-#define E2P_ALLOWED_CHANNEL E2P_REG(0x18)
-
-#define E2P_PHY_REG E2P_REG(0x1a)
-#define E2P_DEVICE_VER E2P_REG(0x20)
-#define E2P_36M_CAL_VALUE1 E2P_REG(0x28)
-#define E2P_36M_CAL_VALUE2 E2P_REG(0x2a)
-#define E2P_36M_CAL_VALUE3 E2P_REG(0x2c)
-#define E2P_36M_CAL_VALUE4 E2P_REG(0x2e)
-#define E2P_11A_INT_VALUE1 E2P_REG(0x30)
-#define E2P_11A_INT_VALUE2 E2P_REG(0x32)
-#define E2P_11A_INT_VALUE3 E2P_REG(0x34)
-#define E2P_11A_INT_VALUE4 E2P_REG(0x36)
-#define E2P_48M_CAL_VALUE1 E2P_REG(0x38)
-#define E2P_48M_CAL_VALUE2 E2P_REG(0x3a)
-#define E2P_48M_CAL_VALUE3 E2P_REG(0x3c)
-#define E2P_48M_CAL_VALUE4 E2P_REG(0x3e)
-#define E2P_48M_INT_VALUE1 E2P_REG(0x40)
-#define E2P_48M_INT_VALUE2 E2P_REG(0x42)
-#define E2P_48M_INT_VALUE3 E2P_REG(0x44)
-#define E2P_48M_INT_VALUE4 E2P_REG(0x46)
-#define E2P_54M_CAL_VALUE1 E2P_REG(0x48) /* ??? */
-#define E2P_54M_CAL_VALUE2 E2P_REG(0x4a)
-#define E2P_54M_CAL_VALUE3 E2P_REG(0x4c)
-#define E2P_54M_CAL_VALUE4 E2P_REG(0x4e)
-#define E2P_54M_INT_VALUE1 E2P_REG(0x50)
-#define E2P_54M_INT_VALUE2 E2P_REG(0x52)
-#define E2P_54M_INT_VALUE3 E2P_REG(0x54)
-#define E2P_54M_INT_VALUE4 E2P_REG(0x56)
-
-/* All 16 bit values */
-#define FW_FIRMWARE_VER FW_REG(0)
-/* non-zero if USB high speed connection */
-#define FW_USB_SPEED FW_REG(1)
-#define FW_FIX_TX_RATE FW_REG(2)
-/* Seems to be able to control LEDs over the firmware */
-#define FW_LINK_STATUS FW_REG(3)
-#define FW_SOFT_RESET FW_REG(4)
-#define FW_FLASH_CHK FW_REG(5)
+#define E2P_ALLOWED_CHANNEL E2P_DATA(0x18)
+
+#define E2P_DEVICE_VER E2P_DATA(0x20)
+#define E2P_PHY_REG E2P_DATA(0x25)
+#define E2P_36M_CAL_VALUE1 E2P_DATA(0x28)
+#define E2P_36M_CAL_VALUE2 E2P_DATA(0x2a)
+#define E2P_36M_CAL_VALUE3 E2P_DATA(0x2c)
+#define E2P_36M_CAL_VALUE4 E2P_DATA(0x2e)
+#define E2P_11A_INT_VALUE1 E2P_DATA(0x30)
+#define E2P_11A_INT_VALUE2 E2P_DATA(0x32)
+#define E2P_11A_INT_VALUE3 E2P_DATA(0x34)
+#define E2P_11A_INT_VALUE4 E2P_DATA(0x36)
+#define E2P_48M_CAL_VALUE1 E2P_DATA(0x38)
+#define E2P_48M_CAL_VALUE2 E2P_DATA(0x3a)
+#define E2P_48M_CAL_VALUE3 E2P_DATA(0x3c)
+#define E2P_48M_CAL_VALUE4 E2P_DATA(0x3e)
+#define E2P_48M_INT_VALUE1 E2P_DATA(0x40)
+#define E2P_48M_INT_VALUE2 E2P_DATA(0x42)
+#define E2P_48M_INT_VALUE3 E2P_DATA(0x44)
+#define E2P_48M_INT_VALUE4 E2P_DATA(0x46)
+#define E2P_54M_CAL_VALUE1 E2P_DATA(0x48) /* ??? */
+#define E2P_54M_CAL_VALUE2 E2P_DATA(0x4a)
+#define E2P_54M_CAL_VALUE3 E2P_DATA(0x4c)
+#define E2P_54M_CAL_VALUE4 E2P_DATA(0x4e)
+#define E2P_54M_INT_VALUE1 E2P_DATA(0x50)
+#define E2P_54M_INT_VALUE2 E2P_DATA(0x52)
+#define E2P_54M_INT_VALUE3 E2P_DATA(0x54)
+#define E2P_54M_INT_VALUE4 E2P_DATA(0x56)
+
+/* This word contains the base address of the FW_REG_ registers below */
+#define FWRAW_REGS_ADDR FWRAW_DATA(0x1d)
+
+/* All 16 bit values, offset from the address in FWRAW_REGS_ADDR */
+enum {
+ FW_REG_FIRMWARE_VER = 0,
+ /* non-zero if USB high speed connection */
+ FW_REG_USB_SPEED = 1,
+ FW_REG_FIX_TX_RATE = 2,
+ /* Seems to be able to control LEDs over the firmware */
+ FW_REG_LED_LINK_STATUS = 3,
+ FW_REG_SOFT_RESET = 4,
+ FW_REG_FLASH_CHK = 5,
+};