+config AD525X_DPOT
+ tristate "Analog Devices Digital Potentiometers"
+ depends on (I2C || SPI) && SYSFS
+ help
+ If you say yes here, you get support for the Analog Devices
+ AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255
+ AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203,
+ AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235,
+ AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293,
+ AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242,
+ AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282,
+ ADN2860
+ digital potentiometer chips.
+
+ See Documentation/misc-devices/ad525x_dpot.txt for the
+ userspace interface.
+
+ This driver can also be built as a module. If so, the module
+ will be called ad525x_dpot.
+
+config AD525X_DPOT_I2C
+ tristate "support I2C bus connection"
+ depends on AD525X_DPOT && I2C
+ help
+ Say Y here if you have a digital potentiometers hooked to an I2C bus.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ad525x_dpot-i2c.
+
+config AD525X_DPOT_SPI
+ tristate "support SPI bus connection"
+ depends on AD525X_DPOT && SPI_MASTER
+ help
+ Say Y here if you have a digital potentiometers hooked to an SPI bus.
+
+ If unsure, say N (but it's safe to say "Y").
+
+ To compile this driver as a module, choose M here: the
+ module will be called ad525x_dpot-spi.
+
+config ATMEL_PWM
+ tristate "Atmel AT32/AT91 PWM support"
+ depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9
+ help
+ This option enables device driver support for the PWM channels
+ on certain Atmel processors. Pulse Width Modulation is used for
+ purposes including software controlled power-efficient backlights
+ on LCD displays, motor control, and waveform generation.
+
+config ATMEL_TCLIB
+ bool "Atmel AT32/AT91 Timer/Counter Library"
+ depends on (AVR32 || ARCH_AT91)
+ help
+ Select this if you want a library to allocate the Timer/Counter
+ blocks found on many Atmel processors. This facilitates using
+ these blocks by different drivers despite processor differences.
+
+config ATMEL_TCB_CLKSRC
+ bool "TC Block Clocksource"
+ depends on ATMEL_TCLIB && GENERIC_TIME
+ default y
+ help
+ Select this to get a high precision clocksource based on a
+ TC block with a 5+ MHz base clock rate. Two timer channels
+ are combined to make a single 32-bit timer.
+
+ When GENERIC_CLOCKEVENTS is defined, the third timer channel
+ may be used as a clock event device supporting oneshot mode
+ (delays of up to two seconds) based on the 32 KiHz clock.
+
+config ATMEL_TCB_CLKSRC_BLOCK
+ int
+ depends on ATMEL_TCB_CLKSRC
+ prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+ default 0
+ range 0 1
+ help
+ Some chips provide more than one TC block, so you have the
+ choice of which one to use for the clock framework. The other
+ TC can be used for other purposes, such as PWM generation and
+ interval timing.
+