+ return map;
+}
+
+static bool piix_no_sidpr(struct ata_host *host)
+{
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+
+ /*
+ * Samsung DB-P70 only has three ATA ports exposed and
+ * curiously the unconnected first port reports link online
+ * while not responding to SRST protocol causing excessive
+ * detection delay.
+ *
+ * Unfortunately, the system doesn't carry enough DMI
+ * information to identify the machine but does have subsystem
+ * vendor and device set. As it's unclear whether the
+ * subsystem vendor/device is used only for this specific
+ * board, the port can't be disabled solely with the
+ * information; however, turning off SIDPR access works around
+ * the problem. Turn it off.
+ *
+ * This problem is reported in bnc#441240.
+ *
+ * https://bugzilla.novell.com/show_bug.cgi?id=441420
+ */
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == 0x2920 &&
+ pdev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG &&
+ pdev->subsystem_device == 0xb049) {
+ dev_printk(KERN_WARNING, host->dev,
+ "Samsung DB-P70 detected, disabling SIDPR\n");
+ return true;
+ }
+
+ return false;
+}
+
+static int __devinit piix_init_sidpr(struct ata_host *host)
+{
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+ struct piix_host_priv *hpriv = host->private_data;
+ struct ata_link *link0 = &host->ports[0]->link;
+ u32 scontrol;
+ int i, rc;
+
+ /* check for availability */
+ for (i = 0; i < 4; i++)
+ if (hpriv->map[i] == IDE)
+ return 0;
+
+ /* is it blacklisted? */
+ if (piix_no_sidpr(host))
+ return 0;
+
+ if (!(host->ports[0]->flags & PIIX_FLAG_SIDPR))
+ return 0;
+
+ if (pci_resource_start(pdev, PIIX_SIDPR_BAR) == 0 ||
+ pci_resource_len(pdev, PIIX_SIDPR_BAR) != PIIX_SIDPR_LEN)
+ return 0;
+
+ if (pcim_iomap_regions(pdev, 1 << PIIX_SIDPR_BAR, DRV_NAME))
+ return 0;
+
+ hpriv->sidpr = pcim_iomap_table(pdev)[PIIX_SIDPR_BAR];
+
+ /* SCR access via SIDPR doesn't work on some configurations.
+ * Give it a test drive by inhibiting power save modes which
+ * we'll do anyway.
+ */
+ piix_sidpr_scr_read(link0, SCR_CONTROL, &scontrol);
+
+ /* if IPM is already 3, SCR access is probably working. Don't
+ * un-inhibit power save modes as BIOS might have inhibited
+ * them for a reason.
+ */
+ if ((scontrol & 0xf00) != 0x300) {
+ scontrol |= 0x300;
+ piix_sidpr_scr_write(link0, SCR_CONTROL, scontrol);
+ piix_sidpr_scr_read(link0, SCR_CONTROL, &scontrol);
+
+ if ((scontrol & 0xf00) != 0x300) {
+ dev_printk(KERN_INFO, host->dev, "SCR access via "
+ "SIDPR is available but doesn't work\n");
+ return 0;
+ }
+ }
+
+ /* okay, SCRs available, set ops and ask libata for slave_link */
+ for (i = 0; i < 2; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ ap->ops = &piix_sidpr_sata_ops;
+
+ if (ap->flags & ATA_FLAG_SLAVE_POSS) {
+ rc = ata_slave_link_init(ap);
+ if (rc)
+ return rc;
+ }
+ }
+
+ return 0;