ide: use lock bitops for ports serialization (v2)
[safe/jmp/linux-2.6] / include / linux / ide.h
1 #ifndef _IDE_H
2 #define _IDE_H
3 /*
4  *  linux/include/linux/ide.h
5  *
6  *  Copyright (C) 1994-2002  Linus Torvalds & authors
7  */
8
9 #include <linux/init.h>
10 #include <linux/ioport.h>
11 #include <linux/ata.h>
12 #include <linux/blkdev.h>
13 #include <linux/proc_fs.h>
14 #include <linux/interrupt.h>
15 #include <linux/bitops.h>
16 #include <linux/bio.h>
17 #include <linux/device.h>
18 #include <linux/pci.h>
19 #include <linux/completion.h>
20 #include <linux/pm.h>
21 #ifdef CONFIG_BLK_DEV_IDEACPI
22 #include <acpi/acpi.h>
23 #endif
24 #include <asm/byteorder.h>
25 #include <asm/system.h>
26 #include <asm/io.h>
27 #include <asm/mutex.h>
28
29 #if defined(CONFIG_CRIS) || defined(CONFIG_FRV)
30 # define SUPPORT_VLB_SYNC 0
31 #else
32 # define SUPPORT_VLB_SYNC 1
33 #endif
34
35 typedef unsigned char   byte;   /* used everywhere */
36
37 /*
38  * Probably not wise to fiddle with these
39  */
40 #define ERROR_MAX       8       /* Max read/write errors per sector */
41 #define ERROR_RESET     3       /* Reset controller every 4th retry */
42 #define ERROR_RECAL     1       /* Recalibrate every 2nd retry */
43
44 #define HWIF(drive)             ((ide_hwif_t *)((drive)->hwif))
45 #define HWGROUP(drive)          ((ide_hwgroup_t *)(HWIF(drive)->hwgroup))
46
47 /*
48  * Definitions for accessing IDE controller registers
49  */
50 #define IDE_NR_PORTS            (10)
51
52 struct ide_io_ports {
53         unsigned long   data_addr;
54
55         union {
56                 unsigned long error_addr;       /*   read:  error */
57                 unsigned long feature_addr;     /*  write: feature */
58         };
59
60         unsigned long   nsect_addr;
61         unsigned long   lbal_addr;
62         unsigned long   lbam_addr;
63         unsigned long   lbah_addr;
64
65         unsigned long   device_addr;
66
67         union {
68                 unsigned long status_addr;      /*  read: status  */
69                 unsigned long command_addr;     /* write: command */
70         };
71
72         unsigned long   ctl_addr;
73
74         unsigned long   irq_addr;
75 };
76
77 #define OK_STAT(stat,good,bad)  (((stat)&((good)|(bad)))==(good))
78
79 #define BAD_R_STAT      (ATA_BUSY | ATA_ERR)
80 #define BAD_W_STAT      (BAD_R_STAT | ATA_DF)
81 #define BAD_STAT        (BAD_R_STAT | ATA_DRQ)
82 #define DRIVE_READY     (ATA_DRDY | ATA_DSC)
83
84 #define BAD_CRC         (ATA_ABORTED | ATA_ICRC)
85
86 #define SATA_NR_PORTS           (3)     /* 16 possible ?? */
87
88 #define SATA_STATUS_OFFSET      (0)
89 #define SATA_ERROR_OFFSET       (1)
90 #define SATA_CONTROL_OFFSET     (2)
91
92 /*
93  * Our Physical Region Descriptor (PRD) table should be large enough
94  * to handle the biggest I/O request we are likely to see.  Since requests
95  * can have no more than 256 sectors, and since the typical blocksize is
96  * two or more sectors, we could get by with a limit of 128 entries here for
97  * the usual worst case.  Most requests seem to include some contiguous blocks,
98  * further reducing the number of table entries required.
99  *
100  * The driver reverts to PIO mode for individual requests that exceed
101  * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
102  * 100% of all crazy scenarios here is not necessary.
103  *
104  * As it turns out though, we must allocate a full 4KB page for this,
105  * so the two PRD tables (ide0 & ide1) will each get half of that,
106  * allowing each to have about 256 entries (8 bytes each) from this.
107  */
108 #define PRD_BYTES       8
109 #define PRD_ENTRIES     256
110
111 /*
112  * Some more useful definitions
113  */
114 #define PARTN_BITS      6       /* number of minor dev bits for partitions */
115 #define MAX_DRIVES      2       /* per interface; 2 assumed by lots of code */
116 #define SECTOR_SIZE     512
117
118 /*
119  * Timeouts for various operations:
120  */
121 enum {
122         /* spec allows up to 20ms */
123         WAIT_DRQ        = HZ / 10,      /* 100ms */
124         /* some laptops are very slow */
125         WAIT_READY      = 5 * HZ,       /* 5s */
126         /* should be less than 3ms (?), if all ATAPI CD is closed at boot */
127         WAIT_PIDENTIFY  = 10 * HZ,      /* 10s */
128         /* worst case when spinning up */
129         WAIT_WORSTCASE  = 30 * HZ,      /* 30s */
130         /* maximum wait for an IRQ to happen */
131         WAIT_CMD        = 10 * HZ,      /* 10s */
132         /* Some drives require a longer IRQ timeout. */
133         WAIT_FLOPPY_CMD = 50 * HZ,      /* 50s */
134         /*
135          * Some drives (for example, Seagate STT3401A Travan) require a very
136          * long timeout, because they don't return an interrupt or clear their
137          * BSY bit until after the command completes (even retension commands).
138          */
139         WAIT_TAPE_CMD   = 900 * HZ,     /* 900s */
140         /* minimum sleep time */
141         WAIT_MIN_SLEEP  = HZ / 50,      /* 20ms */
142 };
143
144 /*
145  * Op codes for special requests to be handled by ide_special_rq().
146  * Values should be in the range of 0x20 to 0x3f.
147  */
148 #define REQ_DRIVE_RESET         0x20
149 #define REQ_DEVSET_EXEC         0x21
150 #define REQ_PARK_HEADS          0x22
151 #define REQ_UNPARK_HEADS        0x23
152
153 /*
154  * Check for an interrupt and acknowledge the interrupt status
155  */
156 struct hwif_s;
157 typedef int (ide_ack_intr_t)(struct hwif_s *);
158
159 /*
160  * hwif_chipset_t is used to keep track of the specific hardware
161  * chipset used by each IDE interface, if known.
162  */
163 enum {          ide_unknown,    ide_generic,    ide_pci,
164                 ide_cmd640,     ide_dtc2278,    ide_ali14xx,
165                 ide_qd65xx,     ide_umc8672,    ide_ht6560b,
166                 ide_4drives,    ide_pmac,       ide_acorn,
167                 ide_au1xxx,     ide_palm3710
168 };
169
170 typedef u8 hwif_chipset_t;
171
172 /*
173  * Structure to hold all information about the location of this port
174  */
175 typedef struct hw_regs_s {
176         union {
177                 struct ide_io_ports     io_ports;
178                 unsigned long           io_ports_array[IDE_NR_PORTS];
179         };
180
181         int             irq;                    /* our irq number */
182         ide_ack_intr_t  *ack_intr;              /* acknowledge interrupt */
183         hwif_chipset_t  chipset;
184         struct device   *dev, *parent;
185         unsigned long   config;
186 } hw_regs_t;
187
188 void ide_init_port_data(struct hwif_s *, unsigned int);
189 void ide_init_port_hw(struct hwif_s *, hw_regs_t *);
190
191 static inline void ide_std_init_ports(hw_regs_t *hw,
192                                       unsigned long io_addr,
193                                       unsigned long ctl_addr)
194 {
195         unsigned int i;
196
197         for (i = 0; i <= 7; i++)
198                 hw->io_ports_array[i] = io_addr++;
199
200         hw->io_ports.ctl_addr = ctl_addr;
201 }
202
203 /* for IDE PCI controllers in legacy mode, temporary */
204 static inline int __ide_default_irq(unsigned long base)
205 {
206         switch (base) {
207 #ifdef CONFIG_IA64
208         case 0x1f0: return isa_irq_to_vector(14);
209         case 0x170: return isa_irq_to_vector(15);
210 #else
211         case 0x1f0: return 14;
212         case 0x170: return 15;
213 #endif
214         }
215         return 0;
216 }
217
218 #if defined(CONFIG_ARM) || defined(CONFIG_FRV) || defined(CONFIG_M68K) || \
219     defined(CONFIG_MIPS) || defined(CONFIG_MN10300) || defined(CONFIG_PARISC) \
220     || defined(CONFIG_PPC) || defined(CONFIG_SPARC) || defined(CONFIG_SPARC64)
221 #include <asm/ide.h>
222 #else
223 #include <asm-generic/ide_iops.h>
224 #endif
225
226 #define MAX_HWIFS       10
227
228 /* Currently only m68k, apus and m8xx need it */
229 #ifndef IDE_ARCH_ACK_INTR
230 # define ide_ack_intr(hwif) (1)
231 #endif
232
233 /* Currently only Atari needs it */
234 #ifndef IDE_ARCH_LOCK
235 # define ide_release_lock()                     do {} while (0)
236 # define ide_get_lock(hdlr, data)               do {} while (0)
237 #endif /* IDE_ARCH_LOCK */
238
239 /*
240  * Now for the data we need to maintain per-drive:  ide_drive_t
241  */
242
243 #define ide_scsi        0x21
244 #define ide_disk        0x20
245 #define ide_optical     0x7
246 #define ide_cdrom       0x5
247 #define ide_tape        0x1
248 #define ide_floppy      0x0
249
250 /*
251  * Special Driver Flags
252  *
253  * set_geometry : respecify drive geometry
254  * recalibrate  : seek to cyl 0
255  * set_multmode : set multmode count
256  * reserved     : unused
257  */
258 typedef union {
259         unsigned all                    : 8;
260         struct {
261                 unsigned set_geometry   : 1;
262                 unsigned recalibrate    : 1;
263                 unsigned set_multmode   : 1;
264                 unsigned reserved       : 5;
265         } b;
266 } special_t;
267
268 /*
269  * Status returned from various ide_ functions
270  */
271 typedef enum {
272         ide_stopped,    /* no drive operation was started */
273         ide_started,    /* a drive operation was started, handler was set */
274 } ide_startstop_t;
275
276 enum {
277         IDE_TFLAG_LBA48                 = (1 << 0),
278         IDE_TFLAG_FLAGGED               = (1 << 2),
279         IDE_TFLAG_OUT_DATA              = (1 << 3),
280         IDE_TFLAG_OUT_HOB_FEATURE       = (1 << 4),
281         IDE_TFLAG_OUT_HOB_NSECT         = (1 << 5),
282         IDE_TFLAG_OUT_HOB_LBAL          = (1 << 6),
283         IDE_TFLAG_OUT_HOB_LBAM          = (1 << 7),
284         IDE_TFLAG_OUT_HOB_LBAH          = (1 << 8),
285         IDE_TFLAG_OUT_HOB               = IDE_TFLAG_OUT_HOB_FEATURE |
286                                           IDE_TFLAG_OUT_HOB_NSECT |
287                                           IDE_TFLAG_OUT_HOB_LBAL |
288                                           IDE_TFLAG_OUT_HOB_LBAM |
289                                           IDE_TFLAG_OUT_HOB_LBAH,
290         IDE_TFLAG_OUT_FEATURE           = (1 << 9),
291         IDE_TFLAG_OUT_NSECT             = (1 << 10),
292         IDE_TFLAG_OUT_LBAL              = (1 << 11),
293         IDE_TFLAG_OUT_LBAM              = (1 << 12),
294         IDE_TFLAG_OUT_LBAH              = (1 << 13),
295         IDE_TFLAG_OUT_TF                = IDE_TFLAG_OUT_FEATURE |
296                                           IDE_TFLAG_OUT_NSECT |
297                                           IDE_TFLAG_OUT_LBAL |
298                                           IDE_TFLAG_OUT_LBAM |
299                                           IDE_TFLAG_OUT_LBAH,
300         IDE_TFLAG_OUT_DEVICE            = (1 << 14),
301         IDE_TFLAG_WRITE                 = (1 << 15),
302         IDE_TFLAG_FLAGGED_SET_IN_FLAGS  = (1 << 16),
303         IDE_TFLAG_IN_DATA               = (1 << 17),
304         IDE_TFLAG_CUSTOM_HANDLER        = (1 << 18),
305         IDE_TFLAG_DMA_PIO_FALLBACK      = (1 << 19),
306         IDE_TFLAG_IN_HOB_FEATURE        = (1 << 20),
307         IDE_TFLAG_IN_HOB_NSECT          = (1 << 21),
308         IDE_TFLAG_IN_HOB_LBAL           = (1 << 22),
309         IDE_TFLAG_IN_HOB_LBAM           = (1 << 23),
310         IDE_TFLAG_IN_HOB_LBAH           = (1 << 24),
311         IDE_TFLAG_IN_HOB_LBA            = IDE_TFLAG_IN_HOB_LBAL |
312                                           IDE_TFLAG_IN_HOB_LBAM |
313                                           IDE_TFLAG_IN_HOB_LBAH,
314         IDE_TFLAG_IN_HOB                = IDE_TFLAG_IN_HOB_FEATURE |
315                                           IDE_TFLAG_IN_HOB_NSECT |
316                                           IDE_TFLAG_IN_HOB_LBA,
317         IDE_TFLAG_IN_FEATURE            = (1 << 1),
318         IDE_TFLAG_IN_NSECT              = (1 << 25),
319         IDE_TFLAG_IN_LBAL               = (1 << 26),
320         IDE_TFLAG_IN_LBAM               = (1 << 27),
321         IDE_TFLAG_IN_LBAH               = (1 << 28),
322         IDE_TFLAG_IN_LBA                = IDE_TFLAG_IN_LBAL |
323                                           IDE_TFLAG_IN_LBAM |
324                                           IDE_TFLAG_IN_LBAH,
325         IDE_TFLAG_IN_TF                 = IDE_TFLAG_IN_NSECT |
326                                           IDE_TFLAG_IN_LBA,
327         IDE_TFLAG_IN_DEVICE             = (1 << 29),
328         IDE_TFLAG_HOB                   = IDE_TFLAG_OUT_HOB |
329                                           IDE_TFLAG_IN_HOB,
330         IDE_TFLAG_TF                    = IDE_TFLAG_OUT_TF |
331                                           IDE_TFLAG_IN_TF,
332         IDE_TFLAG_DEVICE                = IDE_TFLAG_OUT_DEVICE |
333                                           IDE_TFLAG_IN_DEVICE,
334         /* force 16-bit I/O operations */
335         IDE_TFLAG_IO_16BIT              = (1 << 30),
336         /* ide_task_t was allocated using kmalloc() */
337         IDE_TFLAG_DYN                   = (1 << 31),
338 };
339
340 struct ide_taskfile {
341         u8      hob_data;       /*  0: high data byte (for TASKFILE IOCTL) */
342
343         u8      hob_feature;    /*  1-5: additional data to support LBA48 */
344         u8      hob_nsect;
345         u8      hob_lbal;
346         u8      hob_lbam;
347         u8      hob_lbah;
348
349         u8      data;           /*  6: low data byte (for TASKFILE IOCTL) */
350
351         union {                 /*  7: */
352                 u8 error;       /*   read:  error */
353                 u8 feature;     /*  write: feature */
354         };
355
356         u8      nsect;          /*  8: number of sectors */
357         u8      lbal;           /*  9: LBA low */
358         u8      lbam;           /* 10: LBA mid */
359         u8      lbah;           /* 11: LBA high */
360
361         u8      device;         /* 12: device select */
362
363         union {                 /* 13: */
364                 u8 status;      /*  read: status  */
365                 u8 command;     /* write: command */
366         };
367 };
368
369 typedef struct ide_task_s {
370         union {
371                 struct ide_taskfile     tf;
372                 u8                      tf_array[14];
373         };
374         u32                     tf_flags;
375         int                     data_phase;
376         struct request          *rq;            /* copy of request */
377         void                    *special;       /* valid_t generally */
378 } ide_task_t;
379
380 /* ATAPI packet command flags */
381 enum {
382         /* set when an error is considered normal - no retry (ide-tape) */
383         PC_FLAG_ABORT                   = (1 << 0),
384         PC_FLAG_SUPPRESS_ERROR          = (1 << 1),
385         PC_FLAG_WAIT_FOR_DSC            = (1 << 2),
386         PC_FLAG_DMA_OK                  = (1 << 3),
387         PC_FLAG_DMA_IN_PROGRESS         = (1 << 4),
388         PC_FLAG_DMA_ERROR               = (1 << 5),
389         PC_FLAG_WRITING                 = (1 << 6),
390         /* command timed out */
391         PC_FLAG_TIMEDOUT                = (1 << 7),
392 };
393
394 /*
395  * With each packet command, we allocate a buffer of IDE_PC_BUFFER_SIZE bytes.
396  * This is used for several packet commands (not for READ/WRITE commands).
397  */
398 #define IDE_PC_BUFFER_SIZE      256
399 #define ATAPI_WAIT_PC           (60 * HZ)
400
401 struct ide_atapi_pc {
402         /* actual packet bytes */
403         u8 c[12];
404         /* incremented on each retry */
405         int retries;
406         int error;
407
408         /* bytes to transfer */
409         int req_xfer;
410         /* bytes actually transferred */
411         int xferred;
412
413         /* data buffer */
414         u8 *buf;
415         /* current buffer position */
416         u8 *cur_pos;
417         int buf_size;
418         /* missing/available data on the current buffer */
419         int b_count;
420
421         /* the corresponding request */
422         struct request *rq;
423
424         unsigned long flags;
425
426         /*
427          * those are more or less driver-specific and some of them are subject
428          * to change/removal later.
429          */
430         u8 pc_buf[IDE_PC_BUFFER_SIZE];
431
432         /* idetape only */
433         struct idetape_bh *bh;
434         char *b_data;
435
436         /* idescsi only for now */
437         struct scatterlist *sg;
438         unsigned int sg_cnt;
439
440         struct scsi_cmnd *scsi_cmd;
441         void (*done) (struct scsi_cmnd *);
442
443         unsigned long timeout;
444 };
445
446 struct ide_devset;
447 struct ide_driver_s;
448
449 #ifdef CONFIG_BLK_DEV_IDEACPI
450 struct ide_acpi_drive_link;
451 struct ide_acpi_hwif_link;
452 #endif
453
454 struct ide_drive_s;
455
456 struct ide_disk_ops {
457         int             (*check)(struct ide_drive_s *, const char *);
458         int             (*get_capacity)(struct ide_drive_s *);
459         void            (*setup)(struct ide_drive_s *);
460         void            (*flush)(struct ide_drive_s *);
461         int             (*init_media)(struct ide_drive_s *, struct gendisk *);
462         int             (*set_doorlock)(struct ide_drive_s *, struct gendisk *,
463                                         int);
464         ide_startstop_t (*do_request)(struct ide_drive_s *, struct request *,
465                                       sector_t);
466         int             (*end_request)(struct ide_drive_s *, int, int);
467         int             (*ioctl)(struct ide_drive_s *, struct block_device *,
468                                  fmode_t, unsigned int, unsigned long);
469 };
470
471 /* ATAPI device flags */
472 enum {
473         IDE_AFLAG_DRQ_INTERRUPT         = (1 << 0),
474
475         /* ide-cd */
476         /* Drive cannot eject the disc. */
477         IDE_AFLAG_NO_EJECT              = (1 << 1),
478         /* Drive is a pre ATAPI 1.2 drive. */
479         IDE_AFLAG_PRE_ATAPI12           = (1 << 2),
480         /* TOC addresses are in BCD. */
481         IDE_AFLAG_TOCADDR_AS_BCD        = (1 << 3),
482         /* TOC track numbers are in BCD. */
483         IDE_AFLAG_TOCTRACKS_AS_BCD      = (1 << 4),
484         /*
485          * Drive does not provide data in multiples of SECTOR_SIZE
486          * when more than one interrupt is needed.
487          */
488         IDE_AFLAG_LIMIT_NFRAMES         = (1 << 5),
489         /* Saved TOC information is current. */
490         IDE_AFLAG_TOC_VALID             = (1 << 6),
491         /* We think that the drive door is locked. */
492         IDE_AFLAG_DOOR_LOCKED           = (1 << 7),
493         /* SET_CD_SPEED command is unsupported. */
494         IDE_AFLAG_NO_SPEED_SELECT       = (1 << 8),
495         IDE_AFLAG_VERTOS_300_SSD        = (1 << 9),
496         IDE_AFLAG_VERTOS_600_ESD        = (1 << 10),
497         IDE_AFLAG_SANYO_3CD             = (1 << 11),
498         IDE_AFLAG_FULL_CAPS_PAGE        = (1 << 12),
499         IDE_AFLAG_PLAY_AUDIO_OK         = (1 << 13),
500         IDE_AFLAG_LE_SPEED_FIELDS       = (1 << 14),
501
502         /* ide-floppy */
503         /* Avoid commands not supported in Clik drive */
504         IDE_AFLAG_CLIK_DRIVE            = (1 << 15),
505         /* Requires BH algorithm for packets */
506         IDE_AFLAG_ZIP_DRIVE             = (1 << 16),
507         /* Supports format progress report */
508         IDE_AFLAG_SRFP                  = (1 << 17),
509
510         /* ide-tape */
511         IDE_AFLAG_IGNORE_DSC            = (1 << 18),
512         /* 0 When the tape position is unknown */
513         IDE_AFLAG_ADDRESS_VALID         = (1 << 19),
514         /* Device already opened */
515         IDE_AFLAG_BUSY                  = (1 << 20),
516         /* Attempt to auto-detect the current user block size */
517         IDE_AFLAG_DETECT_BS             = (1 << 21),
518         /* Currently on a filemark */
519         IDE_AFLAG_FILEMARK              = (1 << 22),
520         /* 0 = no tape is loaded, so we don't rewind after ejecting */
521         IDE_AFLAG_MEDIUM_PRESENT        = (1 << 23),
522
523         IDE_AFLAG_NO_AUTOCLOSE          = (1 << 24),
524 };
525
526 /* device flags */
527 enum {
528         /* restore settings after device reset */
529         IDE_DFLAG_KEEP_SETTINGS         = (1 << 0),
530         /* device is using DMA for read/write */
531         IDE_DFLAG_USING_DMA             = (1 << 1),
532         /* okay to unmask other IRQs */
533         IDE_DFLAG_UNMASK                = (1 << 2),
534         /* don't attempt flushes */
535         IDE_DFLAG_NOFLUSH               = (1 << 3),
536         /* DSC overlap */
537         IDE_DFLAG_DSC_OVERLAP           = (1 << 4),
538         /* give potential excess bandwidth */
539         IDE_DFLAG_NICE1                 = (1 << 5),
540         /* device is physically present */
541         IDE_DFLAG_PRESENT               = (1 << 6),
542         /* device ejected hint */
543         IDE_DFLAG_DEAD                  = (1 << 7),
544         /* id read from device (synthetic if not set) */
545         IDE_DFLAG_ID_READ               = (1 << 8),
546         IDE_DFLAG_NOPROBE               = (1 << 9),
547         /* need to do check_media_change() */
548         IDE_DFLAG_REMOVABLE             = (1 << 10),
549         /* needed for removable devices */
550         IDE_DFLAG_ATTACH                = (1 << 11),
551         IDE_DFLAG_FORCED_GEOM           = (1 << 12),
552         /* disallow setting unmask bit */
553         IDE_DFLAG_NO_UNMASK             = (1 << 13),
554         /* disallow enabling 32-bit I/O */
555         IDE_DFLAG_NO_IO_32BIT           = (1 << 14),
556         /* for removable only: door lock/unlock works */
557         IDE_DFLAG_DOORLOCKING           = (1 << 15),
558         /* disallow DMA */
559         IDE_DFLAG_NODMA                 = (1 << 16),
560         /* powermanagment told us not to do anything, so sleep nicely */
561         IDE_DFLAG_BLOCKED               = (1 << 17),
562         /* sleeping & sleep field valid */
563         IDE_DFLAG_SLEEPING              = (1 << 18),
564         IDE_DFLAG_POST_RESET            = (1 << 19),
565         IDE_DFLAG_UDMA33_WARNED         = (1 << 20),
566         IDE_DFLAG_LBA48                 = (1 << 21),
567         /* status of write cache */
568         IDE_DFLAG_WCACHE                = (1 << 22),
569         /* used for ignoring ATA_DF */
570         IDE_DFLAG_NOWERR                = (1 << 23),
571         /* retrying in PIO */
572         IDE_DFLAG_DMA_PIO_RETRY         = (1 << 24),
573         IDE_DFLAG_LBA                   = (1 << 25),
574         /* don't unload heads */
575         IDE_DFLAG_NO_UNLOAD             = (1 << 26),
576         /* heads unloaded, please don't reset port */
577         IDE_DFLAG_PARKED                = (1 << 27),
578         IDE_DFLAG_MEDIA_CHANGED         = (1 << 28),
579         /* write protect */
580         IDE_DFLAG_WP                    = (1 << 29),
581         IDE_DFLAG_FORMAT_IN_PROGRESS    = (1 << 30),
582 };
583
584 struct ide_drive_s {
585         char            name[4];        /* drive name, such as "hda" */
586         char            driver_req[10]; /* requests specific driver */
587
588         struct request_queue    *queue; /* request queue */
589
590         struct request          *rq;    /* current request */
591         void            *driver_data;   /* extra driver data */
592         u16                     *id;    /* identification info */
593 #ifdef CONFIG_IDE_PROC_FS
594         struct proc_dir_entry *proc;    /* /proc/ide/ directory entry */
595         const struct ide_proc_devset *settings; /* /proc/ide/ drive settings */
596 #endif
597         struct hwif_s           *hwif;  /* actually (ide_hwif_t *) */
598
599         const struct ide_disk_ops *disk_ops;
600
601         unsigned long dev_flags;
602
603         unsigned long sleep;            /* sleep until this time */
604         unsigned long timeout;          /* max time to wait for irq */
605
606         special_t       special;        /* special action flags */
607
608         u8      select;                 /* basic drive/head select reg value */
609         u8      retry_pio;              /* retrying dma capable host in pio */
610         u8      waiting_for_dma;        /* dma currently in progress */
611         u8      dma;                    /* atapi dma flag */
612
613         u8      quirk_list;     /* considered quirky, set for a specific host */
614         u8      init_speed;     /* transfer rate set at boot */
615         u8      current_speed;  /* current transfer rate set */
616         u8      desired_speed;  /* desired transfer rate set */
617         u8      dn;             /* now wide spread use */
618         u8      acoustic;       /* acoustic management */
619         u8      media;          /* disk, cdrom, tape, floppy, ... */
620         u8      ready_stat;     /* min status value for drive ready */
621         u8      mult_count;     /* current multiple sector setting */
622         u8      mult_req;       /* requested multiple sector setting */
623         u8      io_32bit;       /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
624         u8      bad_wstat;      /* used for ignoring ATA_DF */
625         u8      head;           /* "real" number of heads */
626         u8      sect;           /* "real" sectors per track */
627         u8      bios_head;      /* BIOS/fdisk/LILO number of heads */
628         u8      bios_sect;      /* BIOS/fdisk/LILO sectors per track */
629
630         /* delay this long before sending packet command */
631         u8 pc_delay;
632
633         unsigned int    bios_cyl;       /* BIOS/fdisk/LILO number of cyls */
634         unsigned int    cyl;            /* "real" number of cyls */
635         unsigned int    drive_data;     /* used by set_pio_mode/selectproc */
636         unsigned int    failures;       /* current failure count */
637         unsigned int    max_failures;   /* maximum allowed failure count */
638         u64             probed_capacity;/* initial reported media capacity (ide-cd only currently) */
639
640         u64             capacity64;     /* total number of sectors */
641
642         int             lun;            /* logical unit */
643         int             crc_count;      /* crc counter to reduce drive speed */
644
645         unsigned long   debug_mask;     /* debugging levels switch */
646
647 #ifdef CONFIG_BLK_DEV_IDEACPI
648         struct ide_acpi_drive_link *acpidata;
649 #endif
650         struct list_head list;
651         struct device   gendev;
652         struct completion gendev_rel_comp;      /* to deal with device release() */
653
654         /* current packet command */
655         struct ide_atapi_pc *pc;
656
657         /* callback for packet commands */
658         void (*pc_callback)(struct ide_drive_s *, int);
659
660         void (*pc_update_buffers)(struct ide_drive_s *, struct ide_atapi_pc *);
661         int  (*pc_io_buffers)(struct ide_drive_s *, struct ide_atapi_pc *,
662                               unsigned int, int);
663
664         unsigned long atapi_flags;
665
666         struct ide_atapi_pc request_sense_pc;
667         struct request request_sense_rq;
668 };
669
670 typedef struct ide_drive_s ide_drive_t;
671
672 #define to_ide_device(dev)              container_of(dev, ide_drive_t, gendev)
673
674 #define to_ide_drv(obj, cont_type)      \
675         container_of(obj, struct cont_type, kref)
676
677 #define ide_drv_g(disk, cont_type)      \
678         container_of((disk)->private_data, struct cont_type, driver)
679
680 struct ide_port_info;
681
682 struct ide_tp_ops {
683         void    (*exec_command)(struct hwif_s *, u8);
684         u8      (*read_status)(struct hwif_s *);
685         u8      (*read_altstatus)(struct hwif_s *);
686         u8      (*read_sff_dma_status)(struct hwif_s *);
687
688         void    (*set_irq)(struct hwif_s *, int);
689
690         void    (*tf_load)(ide_drive_t *, struct ide_task_s *);
691         void    (*tf_read)(ide_drive_t *, struct ide_task_s *);
692
693         void    (*input_data)(ide_drive_t *, struct request *, void *,
694                               unsigned int);
695         void    (*output_data)(ide_drive_t *, struct request *, void *,
696                                unsigned int);
697 };
698
699 extern const struct ide_tp_ops default_tp_ops;
700
701 /**
702  * struct ide_port_ops - IDE port operations
703  *
704  * @init_dev:           host specific initialization of a device
705  * @set_pio_mode:       routine to program host for PIO mode
706  * @set_dma_mode:       routine to program host for DMA mode
707  * @selectproc:         tweaks hardware to select drive
708  * @reset_poll:         chipset polling based on hba specifics
709  * @pre_reset:          chipset specific changes to default for device-hba resets
710  * @resetproc:          routine to reset controller after a disk reset
711  * @maskproc:           special host masking for drive selection
712  * @quirkproc:          check host's drive quirk list
713  * @clear_irq:          clear IRQ
714  *
715  * @mdma_filter:        filter MDMA modes
716  * @udma_filter:        filter UDMA modes
717  *
718  * @cable_detect:       detect cable type
719  */
720 struct ide_port_ops {
721         void    (*init_dev)(ide_drive_t *);
722         void    (*set_pio_mode)(ide_drive_t *, const u8);
723         void    (*set_dma_mode)(ide_drive_t *, const u8);
724         void    (*selectproc)(ide_drive_t *);
725         int     (*reset_poll)(ide_drive_t *);
726         void    (*pre_reset)(ide_drive_t *);
727         void    (*resetproc)(ide_drive_t *);
728         void    (*maskproc)(ide_drive_t *, int);
729         void    (*quirkproc)(ide_drive_t *);
730         void    (*clear_irq)(ide_drive_t *);
731
732         u8      (*mdma_filter)(ide_drive_t *);
733         u8      (*udma_filter)(ide_drive_t *);
734
735         u8      (*cable_detect)(struct hwif_s *);
736 };
737
738 struct ide_dma_ops {
739         void    (*dma_host_set)(struct ide_drive_s *, int);
740         int     (*dma_setup)(struct ide_drive_s *);
741         void    (*dma_exec_cmd)(struct ide_drive_s *, u8);
742         void    (*dma_start)(struct ide_drive_s *);
743         int     (*dma_end)(struct ide_drive_s *);
744         int     (*dma_test_irq)(struct ide_drive_s *);
745         void    (*dma_lost_irq)(struct ide_drive_s *);
746         void    (*dma_timeout)(struct ide_drive_s *);
747 };
748
749 struct ide_host;
750
751 typedef struct hwif_s {
752         struct hwif_s *mate;            /* other hwif from same PCI chip */
753         struct hwgroup_s *hwgroup;      /* actually (ide_hwgroup_t *) */
754         struct proc_dir_entry *proc;    /* /proc/ide/ directory entry */
755
756         struct ide_host *host;
757
758         char name[6];                   /* name of interface, eg. "ide0" */
759
760         struct ide_io_ports     io_ports;
761
762         unsigned long   sata_scr[SATA_NR_PORTS];
763
764         ide_drive_t     drives[MAX_DRIVES];     /* drive info */
765
766         u8 major;       /* our major number */
767         u8 index;       /* 0 for ide0; 1 for ide1; ... */
768         u8 channel;     /* for dual-port chips: 0=primary, 1=secondary */
769
770         u32 host_flags;
771
772         u8 pio_mask;
773
774         u8 ultra_mask;
775         u8 mwdma_mask;
776         u8 swdma_mask;
777
778         u8 cbl;         /* cable type */
779
780         hwif_chipset_t chipset; /* sub-module for tuning.. */
781
782         struct device *dev;
783
784         ide_ack_intr_t *ack_intr;
785
786         void (*rw_disk)(ide_drive_t *, struct request *);
787
788         const struct ide_tp_ops         *tp_ops;
789         const struct ide_port_ops       *port_ops;
790         const struct ide_dma_ops        *dma_ops;
791
792         /* dma physical region descriptor table (cpu view) */
793         unsigned int    *dmatable_cpu;
794         /* dma physical region descriptor table (dma view) */
795         dma_addr_t      dmatable_dma;
796
797         /* maximum number of PRD table entries */
798         int prd_max_nents;
799         /* PRD entry size in bytes */
800         int prd_ent_size;
801
802         /* Scatter-gather list used to build the above */
803         struct scatterlist *sg_table;
804         int sg_max_nents;               /* Maximum number of entries in it */
805         int sg_nents;                   /* Current number of entries in it */
806         int sg_dma_direction;           /* dma transfer direction */
807
808         /* data phase of the active command (currently only valid for PIO/DMA) */
809         int             data_phase;
810
811         struct ide_task_s task;         /* current command */
812
813         unsigned int nsect;
814         unsigned int nleft;
815         struct scatterlist *cursg;
816         unsigned int cursg_ofs;
817
818         int             rqsize;         /* max sectors per request */
819         int             irq;            /* our irq number */
820
821         unsigned long   dma_base;       /* base addr for dma ports */
822
823         unsigned long   config_data;    /* for use by chipset-specific code */
824         unsigned long   select_data;    /* for use by chipset-specific code */
825
826         unsigned long   extra_base;     /* extra addr for dma ports */
827         unsigned        extra_ports;    /* number of extra dma ports */
828
829         unsigned        present    : 1; /* this interface exists */
830         unsigned        sg_mapped  : 1; /* sg_table and sg_nents are ready */
831         unsigned        busy       : 1; /* serializes devices on a port */
832
833         struct device           gendev;
834         struct device           *portdev;
835
836         struct completion gendev_rel_comp; /* To deal with device release() */
837
838         void            *hwif_data;     /* extra hwif data */
839
840 #ifdef CONFIG_BLK_DEV_IDEACPI
841         struct ide_acpi_hwif_link *acpidata;
842 #endif
843 } ____cacheline_internodealigned_in_smp ide_hwif_t;
844
845 #define MAX_HOST_PORTS 4
846
847 struct ide_host {
848         ide_hwif_t      *ports[MAX_HOST_PORTS];
849         unsigned int    n_ports;
850         struct device   *dev[2];
851         unsigned int    (*init_chipset)(struct pci_dev *);
852         unsigned long   host_flags;
853         void            *host_priv;
854         ide_hwif_t      *cur_port;      /* for hosts requiring serialization */
855
856         /* used for hosts requiring serialization */
857         volatile long   host_busy;
858 };
859
860 #define IDE_HOST_BUSY 0
861
862 /*
863  *  internal ide interrupt handler type
864  */
865 typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
866 typedef int (ide_expiry_t)(ide_drive_t *);
867
868 /* used by ide-cd, ide-floppy, etc. */
869 typedef void (xfer_func_t)(ide_drive_t *, struct request *rq, void *, unsigned);
870
871 typedef struct hwgroup_s {
872                 /* irq handler, if active */
873         ide_startstop_t (*handler)(ide_drive_t *);
874
875                 /* BOOL: polling active & poll_timeout field valid */
876         unsigned int polling    : 1;
877
878                 /* current drive */
879         ide_drive_t *cur_dev;
880
881                 /* current request */
882         struct request *rq;
883
884                 /* failsafe timer */
885         struct timer_list timer;
886                 /* timeout value during long polls */
887         unsigned long poll_timeout;
888                 /* queried upon timeouts */
889         int (*expiry)(ide_drive_t *);
890
891         int req_gen;
892         int req_gen_timer;
893
894         spinlock_t lock;
895
896         int port_count;
897 } ide_hwgroup_t;
898
899 typedef struct ide_driver_s ide_driver_t;
900
901 extern struct mutex ide_setting_mtx;
902
903 /*
904  * configurable drive settings
905  */
906
907 #define DS_SYNC (1 << 0)
908
909 struct ide_devset {
910         int             (*get)(ide_drive_t *);
911         int             (*set)(ide_drive_t *, int);
912         unsigned int    flags;
913 };
914
915 #define __DEVSET(_flags, _get, _set) { \
916         .flags  = _flags, \
917         .get    = _get, \
918         .set    = _set, \
919 }
920
921 #define ide_devset_get(name, field) \
922 static int get_##name(ide_drive_t *drive) \
923 { \
924         return drive->field; \
925 }
926
927 #define ide_devset_set(name, field) \
928 static int set_##name(ide_drive_t *drive, int arg) \
929 { \
930         drive->field = arg; \
931         return 0; \
932 }
933
934 #define ide_devset_get_flag(name, flag) \
935 static int get_##name(ide_drive_t *drive) \
936 { \
937         return !!(drive->dev_flags & flag); \
938 }
939
940 #define ide_devset_set_flag(name, flag) \
941 static int set_##name(ide_drive_t *drive, int arg) \
942 { \
943         if (arg) \
944                 drive->dev_flags |= flag; \
945         else \
946                 drive->dev_flags &= ~flag; \
947         return 0; \
948 }
949
950 #define __IDE_DEVSET(_name, _flags, _get, _set) \
951 const struct ide_devset ide_devset_##_name = \
952         __DEVSET(_flags, _get, _set)
953
954 #define IDE_DEVSET(_name, _flags, _get, _set) \
955 static __IDE_DEVSET(_name, _flags, _get, _set)
956
957 #define ide_devset_rw(_name, _func) \
958 IDE_DEVSET(_name, 0, get_##_func, set_##_func)
959
960 #define ide_devset_w(_name, _func) \
961 IDE_DEVSET(_name, 0, NULL, set_##_func)
962
963 #define ide_ext_devset_rw(_name, _func) \
964 __IDE_DEVSET(_name, 0, get_##_func, set_##_func)
965
966 #define ide_ext_devset_rw_sync(_name, _func) \
967 __IDE_DEVSET(_name, DS_SYNC, get_##_func, set_##_func)
968
969 #define ide_decl_devset(_name) \
970 extern const struct ide_devset ide_devset_##_name
971
972 ide_decl_devset(io_32bit);
973 ide_decl_devset(keepsettings);
974 ide_decl_devset(pio_mode);
975 ide_decl_devset(unmaskirq);
976 ide_decl_devset(using_dma);
977
978 #ifdef CONFIG_IDE_PROC_FS
979 /*
980  * /proc/ide interface
981  */
982
983 #define ide_devset_rw_field(_name, _field) \
984 ide_devset_get(_name, _field); \
985 ide_devset_set(_name, _field); \
986 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
987
988 #define ide_devset_rw_flag(_name, _field) \
989 ide_devset_get_flag(_name, _field); \
990 ide_devset_set_flag(_name, _field); \
991 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
992
993 struct ide_proc_devset {
994         const char              *name;
995         const struct ide_devset *setting;
996         int                     min, max;
997         int                     (*mulf)(ide_drive_t *);
998         int                     (*divf)(ide_drive_t *);
999 };
1000
1001 #define __IDE_PROC_DEVSET(_name, _min, _max, _mulf, _divf) { \
1002         .name = __stringify(_name), \
1003         .setting = &ide_devset_##_name, \
1004         .min = _min, \
1005         .max = _max, \
1006         .mulf = _mulf, \
1007         .divf = _divf, \
1008 }
1009
1010 #define IDE_PROC_DEVSET(_name, _min, _max) \
1011 __IDE_PROC_DEVSET(_name, _min, _max, NULL, NULL)
1012
1013 typedef struct {
1014         const char      *name;
1015         mode_t          mode;
1016         read_proc_t     *read_proc;
1017         write_proc_t    *write_proc;
1018 } ide_proc_entry_t;
1019
1020 void proc_ide_create(void);
1021 void proc_ide_destroy(void);
1022 void ide_proc_register_port(ide_hwif_t *);
1023 void ide_proc_port_register_devices(ide_hwif_t *);
1024 void ide_proc_unregister_device(ide_drive_t *);
1025 void ide_proc_unregister_port(ide_hwif_t *);
1026 void ide_proc_register_driver(ide_drive_t *, ide_driver_t *);
1027 void ide_proc_unregister_driver(ide_drive_t *, ide_driver_t *);
1028
1029 read_proc_t proc_ide_read_capacity;
1030 read_proc_t proc_ide_read_geometry;
1031
1032 /*
1033  * Standard exit stuff:
1034  */
1035 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
1036 {                                       \
1037         len -= off;                     \
1038         if (len < count) {              \
1039                 *eof = 1;               \
1040                 if (len <= 0)           \
1041                         return 0;       \
1042         } else                          \
1043                 len = count;            \
1044         *start = page + off;            \
1045         return len;                     \
1046 }
1047 #else
1048 static inline void proc_ide_create(void) { ; }
1049 static inline void proc_ide_destroy(void) { ; }
1050 static inline void ide_proc_register_port(ide_hwif_t *hwif) { ; }
1051 static inline void ide_proc_port_register_devices(ide_hwif_t *hwif) { ; }
1052 static inline void ide_proc_unregister_device(ide_drive_t *drive) { ; }
1053 static inline void ide_proc_unregister_port(ide_hwif_t *hwif) { ; }
1054 static inline void ide_proc_register_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
1055 static inline void ide_proc_unregister_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
1056 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
1057 #endif
1058
1059 enum {
1060         /* enter/exit functions */
1061         IDE_DBG_FUNC =                  (1 << 0),
1062         /* sense key/asc handling */
1063         IDE_DBG_SENSE =                 (1 << 1),
1064         /* packet commands handling */
1065         IDE_DBG_PC =                    (1 << 2),
1066         /* request handling */
1067         IDE_DBG_RQ =                    (1 << 3),
1068         /* driver probing/setup */
1069         IDE_DBG_PROBE =                 (1 << 4),
1070 };
1071
1072 /* DRV_NAME has to be defined in the driver before using the macro below */
1073 #define __ide_debug_log(lvl, fmt, args...)                      \
1074 {                                                               \
1075         if (unlikely(drive->debug_mask & lvl))                  \
1076                 printk(KERN_INFO DRV_NAME ": " fmt, ## args);   \
1077 }
1078
1079 /*
1080  * Power Management state machine (rq->pm->pm_step).
1081  *
1082  * For each step, the core calls ide_start_power_step() first.
1083  * This can return:
1084  *      - ide_stopped : In this case, the core calls us back again unless
1085  *                      step have been set to ide_power_state_completed.
1086  *      - ide_started : In this case, the channel is left busy until an
1087  *                      async event (interrupt) occurs.
1088  * Typically, ide_start_power_step() will issue a taskfile request with
1089  * do_rw_taskfile().
1090  *
1091  * Upon reception of the interrupt, the core will call ide_complete_power_step()
1092  * with the error code if any. This routine should update the step value
1093  * and return. It should not start a new request. The core will call
1094  * ide_start_power_step() for the new step value, unless step have been
1095  * set to IDE_PM_COMPLETED.
1096  */
1097 enum {
1098         IDE_PM_START_SUSPEND,
1099         IDE_PM_FLUSH_CACHE      = IDE_PM_START_SUSPEND,
1100         IDE_PM_STANDBY,
1101
1102         IDE_PM_START_RESUME,
1103         IDE_PM_RESTORE_PIO      = IDE_PM_START_RESUME,
1104         IDE_PM_IDLE,
1105         IDE_PM_RESTORE_DMA,
1106
1107         IDE_PM_COMPLETED,
1108 };
1109
1110 int generic_ide_suspend(struct device *, pm_message_t);
1111 int generic_ide_resume(struct device *);
1112
1113 void ide_complete_power_step(ide_drive_t *, struct request *);
1114 ide_startstop_t ide_start_power_step(ide_drive_t *, struct request *);
1115 void ide_complete_pm_request(ide_drive_t *, struct request *);
1116 void ide_check_pm_state(ide_drive_t *, struct request *);
1117
1118 /*
1119  * Subdrivers support.
1120  *
1121  * The gendriver.owner field should be set to the module owner of this driver.
1122  * The gendriver.name field should be set to the name of this driver
1123  */
1124 struct ide_driver_s {
1125         const char                      *version;
1126         ide_startstop_t (*do_request)(ide_drive_t *, struct request *, sector_t);
1127         int             (*end_request)(ide_drive_t *, int, int);
1128         ide_startstop_t (*error)(ide_drive_t *, struct request *rq, u8, u8);
1129         struct device_driver    gen_driver;
1130         int             (*probe)(ide_drive_t *);
1131         void            (*remove)(ide_drive_t *);
1132         void            (*resume)(ide_drive_t *);
1133         void            (*shutdown)(ide_drive_t *);
1134 #ifdef CONFIG_IDE_PROC_FS
1135         ide_proc_entry_t *              (*proc_entries)(ide_drive_t *);
1136         const struct ide_proc_devset *  (*proc_devsets)(ide_drive_t *);
1137 #endif
1138 };
1139
1140 #define to_ide_driver(drv) container_of(drv, ide_driver_t, gen_driver)
1141
1142 int ide_device_get(ide_drive_t *);
1143 void ide_device_put(ide_drive_t *);
1144
1145 struct ide_ioctl_devset {
1146         unsigned int    get_ioctl;
1147         unsigned int    set_ioctl;
1148         const struct ide_devset *setting;
1149 };
1150
1151 int ide_setting_ioctl(ide_drive_t *, struct block_device *, unsigned int,
1152                       unsigned long, const struct ide_ioctl_devset *);
1153
1154 int generic_ide_ioctl(ide_drive_t *, struct block_device *, unsigned, unsigned long);
1155
1156 extern int ide_vlb_clk;
1157 extern int ide_pci_clk;
1158
1159 extern int ide_end_request (ide_drive_t *drive, int uptodate, int nrsecs);
1160 int ide_end_dequeued_request(ide_drive_t *drive, struct request *rq,
1161                              int uptodate, int nr_sectors);
1162
1163 extern void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry);
1164
1165 void ide_execute_command(ide_drive_t *, u8, ide_handler_t *, unsigned int,
1166                          ide_expiry_t *);
1167
1168 void ide_execute_pkt_cmd(ide_drive_t *);
1169
1170 void ide_pad_transfer(ide_drive_t *, int, int);
1171
1172 ide_startstop_t __ide_error(ide_drive_t *, struct request *, u8, u8);
1173
1174 ide_startstop_t ide_error (ide_drive_t *drive, const char *msg, byte stat);
1175
1176 void ide_fix_driveid(u16 *);
1177
1178 extern void ide_fixstring(u8 *, const int, const int);
1179
1180 int ide_busy_sleep(ide_hwif_t *, unsigned long, int);
1181
1182 int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
1183
1184 extern ide_startstop_t ide_do_reset (ide_drive_t *);
1185
1186 extern int ide_devset_execute(ide_drive_t *drive,
1187                               const struct ide_devset *setting, int arg);
1188
1189 extern void ide_do_drive_cmd(ide_drive_t *, struct request *);
1190
1191 extern void ide_end_drive_cmd(ide_drive_t *, u8, u8);
1192
1193 void ide_tf_dump(const char *, struct ide_taskfile *);
1194
1195 void ide_exec_command(ide_hwif_t *, u8);
1196 u8 ide_read_status(ide_hwif_t *);
1197 u8 ide_read_altstatus(ide_hwif_t *);
1198 u8 ide_read_sff_dma_status(ide_hwif_t *);
1199
1200 void ide_set_irq(ide_hwif_t *, int);
1201
1202 void ide_tf_load(ide_drive_t *, ide_task_t *);
1203 void ide_tf_read(ide_drive_t *, ide_task_t *);
1204
1205 void ide_input_data(ide_drive_t *, struct request *, void *, unsigned int);
1206 void ide_output_data(ide_drive_t *, struct request *, void *, unsigned int);
1207
1208 int ide_io_buffers(ide_drive_t *, struct ide_atapi_pc *, unsigned int, int);
1209
1210 extern void SELECT_DRIVE(ide_drive_t *);
1211 void SELECT_MASK(ide_drive_t *, int);
1212
1213 u8 ide_read_error(ide_drive_t *);
1214 void ide_read_bcount_and_ireason(ide_drive_t *, u16 *, u8 *);
1215
1216 extern int drive_is_ready(ide_drive_t *);
1217
1218 void ide_pktcmd_tf_load(ide_drive_t *, u32, u16, u8);
1219
1220 int ide_check_atapi_device(ide_drive_t *, const char *);
1221
1222 void ide_init_pc(struct ide_atapi_pc *);
1223
1224 /* Disk head parking */
1225 extern wait_queue_head_t ide_park_wq;
1226 ssize_t ide_park_show(struct device *dev, struct device_attribute *attr,
1227                       char *buf);
1228 ssize_t ide_park_store(struct device *dev, struct device_attribute *attr,
1229                        const char *buf, size_t len);
1230
1231 /*
1232  * Special requests for ide-tape block device strategy routine.
1233  *
1234  * In order to service a character device command, we add special requests to
1235  * the tail of our block device request queue and wait for their completion.
1236  */
1237 enum {
1238         REQ_IDETAPE_PC1         = (1 << 0), /* packet command (first stage) */
1239         REQ_IDETAPE_PC2         = (1 << 1), /* packet command (second stage) */
1240         REQ_IDETAPE_READ        = (1 << 2),
1241         REQ_IDETAPE_WRITE       = (1 << 3),
1242 };
1243
1244 int ide_queue_pc_tail(ide_drive_t *, struct gendisk *, struct ide_atapi_pc *);
1245
1246 int ide_do_test_unit_ready(ide_drive_t *, struct gendisk *);
1247 int ide_do_start_stop(ide_drive_t *, struct gendisk *, int);
1248 int ide_set_media_lock(ide_drive_t *, struct gendisk *, int);
1249 void ide_create_request_sense_cmd(ide_drive_t *, struct ide_atapi_pc *);
1250 void ide_retry_pc(ide_drive_t *, struct gendisk *);
1251
1252 int ide_cd_expiry(ide_drive_t *);
1253
1254 int ide_cd_get_xferlen(struct request *);
1255
1256 ide_startstop_t ide_issue_pc(ide_drive_t *);
1257
1258 ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);
1259
1260 void task_end_request(ide_drive_t *, struct request *, u8);
1261
1262 int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *, u16);
1263 int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);
1264
1265 int ide_taskfile_ioctl(ide_drive_t *, unsigned int, unsigned long);
1266
1267 extern int ide_driveid_update(ide_drive_t *);
1268 extern int ide_config_drive_speed(ide_drive_t *, u8);
1269 extern u8 eighty_ninty_three (ide_drive_t *);
1270 extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);
1271
1272 extern int ide_wait_not_busy(ide_hwif_t *hwif, unsigned long timeout);
1273
1274 extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);
1275
1276 extern void ide_timer_expiry(unsigned long);
1277 extern irqreturn_t ide_intr(int irq, void *dev_id);
1278 extern void do_ide_request(struct request_queue *);
1279
1280 void ide_init_disk(struct gendisk *, ide_drive_t *);
1281
1282 #ifdef CONFIG_IDEPCI_PCIBUS_ORDER
1283 extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
1284 #define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
1285 #else
1286 #define ide_pci_register_driver(d) pci_register_driver(d)
1287 #endif
1288
1289 static inline int ide_pci_is_in_compatibility_mode(struct pci_dev *dev)
1290 {
1291         if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE && (dev->class & 5) != 5)
1292                 return 1;
1293         return 0;
1294 }
1295
1296 void ide_pci_setup_ports(struct pci_dev *, const struct ide_port_info *, int,
1297                          hw_regs_t *, hw_regs_t **);
1298 void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
1299
1300 #ifdef CONFIG_BLK_DEV_IDEDMA_PCI
1301 int ide_pci_set_master(struct pci_dev *, const char *);
1302 unsigned long ide_pci_dma_base(ide_hwif_t *, const struct ide_port_info *);
1303 int ide_pci_check_simplex(ide_hwif_t *, const struct ide_port_info *);
1304 int ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
1305 #else
1306 static inline int ide_hwif_setup_dma(ide_hwif_t *hwif,
1307                                      const struct ide_port_info *d)
1308 {
1309         return -EINVAL;
1310 }
1311 #endif
1312
1313 typedef struct ide_pci_enablebit_s {
1314         u8      reg;    /* byte pci reg holding the enable-bit */
1315         u8      mask;   /* mask to isolate the enable-bit */
1316         u8      val;    /* value of masked reg when "enabled" */
1317 } ide_pci_enablebit_t;
1318
1319 enum {
1320         /* Uses ISA control ports not PCI ones. */
1321         IDE_HFLAG_ISA_PORTS             = (1 << 0),
1322         /* single port device */
1323         IDE_HFLAG_SINGLE                = (1 << 1),
1324         /* don't use legacy PIO blacklist */
1325         IDE_HFLAG_PIO_NO_BLACKLIST      = (1 << 2),
1326         /* set for the second port of QD65xx */
1327         IDE_HFLAG_QD_2ND_PORT           = (1 << 3),
1328         /* use PIO8/9 for prefetch off/on */
1329         IDE_HFLAG_ABUSE_PREFETCH        = (1 << 4),
1330         /* use PIO6/7 for fast-devsel off/on */
1331         IDE_HFLAG_ABUSE_FAST_DEVSEL     = (1 << 5),
1332         /* use 100-102 and 200-202 PIO values to set DMA modes */
1333         IDE_HFLAG_ABUSE_DMA_MODES       = (1 << 6),
1334         /*
1335          * keep DMA setting when programming PIO mode, may be used only
1336          * for hosts which have separate PIO and DMA timings (ie. PMAC)
1337          */
1338         IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
1339         /* program host for the transfer mode after programming device */
1340         IDE_HFLAG_POST_SET_MODE         = (1 << 8),
1341         /* don't program host/device for the transfer mode ("smart" hosts) */
1342         IDE_HFLAG_NO_SET_MODE           = (1 << 9),
1343         /* trust BIOS for programming chipset/device for DMA */
1344         IDE_HFLAG_TRUST_BIOS_FOR_DMA    = (1 << 10),
1345         /* host is CS5510/CS5520 */
1346         IDE_HFLAG_CS5520                = (1 << 11),
1347         /* ATAPI DMA is unsupported */
1348         IDE_HFLAG_NO_ATAPI_DMA          = (1 << 12),
1349         /* set if host is a "non-bootable" controller */
1350         IDE_HFLAG_NON_BOOTABLE          = (1 << 13),
1351         /* host doesn't support DMA */
1352         IDE_HFLAG_NO_DMA                = (1 << 14),
1353         /* check if host is PCI IDE device before allowing DMA */
1354         IDE_HFLAG_NO_AUTODMA            = (1 << 15),
1355         /* host uses MMIO */
1356         IDE_HFLAG_MMIO                  = (1 << 16),
1357         /* no LBA48 */
1358         IDE_HFLAG_NO_LBA48              = (1 << 17),
1359         /* no LBA48 DMA */
1360         IDE_HFLAG_NO_LBA48_DMA          = (1 << 18),
1361         /* data FIFO is cleared by an error */
1362         IDE_HFLAG_ERROR_STOPS_FIFO      = (1 << 19),
1363         /* serialize ports */
1364         IDE_HFLAG_SERIALIZE             = (1 << 20),
1365         /* use legacy IRQs */
1366         IDE_HFLAG_LEGACY_IRQS           = (1 << 21),
1367         /* force use of legacy IRQs */
1368         IDE_HFLAG_FORCE_LEGACY_IRQS     = (1 << 22),
1369         /* host is TRM290 */
1370         IDE_HFLAG_TRM290                = (1 << 23),
1371         /* use 32-bit I/O ops */
1372         IDE_HFLAG_IO_32BIT              = (1 << 24),
1373         /* unmask IRQs */
1374         IDE_HFLAG_UNMASK_IRQS           = (1 << 25),
1375         IDE_HFLAG_BROKEN_ALTSTATUS      = (1 << 26),
1376         /* serialize ports if DMA is possible (for sl82c105) */
1377         IDE_HFLAG_SERIALIZE_DMA         = (1 << 27),
1378         /* force host out of "simplex" mode */
1379         IDE_HFLAG_CLEAR_SIMPLEX         = (1 << 28),
1380         /* DSC overlap is unsupported */
1381         IDE_HFLAG_NO_DSC                = (1 << 29),
1382         /* never use 32-bit I/O ops */
1383         IDE_HFLAG_NO_IO_32BIT           = (1 << 30),
1384         /* never unmask IRQs */
1385         IDE_HFLAG_NO_UNMASK_IRQS        = (1 << 31),
1386 };
1387
1388 #ifdef CONFIG_BLK_DEV_OFFBOARD
1389 # define IDE_HFLAG_OFF_BOARD    0
1390 #else
1391 # define IDE_HFLAG_OFF_BOARD    IDE_HFLAG_NON_BOOTABLE
1392 #endif
1393
1394 struct ide_port_info {
1395         char                    *name;
1396         unsigned int            (*init_chipset)(struct pci_dev *);
1397         void                    (*init_iops)(ide_hwif_t *);
1398         void                    (*init_hwif)(ide_hwif_t *);
1399         int                     (*init_dma)(ide_hwif_t *,
1400                                             const struct ide_port_info *);
1401
1402         const struct ide_tp_ops         *tp_ops;
1403         const struct ide_port_ops       *port_ops;
1404         const struct ide_dma_ops        *dma_ops;
1405
1406         ide_pci_enablebit_t     enablebits[2];
1407         hwif_chipset_t          chipset;
1408
1409         u16                     max_sectors;    /* if < than the default one */
1410
1411         u32                     host_flags;
1412         u8                      pio_mask;
1413         u8                      swdma_mask;
1414         u8                      mwdma_mask;
1415         u8                      udma_mask;
1416 };
1417
1418 int ide_pci_init_one(struct pci_dev *, const struct ide_port_info *, void *);
1419 int ide_pci_init_two(struct pci_dev *, struct pci_dev *,
1420                      const struct ide_port_info *, void *);
1421 void ide_pci_remove(struct pci_dev *);
1422
1423 #ifdef CONFIG_PM
1424 int ide_pci_suspend(struct pci_dev *, pm_message_t);
1425 int ide_pci_resume(struct pci_dev *);
1426 #else
1427 #define ide_pci_suspend NULL
1428 #define ide_pci_resume NULL
1429 #endif
1430
1431 void ide_map_sg(ide_drive_t *, struct request *);
1432 void ide_init_sg_cmd(ide_drive_t *, struct request *);
1433
1434 #define BAD_DMA_DRIVE           0
1435 #define GOOD_DMA_DRIVE          1
1436
1437 struct drive_list_entry {
1438         const char *id_model;
1439         const char *id_firmware;
1440 };
1441
1442 int ide_in_drive_list(u16 *, const struct drive_list_entry *);
1443
1444 #ifdef CONFIG_BLK_DEV_IDEDMA
1445 int ide_dma_good_drive(ide_drive_t *);
1446 int __ide_dma_bad_drive(ide_drive_t *);
1447 int ide_id_dma_bug(ide_drive_t *);
1448
1449 u8 ide_find_dma_mode(ide_drive_t *, u8);
1450
1451 static inline u8 ide_max_dma_mode(ide_drive_t *drive)
1452 {
1453         return ide_find_dma_mode(drive, XFER_UDMA_6);
1454 }
1455
1456 void ide_dma_off_quietly(ide_drive_t *);
1457 void ide_dma_off(ide_drive_t *);
1458 void ide_dma_on(ide_drive_t *);
1459 int ide_set_dma(ide_drive_t *);
1460 void ide_check_dma_crc(ide_drive_t *);
1461 ide_startstop_t ide_dma_intr(ide_drive_t *);
1462
1463 int ide_allocate_dma_engine(ide_hwif_t *);
1464 void ide_release_dma_engine(ide_hwif_t *);
1465
1466 int ide_build_sglist(ide_drive_t *, struct request *);
1467 void ide_destroy_dmatable(ide_drive_t *);
1468
1469 #ifdef CONFIG_BLK_DEV_IDEDMA_SFF
1470 int config_drive_for_dma(ide_drive_t *);
1471 extern int ide_build_dmatable(ide_drive_t *, struct request *);
1472 void ide_dma_host_set(ide_drive_t *, int);
1473 extern int ide_dma_setup(ide_drive_t *);
1474 void ide_dma_exec_cmd(ide_drive_t *, u8);
1475 extern void ide_dma_start(ide_drive_t *);
1476 int ide_dma_end(ide_drive_t *);
1477 int ide_dma_test_irq(ide_drive_t *);
1478 extern const struct ide_dma_ops sff_dma_ops;
1479 #else
1480 static inline int config_drive_for_dma(ide_drive_t *drive) { return 0; }
1481 #endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
1482
1483 void ide_dma_lost_irq(ide_drive_t *);
1484 void ide_dma_timeout(ide_drive_t *);
1485
1486 #else
1487 static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
1488 static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
1489 static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
1490 static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
1491 static inline void ide_dma_off(ide_drive_t *drive) { ; }
1492 static inline void ide_dma_on(ide_drive_t *drive) { ; }
1493 static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
1494 static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
1495 static inline void ide_check_dma_crc(ide_drive_t *drive) { ; }
1496 static inline void ide_release_dma_engine(ide_hwif_t *hwif) { ; }
1497 #endif /* CONFIG_BLK_DEV_IDEDMA */
1498
1499 #ifdef CONFIG_BLK_DEV_IDEACPI
1500 extern int ide_acpi_exec_tfs(ide_drive_t *drive);
1501 extern void ide_acpi_get_timing(ide_hwif_t *hwif);
1502 extern void ide_acpi_push_timing(ide_hwif_t *hwif);
1503 extern void ide_acpi_init(ide_hwif_t *hwif);
1504 void ide_acpi_port_init_devices(ide_hwif_t *);
1505 extern void ide_acpi_set_state(ide_hwif_t *hwif, int on);
1506 #else
1507 static inline int ide_acpi_exec_tfs(ide_drive_t *drive) { return 0; }
1508 static inline void ide_acpi_get_timing(ide_hwif_t *hwif) { ; }
1509 static inline void ide_acpi_push_timing(ide_hwif_t *hwif) { ; }
1510 static inline void ide_acpi_init(ide_hwif_t *hwif) { ; }
1511 static inline void ide_acpi_port_init_devices(ide_hwif_t *hwif) { ; }
1512 static inline void ide_acpi_set_state(ide_hwif_t *hwif, int on) {}
1513 #endif
1514
1515 void ide_remove_port_from_hwgroup(ide_hwif_t *);
1516 void ide_unregister(ide_hwif_t *);
1517
1518 void ide_register_region(struct gendisk *);
1519 void ide_unregister_region(struct gendisk *);
1520
1521 void ide_undecoded_slave(ide_drive_t *);
1522
1523 void ide_port_apply_params(ide_hwif_t *);
1524 int ide_sysfs_register_port(ide_hwif_t *);
1525
1526 struct ide_host *ide_host_alloc(const struct ide_port_info *, hw_regs_t **);
1527 void ide_host_free(struct ide_host *);
1528 int ide_host_register(struct ide_host *, const struct ide_port_info *,
1529                       hw_regs_t **);
1530 int ide_host_add(const struct ide_port_info *, hw_regs_t **,
1531                  struct ide_host **);
1532 void ide_host_remove(struct ide_host *);
1533 int ide_legacy_device_add(const struct ide_port_info *, unsigned long);
1534 void ide_port_unregister_devices(ide_hwif_t *);
1535 void ide_port_scan(ide_hwif_t *);
1536
1537 static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
1538 {
1539         return hwif->hwif_data;
1540 }
1541
1542 static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
1543 {
1544         hwif->hwif_data = data;
1545 }
1546
1547 const char *ide_xfer_verbose(u8 mode);
1548 extern void ide_toggle_bounce(ide_drive_t *drive, int on);
1549 extern int ide_set_xfer_rate(ide_drive_t *drive, u8 rate);
1550
1551 u64 ide_get_lba_addr(struct ide_taskfile *, int);
1552 u8 ide_dump_status(ide_drive_t *, const char *, u8);
1553
1554 struct ide_timing {
1555         u8  mode;
1556         u8  setup;      /* t1 */
1557         u16 act8b;      /* t2 for 8-bit io */
1558         u16 rec8b;      /* t2i for 8-bit io */
1559         u16 cyc8b;      /* t0 for 8-bit io */
1560         u16 active;     /* t2 or tD */
1561         u16 recover;    /* t2i or tK */
1562         u16 cycle;      /* t0 */
1563         u16 udma;       /* t2CYCTYP/2 */
1564 };
1565
1566 enum {
1567         IDE_TIMING_SETUP        = (1 << 0),
1568         IDE_TIMING_ACT8B        = (1 << 1),
1569         IDE_TIMING_REC8B        = (1 << 2),
1570         IDE_TIMING_CYC8B        = (1 << 3),
1571         IDE_TIMING_8BIT         = IDE_TIMING_ACT8B | IDE_TIMING_REC8B |
1572                                   IDE_TIMING_CYC8B,
1573         IDE_TIMING_ACTIVE       = (1 << 4),
1574         IDE_TIMING_RECOVER      = (1 << 5),
1575         IDE_TIMING_CYCLE        = (1 << 6),
1576         IDE_TIMING_UDMA         = (1 << 7),
1577         IDE_TIMING_ALL          = IDE_TIMING_SETUP | IDE_TIMING_8BIT |
1578                                   IDE_TIMING_ACTIVE | IDE_TIMING_RECOVER |
1579                                   IDE_TIMING_CYCLE | IDE_TIMING_UDMA,
1580 };
1581
1582 struct ide_timing *ide_timing_find_mode(u8);
1583 u16 ide_pio_cycle_time(ide_drive_t *, u8);
1584 void ide_timing_merge(struct ide_timing *, struct ide_timing *,
1585                       struct ide_timing *, unsigned int);
1586 int ide_timing_compute(ide_drive_t *, u8, struct ide_timing *, int, int);
1587
1588 int ide_scan_pio_blacklist(char *);
1589
1590 u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
1591
1592 int ide_set_pio_mode(ide_drive_t *, u8);
1593 int ide_set_dma_mode(ide_drive_t *, u8);
1594
1595 void ide_set_pio(ide_drive_t *, u8);
1596
1597 static inline void ide_set_max_pio(ide_drive_t *drive)
1598 {
1599         ide_set_pio(drive, 255);
1600 }
1601
1602 extern spinlock_t ide_lock;
1603 extern struct mutex ide_cfg_mtx;
1604
1605 #define local_irq_set(flags)    do { local_save_flags((flags)); local_irq_enable_in_hardirq(); } while (0)
1606
1607 char *ide_media_string(ide_drive_t *);
1608
1609 extern struct device_attribute ide_dev_attrs[];
1610 extern struct bus_type ide_bus_type;
1611 extern struct class *ide_port_class;
1612
1613 static inline void ide_dump_identify(u8 *id)
1614 {
1615         print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 2, id, 512, 0);
1616 }
1617
1618 static inline int hwif_to_node(ide_hwif_t *hwif)
1619 {
1620         return hwif->dev ? dev_to_node(hwif->dev) : -1;
1621 }
1622
1623 static inline ide_drive_t *ide_get_pair_dev(ide_drive_t *drive)
1624 {
1625         ide_drive_t *peer = &drive->hwif->drives[(drive->dn ^ 1) & 1];
1626
1627         return (peer->dev_flags & IDE_DFLAG_PRESENT) ? peer : NULL;
1628 }
1629 #endif /* _IDE_H */