-static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
-{
- void __iomem *mem;
- struct ath_softc *sc;
- struct ieee80211_hw *hw;
- u8 csz;
- u32 val;
- int ret = 0;
- struct ath_hal *ah;
-
- if (pci_enable_device(pdev))
- return -EIO;
-
- ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
-
- if (ret) {
- printk(KERN_ERR "ath9k: 32-bit DMA not available\n");
- goto bad;
- }
-
- ret = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
-
- if (ret) {
- printk(KERN_ERR "ath9k: 32-bit DMA consistent "
- "DMA enable failed\n");
- goto bad;
- }
-
- /*
- * Cache line size is used to size and align various
- * structures used to communicate with the hardware.
- */
- pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz);
- if (csz == 0) {
- /*
- * Linux 2.4.18 (at least) writes the cache line size
- * register as a 16-bit wide register which is wrong.
- * We must have this setup properly for rx buffer
- * DMA to work so force a reasonable value here if it
- * comes up zero.
- */
- csz = L1_CACHE_BYTES / sizeof(u32);
- pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz);
- }
- /*
- * The default setting of latency timer yields poor results,
- * set it to the value used by other systems. It may be worth
- * tweaking this setting more.
- */
- pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8);
-
- pci_set_master(pdev);
-
- /*
- * Disable the RETRY_TIMEOUT register (0x41) to keep
- * PCI Tx retries from interfering with C3 CPU state.
- */
- pci_read_config_dword(pdev, 0x40, &val);
- if ((val & 0x0000ff00) != 0)
- pci_write_config_dword(pdev, 0x40, val & 0xffff00ff);
-
- ret = pci_request_region(pdev, 0, "ath9k");
- if (ret) {
- dev_err(&pdev->dev, "PCI memory region reserve error\n");
- ret = -ENODEV;
- goto bad;
- }
-
- mem = pci_iomap(pdev, 0, 0);
- if (!mem) {
- printk(KERN_ERR "PCI memory map error\n") ;
- ret = -EIO;
- goto bad1;
- }
-
- hw = ieee80211_alloc_hw(sizeof(struct ath_softc), &ath9k_ops);
- if (hw == NULL) {
- printk(KERN_ERR "ath_pci: no memory for ieee80211_hw\n");
- goto bad2;
- }
-
- SET_IEEE80211_DEV(hw, &pdev->dev);
- pci_set_drvdata(pdev, hw);
-
- sc = hw->priv;
- sc->hw = hw;
- sc->pdev = pdev;
- sc->mem = mem;
-
- if (ath_attach(id->device, sc) != 0) {
- ret = -ENODEV;
- goto bad3;
- }
-
- /* setup interrupt service routine */
-
- if (request_irq(pdev->irq, ath_isr, IRQF_SHARED, "ath", sc)) {
- printk(KERN_ERR "%s: request_irq failed\n",
- wiphy_name(hw->wiphy));
- ret = -EIO;
- goto bad4;
- }
-
- ah = sc->sc_ah;
- printk(KERN_INFO
- "%s: Atheros AR%s MAC/BB Rev:%x "
- "AR%s RF Rev:%x: mem=0x%lx, irq=%d\n",
- wiphy_name(hw->wiphy),
- ath_mac_bb_name(ah->ah_macVersion),
- ah->ah_macRev,
- ath_rf_name((ah->ah_analog5GhzRev & AR_RADIO_SREV_MAJOR)),
- ah->ah_phyRev,
- (unsigned long)mem, pdev->irq);
-
- return 0;
-bad4:
- ath_detach(sc);
-bad3:
- ieee80211_free_hw(hw);
-bad2:
- pci_iounmap(pdev, mem);
-bad1:
- pci_release_region(pdev, 0);
-bad:
- pci_disable_device(pdev);
- return ret;
-}
-
-static void ath_pci_remove(struct pci_dev *pdev)
-{
- struct ieee80211_hw *hw = pci_get_drvdata(pdev);
- struct ath_softc *sc = hw->priv;
-
- ath_detach(sc);
- if (pdev->irq)
- free_irq(pdev->irq, sc);
- pci_iounmap(pdev, sc->mem);
- pci_release_region(pdev, 0);
- pci_disable_device(pdev);
- ieee80211_free_hw(hw);
-}
-
-#ifdef CONFIG_PM
-
-static int ath_pci_suspend(struct pci_dev *pdev, pm_message_t state)
-{
- struct ieee80211_hw *hw = pci_get_drvdata(pdev);
- struct ath_softc *sc = hw->priv;
-
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
-
-#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
- if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
- cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll);
-#endif
-
- pci_save_state(pdev);
- pci_disable_device(pdev);
- pci_set_power_state(pdev, 3);
-
- return 0;
-}
-
-static int ath_pci_resume(struct pci_dev *pdev)
-{
- struct ieee80211_hw *hw = pci_get_drvdata(pdev);
- struct ath_softc *sc = hw->priv;
- u32 val;
- int err;
-
- err = pci_enable_device(pdev);
- if (err)
- return err;
- pci_restore_state(pdev);
- /*
- * Suspend/Resume resets the PCI configuration space, so we have to
- * re-disable the RETRY_TIMEOUT register (0x41) to keep
- * PCI Tx retries from interfering with C3 CPU state
- */
- pci_read_config_dword(pdev, 0x40, &val);
- if ((val & 0x0000ff00) != 0)
- pci_write_config_dword(pdev, 0x40, val & 0xffff00ff);
-
- /* Enable LED */
- ath9k_hw_cfg_output(sc->sc_ah, ATH_LED_PIN,
- AR_GPIO_OUTPUT_MUX_AS_OUTPUT);
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
-
-#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
- /*
- * check the h/w rfkill state on resume
- * and start the rfkill poll timer
- */
- if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
- queue_delayed_work(sc->hw->workqueue,
- &sc->rf_kill.rfkill_poll, 0);
-#endif
-
- return 0;
-}
-
-#endif /* CONFIG_PM */
-
-MODULE_DEVICE_TABLE(pci, ath_pci_id_table);
-
-static struct pci_driver ath_pci_driver = {
- .name = "ath9k",
- .id_table = ath_pci_id_table,
- .probe = ath_pci_probe,
- .remove = ath_pci_remove,
-#ifdef CONFIG_PM
- .suspend = ath_pci_suspend,
- .resume = ath_pci_resume,
-#endif /* CONFIG_PM */
-};
-
-static int __init init_ath_pci(void)