]
+ Format: <red0>,<red1>,<red2>,...,<red15>
+ Change the default red palette of the console.
+ This is a 16-member array composed of values
+ ranging from 0-255.
+
+ default_utf8= [VT]
+ Format=<0|1>
+ Set system-wide default UTF-8 mode for all tty's.
+ Default is 0 and by setting to 1, it enables UTF-8
+ mode for all newly opened or allocated terminals.
+
dhash_entries= [KNL]
Set number of hash buckets for dentry cache.
dtc3181e= [HW,SCSI]
- earlyprintk= [IA-32,X86-64]
+ earlyprintk= [IA-32,X86-64,SH]
earlyprintk=vga
earlyprintk=serial[,ttySn[,baudrate]]
idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed
See Documentation/ide.txt.
- idle= [HW]
- Format: idle=poll or idle=halt
+ idle= [X86]
+ Format: idle=poll or idle=mwait
+ Poll forces a polling idle loop that can slightly improves the performance
+ of waking up a idle CPU, but will use a lot of power and make the system
+ run hot. Not recommended.
+ idle=mwait. On systems which support MONITOR/MWAIT but the kernel chose
+ to not use it because it doesn't save as much power as a normal idle
+ loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same
+ as idle=poll.
ignore_loglevel [KNL]
Ignore loglevel setting - this will print /all/
inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
Format: <irq>
- combined_mode= [HW] control which driver uses IDE ports in combined
- mode: legacy IDE driver, libata, or both
- (in the libata case, libata.atapi_enabled=1 may be
- useful as well). Note that using the ide or libata
- options may affect your device naming (e.g. by
- changing hdc to sdb).
- Format: combined (default), ide, or libata
-
inttest= [IA64]
io7= [HW] IO7 for Marvel based alpha systems
lapic [IA-32,APIC] Enable the local APIC even if BIOS
disabled it.
+ lapic_timer_c2_ok [IA-32,x86-64,APIC] trust the local apic timer in
+ C2 power state.
+
lasi= [HW,SCSI] PARISC LASI driver for the 53c700 chip
Format: addr:<io>,irq:<irq>
+ legacy_serial.force [HW,IA-32,X86-64]
+ Probe for COM ports at legacy addresses even
+ if PNPBIOS or ACPI should describe them. This
+ is for working around firmware defects.
+
llsc*= [IA64] See function print_params() in
arch/ia64/sn/kernel/llsc4.c.
Format: <1-256>
maxcpus= [SMP] Maximum number of processors that an SMP kernel
- should make use of
+ should make use of.
+ Using "nosmp" or "maxcpus=0" will disable SMP
+ entirely (the MPS table probe still happens, though).
+ A command-line option of "maxcpus=<NUM>", where <NUM>
+ is an integer greater than 0, limits the maximum number
+ of CPUs activated in SMP mode to <NUM>.
+ Using "maxcpus=1" on an SMP kernel is the trivial
+ case of an SMP kernel with only one CPU.
max_addr=[KMG] [KNL,BOOT,ia64] All physical memory greater than or
equal to this physical address is ignored.
emulation library even if a 387 maths coprocessor
is present.
+ noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
+ when set.
+ Format: <int>
+
noaliencache [MM, NUMA] Disables the allcoation of alien caches in
the slab allocator. Saves per-node memory, but will
impact performance on real NUMA hardware.
nolapic [IA-32,APIC] Do not enable or use the local APIC.
+ nolapic_timer [IA-32,APIC] Do not use the local APIC timer.
+
noltlbs [PPC] Do not use large page/tlb entries for kernel
lowmem mapping on PPC40x.
nomce [IA-32] Machine Check Exception
+ noreplace-paravirt [IA-32,PV_OPS] Don't patch paravirt_ops
+
+ noreplace-smp [IA-32,SMP] Don't replace SMP instructions
+ with UP alternatives
+
noresidual [PPC] Don't use residual data on PReP machines.
noresume [SWSUSP] Disables resume and restores original swap
This sorting is done to get a device
order compatible with older (<= 2.4) kernels.
nobfsort Don't sort PCI devices into breadth-first order.
+ cbiosize=nn[KMG] The fixed amount of bus space which is
+ reserved for the CardBus bridge's IO window.
+ The default value is 256 bytes.
+ cbmemsize=nn[KMG] The fixed amount of bus space which is
+ reserved for the CardBus bridge's memory
+ window. The default value is 64 megabytes.
pcmv= [HW,PCMCIA] BadgePAD 4
smart2= [HW]
Format: <io1>[,<io2>[,...,<io8>]]
+ smp-alt-once [IA-32,SMP] On a hotplug CPU system, only
+ attempt to substitute SMP alternatives once at boot.
+
+ smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices
+ smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port
+ smsc-ircc2.ircc_sir= [HW] SIR base I/O port
+ smsc-ircc2.ircc_fir= [HW] FIR base I/O port
+ smsc-ircc2.ircc_irq= [HW] IRQ line
+ smsc-ircc2.ircc_dma= [HW] DMA channel
+ smsc-ircc2.ircc_transceiver= [HW] Transceiver type:
+ 0: Toshiba Satellite 1800 (GP data pin select)
+ 1: Fast pin select (default)
+ 2: ATC IRMode
+
snd-ad1816a= [HW,ALSA]
snd-ad1848= [HW,ALSA]
stifb= [HW]
Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
+ sunrpc.pool_mode=
+ [NFS]
+ Control how the NFS server code allocates CPUs to
+ service thread pools. Depending on how many NICs
+ you have and where their interrupts are bound, this
+ option will affect which CPUs will do NFS serving.
+ Note: this parameter cannot be changed while the
+ NFS server is running.
+
+ auto the server chooses an appropriate mode
+ automatically using heuristics
+ global a single global pool contains all CPUs
+ percpu one pool for each CPU
+ pernode one pool for each NUMA node (equivalent
+ to global on non-NUMA machines)
+
swiotlb= [IA-64] Number of I/O TLB slabs
switches= [HW,M68k]
Note that genuine overcurrent events won't be
reported either.
+ usbcore.autosuspend=
+ [USB] The autosuspend time delay (in seconds) used
+ for newly-detected USB devices (default 2). This
+ is the time required before an idle device will be
+ autosuspended. Devices for which the delay is set
+ to a negative value won't be autosuspended at all.
+
usbhid.mousepoll=
[USBHID] The interval which mice are to be polled at.
- vdso= [IA-32]
+ vdso= [IA-32,SH]
+ vdso=2: enable compat VDSO (default with COMPAT_VDSO)
vdso=1: enable VDSO (default)
vdso=0: disable VDSO mapping
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff