+config SERIAL_SB1250_DUART
+ tristate "BCM1xxx on-chip DUART serial support"
+ depends on SIBYTE_SB1xxx_SOC=y
+ select SERIAL_CORE
+ default y
+ ---help---
+ Support for the asynchronous serial interface (DUART) included in
+ the BCM1250 and derived System-On-a-Chip (SOC) devices. Note that
+ the letter D in DUART stands for "dual", which is how the device
+ is implemented. Depending on the SOC configuration there may be
+ one or more DUARTs available of which all are handled.
+
+ If unsure, say Y. To compile this driver as a module, choose M here:
+ the module will be called sb1250-duart.
+
+config SERIAL_SB1250_DUART_CONSOLE
+ bool "Support for console on a BCM1xxx DUART serial port"
+ depends on SERIAL_SB1250_DUART=y
+ select SERIAL_CORE_CONSOLE
+ default y
+ ---help---
+ If you say Y here, it will be possible to use a serial port as the
+ system console (the system console is the device which receives all
+ kernel messages and warnings and which allows logins in single user
+ mode).
+
+ If unsure, say Y.
+
+config SERIAL_ATMEL
+ bool "AT91 / AT32 on-chip serial port support"
+ depends on (ARM && ARCH_AT91) || AVR32
+ select SERIAL_CORE
+ help
+ This enables the driver for the on-chip UARTs of the Atmel
+ AT91 and AT32 processors.
+
+config SERIAL_ATMEL_CONSOLE
+ bool "Support for console on AT91 / AT32 serial port"
+ depends on SERIAL_ATMEL=y
+ select SERIAL_CORE_CONSOLE
+ help
+ Say Y here if you wish to use an on-chip UART on a Atmel
+ AT91 or AT32 processor as the system console (the system
+ console is the device which receives all kernel messages and
+ warnings and which allows logins in single user mode).
+
+config SERIAL_ATMEL_PDC
+ bool "Support DMA transfers on AT91 / AT32 serial port"
+ depends on SERIAL_ATMEL
+ default y
+ help
+ Say Y here if you wish to use the PDC to do DMA transfers to
+ and from the Atmel AT91 / AT32 serial port. In order to
+ actually use DMA transfers, make sure that the use_dma_tx
+ and use_dma_rx members in the atmel_uart_data struct is set
+ appropriately for each port.
+
+ Note that break and error handling currently doesn't work
+ properly when DMA is enabled. Make sure that ports where
+ this matters don't use DMA.
+
+config SERIAL_ATMEL_TTYAT
+ bool "Install as device ttyATn instead of ttySn"
+ depends on SERIAL_ATMEL=y
+ help
+ Say Y here if you wish to have the internal AT91 / AT32 UARTs
+ appear as /dev/ttyATn (major 204, minor starting at 154)
+ instead of the normal /dev/ttySn (major 4, minor starting at
+ 64). This is necessary if you also want other UARTs, such as
+ external 8250/16C550 compatible UARTs.
+ The ttySn nodes are legally reserved for the 8250 serial driver
+ but are often misused by other serial drivers.
+
+ To use this, you should create suitable ttyATn device nodes in
+ /dev/, and pass "console=ttyATn" to the kernel.
+
+ Say Y if you have an external 8250/16C550 UART. If unsure, say N.
+
+config SERIAL_KS8695
+ bool "Micrel KS8695 (Centaur) serial port support"
+ depends on ARCH_KS8695
+ select SERIAL_CORE
+ help
+ This selects the Micrel Centaur KS8695 UART. Say Y here.
+
+config SERIAL_KS8695_CONSOLE
+ bool "Support for console on KS8695 (Centaur) serial port"
+ depends on SERIAL_KS8695=y
+ select SERIAL_CORE_CONSOLE
+ help
+ Say Y here if you wish to use a KS8695 (Centaur) UART as the
+ system console (the system console is the device which
+ receives all kernel messages and warnings and which allows
+ logins in single user mode).
+
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff