---------------------------
-What: /sys/devices/.../power/state
- dev->power.power_state
- dpm_runtime_{suspend,resume)()
+What: MXSER
+When: December 2007
+Why: Old mxser driver is obsoleted by the mxser_new. Give it some time yet
+ and remove it.
+Who: Jiri Slaby <jirislaby@gmail.com>
+
+---------------------------
+
+What: V4L2 VIDIOC_G_MPEGCOMP and VIDIOC_S_MPEGCOMP
+When: October 2007
+Why: Broken attempt to set MPEG compression parameters. These ioctls are
+ not able to implement the wide variety of parameters that can be set
+ by hardware MPEG encoders. A new MPEG control mechanism was created
+ in kernel 2.6.18 that replaces these ioctls. See the V4L2 specification
+ (section 1.9: Extended controls) for more information on this topic.
+Who: Hans Verkuil <hverkuil@xs4all.nl> and
+ Mauro Carvalho Chehab <mchehab@infradead.org>
+
+---------------------------
+
+What: dev->power.power_state
When: July 2007
Why: Broken design for runtime control over driver power states, confusing
driver-internal runtime power management with: mechanisms to support
---------------------------
-What: RAW driver (CONFIG_RAW_DRIVER)
-When: December 2005
-Why: declared obsolete since kernel 2.6.3
- O_DIRECT can be used instead
-Who: Adrian Bunk <bunk@stusta.de>
-
----------------------------
-
-What: raw1394: requests of type RAW1394_REQ_ISO_SEND, RAW1394_REQ_ISO_LISTEN
-When: June 2007
-Why: Deprecated in favour of the more efficient and robust rawiso interface.
- Affected are applications which use the deprecated part of libraw1394
- (raw1394_iso_write, raw1394_start_iso_write, raw1394_start_iso_rcv,
- raw1394_stop_iso_rcv) or bypass libraw1394.
-Who: Dan Dennedy <dan@dennedy.org>, Stefan Richter <stefanr@s5r6.in-berlin.de>
-
----------------------------
-
-What: dv1394 driver (CONFIG_IEEE1394_DV1394)
-When: June 2007
-Why: Replaced by raw1394 + userspace libraries, notably libiec61883. This
- shift of application support has been indicated on www.linux1394.org
- and developers' mailinglists for quite some time. Major applications
- have been converted, with the exception of ffmpeg and hence xine.
- Piped output of dvgrab2 is a partial equivalent to dv1394.
-Who: Dan Dennedy <dan@dennedy.org>, Stefan Richter <stefanr@s5r6.in-berlin.de>
+What: old NCR53C9x driver
+When: October 2007
+Why: Replaced by the much better esp_scsi driver. Actual low-level
+ driver can be ported over almost trivially.
+Who: David Miller <davem@davemloft.net>
+ Christoph Hellwig <hch@lst.de>
---------------------------
What: Video4Linux API 1 ioctls and video_decoder.h from Video devices.
When: December 2006
+Files: include/linux/video_decoder.h
+Check: include/linux/video_decoder.h
Why: V4L1 AP1 was replaced by V4L2 API. during migration from 2.4 to 2.6
series. The old API have lots of drawbacks and don't provide enough
means to work with all video and audio standards. The newer API is
What: remove EXPORT_SYMBOL(kernel_thread)
When: August 2006
Files: arch/*/kernel/*_ksyms.c
+Check: kernel_thread
Why: kernel_thread is a low-level implementation detail. Drivers should
use the <linux/kthread.h> API instead which shields them from
implementation details and provides a higherlevel interface that
---------------------------
-What: drivers depending on OSS_OBSOLETE_DRIVER
-When: options in 2.6.20, code in 2.6.22
-Why: OSS drivers with ALSA replacements
-Who: Adrian Bunk <bunk@stusta.de>
-
----------------------------
-
-What: pci_module_init(driver)
-When: January 2007
-Why: Is replaced by pci_register_driver(pci_driver).
-Who: Richard Knutsson <ricknu-0@student.ltu.se> and Greg Kroah-Hartman <gregkh@suse.de>
-
----------------------------
-
-What: Usage of invalid timevals in setitimer
-When: March 2007
-Why: POSIX requires to validate timevals in the setitimer call. This
- was never done by Linux. The invalid (e.g. negative timevals) were
- silently converted to more or less random timeouts and intervals.
- Until the removal a per boot limited number of warnings is printed
- and the timevals are sanitized.
-
-Who: Thomas Gleixner <tglx@linutronix.de>
-
----------------------------
-
What: Unused EXPORT_SYMBOL/EXPORT_SYMBOL_GPL exports
(temporary transition config option provided until then)
The transition config option will also be removed at the same time.
---------------------------
-What: mount/umount uevents
-When: February 2007
-Why: These events are not correct, and do not properly let userspace know
- when a file system has been mounted or unmounted. Userspace should
- poll the /proc/mounts file instead to detect this properly.
-Who: Greg Kroah-Hartman <gregkh@suse.de>
-
----------------------------
-
What: USB driver API moves to EXPORT_SYMBOL_GPL
When: February 2008
Files: include/linux/usb.h, drivers/usb/core/driver.c
---------------------------
+What: vm_ops.nopage
+When: Soon, provided in-kernel callers have been converted
+Why: This interface is replaced by vm_ops.fault, but it has been around
+ forever, is used by a lot of drivers, and doesn't cost much to
+ maintain.
+Who: Nick Piggin <npiggin@suse.de>
+
+---------------------------
+
What: Interrupt only SA_* flags
-When: Januar 2007
+When: September 2007
Why: The interrupt related SA_* flags are replaced by IRQF_* to move them
out of the signal namespace.
---------------------------
-What: i2c-isa
-When: December 2006
-Why: i2c-isa is a non-sense and doesn't fit in the device driver
- model. Drivers relying on it are better implemented as platform
- drivers.
-Who: Jean Delvare <khali@linux-fr.org>
-
----------------------------
-
-What: i2c_adapter.dev
- i2c_adapter.list
+What: i2c_adapter.list
When: July 2007
-Why: Superfluous, given i2c_adapter.class_dev:
- * The "dev" was a stand-in for the physical device node that legacy
- drivers would not have; but now it's almost always present. Any
- remaining legacy drivers must upgrade (they now trigger warnings).
- * The "list" duplicates class device children.
- The delay in removing this is so upgraded lm_sensors and libsensors
- can get deployed. (Removal causes minor changes in the sysfs layout,
- notably the location of the adapter type name and parenting the i2c
- client hardware directly from their controller.)
+Why: Superfluous, this list duplicates the one maintained by the driver
+ core.
Who: Jean Delvare <khali@linux-fr.org>,
David Brownell <dbrownell@users.sourceforge.net>
---------------------------
-What: IPv4 only connection tracking/NAT/helpers
-When: 2.6.22
-Why: The new layer 3 independant connection tracking replaces the old
- IPv4 only version. After some stabilization of the new code the
- old one will be removed.
-Who: Patrick McHardy <kaber@trash.net>
+What: ACPI procfs interface
+When: July 2008
+Why: ACPI sysfs conversion should be finished by January 2008.
+ ACPI procfs interface will be removed in July 2008 so that
+ there is enough time for the user space to catch up.
+Who: Zhang Rui <rui.zhang@intel.com>
---------------------------
-What: ACPI hooks (X86_SPEEDSTEP_CENTRINO_ACPI) in speedstep-centrino driver
-When: December 2006
-Why: Speedstep-centrino driver with ACPI hooks and acpi-cpufreq driver are
- functionally very much similar. They talk to ACPI in same way. Only
- difference between them is the way they do frequency transitions.
- One uses MSRs and the other one uses IO ports. Functionaliy of
- speedstep_centrino with ACPI hooks is now merged into acpi-cpufreq.
- That means one common driver will support all Intel Enhanced Speedstep
- capable CPUs. That means less confusion over name of
- speedstep-centrino driver (with that driver supposed to be used on
- non-centrino platforms). That means less duplication of code and
- less maintenance effort and no possibility of these two drivers
- going out of sync.
- Current users of speedstep_centrino with ACPI hooks are requested to
- switch over to acpi-cpufreq driver. speedstep-centrino will continue
- to work using older non-ACPI static table based scheme even after this
- date.
-
-Who: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
+What: /proc/acpi/button
+When: August 2007
+Why: /proc/acpi/button has been replaced by events to the input layer
+ since 2.6.20.
+Who: Len Brown <len.brown@intel.com>
---------------------------
-<<<<<<< test:Documentation/feature-removal-schedule.txt
-What: ACPI hotkey driver (CONFIG_ACPI_HOTKEY)
-When: 2.6.21
-Why: hotkey.c was an attempt to consolidate multiple drivers that use
- ACPI to implement hotkeys. However, hotkeys are not documented
- in the ACPI specification, so the drivers used undocumented
- vendor-specific hooks and turned out to be more different than
- the same.
+What: /proc/acpi/event
+When: February 2008
+Why: /proc/acpi/event has been replaced by events via the input layer
+ and netlink since 2.6.23.
+Who: Len Brown <len.brown@intel.com>
- Further, the keys and the features supplied by each platform
- are different, so there will always be a need for
- platform-specific drivers.
+---------------------------
- So the new plan is to delete hotkey.c and instead, work on the
- platform specific drivers to try to make them look the same
- to the user when they supply the same features.
+What: i2c-ixp2000, i2c-ixp4xx and scx200_i2c drivers
+When: September 2007
+Why: Obsolete. The new i2c-gpio driver replaces all hardware-specific
+ I2C-over-GPIO drivers.
+Who: Jean Delvare <khali@linux-fr.org>
- hotkey.c has always depended on CONFIG_EXPERIMENTAL
+---------------------------
-Who: Len Brown <len.brown@intel.com>
+What: 'time' kernel boot parameter
+When: January 2008
+Why: replaced by 'printk.time=<value>' so that printk timestamps can be
+ enabled or disabled as needed
+Who: Randy Dunlap <randy.dunlap@oracle.com>
---------------------------
-What: /sys/firmware/acpi/namespace
-When: 2.6.21
-Why: The ACPI namespace is effectively the symbol list for
- the BIOS. The device names are completely arbitrary
- and have no place being exposed to user-space.
+What: drivers depending on OSS_OBSOLETE
+When: options in 2.6.23, code in 2.6.25
+Why: obsolete OSS drivers
+Who: Adrian Bunk <bunk@stusta.de>
- For those interested in the BIOS ACPI namespace,
- the BIOS can be extracted and disassembled with acpidump
- and iasl as documented in the pmtools package here:
- http://ftp.kernel.org/pub/linux/kernel/people/lenb/acpi/utils
-Who: Len Brown <len.brown@intel.com>
+---------------------------
+
+What: libata spindown skipping and warning
+When: Dec 2008
+Why: Some halt(8) implementations synchronize caches for and spin
+ down libata disks because libata didn't use to spin down disk on
+ system halt (only synchronized caches).
+ Spin down on system halt is now implemented. sysfs node
+ /sys/class/scsi_disk/h:c:i:l/manage_start_stop is present if
+ spin down support is available.
+ Because issuing spin down command to an already spun down disk
+ makes some disks spin up just to spin down again, libata tracks
+ device spindown status to skip the extra spindown command and
+ warn about it.
+ This is to give userspace tools the time to get updated and will
+ be removed after userspace is reasonably updated.
+Who: Tejun Heo <htejun@gmail.com>
---------------------------
-What: ACPI procfs interface
-When: July 2007
-Why: After ACPI sysfs conversion, ACPI attributes will be duplicated
- in sysfs and the ACPI procfs interface should be removed.
-Who: Zhang Rui <rui.zhang@intel.com>
+What: Legacy RTC drivers (under drivers/i2c/chips)
+When: November 2007
+Why: Obsolete. We have a RTC subsystem with better drivers.
+Who: Jean Delvare <khali@linux-fr.org>
---------------------------
-What: /proc/acpi/button
-When: August 2007
-Why: /proc/acpi/button has been replaced by events to the input layer
- since 2.6.20.
-Who: Len Brown <len.brown@intel.com>
+What: iptables SAME target
+When: 1.1. 2008
+Files: net/ipv4/netfilter/ipt_SAME.c, include/linux/netfilter_ipv4/ipt_SAME.h
+Why: Obsolete for multiple years now, NAT core provides the same behaviour.
+ Unfixable broken wrt. 32/64 bit cleanness.
+Who: Patrick McHardy <kaber@trash.net>
+
+---------------------------
+
+What: The arch/ppc and include/asm-ppc directories
+When: Jun 2008
+Why: The arch/powerpc tree is the merged architecture for ppc32 and ppc64
+ platforms. Currently there are efforts underway to port the remaining
+ arch/ppc platforms to the merged tree. New submissions to the arch/ppc
+ tree have been frozen with the 2.6.22 kernel release and that tree will
+ remain in bug-fix only mode until its scheduled removal. Platforms
+ that are not ported by June 2008 will be removed due to the lack of an
+ interested maintainer.
+Who: linuxppc-dev@ozlabs.org
+
+---------------------------
+
+What: mthca driver's MSI support
+When: January 2008
+Files: drivers/infiniband/hw/mthca/*.[ch]
+Why: All mthca hardware also supports MSI-X, which provides
+ strictly more functionality than MSI. So there is no point in
+ having both MSI-X and MSI support in the driver.
+Who: Roland Dreier <rolandd@cisco.com>
---------------------------
What: sk98lin network driver
-When: July 2007
+When: Feburary 2008
Why: In kernel tree version of driver is unmaintained. Sk98lin driver
replaced by the skge driver.
-Who: Stephen Hemminger <shemminger@osdl.org>
+Who: Stephen Hemminger <shemminger@linux-foundation.org>
+
+---------------------------
+
+What: i386/x86_64 bzImage symlinks
+When: April 2008
+
+Why: The i386/x86_64 merge provides a symlink to the old bzImage
+ location so not yet updated user space tools, e.g. package
+ scripts, do not break.
+Who: Thomas Gleixner <tglx@linutronix.de>
---------------------------
-What: Compaq touchscreen device emulation
-When: Oct 2007
-Files: drivers/input/tsdev.c
-Why: The code says it was obsolete when it was written in 2001.
- tslib is a userspace library which does anything tsdev can do and
- much more besides in userspace where this code belongs. There is no
- longer any need for tsdev and applications should have converted to
- use tslib by now.
- The name "tsdev" is also extremely confusing and lots of people have
- it loaded when they don't need/use it.
-Who: Richard Purdie <rpurdie@rpsys.net>
+What: shaper network driver
+When: January 2008
+Files: drivers/net/shaper.c, include/linux/if_shaper.h
+Why: This driver has been marked obsolete for many years.
+ It was only designed to work on lower speed links and has design
+ flaws that lead to machine crashes. The qdisc infrastructure in
+ 2.4 or later kernels, provides richer features and is more robust.
+Who: Stephen Hemminger <shemminger@linux-foundation.org>
---------------------------
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff