power management: remove firmware disk mode

[safe/jmp/linux-2.6] / include / linux / pm.h

/*
 *  pm.h - Power management interface
 *
 *  Copyright (C) 2000 Andrew Henroid
 *
 *  This program is free software; you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License as published by
 *  the Free Software Foundation; either version 2 of the License, or
 *  (at your option) any later version.
 *
 *  This program is distributed in the hope that it will be useful,
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *  GNU General Public License for more details.
 *
 *  You should have received a copy of the GNU General Public License
 *  along with this program; if not, write to the Free Software
 *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */

#ifndef _LINUX_PM_H
#define _LINUX_PM_H

#ifdef __KERNEL__

#include <linux/list.h>
#include <asm/atomic.h>

/*
 * Power management requests... these are passed to pm_send_all() and friends.
 *
 * these functions are old and deprecated, see below.
 */
typedef int __bitwise pm_request_t;

#define PM_SUSPEND      ((__force pm_request_t) 1)      /* enter D1-D3 */
#define PM_RESUME       ((__force pm_request_t) 2)      /* enter D0 */


/*
 * Device types... these are passed to pm_register
 */
typedef int __bitwise pm_dev_t;

#define PM_UNKNOWN_DEV  ((__force pm_dev_t) 0)  /* generic */
#define PM_SYS_DEV      ((__force pm_dev_t) 1)  /* system device (fan, KB controller, ...) */
#define PM_PCI_DEV      ((__force pm_dev_t) 2)  /* PCI device */
#define PM_USB_DEV      ((__force pm_dev_t) 3)  /* USB device */
#define PM_SCSI_DEV     ((__force pm_dev_t) 4)  /* SCSI device */
#define PM_ISA_DEV      ((__force pm_dev_t) 5)  /* ISA device */
#define PM_MTD_DEV      ((__force pm_dev_t) 6)  /* Memory Technology Device */

/*
 * System device hardware ID (PnP) values
 */
enum
{
        PM_SYS_UNKNOWN = 0x00000000, /* generic */
        PM_SYS_KBC =     0x41d00303, /* keyboard controller */
        PM_SYS_COM =     0x41d00500, /* serial port */
        PM_SYS_IRDA =    0x41d00510, /* IRDA controller */
        PM_SYS_FDC =     0x41d00700, /* floppy controller */
        PM_SYS_VGA =     0x41d00900, /* VGA controller */
        PM_SYS_PCMCIA =  0x41d00e00, /* PCMCIA controller */
};

/*
 * Device identifier
 */
#define PM_PCI_ID(dev) ((dev)->bus->number << 16 | (dev)->devfn)

/*
 * Request handler callback
 */
struct pm_dev;

typedef int (*pm_callback)(struct pm_dev *dev, pm_request_t rqst, void *data);

/*
 * Dynamic device information
 */
struct pm_dev
{
        pm_dev_t         type;
        unsigned long    id;
        pm_callback      callback;
        void            *data;

        unsigned long    flags;
        unsigned long    state;
        unsigned long    prev_state;

        struct list_head entry;
};

/* Functions above this comment are list-based old-style power
 * managment. Please avoid using them.  */

/*
 * Callbacks for platform drivers to implement.
 */
extern void (*pm_idle)(void);
extern void (*pm_power_off)(void);

typedef int __bitwise suspend_state_t;

#define PM_SUSPEND_ON           ((__force suspend_state_t) 0)
#define PM_SUSPEND_STANDBY      ((__force suspend_state_t) 1)
#define PM_SUSPEND_MEM          ((__force suspend_state_t) 3)
#define PM_SUSPEND_DISK         ((__force suspend_state_t) 4)
#define PM_SUSPEND_MAX          ((__force suspend_state_t) 5)

typedef int __bitwise suspend_disk_method_t;

/* invalid must be 0 so struct pm_ops initialisers can leave it out */
#define PM_DISK_INVALID         ((__force suspend_disk_method_t) 0)
#define PM_DISK_PLATFORM        ((__force suspend_disk_method_t) 1)
#define PM_DISK_SHUTDOWN        ((__force suspend_disk_method_t) 2)
#define PM_DISK_REBOOT          ((__force suspend_disk_method_t) 3)
#define PM_DISK_TEST            ((__force suspend_disk_method_t) 4)
#define PM_DISK_TESTPROC        ((__force suspend_disk_method_t) 5)
#define PM_DISK_MAX             ((__force suspend_disk_method_t) 6)

/**
 * struct pm_ops - Callbacks for managing platform dependent suspend states.
 * @valid: Callback to determine whether the given state can be entered.
 *      If %CONFIG_SOFTWARE_SUSPEND is set then %PM_SUSPEND_DISK is
 *      always valid and never passed to this call.
 *      If not assigned, all suspend states are advertised as valid
 *      in /sys/power/state (but can still be rejected by prepare or enter.)
 *
 * @prepare: Prepare the platform for the given suspend state. Can return a
 *      negative error code if necessary.
 *
 * @enter: Enter the given suspend state, must be assigned. Can return a
 *      negative error code if necessary.
 *
 * @finish: Called when the system has left the given state and all devices
 *      are resumed. The return value is ignored.
 *
 * @pm_disk_mode: The generic code always allows one of the shutdown methods
 *      %PM_DISK_SHUTDOWN, %PM_DISK_REBOOT, %PM_DISK_TEST and
 *      %PM_DISK_TESTPROC. If this variable is set, the mode it is set
 *      to is allowed in addition to those modes and is also made default.
 *      When this mode is sent selected, the @prepare call will be called
 *      before suspending to disk (if present), the @enter call should be
 *      present and will be called after all state has been saved and the
 *      machine is ready to be powered off; the @finish callback is called
 *      after state has been restored. All these calls are called with
 *      %PM_SUSPEND_DISK as the state.
 */
struct pm_ops {
        int (*valid)(suspend_state_t state);
        int (*prepare)(suspend_state_t state);
        int (*enter)(suspend_state_t state);
        int (*finish)(suspend_state_t state);
        suspend_disk_method_t pm_disk_mode;
};

/**
 * pm_set_ops - set platform dependent power management ops
 * @pm_ops: The new power management operations to set.
 */
extern void pm_set_ops(struct pm_ops *pm_ops);
extern struct pm_ops *pm_ops;
extern int pm_suspend(suspend_state_t state);


/**
 * arch_suspend_disable_irqs - disable IRQs for suspend
 *
 * Disables IRQs (in the default case). This is a weak symbol in the common
 * code and thus allows architectures to override it if more needs to be
 * done. Not called for suspend to disk.
 */
extern void arch_suspend_disable_irqs(void);

/**
 * arch_suspend_enable_irqs - enable IRQs after suspend
 *
 * Enables IRQs (in the default case). This is a weak symbol in the common
 * code and thus allows architectures to override it if more needs to be
 * done. Not called for suspend to disk.
 */
extern void arch_suspend_enable_irqs(void);

/*
 * Device power management
 */

struct device;

typedef struct pm_message {
        int event;
} pm_message_t;

/*
 * Several driver power state transitions are externally visible, affecting
 * the state of pending I/O queues and (for drivers that touch hardware)
 * interrupts, wakeups, DMA, and other hardware state.  There may also be
 * internal transitions to various low power modes, which are transparent
 * to the rest of the driver stack (such as a driver that's ON gating off
 * clocks which are not in active use).
 *
 * One transition is triggered by resume(), after a suspend() call; the
 * message is implicit:
 *
 * ON           Driver starts working again, responding to hardware events
 *              and software requests.  The hardware may have gone through
 *              a power-off reset, or it may have maintained state from the
 *              previous suspend() which the driver will rely on while
 *              resuming.  On most platforms, there are no restrictions on
 *              availability of resources like clocks during resume().
 *
 * Other transitions are triggered by messages sent using suspend().  All
 * these transitions quiesce the driver, so that I/O queues are inactive.
 * That commonly entails turning off IRQs and DMA; there may be rules
 * about how to quiesce that are specific to the bus or the device's type.
 * (For example, network drivers mark the link state.)  Other details may
 * differ according to the message:
 *
 * SUSPEND      Quiesce, enter a low power device state appropriate for
 *              the upcoming system state (such as PCI_D3hot), and enable
 *              wakeup events as appropriate.
 *
 * FREEZE       Quiesce operations so that a consistent image can be saved;
 *              but do NOT otherwise enter a low power device state, and do
 *              NOT emit system wakeup events.
 *
 * PRETHAW      Quiesce as if for FREEZE; additionally, prepare for restoring
 *              the system from a snapshot taken after an earlier FREEZE.
 *              Some drivers will need to reset their hardware state instead
 *              of preserving it, to ensure that it's never mistaken for the
 *              state which that earlier snapshot had set up.
 *
 * A minimally power-aware driver treats all messages as SUSPEND, fully
 * reinitializes its device during resume() -- whether or not it was reset
 * during the suspend/resume cycle -- and can't issue wakeup events.
 *
 * More power-aware drivers may also use low power states at runtime as
 * well as during system sleep states like PM_SUSPEND_STANDBY.  They may
 * be able to use wakeup events to exit from runtime low-power states,
 * or from system low-power states such as standby or suspend-to-RAM.
 */

#define PM_EVENT_ON 0
#define PM_EVENT_FREEZE 1
#define PM_EVENT_SUSPEND 2
#define PM_EVENT_PRETHAW 3

#define PMSG_FREEZE     ((struct pm_message){ .event = PM_EVENT_FREEZE, })
#define PMSG_PRETHAW    ((struct pm_message){ .event = PM_EVENT_PRETHAW, })
#define PMSG_SUSPEND    ((struct pm_message){ .event = PM_EVENT_SUSPEND, })
#define PMSG_ON         ((struct pm_message){ .event = PM_EVENT_ON, })

struct dev_pm_info {
        pm_message_t            power_state;
        unsigned                can_wakeup:1;
#ifdef  CONFIG_PM
        unsigned                should_wakeup:1;
        pm_message_t            prev_state;
        void                    * saved_state;
        struct device           * pm_parent;
        struct list_head        entry;
#endif
};

extern void device_pm_set_parent(struct device * dev, struct device * parent);

extern int device_power_down(pm_message_t state);
extern void device_power_up(void);
extern void device_resume(void);

#ifdef CONFIG_PM
extern suspend_disk_method_t pm_disk_mode;

extern int device_suspend(pm_message_t state);
extern int device_prepare_suspend(pm_message_t state);

#define device_set_wakeup_enable(dev,val) \
        ((dev)->power.should_wakeup = !!(val))
#define device_may_wakeup(dev) \
        (device_can_wakeup(dev) && (dev)->power.should_wakeup)

extern int dpm_runtime_suspend(struct device *, pm_message_t);
extern void dpm_runtime_resume(struct device *);
extern void __suspend_report_result(const char *function, void *fn, int ret);

#define suspend_report_result(fn, ret)                                  \
        do {                                                            \
                __suspend_report_result(__FUNCTION__, fn, ret);         \
        } while (0)

/*
 * Platform hook to activate device wakeup capability, if that's not already
 * handled by enable_irq_wake() etc.
 * Returns zero on success, else negative errno
 */
extern int (*platform_enable_wakeup)(struct device *dev, int is_on);

static inline int call_platform_enable_wakeup(struct device *dev, int is_on)
{
        if (platform_enable_wakeup)
                return (*platform_enable_wakeup)(dev, is_on);
        return 0;
}

#else /* !CONFIG_PM */

static inline int device_suspend(pm_message_t state)
{
        return 0;
}

#define device_set_wakeup_enable(dev,val)       do{}while(0)
#define device_may_wakeup(dev)                  (0)

static inline int dpm_runtime_suspend(struct device * dev, pm_message_t state)
{
        return 0;
}

static inline void dpm_runtime_resume(struct device * dev)
{
}

#define suspend_report_result(fn, ret) do { } while (0)

static inline int call_platform_enable_wakeup(struct device *dev, int is_on)
{
        return -EIO;
}

#endif

/* changes to device_may_wakeup take effect on the next pm state change.
 * by default, devices should wakeup if they can.
 */
#define device_can_wakeup(dev) \
        ((dev)->power.can_wakeup)
#define device_init_wakeup(dev,val) \
        do { \
                device_can_wakeup(dev) = !!(val); \
                device_set_wakeup_enable(dev,val); \
        } while(0)

#endif /* __KERNEL__ */

#endif /* _LINUX_PM_H */