-}
-
-static void __inline__ fec_phy_ack_intr(void)
-{
-}
-
-/* ------------------------------------------------------------------------- */
-
-#elif defined(CONFIG_M520x)
-
-/*
- * Code specific to Coldfire 520x
- */
-static void __inline__ fec_request_intrs(struct net_device *dev)
-{
- struct fec_enet_private *fep;
- int b;
- static const struct idesc {
- char *name;
- unsigned short irq;
- } *idp, id[] = {
- { "fec(TXF)", 23 },
- { "fec(RXF)", 27 },
- { "fec(MII)", 29 },
- { NULL },
- };
-
- fep = netdev_priv(dev);
- b = 64 + 13;
-
- /* Setup interrupt handlers. */
- for (idp = id; idp->name; idp++) {
- if (request_irq(b+idp->irq, fec_enet_interrupt, IRQF_DISABLED, idp->name,dev) != 0)
- printk("FEC: Could not allocate %s IRQ(%d)!\n", idp->name, b+idp->irq);
- }
-
- /* Unmask interrupts at ColdFire interrupt controller */
- {
- volatile unsigned char *icrp;
- volatile unsigned long *imrp;
-
- icrp = (volatile unsigned char *) (MCF_IPSBAR + MCFICM_INTC0 +
- MCFINTC_ICR0);
- for (b = 36; (b < 49); b++)
- icrp[b] = 0x04;
- imrp = (volatile unsigned long *) (MCF_IPSBAR + MCFICM_INTC0 +
- MCFINTC_IMRH);
- *imrp &= ~0x0001FFF0;
- }
- *(volatile unsigned char *)(MCF_IPSBAR + MCF_GPIO_PAR_FEC) |= 0xf0;
- *(volatile unsigned char *)(MCF_IPSBAR + MCF_GPIO_PAR_FECI2C) |= 0x0f;
-}
-
-static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
-{
- volatile fec_t *fecp;
-
- fecp = fep->hwp;
- fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x04;
- fecp->fec_x_cntrl = 0x00;
-
- /*
- * Set MII speed to 2.5 MHz
- * See 5282 manual section 17.5.4.7: MSCR
- */
- fep->phy_speed = ((((MCF_CLK / 2) / (2500000 / 10)) + 5) / 10) * 2;
- fecp->fec_mii_speed = fep->phy_speed;
-
- fec_restart(dev, 0);
-}
-
-static void __inline__ fec_get_mac(struct net_device *dev)
-{
- struct fec_enet_private *fep = netdev_priv(dev);
- volatile fec_t *fecp;
- unsigned char *iap, tmpaddr[ETH_ALEN];
-
- fecp = fep->hwp;
-
- if (FEC_FLASHMAC) {
- /*
- * Get MAC address from FLASH.
- * If it is all 1's or 0's, use the default.
- */
- iap = FEC_FLASHMAC;
- if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
- (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
- iap = fec_mac_default;
- if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
- (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
- iap = fec_mac_default;
- } else {
- *((unsigned long *) &tmpaddr[0]) = fecp->fec_addr_low;
- *((unsigned short *) &tmpaddr[4]) = (fecp->fec_addr_high >> 16);
- iap = &tmpaddr[0];
- }
-
- memcpy(dev->dev_addr, iap, ETH_ALEN);
-
- /* Adjust MAC if using default MAC address */
- if (iap == fec_mac_default)
- dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
-}
-
-static void __inline__ fec_disable_phy_intr(void)
-{
-}
-
-static void __inline__ fec_phy_ack_intr(void)
-{
-}
-
-/* ------------------------------------------------------------------------- */
-
-#elif defined(CONFIG_M532x)
-/*
- * Code specific for M532x
- */
-static void __inline__ fec_request_intrs(struct net_device *dev)
-{
- struct fec_enet_private *fep;
- int b;
- static const struct idesc {
- char *name;
- unsigned short irq;
- } *idp, id[] = {
- { "fec(TXF)", 36 },
- { "fec(RXF)", 40 },
- { "fec(MII)", 42 },
- { NULL },
- };
-
- fep = netdev_priv(dev);
- b = (fep->index) ? 128 : 64;
-
- /* Setup interrupt handlers. */
- for (idp = id; idp->name; idp++) {
- if (request_irq(b+idp->irq, fec_enet_interrupt, IRQF_DISABLED, idp->name,dev) != 0)
- printk("FEC: Could not allocate %s IRQ(%d)!\n",
- idp->name, b+idp->irq);
- }
-
- /* Unmask interrupts */
- MCF_INTC0_ICR36 = 0x2;
- MCF_INTC0_ICR37 = 0x2;
- MCF_INTC0_ICR38 = 0x2;
- MCF_INTC0_ICR39 = 0x2;
- MCF_INTC0_ICR40 = 0x2;
- MCF_INTC0_ICR41 = 0x2;
- MCF_INTC0_ICR42 = 0x2;
- MCF_INTC0_ICR43 = 0x2;
- MCF_INTC0_ICR44 = 0x2;
- MCF_INTC0_ICR45 = 0x2;
- MCF_INTC0_ICR46 = 0x2;
- MCF_INTC0_ICR47 = 0x2;
- MCF_INTC0_ICR48 = 0x2;
-
- MCF_INTC0_IMRH &= ~(
- MCF_INTC_IMRH_INT_MASK36 |
- MCF_INTC_IMRH_INT_MASK37 |
- MCF_INTC_IMRH_INT_MASK38 |
- MCF_INTC_IMRH_INT_MASK39 |
- MCF_INTC_IMRH_INT_MASK40 |
- MCF_INTC_IMRH_INT_MASK41 |
- MCF_INTC_IMRH_INT_MASK42 |
- MCF_INTC_IMRH_INT_MASK43 |
- MCF_INTC_IMRH_INT_MASK44 |
- MCF_INTC_IMRH_INT_MASK45 |
- MCF_INTC_IMRH_INT_MASK46 |
- MCF_INTC_IMRH_INT_MASK47 |
- MCF_INTC_IMRH_INT_MASK48 );
-
- /* Set up gpio outputs for MII lines */
- MCF_GPIO_PAR_FECI2C |= (0 |
- MCF_GPIO_PAR_FECI2C_PAR_MDC_EMDC |
- MCF_GPIO_PAR_FECI2C_PAR_MDIO_EMDIO);
- MCF_GPIO_PAR_FEC = (0 |
- MCF_GPIO_PAR_FEC_PAR_FEC_7W_FEC |
- MCF_GPIO_PAR_FEC_PAR_FEC_MII_FEC);
-}
-
-static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
-{
- volatile fec_t *fecp;
-
- fecp = fep->hwp;
- fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x04;
- fecp->fec_x_cntrl = 0x00;
-
- /*
- * Set MII speed to 2.5 MHz
- */
- fep->phy_speed = ((((MCF_CLK / 2) / (2500000 / 10)) + 5) / 10) * 2;
- fecp->fec_mii_speed = fep->phy_speed;
-
- fec_restart(dev, 0);
-}
-
-static void __inline__ fec_get_mac(struct net_device *dev)
-{
- struct fec_enet_private *fep = netdev_priv(dev);
- volatile fec_t *fecp;
- unsigned char *iap, tmpaddr[ETH_ALEN];
-
- fecp = fep->hwp;
-
- if (FEC_FLASHMAC) {
- /*
- * Get MAC address from FLASH.
- * If it is all 1's or 0's, use the default.
- */
- iap = FEC_FLASHMAC;
- if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
- (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
- iap = fec_mac_default;
- if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
- (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
- iap = fec_mac_default;
- } else {
- *((unsigned long *) &tmpaddr[0]) = fecp->fec_addr_low;
- *((unsigned short *) &tmpaddr[4]) = (fecp->fec_addr_high >> 16);
- iap = &tmpaddr[0];
- }
-
- memcpy(dev->dev_addr, iap, ETH_ALEN);
-
- /* Adjust MAC if using default MAC address */
- if (iap == fec_mac_default)
- dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
-}
-
-static void __inline__ fec_disable_phy_intr(void)
-{
-}
-
-static void __inline__ fec_phy_ack_intr(void)
-{
-}
-
-#endif
-
-/* ------------------------------------------------------------------------- */
-
-static void mii_display_status(struct net_device *dev)
-{
- struct fec_enet_private *fep = netdev_priv(dev);
- volatile uint *s = &(fep->phy_status);
-
- if (!fep->link && !fep->old_link) {
- /* Link is still down - don't print anything */
- return;
- }
-
- printk("%s: status: ", dev->name);
-
- if (!fep->link) {
- printk("link down");
- } else {
- printk("link up");
-
- switch(*s & PHY_STAT_SPMASK) {
- case PHY_STAT_100FDX: printk(", 100MBit Full Duplex"); break;
- case PHY_STAT_100HDX: printk(", 100MBit Half Duplex"); break;
- case PHY_STAT_10FDX: printk(", 10MBit Full Duplex"); break;
- case PHY_STAT_10HDX: printk(", 10MBit Half Duplex"); break;
- default:
- printk(", Unknown speed/duplex");
- }
-
- if (*s & PHY_STAT_ANC)
- printk(", auto-negotiation complete");
- }
-
- if (*s & PHY_STAT_FAULT)
- printk(", remote fault");
-
- printk(".\n");
-}
-
-static void mii_display_config(struct work_struct *work)
-{
- struct fec_enet_private *fep = container_of(work, struct fec_enet_private, phy_task);
- struct net_device *dev = fep->netdev;
- uint status = fep->phy_status;
-
- /*
- ** When we get here, phy_task is already removed from
- ** the workqueue. It is thus safe to allow to reuse it.
- */
- fep->mii_phy_task_queued = 0;
- printk("%s: config: auto-negotiation ", dev->name);
-
- if (status & PHY_CONF_ANE)
- printk("on");
- else
- printk("off");
-
- if (status & PHY_CONF_100FDX)
- printk(", 100FDX");
- if (status & PHY_CONF_100HDX)
- printk(", 100HDX");
- if (status & PHY_CONF_10FDX)
- printk(", 10FDX");
- if (status & PHY_CONF_10HDX)
- printk(", 10HDX");
- if (!(status & PHY_CONF_SPMASK))
- printk(", No speed/duplex selected?");
-
- if (status & PHY_CONF_LOOP)
- printk(", loopback enabled");
-
- printk(".\n");
-
- fep->sequence_done = 1;
-}
-
-static void mii_relink(struct work_struct *work)
-{
- struct fec_enet_private *fep = container_of(work, struct fec_enet_private, phy_task);
- struct net_device *dev = fep->netdev;
- int duplex;
-
- /*
- ** When we get here, phy_task is already removed from
- ** the workqueue. It is thus safe to allow to reuse it.
- */
- fep->mii_phy_task_queued = 0;
- fep->link = (fep->phy_status & PHY_STAT_LINK) ? 1 : 0;
- mii_display_status(dev);
- fep->old_link = fep->link;
-
- if (fep->link) {
- duplex = 0;
- if (fep->phy_status
- & (PHY_STAT_100FDX | PHY_STAT_10FDX))
- duplex = 1;
- fec_restart(dev, duplex);
- } else
- fec_stop(dev);
-
-#if 0
- enable_irq(fep->mii_irq);
-#endif
-
-}
-
-/* mii_queue_relink is called in interrupt context from mii_link_interrupt */
-static void mii_queue_relink(uint mii_reg, struct net_device *dev)
-{
- struct fec_enet_private *fep = netdev_priv(dev);
-
- /*
- ** We cannot queue phy_task twice in the workqueue. It
- ** would cause an endless loop in the workqueue.
- ** Fortunately, if the last mii_relink entry has not yet been
- ** executed now, it will do the job for the current interrupt,
- ** which is just what we want.
- */
- if (fep->mii_phy_task_queued)
- return;
-
- fep->mii_phy_task_queued = 1;
- INIT_WORK(&fep->phy_task, mii_relink);
- schedule_work(&fep->phy_task);
-}
-
-/* mii_queue_config is called in interrupt context from fec_enet_mii */
-static void mii_queue_config(uint mii_reg, struct net_device *dev)
-{
- struct fec_enet_private *fep = netdev_priv(dev);