+ * @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a
+ * FREQ attribute (for the initial frequency if no peer can be found)
+ * and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those
+ * should be fixed rather than automatically determined. Can only be
+ * executed on a network interface that is UP, and fixed BSSID/FREQ
+ * may be rejected. Another optional parameter is the beacon interval,
+ * given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not
+ * given defaults to 100 TU (102.4ms).
+ * @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is
+ * determined by the network interface.
+ *
+ * @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute
+ * to identify the device, and the TESTDATA blob attribute to pass through
+ * to the driver.
+ *
+ * @NL80211_CMD_CONNECT: connection request and notification; this command
+ * requests to connect to a specified network but without separating
+ * auth and assoc steps. For this, you need to specify the SSID in a
+ * %NL80211_ATTR_SSID attribute, and can optionally specify the association
+ * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
+ * %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_CONTROL_PORT.
+ * It is also sent as an event, with the BSSID and response IEs when the
+ * connection is established or failed to be established. This can be
+ * determined by the STATUS_CODE attribute.
+ * @NL80211_CMD_ROAM: request that the card roam (currently not implemented),
+ * sent as an event when the card/driver roamed by itself.
+ * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
+ * userspace that a connection was dropped by the AP or due to other
+ * reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
+ * %NL80211_ATTR_REASON_CODE attributes are used.
+ *
+ * @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices
+ * associated with this wiphy must be down and will follow.
+ *
+ * @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified
+ * channel for the specified amount of time. This can be used to do
+ * off-channel operations like transmit a Public Action frame and wait for
+ * a response while being associated to an AP on another channel.
+ * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify which
+ * radio is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
+ * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
+ * optionally used to specify additional channel parameters.
+ * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
+ * to remain on the channel. This command is also used as an event to
+ * notify when the requested duration starts (it may take a while for the
+ * driver to schedule this time due to other concurrent needs for the
+ * radio).
+ * When called, this operation returns a cookie (%NL80211_ATTR_COOKIE)
+ * that will be included with any events pertaining to this request;
+ * the cookie is also used to cancel the request.
+ * @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a
+ * pending remain-on-channel duration if the desired operation has been
+ * completed prior to expiration of the originally requested duration.
+ * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the
+ * radio. The %NL80211_ATTR_COOKIE attribute must be given as well to
+ * uniquely identify the request.
+ * This command is also used as an event to notify when a requested
+ * remain-on-channel duration has expired.
+ *
+ * @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX
+ * rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
+ * and @NL80211_ATTR_TX_RATES the set of allowed rates.
+ *
+ * @NL80211_CMD_REGISTER_ACTION: Register for receiving certain action frames
+ * (via @NL80211_CMD_ACTION) for processing in userspace. This command
+ * requires an interface index and a match attribute containing the first
+ * few bytes of the frame that should match, e.g. a single byte for only
+ * a category match or four bytes for vendor frames including the OUI.
+ * The registration cannot be dropped, but is removed automatically
+ * when the netlink socket is closed. Multiple registrations can be made.
+ * @NL80211_CMD_ACTION: Action frame TX request and RX notification. This
+ * command is used both as a request to transmit an Action frame and as an
+ * event indicating reception of an Action frame that was not processed in
+ * kernel code, but is for us (i.e., which may need to be processed in a
+ * user space application). %NL80211_ATTR_FRAME is used to specify the
+ * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
+ * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on
+ * which channel the frame is to be transmitted or was received. This
+ * channel has to be the current channel (remain-on-channel or the
+ * operational channel). When called, this operation returns a cookie
+ * (%NL80211_ATTR_COOKIE) that will be included with the TX status event
+ * pertaining to the TX request.
+ * @NL80211_CMD_ACTION_TX_STATUS: Report TX status of an Action frame
+ * transmitted with %NL80211_CMD_ACTION. %NL80211_ATTR_COOKIE identifies
+ * the TX command and %NL80211_ATTR_FRAME includes the contents of the
+ * frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
+ * the frame.
+ * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
+ * is used to configure connection quality monitoring notification trigger
+ * levels.
+ * @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
+ * command is used as an event to indicate the that a trigger level was
+ * reached.
+ * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
+ * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed
+ * by %NL80211_ATTR_IFINDEX) shall operate on.
+ * In case multiple channels are supported by the device, the mechanism
+ * with which it switches channels is implementation-defined.
+ * When a monitor interface is given, it can only switch channel while
+ * no other interfaces are operating to avoid disturbing the operation
+ * of any other interfaces, and other interfaces will again take
+ * precedence when they are used.
+ *