-/*
- * this routine handles the overflow of the microsecond field
- *
- * The tricky bits of code to handle the accurate clock support
- * were provided by Dave Mills (Mills@UDEL.EDU) of NTP fame.
- * They were originally developed for SUN and DEC kernels.
- * All the kudos should go to Dave for this stuff.
- *
- */
-static void second_overflow(void)
-{
- long ltemp;
-
- /* Bump the maxerror field */
- time_maxerror += time_tolerance >> SHIFT_USEC;
- if ( time_maxerror > NTP_PHASE_LIMIT ) {
- time_maxerror = NTP_PHASE_LIMIT;
- time_status |= STA_UNSYNC;
- }
-
- /*
- * Leap second processing. If in leap-insert state at
- * the end of the day, the system clock is set back one
- * second; if in leap-delete state, the system clock is
- * set ahead one second. The microtime() routine or
- * external clock driver will insure that reported time
- * is always monotonic. The ugly divides should be
- * replaced.
- */
- switch (time_state) {
-
- case TIME_OK:
- if (time_status & STA_INS)
- time_state = TIME_INS;
- else if (time_status & STA_DEL)
- time_state = TIME_DEL;
- break;
-
- case TIME_INS:
- if (xtime.tv_sec % 86400 == 0) {
- xtime.tv_sec--;
- wall_to_monotonic.tv_sec++;
- /* The timer interpolator will make time change gradually instead
- * of an immediate jump by one second.
- */
- time_interpolator_update(-NSEC_PER_SEC);
- time_state = TIME_OOP;
- clock_was_set();
- printk(KERN_NOTICE "Clock: inserting leap second 23:59:60 UTC\n");
- }
- break;
-
- case TIME_DEL:
- if ((xtime.tv_sec + 1) % 86400 == 0) {
- xtime.tv_sec++;
- wall_to_monotonic.tv_sec--;
- /* Use of time interpolator for a gradual change of time */
- time_interpolator_update(NSEC_PER_SEC);
- time_state = TIME_WAIT;
- clock_was_set();
- printk(KERN_NOTICE "Clock: deleting leap second 23:59:59 UTC\n");
- }
- break;
-
- case TIME_OOP:
- time_state = TIME_WAIT;
- break;
-
- case TIME_WAIT:
- if (!(time_status & (STA_INS | STA_DEL)))
- time_state = TIME_OK;
- }
-
- /*
- * Compute the phase adjustment for the next second. In
- * PLL mode, the offset is reduced by a fixed factor
- * times the time constant. In FLL mode the offset is
- * used directly. In either mode, the maximum phase
- * adjustment for each second is clamped so as to spread
- * the adjustment over not more than the number of
- * seconds between updates.
- */
- if (time_offset < 0) {
- ltemp = -time_offset;
- if (!(time_status & STA_FLL))
- ltemp >>= SHIFT_KG + time_constant;
- if (ltemp > (MAXPHASE / MINSEC) << SHIFT_UPDATE)
- ltemp = (MAXPHASE / MINSEC) << SHIFT_UPDATE;
- time_offset += ltemp;
- time_adj = -ltemp << (SHIFT_SCALE - SHIFT_HZ - SHIFT_UPDATE);
- } else {
- ltemp = time_offset;
- if (!(time_status & STA_FLL))
- ltemp >>= SHIFT_KG + time_constant;
- if (ltemp > (MAXPHASE / MINSEC) << SHIFT_UPDATE)
- ltemp = (MAXPHASE / MINSEC) << SHIFT_UPDATE;
- time_offset -= ltemp;
- time_adj = ltemp << (SHIFT_SCALE - SHIFT_HZ - SHIFT_UPDATE);
- }
-
- /*
- * Compute the frequency estimate and additional phase
- * adjustment due to frequency error for the next
- * second. When the PPS signal is engaged, gnaw on the
- * watchdog counter and update the frequency computed by
- * the pll and the PPS signal.
- */
- pps_valid++;
- if (pps_valid == PPS_VALID) { /* PPS signal lost */
- pps_jitter = MAXTIME;
- pps_stabil = MAXFREQ;
- time_status &= ~(STA_PPSSIGNAL | STA_PPSJITTER |
- STA_PPSWANDER | STA_PPSERROR);
- }
- ltemp = time_freq + pps_freq;
- if (ltemp < 0)
- time_adj -= -ltemp >>
- (SHIFT_USEC + SHIFT_HZ - SHIFT_SCALE);
- else
- time_adj += ltemp >>
- (SHIFT_USEC + SHIFT_HZ - SHIFT_SCALE);
-
-#if HZ == 100
- /* Compensate for (HZ==100) != (1 << SHIFT_HZ).
- * Add 25% and 3.125% to get 128.125; => only 0.125% error (p. 14)
- */
- if (time_adj < 0)
- time_adj -= (-time_adj >> 2) + (-time_adj >> 5);
- else
- time_adj += (time_adj >> 2) + (time_adj >> 5);
-#endif
-#if HZ == 1000
- /* Compensate for (HZ==1000) != (1 << SHIFT_HZ).
- * Add 1.5625% and 0.78125% to get 1023.4375; => only 0.05% error (p. 14)
- */
- if (time_adj < 0)
- time_adj -= (-time_adj >> 6) + (-time_adj >> 7);
- else
- time_adj += (time_adj >> 6) + (time_adj >> 7);
-#endif
-}
-
-/* in the NTP reference this is called "hardclock()" */
-static void update_wall_time_one_tick(void)
-{
- long time_adjust_step, delta_nsec;
-
- if ( (time_adjust_step = time_adjust) != 0 ) {
- /* We are doing an adjtime thing.
- *
- * Prepare time_adjust_step to be within bounds.
- * Note that a positive time_adjust means we want the clock
- * to run faster.
- *
- * Limit the amount of the step to be in the range
- * -tickadj .. +tickadj
- */
- if (time_adjust > tickadj)
- time_adjust_step = tickadj;
- else if (time_adjust < -tickadj)
- time_adjust_step = -tickadj;
-
- /* Reduce by this step the amount of time left */
- time_adjust -= time_adjust_step;
- }
- delta_nsec = tick_nsec + time_adjust_step * 1000;