+choice
+ prompt "Early debugging console"
+ depends on PPC_EARLY_DEBUG
+ help
+ Use the selected console for early debugging. Careful, if you
+ enable debugging for the wrong type of machine your kernel
+ _will not boot_.
+
+config PPC_EARLY_DEBUG_LPAR
+ bool "LPAR HV Console"
+ depends on PPC_PSERIES
+ help
+ Select this to enable early debugging for a machine with a HVC
+ console on vterm 0.
+
+config PPC_EARLY_DEBUG_G5
+ bool "Apple G5"
+ depends on PPC_PMAC64
+ help
+ Select this to enable early debugging for Apple G5 machines.
+
+config PPC_EARLY_DEBUG_RTAS_PANEL
+ bool "RTAS Panel"
+ depends on PPC_RTAS
+ help
+ Select this to enable early debugging via the RTAS panel.
+
+config PPC_EARLY_DEBUG_RTAS_CONSOLE
+ bool "RTAS Console"
+ depends on PPC_RTAS
+ select UDBG_RTAS_CONSOLE
+ help
+ Select this to enable early debugging via the RTAS console.
+
+config PPC_EARLY_DEBUG_MAPLE
+ bool "Maple real mode"
+ depends on PPC_MAPLE
+ help
+ Select this to enable early debugging for Maple.
+
+config PPC_EARLY_DEBUG_ISERIES
+ bool "iSeries HV Console"
+ depends on PPC_ISERIES
+ help
+ Select this to enable early debugging for legacy iSeries. You need
+ to hit "Ctrl-x Ctrl-x" to see the messages on the console.
+
+config PPC_EARLY_DEBUG_PAS_REALMODE
+ bool "PA Semi real mode"
+ depends on PPC_PASEMI
+ help
+ Select this to enable early debugging for PA Semi.
+ Output will be on UART0.
+
+config PPC_EARLY_DEBUG_BEAT
+ bool "Beat HV Console"
+ depends on PPC_CELLEB
+ select PPC_UDBG_BEAT
+ help
+ Select this to enable early debugging for Celleb with Beat.
+
+config PPC_EARLY_DEBUG_44x
+ bool "Early serial debugging for IBM/AMCC 44x CPUs"
+ depends on 44x
+ help
+ Select this to enable early debugging for IBM 44x chips via the
+ inbuilt serial port. If you enable this, ensure you set
+ PPC_EARLY_DEBUG_44x_PHYSLOW below to suit your target board.
+
+config PPC_EARLY_DEBUG_40x
+ bool "Early serial debugging for IBM/AMCC 40x CPUs"
+ depends on 40x
+ help
+ Select this to enable early debugging for IBM 40x chips via the
+ inbuilt serial port. This works on chips with a 16550 compatible
+ UART. Xilinx chips with uartlite cannot use this option.
+
+config PPC_EARLY_DEBUG_CPM
+ bool "Early serial debugging for Freescale CPM-based serial ports"
+ depends on SERIAL_CPM
+ select PIN_TLB if PPC_8xx
+ help
+ Select this to enable early debugging for Freescale chips
+ using a CPM-based serial port. This assumes that the bootwrapper
+ has run, and set up the CPM in a particular way.
+
+config PPC_EARLY_DEBUG_USBGECKO
+ bool "Early debugging through the USB Gecko adapter"
+ depends on GAMECUBE_COMMON
+ select USBGECKO_UDBG
+ help
+ Select this to enable early debugging for Nintendo GameCube/Wii
+ consoles via an external USB Gecko adapter.
+
+endchoice
+
+config PPC_EARLY_DEBUG_44x_PHYSLOW
+ hex "Low 32 bits of early debug UART physical address"
+ depends on PPC_EARLY_DEBUG_44x
+ default "0x40000200"
+ help
+ You probably want 0x40000200 for ebony boards and
+ 0x40000300 for taishan
+
+config PPC_EARLY_DEBUG_44x_PHYSHIGH
+ hex "EPRN of early debug UART physical address"
+ depends on PPC_EARLY_DEBUG_44x
+ default "0x1"
+
+config PPC_EARLY_DEBUG_40x_PHYSADDR
+ hex "Early debug UART physical address"
+ depends on PPC_EARLY_DEBUG_40x
+ default "0xef600300"
+
+config PPC_EARLY_DEBUG_CPM_ADDR
+ hex "CPM UART early debug transmit descriptor address"
+ depends on PPC_EARLY_DEBUG_CPM
+ default "0xfa202008" if PPC_EP88XC
+ default "0xf0001ff8" if CPM2
+ default "0xff002008" if CPM1
+ help
+ This specifies the address of the transmit descriptor
+ used for early debug output. Because it is needed before
+ platform probing is done, all platforms selected must
+ share the same address.