* Winbond W83791D
Prefix: 'w83791d'
Addresses scanned: I2C 0x2c - 0x2f
- Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791Da.pdf
+ Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791D_W83791Gb.pdf
Author: Charles Spirakis <bezaur@gmail.com>
and Mark Studebaker <mdsxyz123@yahoo.com>
w83792d.c:
Chunhao Huang <DZShen@Winbond.com.tw>,
- Rudolf Marek <r.marek@sh.cvut.cz>
+ Rudolf Marek <r.marek@assembler.cz>
+
+Additional contributors:
+ Sven Anders <anders@anduras.de>
+ Marc Hulsman <m.hulsman@tudelft.nl>
Module Parameters
-----------------
Description
-----------
-This driver implements support for the Winbond W83791D chip.
+This driver implements support for the Winbond W83791D chip. The W83791G
+chip appears to be the same as the W83791D but is lead free.
Detection of the chip can sometimes be foiled because it can be in an
internal state that allows no clean access (Bank with ID register is not
currently selected). If you know the address of the chip, use a 'force'
parameter; this will put it into a more well-behaved state first.
-The driver implements three temperature sensors, five fan rotation speed
-sensors, and ten voltage sensors.
+The driver implements three temperature sensors, ten voltage sensors,
+five fan rotation speed sensors and manual PWM control of each fan.
Temperatures are measured in degrees Celsius and measurement resolution is 1
degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
the temperature gets higher than the Overtemperature Shutdown value; it stays
on until the temperature falls below the Hysteresis value.
-Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
-triggered if the rotation speed has dropped below a programmable limit. Fan
-readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3
-and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more
-range or accuracy.
-
Voltage sensors (also known as IN sensors) report their values in millivolts.
An alarm is triggered if the voltage has crossed a programmable minimum
or maximum limit.
-Alarms are provided as output from a "realtime status register". The
-following bits are defined:
-
-bit - alarm on:
-0 - Vcore
-1 - VINR0
-2 - +3.3VIN
-3 - 5VDD
-4 - temp1
-5 - temp2
-6 - fan1
-7 - fan2
-8 - +12VIN
-9 - -12VIN
-10 - -5VIN
-11 - fan3
-12 - chassis
-13 - temp3
-14 - VINR1
-15 - reserved
-16 - tart1
-17 - tart2
-18 - tart3
-19 - VSB
-20 - VBAT
-21 - fan4
-22 - fan5
-23 - reserved
-
-When an alarm goes off, you can be warned by a beeping signal through your
-computer speaker. It is possible to enable all beeping globally, or only
-the beeping for some alarms.
-
-The driver only reads the chip values each 3 seconds; reading them more
-often will do no harm, but will return 'old' values.
-
-W83791D TODO:
----------------
-Provide a patch for per-file alarms as discussed on the mailing list
-Provide a patch for smart-fan control (still need appropriate motherboard/fans)
+Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
+triggered if the rotation speed has dropped below a programmable limit. Fan
+readings can be divided by a programmable divider (1, 2, 4, 8, 16,
+32, 64 or 128 for all fans) to give the readings more range or accuracy.
+
+Each fan controlled is controlled by PWM. The PWM duty cycle can be read and
+set for each fan separately. Valid values range from 0 (stop) to 255 (full).
+PWM 1-3 support Thermal Cruise mode, in which the PWMs are automatically
+regulated to keep respectively temp 1-3 at a certain target temperature.
+See below for the description of the sysfs-interface.
+
+The w83791d has a global bit used to enable beeping from the speaker when an
+alarm is triggered as well as a bitmask to enable or disable the beep for
+specific alarms. You need both the global beep enable bit and the
+corresponding beep bit to be on for a triggered alarm to sound a beep.
+
+The sysfs interface to the global enable is via the sysfs beep_enable file.
+This file is used for both legacy and new code.
+
+The sysfs interface to the beep bitmask has migrated from the original legacy
+method of a single sysfs beep_mask file to a newer method using multiple
+*_beep files as described in .../Documentation/hwmon/sysfs-interface.
+
+A similar change has occured for the bitmap corresponding to the alarms. The
+original legacy method used a single sysfs alarms file containing a bitmap
+of triggered alarms. The newer method uses multiple sysfs *_alarm files
+(again following the pattern described in sysfs-interface).
+
+Since both methods read and write the underlying hardware, they can be used
+interchangeably and changes in one will automatically be reflected by
+the other. If you use the legacy bitmask method, your user-space code is
+responsible for handling the fact that the alarms and beep_mask bitmaps
+are not the same (see the table below).
+
+NOTE: All new code should be written to use the newer sysfs-interface
+specification as that avoids bitmap problems and is the preferred interface
+going forward.
+
+The driver reads the hardware chip values at most once every three seconds.
+User mode code requesting values more often will receive cached values.
+
+/sys files
+----------
+The sysfs-interface is documented in the 'sysfs-interface' file. Only
+chip-specific options are documented here.
+
+pwm[1-3]_enable - this file controls mode of fan/temperature control for
+ fan 1-3. Fan/PWM 4-5 only support manual mode.
+ * 1 Manual mode
+ * 2 Thermal Cruise mode
+ * 3 Fan Speed Cruise mode (no further support)
+
+temp[1-3]_target - defines the target temperature for Thermal Cruise mode.
+ Unit: millidegree Celsius
+ RW
+
+temp[1-3]_tolerance - temperature tolerance for Thermal Cruise mode.
+ Specifies an interval around the target temperature
+ in which the fan speed is not changed.
+ Unit: millidegree Celsius
+ RW
+
+Alarms bitmap vs. beep_mask bitmask
+------------------------------------
+For legacy code using the alarms and beep_mask files:
+
+in0 (VCORE) : alarms: 0x000001 beep_mask: 0x000001
+in1 (VINR0) : alarms: 0x000002 beep_mask: 0x002000 <== mismatch
+in2 (+3.3VIN): alarms: 0x000004 beep_mask: 0x000004
+in3 (5VDD) : alarms: 0x000008 beep_mask: 0x000008
+in4 (+12VIN) : alarms: 0x000100 beep_mask: 0x000100
+in5 (-12VIN) : alarms: 0x000200 beep_mask: 0x000200
+in6 (-5VIN) : alarms: 0x000400 beep_mask: 0x000400
+in7 (VSB) : alarms: 0x080000 beep_mask: 0x010000 <== mismatch
+in8 (VBAT) : alarms: 0x100000 beep_mask: 0x020000 <== mismatch
+in9 (VINR1) : alarms: 0x004000 beep_mask: 0x004000
+temp1 : alarms: 0x000010 beep_mask: 0x000010
+temp2 : alarms: 0x000020 beep_mask: 0x000020
+temp3 : alarms: 0x002000 beep_mask: 0x000002 <== mismatch
+fan1 : alarms: 0x000040 beep_mask: 0x000040
+fan2 : alarms: 0x000080 beep_mask: 0x000080
+fan3 : alarms: 0x000800 beep_mask: 0x000800
+fan4 : alarms: 0x200000 beep_mask: 0x200000
+fan5 : alarms: 0x400000 beep_mask: 0x400000
+tart1 : alarms: 0x010000 beep_mask: 0x040000 <== mismatch
+tart2 : alarms: 0x020000 beep_mask: 0x080000 <== mismatch
+tart3 : alarms: 0x040000 beep_mask: 0x100000 <== mismatch
+case_open : alarms: 0x001000 beep_mask: 0x001000
+global_enable: alarms: -------- beep_mask: 0x800000 (modified via beep_enable)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff