+
+GPIO implementor's framework (OPTIONAL)
+=======================================
+As noted earlier, there is an optional implementation framework making it
+easier for platforms to support different kinds of GPIO controller using
+the same programming interface. This framework is called "gpiolib".
+
+As a debugging aid, if debugfs is available a /sys/kernel/debug/gpio file
+will be found there. That will list all the controllers registered through
+this framework, and the state of the GPIOs currently in use.
+
+
+Controller Drivers: gpio_chip
+-----------------------------
+In this framework each GPIO controller is packaged as a "struct gpio_chip"
+with information common to each controller of that type:
+
+ - methods to establish GPIO direction
+ - methods used to access GPIO values
+ - flag saying whether calls to its methods may sleep
+ - optional debugfs dump method (showing extra state like pullup config)
+ - label for diagnostics
+
+There is also per-instance data, which may come from device.platform_data:
+the number of its first GPIO, and how many GPIOs it exposes.
+
+The code implementing a gpio_chip should support multiple instances of the
+controller, possibly using the driver model. That code will configure each
+gpio_chip and issue gpiochip_add(). Removing a GPIO controller should be
+rare; use gpiochip_remove() when it is unavoidable.
+
+Most often a gpio_chip is part of an instance-specific structure with state
+not exposed by the GPIO interfaces, such as addressing, power management,
+and more. Chips such as codecs will have complex non-GPIO state.
+
+Any debugfs dump method should normally ignore signals which haven't been
+requested as GPIOs. They can use gpiochip_is_requested(), which returns
+either NULL or the label associated with that GPIO when it was requested.
+
+
+Platform Support
+----------------
+To support this framework, a platform's Kconfig will "select" either
+ARCH_REQUIRE_GPIOLIB or ARCH_WANT_OPTIONAL_GPIOLIB
+and arrange that its <asm/gpio.h> includes <asm-generic/gpio.h> and defines
+three functions: gpio_get_value(), gpio_set_value(), and gpio_cansleep().
+They may also want to provide a custom value for ARCH_NR_GPIOS.
+
+ARCH_REQUIRE_GPIOLIB means that the gpio-lib code will always get compiled
+into the kernel on that architecture.
+
+ARCH_WANT_OPTIONAL_GPIOLIB means the gpio-lib code defaults to off and the user
+can enable it and build it into the kernel optionally.
+
+If neither of these options are selected, the platform does not support
+GPIOs through GPIO-lib and the code cannot be enabled by the user.
+
+Trivial implementations of those functions can directly use framework
+code, which always dispatches through the gpio_chip:
+
+ #define gpio_get_value __gpio_get_value
+ #define gpio_set_value __gpio_set_value
+ #define gpio_cansleep __gpio_cansleep
+
+Fancier implementations could instead define those as inline functions with
+logic optimizing access to specific SOC-based GPIOs. For example, if the
+referenced GPIO is the constant "12", getting or setting its value could
+cost as little as two or three instructions, never sleeping. When such an
+optimization is not possible those calls must delegate to the framework
+code, costing at least a few dozen instructions. For bitbanged I/O, such
+instruction savings can be significant.
+
+For SOCs, platform-specific code defines and registers gpio_chip instances
+for each bank of on-chip GPIOs. Those GPIOs should be numbered/labeled to
+match chip vendor documentation, and directly match board schematics. They
+may well start at zero and go up to a platform-specific limit. Such GPIOs
+are normally integrated into platform initialization to make them always be
+available, from arch_initcall() or earlier; they can often serve as IRQs.
+
+
+Board Support
+-------------
+For external GPIO controllers -- such as I2C or SPI expanders, ASICs, multi
+function devices, FPGAs or CPLDs -- most often board-specific code handles
+registering controller devices and ensures that their drivers know what GPIO
+numbers to use with gpiochip_add(). Their numbers often start right after
+platform-specific GPIOs.
+
+For example, board setup code could create structures identifying the range
+of GPIOs that chip will expose, and passes them to each GPIO expander chip
+using platform_data. Then the chip driver's probe() routine could pass that
+data to gpiochip_add().
+
+Initialization order can be important. For example, when a device relies on
+an I2C-based GPIO, its probe() routine should only be called after that GPIO
+becomes available. That may mean the device should not be registered until
+calls for that GPIO can work. One way to address such dependencies is for
+such gpio_chip controllers to provide setup() and teardown() callbacks to
+board specific code; those board specific callbacks would register devices
+once all the necessary resources are available, and remove them later when
+the GPIO controller device becomes unavailable.
+
+
+Sysfs Interface for Userspace (OPTIONAL)
+========================================
+Platforms which use the "gpiolib" implementors framework may choose to
+configure a sysfs user interface to GPIOs. This is different from the
+debugfs interface, since it provides control over GPIO direction and
+value instead of just showing a gpio state summary. Plus, it could be
+present on production systems without debugging support.
+
+Given appropriate hardware documentation for the system, userspace could
+know for example that GPIO #23 controls the write protect line used to
+protect boot loader segments in flash memory. System upgrade procedures
+may need to temporarily remove that protection, first importing a GPIO,
+then changing its output state, then updating the code before re-enabling
+the write protection. In normal use, GPIO #23 would never be touched,
+and the kernel would have no need to know about it.
+
+Again depending on appropriate hardware documentation, on some systems
+userspace GPIO can be used to determine system configuration data that
+standard kernels won't know about. And for some tasks, simple userspace
+GPIO drivers could be all that the system really needs.
+
+Note that standard kernel drivers exist for common "LEDs and Buttons"
+GPIO tasks: "leds-gpio" and "gpio_keys", respectively. Use those
+instead of talking directly to the GPIOs; they integrate with kernel
+frameworks better than your userspace code could.
+
+
+Paths in Sysfs
+--------------
+There are three kinds of entry in /sys/class/gpio:
+
+ - Control interfaces used to get userspace control over GPIOs;
+
+ - GPIOs themselves; and
+
+ - GPIO controllers ("gpio_chip" instances).
+
+That's in addition to standard files including the "device" symlink.
+
+The control interfaces are write-only:
+
+ /sys/class/gpio/
+
+ "export" ... Userspace may ask the kernel to export control of
+ a GPIO to userspace by writing its number to this file.
+
+ Example: "echo 19 > export" will create a "gpio19" node
+ for GPIO #19, if that's not requested by kernel code.
+
+ "unexport" ... Reverses the effect of exporting to userspace.
+
+ Example: "echo 19 > unexport" will remove a "gpio19"
+ node exported using the "export" file.
+
+GPIO signals have paths like /sys/class/gpio/gpio42/ (for GPIO #42)
+and have the following read/write attributes:
+
+ /sys/class/gpio/gpioN/
+
+ "direction" ... reads as either "in" or "out". This value may
+ normally be written. Writing as "out" defaults to
+ initializing the value as low. To ensure glitch free
+ operation, values "low" and "high" may be written to
+ configure the GPIO as an output with that initial value.
+
+ Note that this attribute *will not exist* if the kernel
+ doesn't support changing the direction of a GPIO, or
+ it was exported by kernel code that didn't explicitly
+ allow userspace to reconfigure this GPIO's direction.
+
+ "value" ... reads as either 0 (low) or 1 (high). If the GPIO
+ is configured as an output, this value may be written;
+ any nonzero value is treated as high.
+
+ "edge" ... reads as either "none", "rising", "falling", or
+ "both". Write these strings to select the signal edge(s)
+ that will make poll(2) on the "value" file return.
+
+ This file exists only if the pin can be configured as an
+ interrupt generating input pin.
+
+ "active_low" ... reads as either 0 (false) or 1 (true). Write
+ any nonzero value to invert the value attribute both
+ for reading and writing. Existing and subsequent
+ poll(2) support configuration via the edge attribute
+ for "rising" and "falling" edges will follow this
+ setting.
+
+GPIO controllers have paths like /sys/class/gpio/gpiochip42/ (for the
+controller implementing GPIOs starting at #42) and have the following
+read-only attributes:
+
+ /sys/class/gpio/gpiochipN/
+
+ "base" ... same as N, the first GPIO managed by this chip
+
+ "label" ... provided for diagnostics (not always unique)
+
+ "ngpio" ... how many GPIOs this manges (N to N + ngpio - 1)
+
+Board documentation should in most cases cover what GPIOs are used for
+what purposes. However, those numbers are not always stable; GPIOs on
+a daughtercard might be different depending on the base board being used,
+or other cards in the stack. In such cases, you may need to use the
+gpiochip nodes (possibly in conjunction with schematics) to determine
+the correct GPIO number to use for a given signal.
+
+
+Exporting from Kernel code
+--------------------------
+Kernel code can explicitly manage exports of GPIOs which have already been
+requested using gpio_request():
+
+ /* export the GPIO to userspace */
+ int gpio_export(unsigned gpio, bool direction_may_change);
+
+ /* reverse gpio_export() */
+ void gpio_unexport();
+
+ /* create a sysfs link to an exported GPIO node */
+ int gpio_export_link(struct device *dev, const char *name,
+ unsigned gpio)
+
+ /* change the polarity of a GPIO node in sysfs */
+ int gpio_sysfs_set_active_low(unsigned gpio, int value);
+
+After a kernel driver requests a GPIO, it may only be made available in
+the sysfs interface by gpio_export(). The driver can control whether the
+signal direction may change. This helps drivers prevent userspace code
+from accidentally clobbering important system state.
+
+This explicit exporting can help with debugging (by making some kinds
+of experiments easier), or can provide an always-there interface that's
+suitable for documenting as part of a board support package.
+
+After the GPIO has been exported, gpio_export_link() allows creating
+symlinks from elsewhere in sysfs to the GPIO sysfs node. Drivers can
+use this to provide the interface under their own device in sysfs with
+a descriptive name.
+
+Drivers can use gpio_sysfs_set_active_low() to hide GPIO line polarity
+differences between boards from user space. This only affects the
+sysfs interface. Polarity change can be done both before and after
+gpio_export(), and previously enabled poll(2) support for either
+rising or falling edge will be reconfigured to follow this setting.