SAFE public projects git trees. - safe/jmp/linux-2.6/blob - drivers/staging/slicoss/slicoss.c

   1 /**************************************************************************
   2  *
   3  * Copyright  2000-2006 Alacritech, Inc.  All rights reserved.
   4  *
   5  * Redistribution and use in source and binary forms, with or without
   6  * modification, are permitted provided that the following conditions
   7  * are met:
   8  *
   9  * 1. Redistributions of source code must retain the above copyright
  10  *    notice, this list of conditions and the following disclaimer.
  11  * 2. Redistributions in binary form must reproduce the above
  12  *    copyright notice, this list of conditions and the following
  13  *    disclaimer in the documentation and/or other materials provided
  14  *    with the distribution.
  15  *
  16  * Alternatively, this software may be distributed under the terms of the
  17  * GNU General Public License ("GPL") version 2 as published by the Free
  18  * Software Foundation.
  19  *
  20  * THIS SOFTWARE IS PROVIDED BY ALACRITECH, INC. ``AS IS'' AND ANY
  21  * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  22  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
  23  * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL ALACRITECH, INC. OR
  24  * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
  25  * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
  26  * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
  27  * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
  28  * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  29  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
  30  * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
  31  * SUCH DAMAGE.
  32  *
  33  * The views and conclusions contained in the software and documentation
  34  * are those of the authors and should not be interpreted as representing
  35  * official policies, either expressed or implied, of Alacritech, Inc.
  36  *
  37  **************************************************************************/
  38
  39 /*
  40  * FILENAME: slicoss.c
  41  *
  42  * The SLICOSS driver for Alacritech's IS-NIC products.
  43  *
  44  * This driver is supposed to support:
  45  *
  46  *      Mojave cards (single port PCI Gigabit) both copper and fiber
  47  *      Oasis cards (single and dual port PCI-x Gigabit) copper and fiber
  48  *      Kalahari cards (dual and quad port PCI-e Gigabit) copper and fiber
  49  *
  50  * The driver was acutally tested on Oasis and Kalahari cards.
  51  *
  52  *
  53  * NOTE: This is the standard, non-accelerated version of Alacritech's
  54  *       IS-NIC driver.
  55  */
  56
  57
  58 #define KLUDGE_FOR_4GB_BOUNDARY         1
  59 #define DEBUG_MICROCODE                 1
  60 #define DBG                             1
  61 #define SLIC_INTERRUPT_PROCESS_LIMIT    1
  62 #define SLIC_OFFLOAD_IP_CHECKSUM                1
  63 #define STATS_TIMER_INTERVAL                    2
  64 #define PING_TIMER_INTERVAL                         1
  65
  66 #include <linux/kernel.h>
  67 #include <linux/string.h>
  68 #include <linux/errno.h>
  69 #include <linux/ioport.h>
  70 #include <linux/slab.h>
  71 #include <linux/interrupt.h>
  72 #include <linux/timer.h>
  73 #include <linux/pci.h>
  74 #include <linux/spinlock.h>
  75 #include <linux/init.h>
  76 #include <linux/bitops.h>
  77 #include <linux/io.h>
  78 #include <linux/netdevice.h>
  79 #include <linux/etherdevice.h>
  80 #include <linux/skbuff.h>
  81 #include <linux/delay.h>
  82 #include <linux/debugfs.h>
  83 #include <linux/seq_file.h>
  84 #include <linux/kthread.h>
  85 #include <linux/module.h>
  86 #include <linux/moduleparam.h>
  87
  88 #include <linux/firmware.h>
  89 #include <linux/types.h>
  90 #include <linux/dma-mapping.h>
  91 #include <linux/mii.h>
  92 #include <linux/if_vlan.h>
  93 #include <asm/unaligned.h>
  94
  95 #include <linux/ethtool.h>
  96 #include <linux/uaccess.h>
  97 #include "slichw.h"
  98 #include "slic.h"
  99
 100 static struct net_device_stats *slic_get_stats(struct net_device *dev);
 101 static int slic_entry_open(struct net_device *dev);
 102 static int slic_entry_halt(struct net_device *dev);
 103 static int slic_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
 104 static int slic_xmit_start(struct sk_buff *skb, struct net_device *dev);
 105 static void slic_xmit_fail(struct adapter *adapter, struct sk_buff *skb,
 106                            void *cmd, u32 skbtype, u32 status);
 107 static void slic_config_pci(struct pci_dev *pcidev);
 108 static struct sk_buff *slic_rcvqueue_getnext(struct adapter *adapter);
 109 static int slic_mac_set_address(struct net_device *dev, void *ptr);
 110 static void slic_link_event_handler(struct adapter *adapter);
 111 static void slic_upr_request_complete(struct adapter *adapter, u32 isr);
 112 static int slic_rspqueue_init(struct adapter *adapter);
 113 static void slic_rspqueue_free(struct adapter *adapter);
 114 static struct slic_rspbuf *slic_rspqueue_getnext(struct adapter *adapter);
 115 static int slic_cmdq_init(struct adapter *adapter);
 116 static void slic_cmdq_free(struct adapter *adapter);
 117 static void slic_cmdq_reset(struct adapter *adapter);
 118 static void slic_cmdq_addcmdpage(struct adapter *adapter, u32 *page);
 119 static void slic_cmdq_getdone(struct adapter *adapter);
 120 static void slic_cmdq_putdone_irq(struct adapter *adapter,
 121                                   struct slic_hostcmd *cmd);
 122 static struct slic_hostcmd *slic_cmdq_getfree(struct adapter *adapter);
 123 static int slic_rcvqueue_init(struct adapter *adapter);
 124 static int slic_rcvqueue_fill(struct adapter *adapter);
 125 static u32 slic_rcvqueue_reinsert(struct adapter *adapter, struct sk_buff *skb);
 126 static void slic_rcvqueue_free(struct adapter *adapter);
 127 static void slic_adapter_set_hwaddr(struct adapter *adapter);
 128 static int slic_card_init(struct sliccard *card, struct adapter *adapter);
 129 static void slic_intagg_set(struct adapter *adapter, u32 value);
 130 static int slic_card_download(struct adapter *adapter);
 131 static u32 slic_card_locate(struct adapter *adapter);
 132 static int slic_if_init(struct adapter *adapter);
 133 static int slic_adapter_allocresources(struct adapter *adapter);
 134 static void slic_adapter_freeresources(struct adapter *adapter);
 135 static void slic_link_config(struct adapter *adapter, u32 linkspeed,
 136                              u32 linkduplex);
 137 static void slic_unmap_mmio_space(struct adapter *adapter);
 138 static void slic_card_cleanup(struct sliccard *card);
 139 static void slic_soft_reset(struct adapter *adapter);
 140 static bool slic_mac_filter(struct adapter *adapter,
 141                             struct ether_header *ether_frame);
 142 static void slic_mac_address_config(struct adapter *adapter);
 143 static void slic_mac_config(struct adapter *adapter);
 144 static void slic_mcast_set_mask(struct adapter *adapter);
 145 static void slic_config_set(struct adapter *adapter, bool linkchange);
 146 static void slic_config_clear(struct adapter *adapter);
 147 static void slic_config_get(struct adapter *adapter, u32 config,
 148                             u32 configh);
 149 static void slic_timer_load_check(ulong context);
 150 static void slic_assert_fail(void);
 151 static ushort slic_eeprom_cksum(char *m, int len);
 152 static void slic_upr_start(struct adapter *adapter);
 153 static void slic_link_upr_complete(struct adapter *adapter, u32 Isr);
 154 static int  slic_upr_request(struct adapter *adapter, u32 upr_request,
 155                              u32 upr_data, u32 upr_data_h, u32 upr_buffer,
 156                              u32 upr_buffer_h);
 157 static void slic_mcast_set_list(struct net_device *dev);
 158
 159
 160 static uint slic_first_init = 1;
 161 static char *slic_banner = "Alacritech SLIC Technology(tm) Server "\
 162                 "and Storage Accelerator (Non-Accelerated)";
 163
 164 static char *slic_proc_version = "2.0.351  2006/07/14 12:26:00";
 165 static char *slic_product_name = "SLIC Technology(tm) Server "\
 166                 "and Storage Accelerator (Non-Accelerated)";
 167 static char *slic_vendor = "Alacritech, Inc.";
 168
 169 static int slic_debug = 1;
 170 static int debug = -1;
 171 static struct net_device *head_netdevice;
 172
 173 static struct base_driver slic_global = { {}, 0, 0, 0, 1, NULL, NULL };
 174 static int intagg_delay = 100;
 175 static u32 dynamic_intagg;
 176 static unsigned int rcv_count;
 177 static struct dentry *slic_debugfs;
 178
 179 #define DRV_NAME          "slicoss"
 180 #define DRV_VERSION       "2.0.1"
 181 #define DRV_AUTHOR        "Alacritech, Inc. Engineering"
 182 #define DRV_DESCRIPTION   "Alacritech SLIC Techonology(tm) "\
 183                 "Non-Accelerated Driver"
 184 #define DRV_COPYRIGHT     "Copyright  2000-2006 Alacritech, Inc. "\
 185                 "All rights reserved."
 186 #define PFX                DRV_NAME " "
 187
 188 MODULE_AUTHOR(DRV_AUTHOR);
 189 MODULE_DESCRIPTION(DRV_DESCRIPTION);
 190 MODULE_LICENSE("Dual BSD/GPL");
 191
 192 module_param(dynamic_intagg, int, 0);
 193 MODULE_PARM_DESC(dynamic_intagg, "Dynamic Interrupt Aggregation Setting");
 194 module_param(intagg_delay, int, 0);
 195 MODULE_PARM_DESC(intagg_delay, "uSec Interrupt Aggregation Delay");
 196
 197 static struct pci_device_id slic_pci_tbl[] __devinitdata = {
 198         {PCI_VENDOR_ID_ALACRITECH,
 199          SLIC_1GB_DEVICE_ID,
 200          PCI_ANY_ID, PCI_ANY_ID,},
 201         {PCI_VENDOR_ID_ALACRITECH,
 202          SLIC_2GB_DEVICE_ID,
 203          PCI_ANY_ID, PCI_ANY_ID,},
 204         {0,}
 205 };
 206
 207 MODULE_DEVICE_TABLE(pci, slic_pci_tbl);
 208
 209 #ifdef ASSERT
 210 #undef ASSERT
 211 #endif
 212
 213 #ifndef ASSERT
 214 #define ASSERT(a) do {                                                  \
 215         if (!(a)) {                                                     \
 216                 printk(KERN_ERR "slicoss ASSERT() Failure: function %s" \
 217                         "line %d\n", __func__, __LINE__);               \
 218                 slic_assert_fail();                                     \
 219         }                                                               \
 220 } while (0)
 221 #endif
 222
 223
 224 #define SLIC_GET_SLIC_HANDLE(_adapter, _pslic_handle)                   \
 225 {                                                                       \
 226     spin_lock_irqsave(&_adapter->handle_lock.lock,                      \
 227                         _adapter->handle_lock.flags);                   \
 228     _pslic_handle  =  _adapter->pfree_slic_handles;                     \
 229     if (_pslic_handle) {                                                \
 230         ASSERT(_pslic_handle->type == SLIC_HANDLE_FREE);                \
 231         _adapter->pfree_slic_handles = _pslic_handle->next;             \
 232     }                                                                   \
 233     spin_unlock_irqrestore(&_adapter->handle_lock.lock,                 \
 234                         _adapter->handle_lock.flags);                   \
 235 }
 236
 237 #define SLIC_FREE_SLIC_HANDLE(_adapter, _pslic_handle)                  \
 238 {                                                                       \
 239     _pslic_handle->type = SLIC_HANDLE_FREE;                             \
 240     spin_lock_irqsave(&_adapter->handle_lock.lock,                      \
 241                         _adapter->handle_lock.flags);                   \
 242     _pslic_handle->next = _adapter->pfree_slic_handles;                 \
 243     _adapter->pfree_slic_handles = _pslic_handle;                       \
 244     spin_unlock_irqrestore(&_adapter->handle_lock.lock,                 \
 245                         _adapter->handle_lock.flags);                   \
 246 }
 247
 248 static void slic_debug_init(void);
 249 static void slic_debug_cleanup(void);
 250 static void slic_debug_adapter_create(struct adapter *adapter);
 251 static void slic_debug_adapter_destroy(struct adapter *adapter);
 252 static void slic_debug_card_create(struct sliccard *card);
 253 static void slic_debug_card_destroy(struct sliccard *card);
 254
 255 static inline void slic_reg32_write(void __iomem *reg, u32 value, bool flush)
 256 {
 257         writel(value, reg);
 258         if (flush)
 259                 mb();
 260 }
 261
 262 static inline void slic_reg64_write(struct adapter *adapter, void __iomem *reg,
 263                                     u32 value, void __iomem *regh, u32 paddrh,
 264                                     bool flush)
 265 {
 266         spin_lock_irqsave(&adapter->bit64reglock.lock,
 267                                 adapter->bit64reglock.flags);
 268         if (paddrh != adapter->curaddrupper) {
 269                 adapter->curaddrupper = paddrh;
 270                 writel(paddrh, regh);
 271         }
 272         writel(value, reg);
 273         if (flush)
 274                 mb();
 275         spin_unlock_irqrestore(&adapter->bit64reglock.lock,
 276                                 adapter->bit64reglock.flags);
 277 }
 278
 279 static void slic_init_driver(void)
 280 {
 281         if (slic_first_init) {
 282                 slic_first_init = 0;
 283                 spin_lock_init(&slic_global.driver_lock.lock);
 284                 slic_debug_init();
 285         }
 286 }
 287
 288 static void slic_init_adapter(struct net_device *netdev,
 289                               struct pci_dev *pcidev,
 290                               const struct pci_device_id *pci_tbl_entry,
 291                               void __iomem *memaddr, int chip_idx)
 292 {
 293         ushort index;
 294         struct slic_handle *pslic_handle;
 295         struct adapter *adapter = (struct adapter *)netdev_priv(netdev);
 296
 297 /*      adapter->pcidev = pcidev;*/
 298         adapter->vendid = pci_tbl_entry->vendor;
 299         adapter->devid = pci_tbl_entry->device;
 300         adapter->subsysid = pci_tbl_entry->subdevice;
 301         adapter->busnumber = pcidev->bus->number;
 302         adapter->slotnumber = ((pcidev->devfn >> 3) & 0x1F);
 303         adapter->functionnumber = (pcidev->devfn & 0x7);
 304         adapter->memorylength = pci_resource_len(pcidev, 0);
 305         adapter->slic_regs = (__iomem struct slic_regs *)memaddr;
 306         adapter->irq = pcidev->irq;
 307 /*      adapter->netdev = netdev;*/
 308         adapter->next_netdevice = head_netdevice;
 309         head_netdevice = netdev;
 310         adapter->chipid = chip_idx;
 311         adapter->port = 0;      /*adapter->functionnumber;*/
 312         adapter->cardindex = adapter->port;
 313         adapter->memorybase = memaddr;
 314         spin_lock_init(&adapter->upr_lock.lock);
 315         spin_lock_init(&adapter->bit64reglock.lock);
 316         spin_lock_init(&adapter->adapter_lock.lock);
 317         spin_lock_init(&adapter->reset_lock.lock);
 318         spin_lock_init(&adapter->handle_lock.lock);
 319
 320         adapter->card_size = 1;
 321         /*
 322           Initialize slic_handle array
 323         */
 324         ASSERT(SLIC_CMDQ_MAXCMDS <= 0xFFFF);
 325         /*
 326          Start with 1.  0 is an invalid host handle.
 327         */
 328         for (index = 1, pslic_handle = &adapter->slic_handles[1];
 329              index < SLIC_CMDQ_MAXCMDS; index++, pslic_handle++) {
 330
 331                 pslic_handle->token.handle_index = index;
 332                 pslic_handle->type = SLIC_HANDLE_FREE;
 333                 pslic_handle->next = adapter->pfree_slic_handles;
 334                 adapter->pfree_slic_handles = pslic_handle;
 335         }
 336         adapter->pshmem = (struct slic_shmem *)
 337                                         pci_alloc_consistent(adapter->pcidev,
 338                                         sizeof(struct slic_shmem),
 339                                         &adapter->
 340                                         phys_shmem);
 341         ASSERT(adapter->pshmem);
 342
 343         memset(adapter->pshmem, 0, sizeof(struct slic_shmem));
 344
 345         return;
 346 }
 347
 348 static const struct net_device_ops slic_netdev_ops = {
 349         .ndo_open               = slic_entry_open,
 350         .ndo_stop               = slic_entry_halt,
 351         .ndo_start_xmit         = slic_xmit_start,
 352         .ndo_do_ioctl           = slic_ioctl,
 353         .ndo_set_mac_address    = slic_mac_set_address,
 354         .ndo_get_stats          = slic_get_stats,
 355         .ndo_set_multicast_list = slic_mcast_set_list,
 356         .ndo_validate_addr      = eth_validate_addr,
 357         .ndo_set_mac_address    = eth_mac_addr,
 358         .ndo_change_mtu         = eth_change_mtu,
 359 };
 360
 361 static int __devinit slic_entry_probe(struct pci_dev *pcidev,
 362                                const struct pci_device_id *pci_tbl_entry)
 363 {
 364         static int cards_found;
 365         static int did_version;
 366         int err = -ENODEV;
 367         struct net_device *netdev;
 368         struct adapter *adapter;
 369         void __iomem *memmapped_ioaddr = NULL;
 370         u32 status = 0;
 371         ulong mmio_start = 0;
 372         ulong mmio_len = 0;
 373         struct sliccard *card = NULL;
 374
 375         slic_global.dynamic_intagg = dynamic_intagg;
 376
 377         err = pci_enable_device(pcidev);
 378
 379         if (err)
 380                 return err;
 381
 382         if (slic_debug > 0 && did_version++ == 0) {
 383                 printk(KERN_DEBUG "%s\n", slic_banner);
 384                 printk(KERN_DEBUG "%s\n", slic_proc_version);
 385         }
 386
 387         err = pci_set_dma_mask(pcidev, DMA_BIT_MASK(64));
 388         if (err) {
 389                 err = pci_set_dma_mask(pcidev, DMA_BIT_MASK(32));
 390                 if (err)
 391                         goto err_out_disable_pci;
 392         }
 393
 394         err = pci_request_regions(pcidev, DRV_NAME);
 395         if (err)
 396                 goto err_out_disable_pci;
 397
 398         pci_set_master(pcidev);
 399
 400         netdev = alloc_etherdev(sizeof(struct adapter));
 401         if (!netdev) {
 402                 err = -ENOMEM;
 403                 goto err_out_exit_slic_probe;
 404         }
 405
 406         SET_NETDEV_DEV(netdev, &pcidev->dev);
 407
 408         pci_set_drvdata(pcidev, netdev);
 409         adapter = netdev_priv(netdev);
 410         adapter->netdev = netdev;
 411         adapter->pcidev = pcidev;
 412
 413         mmio_start = pci_resource_start(pcidev, 0);
 414         mmio_len = pci_resource_len(pcidev, 0);
 415
 416
 417 /*      memmapped_ioaddr =  (u32)ioremap_nocache(mmio_start, mmio_len);*/
 418         memmapped_ioaddr = ioremap(mmio_start, mmio_len);
 419         if (!memmapped_ioaddr) {
 420                 dev_err(&pcidev->dev, "cannot remap MMIO region %lx @ %lx\n",
 421                         mmio_len, mmio_start);
 422                 goto err_out_free_netdev;
 423         }
 424
 425         slic_config_pci(pcidev);
 426
 427         slic_init_driver();
 428
 429         slic_init_adapter(netdev,
 430                           pcidev, pci_tbl_entry, memmapped_ioaddr, cards_found);
 431
 432         status = slic_card_locate(adapter);
 433         if (status) {
 434                 dev_err(&pcidev->dev, "cannot locate card\n");
 435                 goto err_out_free_mmio_region;
 436         }
 437
 438         card = adapter->card;
 439
 440         if (!adapter->allocated) {
 441                 card->adapters_allocated++;
 442                 adapter->allocated = 1;
 443         }
 444
 445         status = slic_card_init(card, adapter);
 446
 447         if (status != STATUS_SUCCESS) {
 448                 card->state = CARD_FAIL;
 449                 adapter->state = ADAPT_FAIL;
 450                 adapter->linkstate = LINK_DOWN;
 451                 dev_err(&pcidev->dev, "FAILED status[%x]\n", status);
 452         } else {
 453                 slic_adapter_set_hwaddr(adapter);
 454         }
 455
 456         netdev->base_addr = (unsigned long)adapter->memorybase;
 457         netdev->irq = adapter->irq;
 458         netdev->netdev_ops = &slic_netdev_ops;
 459
 460         slic_debug_adapter_create(adapter);
 461
 462         strcpy(netdev->name, "eth%d");
 463         err = register_netdev(netdev);
 464         if (err) {
 465                 dev_err(&pcidev->dev, "Cannot register net device, aborting.\n");
 466                 goto err_out_unmap;
 467         }
 468
 469         cards_found++;
 470
 471         return status;
 472
 473 err_out_unmap:
 474         iounmap(memmapped_ioaddr);
 475 err_out_free_mmio_region:
 476         release_mem_region(mmio_start, mmio_len);
 477 err_out_free_netdev:
 478         free_netdev(netdev);
 479 err_out_exit_slic_probe:
 480         pci_release_regions(pcidev);
 481 err_out_disable_pci:
 482         pci_disable_device(pcidev);
 483         return err;
 484 }
 485
 486 static int slic_entry_open(struct net_device *dev)
 487 {
 488         struct adapter *adapter = (struct adapter *) netdev_priv(dev);
 489         struct sliccard *card = adapter->card;
 490         u32 locked = 0;
 491         int status;
 492
 493         ASSERT(adapter);
 494         ASSERT(card);
 495
 496         netif_stop_queue(adapter->netdev);
 497
 498         spin_lock_irqsave(&slic_global.driver_lock.lock,
 499                                 slic_global.driver_lock.flags);
 500         locked = 1;
 501         if (!adapter->activated) {
 502                 card->adapters_activated++;
 503                 slic_global.num_slic_ports_active++;
 504                 adapter->activated = 1;
 505         }
 506         status = slic_if_init(adapter);
 507
 508         if (status != STATUS_SUCCESS) {
 509                 if (adapter->activated) {
 510                         card->adapters_activated--;
 511                         slic_global.num_slic_ports_active--;
 512                         adapter->activated = 0;
 513                 }
 514                 if (locked) {
 515                         spin_unlock_irqrestore(&slic_global.driver_lock.lock,
 516                                                 slic_global.driver_lock.flags);
 517                         locked = 0;
 518                 }
 519                 return status;
 520         }
 521         if (!card->master)
 522                 card->master = adapter;
 523
 524         if (locked) {
 525                 spin_unlock_irqrestore(&slic_global.driver_lock.lock,
 526                                         slic_global.driver_lock.flags);
 527                 locked = 0;
 528         }
 529
 530         return STATUS_SUCCESS;
 531 }
 532
 533 static void __devexit slic_entry_remove(struct pci_dev *pcidev)
 534 {
 535         struct net_device *dev = pci_get_drvdata(pcidev);
 536         u32 mmio_start = 0;
 537         uint mmio_len = 0;
 538         struct adapter *adapter = (struct adapter *) netdev_priv(dev);
 539         struct sliccard *card;
 540         struct mcast_address *mcaddr, *mlist;
 541
 542         ASSERT(adapter);
 543         slic_adapter_freeresources(adapter);
 544         slic_unmap_mmio_space(adapter);
 545         unregister_netdev(dev);
 546
 547         mmio_start = pci_resource_start(pcidev, 0);
 548         mmio_len = pci_resource_len(pcidev, 0);
 549
 550         release_mem_region(mmio_start, mmio_len);
 551
 552         iounmap((void __iomem *)dev->base_addr);
 553         /* free multicast addresses */
 554         mlist = adapter->mcastaddrs;
 555         while (mlist) {
 556                 mcaddr = mlist;
 557                 mlist = mlist->next;
 558                 kfree(mcaddr);
 559         }
 560         ASSERT(adapter->card);
 561         card = adapter->card;
 562         ASSERT(card->adapters_allocated);
 563         card->adapters_allocated--;
 564         adapter->allocated = 0;
 565         if (!card->adapters_allocated) {
 566                 struct sliccard *curr_card = slic_global.slic_card;
 567                 if (curr_card == card) {
 568                         slic_global.slic_card = card->next;
 569                 } else {
 570                         while (curr_card->next != card)
 571                                 curr_card = curr_card->next;
 572                         ASSERT(curr_card);
 573                         curr_card->next = card->next;
 574                 }
 575                 ASSERT(slic_global.num_slic_cards);
 576                 slic_global.num_slic_cards--;
 577                 slic_card_cleanup(card);
 578         }
 579         kfree(dev);
 580         pci_release_regions(pcidev);
 581 }
 582
 583 static int slic_entry_halt(struct net_device *dev)
 584 {
 585         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
 586         struct sliccard *card = adapter->card;
 587         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
 588
 589         spin_lock_irqsave(&slic_global.driver_lock.lock,
 590                                 slic_global.driver_lock.flags);
 591         ASSERT(card);
 592         netif_stop_queue(adapter->netdev);
 593         adapter->state = ADAPT_DOWN;
 594         adapter->linkstate = LINK_DOWN;
 595         adapter->upr_list = NULL;
 596         adapter->upr_busy = 0;
 597         adapter->devflags_prev = 0;
 598         ASSERT(card->adapter[adapter->cardindex] == adapter);
 599         slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH);
 600         adapter->all_reg_writes++;
 601         adapter->icr_reg_writes++;
 602         slic_config_clear(adapter);
 603         if (adapter->activated) {
 604                 card->adapters_activated--;
 605                 slic_global.num_slic_ports_active--;
 606                 adapter->activated = 0;
 607         }
 608 #ifdef AUTOMATIC_RESET
 609         slic_reg32_write(&slic_regs->slic_reset_iface, 0, FLUSH);
 610 #endif
 611         /*
 612          *  Reset the adapter's cmd queues
 613          */
 614         slic_cmdq_reset(adapter);
 615
 616 #ifdef AUTOMATIC_RESET
 617         if (!card->adapters_activated)
 618                 slic_card_init(card, adapter);
 619 #endif
 620
 621         spin_unlock_irqrestore(&slic_global.driver_lock.lock,
 622                                 slic_global.driver_lock.flags);
 623         return STATUS_SUCCESS;
 624 }
 625
 626 static int slic_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 627 {
 628         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
 629         struct ethtool_cmd edata;
 630         struct ethtool_cmd ecmd;
 631         u32 data[7];
 632         u32 intagg;
 633
 634         ASSERT(rq);
 635         switch (cmd) {
 636         case SIOCSLICSETINTAGG:
 637                 if (copy_from_user(data, rq->ifr_data, 28))
 638                         return -EFAULT;
 639                 intagg = data[0];
 640                 dev_err(&dev->dev, "%s: set interrupt aggregation to %d\n",
 641                         __func__, intagg);
 642                 slic_intagg_set(adapter, intagg);
 643                 return 0;
 644
 645 #ifdef SLIC_TRACE_DUMP_ENABLED
 646         case SIOCSLICTRACEDUMP:
 647                 {
 648                         u32 value;
 649                         DBG_IOCTL("slic_ioctl  SIOCSLIC_TRACE_DUMP\n");
 650
 651                         if (copy_from_user(data, rq->ifr_data, 28)) {
 652                                 PRINT_ERROR
 653                                     ("slic: copy_from_user FAILED getting \
 654                                      initial simba param\n");
 655                                 return -EFAULT;
 656                         }
 657
 658                         value = data[0];
 659                         if (tracemon_request == SLIC_DUMP_DONE) {
 660                                 PRINT_ERROR
 661                                     ("ATK Diagnostic Trace Dump Requested\n");
 662                                 tracemon_request = SLIC_DUMP_REQUESTED;
 663                                 tracemon_request_type = value;
 664                                 tracemon_timestamp = jiffies;
 665                         } else if ((tracemon_request == SLIC_DUMP_REQUESTED) ||
 666                                    (tracemon_request ==
 667                                     SLIC_DUMP_IN_PROGRESS)) {
 668                                 PRINT_ERROR
 669                                     ("ATK Diagnostic Trace Dump Requested but \
 670                                      already in progress... ignore\n");
 671                         } else {
 672                                 PRINT_ERROR
 673                                     ("ATK Diagnostic Trace Dump Requested\n");
 674                                 tracemon_request = SLIC_DUMP_REQUESTED;
 675                                 tracemon_request_type = value;
 676                                 tracemon_timestamp = jiffies;
 677                         }
 678                         return 0;
 679                 }
 680 #endif
 681         case SIOCETHTOOL:
 682                 ASSERT(adapter);
 683                 if (copy_from_user(&ecmd, rq->ifr_data, sizeof(ecmd)))
 684                         return -EFAULT;
 685
 686                 if (ecmd.cmd == ETHTOOL_GSET) {
 687                         edata.supported = (SUPPORTED_10baseT_Half |
 688                                            SUPPORTED_10baseT_Full |
 689                                            SUPPORTED_100baseT_Half |
 690                                            SUPPORTED_100baseT_Full |
 691                                            SUPPORTED_Autoneg | SUPPORTED_MII);
 692                         edata.port = PORT_MII;
 693                         edata.transceiver = XCVR_INTERNAL;
 694                         edata.phy_address = 0;
 695                         if (adapter->linkspeed == LINK_100MB)
 696                                 edata.speed = SPEED_100;
 697                         else if (adapter->linkspeed == LINK_10MB)
 698                                 edata.speed = SPEED_10;
 699                         else
 700                                 edata.speed = 0;
 701
 702                         if (adapter->linkduplex == LINK_FULLD)
 703                                 edata.duplex = DUPLEX_FULL;
 704                         else
 705                                 edata.duplex = DUPLEX_HALF;
 706
 707                         edata.autoneg = AUTONEG_ENABLE;
 708                         edata.maxtxpkt = 1;
 709                         edata.maxrxpkt = 1;
 710                         if (copy_to_user(rq->ifr_data, &edata, sizeof(edata)))
 711                                 return -EFAULT;
 712
 713                 } else if (ecmd.cmd == ETHTOOL_SSET) {
 714                         if (!capable(CAP_NET_ADMIN))
 715                                 return -EPERM;
 716
 717                         if (adapter->linkspeed == LINK_100MB)
 718                                 edata.speed = SPEED_100;
 719                         else if (adapter->linkspeed == LINK_10MB)
 720                                 edata.speed = SPEED_10;
 721                         else
 722                                 edata.speed = 0;
 723
 724                         if (adapter->linkduplex == LINK_FULLD)
 725                                 edata.duplex = DUPLEX_FULL;
 726                         else
 727                                 edata.duplex = DUPLEX_HALF;
 728
 729                         edata.autoneg = AUTONEG_ENABLE;
 730                         edata.maxtxpkt = 1;
 731                         edata.maxrxpkt = 1;
 732                         if ((ecmd.speed != edata.speed) ||
 733                             (ecmd.duplex != edata.duplex)) {
 734                                 u32 speed;
 735                                 u32 duplex;
 736
 737                                 if (ecmd.speed == SPEED_10)
 738                                         speed = 0;
 739                                 else
 740                                         speed = PCR_SPEED_100;
 741                                 if (ecmd.duplex == DUPLEX_FULL)
 742                                         duplex = PCR_DUPLEX_FULL;
 743                                 else
 744                                         duplex = 0;
 745                                 slic_link_config(adapter, speed, duplex);
 746                                 slic_link_event_handler(adapter);
 747                         }
 748                 }
 749                 return 0;
 750         default:
 751                 return -EOPNOTSUPP;
 752         }
 753 }
 754
 755 #define  XMIT_FAIL_LINK_STATE               1
 756 #define  XMIT_FAIL_ZERO_LENGTH              2
 757 #define  XMIT_FAIL_HOSTCMD_FAIL             3
 758
 759 static void slic_xmit_build_request(struct adapter *adapter,
 760                              struct slic_hostcmd *hcmd, struct sk_buff *skb)
 761 {
 762         struct slic_host64_cmd *ihcmd;
 763         ulong phys_addr;
 764
 765         ihcmd = &hcmd->cmd64;
 766
 767         ihcmd->flags = (adapter->port << IHFLG_IFSHFT);
 768         ihcmd->command = IHCMD_XMT_REQ;
 769         ihcmd->u.slic_buffers.totlen = skb->len;
 770         phys_addr = pci_map_single(adapter->pcidev, skb->data, skb->len,
 771                         PCI_DMA_TODEVICE);
 772         ihcmd->u.slic_buffers.bufs[0].paddrl = SLIC_GET_ADDR_LOW(phys_addr);
 773         ihcmd->u.slic_buffers.bufs[0].paddrh = SLIC_GET_ADDR_HIGH(phys_addr);
 774         ihcmd->u.slic_buffers.bufs[0].length = skb->len;
 775 #if defined(CONFIG_X86_64)
 776         hcmd->cmdsize = (u32) ((((u64)&ihcmd->u.slic_buffers.bufs[1] -
 777                                      (u64) hcmd) + 31) >> 5);
 778 #elif defined(CONFIG_X86)
 779         hcmd->cmdsize = ((((u32) &ihcmd->u.slic_buffers.bufs[1] -
 780                            (u32) hcmd) + 31) >> 5);
 781 #else
 782         Stop Compilation;
 783 #endif
 784 }
 785
 786 #define NORMAL_ETHFRAME     0
 787
 788 static int slic_xmit_start(struct sk_buff *skb, struct net_device *dev)
 789 {
 790         struct sliccard *card;
 791         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
 792         struct slic_hostcmd *hcmd = NULL;
 793         u32 status = 0;
 794         u32 skbtype = NORMAL_ETHFRAME;
 795         void *offloadcmd = NULL;
 796
 797         card = adapter->card;
 798         ASSERT(card);
 799         if ((adapter->linkstate != LINK_UP) ||
 800             (adapter->state != ADAPT_UP) || (card->state != CARD_UP)) {
 801                 status = XMIT_FAIL_LINK_STATE;
 802                 goto xmit_fail;
 803
 804         } else if (skb->len == 0) {
 805                 status = XMIT_FAIL_ZERO_LENGTH;
 806                 goto xmit_fail;
 807         }
 808
 809         if (skbtype == NORMAL_ETHFRAME) {
 810                 hcmd = slic_cmdq_getfree(adapter);
 811                 if (!hcmd) {
 812                         adapter->xmitq_full = 1;
 813                         status = XMIT_FAIL_HOSTCMD_FAIL;
 814                         goto xmit_fail;
 815                 }
 816                 ASSERT(hcmd->pslic_handle);
 817                 ASSERT(hcmd->cmd64.hosthandle ==
 818                        hcmd->pslic_handle->token.handle_token);
 819                 hcmd->skb = skb;
 820                 hcmd->busy = 1;
 821                 hcmd->type = SLIC_CMD_DUMB;
 822                 if (skbtype == NORMAL_ETHFRAME)
 823                         slic_xmit_build_request(adapter, hcmd, skb);
 824         }
 825         adapter->stats.tx_packets++;
 826         adapter->stats.tx_bytes += skb->len;
 827
 828 #ifdef DEBUG_DUMP
 829         if (adapter->kill_card) {
 830                 struct slic_host64_cmd ihcmd;
 831
 832                 ihcmd = &hcmd->cmd64;
 833
 834                 ihcmd->flags |= 0x40;
 835                 adapter->kill_card = 0; /* only do this once */
 836         }
 837 #endif
 838         if (hcmd->paddrh == 0) {
 839                 slic_reg32_write(&adapter->slic_regs->slic_cbar,
 840                                  (hcmd->paddrl | hcmd->cmdsize), DONT_FLUSH);
 841         } else {
 842                 slic_reg64_write(adapter, &adapter->slic_regs->slic_cbar64,
 843                                  (hcmd->paddrl | hcmd->cmdsize),
 844                                  &adapter->slic_regs->slic_addr_upper,
 845                                  hcmd->paddrh, DONT_FLUSH);
 846         }
 847 xmit_done:
 848         return NETDEV_TX_OK;
 849 xmit_fail:
 850         slic_xmit_fail(adapter, skb, offloadcmd, skbtype, status);
 851         goto xmit_done;
 852 }
 853
 854 static void slic_xmit_fail(struct adapter *adapter,
 855                     struct sk_buff *skb,
 856                     void *cmd, u32 skbtype, u32 status)
 857 {
 858         if (adapter->xmitq_full)
 859                 netif_stop_queue(adapter->netdev);
 860         if ((cmd == NULL) && (status <= XMIT_FAIL_HOSTCMD_FAIL)) {
 861                 switch (status) {
 862                 case XMIT_FAIL_LINK_STATE:
 863                         dev_err(&adapter->netdev->dev,
 864                                 "reject xmit skb[%p: %x] linkstate[%s] "
 865                                 "adapter[%s:%d] card[%s:%d]\n",
 866                                 skb, skb->pkt_type,
 867                                 SLIC_LINKSTATE(adapter->linkstate),
 868                                 SLIC_ADAPTER_STATE(adapter->state),
 869                                 adapter->state,
 870                                 SLIC_CARD_STATE(adapter->card->state),
 871                                 adapter->card->state);
 872                         break;
 873                 case XMIT_FAIL_ZERO_LENGTH:
 874                         dev_err(&adapter->netdev->dev,
 875                                 "xmit_start skb->len == 0 skb[%p] type[%x]\n",
 876                                 skb, skb->pkt_type);
 877                         break;
 878                 case XMIT_FAIL_HOSTCMD_FAIL:
 879                         dev_err(&adapter->netdev->dev,
 880                                 "xmit_start skb[%p] type[%x] No host commands "
 881                                 "available\n", skb, skb->pkt_type);
 882                         break;
 883                 default:
 884                         ASSERT(0);
 885                 }
 886         }
 887         dev_kfree_skb(skb);
 888         adapter->stats.tx_dropped++;
 889 }
 890
 891 static void slic_rcv_handle_error(struct adapter *adapter,
 892                                         struct slic_rcvbuf *rcvbuf)
 893 {
 894         struct slic_hddr_wds *hdr = (struct slic_hddr_wds *)rcvbuf->data;
 895
 896         if (adapter->devid != SLIC_1GB_DEVICE_ID) {
 897                 if (hdr->frame_status14 & VRHSTAT_802OE)
 898                         adapter->if_events.oflow802++;
 899                 if (hdr->frame_status14 & VRHSTAT_TPOFLO)
 900                         adapter->if_events.Tprtoflow++;
 901                 if (hdr->frame_status_b14 & VRHSTATB_802UE)
 902                         adapter->if_events.uflow802++;
 903                 if (hdr->frame_status_b14 & VRHSTATB_RCVE) {
 904                         adapter->if_events.rcvearly++;
 905                         adapter->stats.rx_fifo_errors++;
 906                 }
 907                 if (hdr->frame_status_b14 & VRHSTATB_BUFF) {
 908                         adapter->if_events.Bufov++;
 909                         adapter->stats.rx_over_errors++;
 910                 }
 911                 if (hdr->frame_status_b14 & VRHSTATB_CARRE) {
 912                         adapter->if_events.Carre++;
 913                         adapter->stats.tx_carrier_errors++;
 914                 }
 915                 if (hdr->frame_status_b14 & VRHSTATB_LONGE)
 916                         adapter->if_events.Longe++;
 917                 if (hdr->frame_status_b14 & VRHSTATB_PREA)
 918                         adapter->if_events.Invp++;
 919                 if (hdr->frame_status_b14 & VRHSTATB_CRC) {
 920                         adapter->if_events.Crc++;
 921                         adapter->stats.rx_crc_errors++;
 922                 }
 923                 if (hdr->frame_status_b14 & VRHSTATB_DRBL)
 924                         adapter->if_events.Drbl++;
 925                 if (hdr->frame_status_b14 & VRHSTATB_CODE)
 926                         adapter->if_events.Code++;
 927                 if (hdr->frame_status_b14 & VRHSTATB_TPCSUM)
 928                         adapter->if_events.TpCsum++;
 929                 if (hdr->frame_status_b14 & VRHSTATB_TPHLEN)
 930                         adapter->if_events.TpHlen++;
 931                 if (hdr->frame_status_b14 & VRHSTATB_IPCSUM)
 932                         adapter->if_events.IpCsum++;
 933                 if (hdr->frame_status_b14 & VRHSTATB_IPLERR)
 934                         adapter->if_events.IpLen++;
 935                 if (hdr->frame_status_b14 & VRHSTATB_IPHERR)
 936                         adapter->if_events.IpHlen++;
 937         } else {
 938                 if (hdr->frame_statusGB & VGBSTAT_XPERR) {
 939                         u32 xerr = hdr->frame_statusGB >> VGBSTAT_XERRSHFT;
 940
 941                         if (xerr == VGBSTAT_XCSERR)
 942                                 adapter->if_events.TpCsum++;
 943                         if (xerr == VGBSTAT_XUFLOW)
 944                                 adapter->if_events.Tprtoflow++;
 945                         if (xerr == VGBSTAT_XHLEN)
 946                                 adapter->if_events.TpHlen++;
 947                 }
 948                 if (hdr->frame_statusGB & VGBSTAT_NETERR) {
 949                         u32 nerr =
 950                             (hdr->
 951                              frame_statusGB >> VGBSTAT_NERRSHFT) &
 952                             VGBSTAT_NERRMSK;
 953                         if (nerr == VGBSTAT_NCSERR)
 954                                 adapter->if_events.IpCsum++;
 955                         if (nerr == VGBSTAT_NUFLOW)
 956                                 adapter->if_events.IpLen++;
 957                         if (nerr == VGBSTAT_NHLEN)
 958                                 adapter->if_events.IpHlen++;
 959                 }
 960                 if (hdr->frame_statusGB & VGBSTAT_LNKERR) {
 961                         u32 lerr = hdr->frame_statusGB & VGBSTAT_LERRMSK;
 962
 963                         if (lerr == VGBSTAT_LDEARLY)
 964                                 adapter->if_events.rcvearly++;
 965                         if (lerr == VGBSTAT_LBOFLO)
 966                                 adapter->if_events.Bufov++;
 967                         if (lerr == VGBSTAT_LCODERR)
 968                                 adapter->if_events.Code++;
 969                         if (lerr == VGBSTAT_LDBLNBL)
 970                                 adapter->if_events.Drbl++;
 971                         if (lerr == VGBSTAT_LCRCERR)
 972                                 adapter->if_events.Crc++;
 973                         if (lerr == VGBSTAT_LOFLO)
 974                                 adapter->if_events.oflow802++;
 975                         if (lerr == VGBSTAT_LUFLO)
 976                                 adapter->if_events.uflow802++;
 977                 }
 978         }
 979         return;
 980 }
 981
 982 #define TCP_OFFLOAD_FRAME_PUSHFLAG  0x10000000
 983 #define M_FAST_PATH                 0x0040
 984
 985 static void slic_rcv_handler(struct adapter *adapter)
 986 {
 987         struct sk_buff *skb;
 988         struct slic_rcvbuf *rcvbuf;
 989         u32 frames = 0;
 990
 991         while ((skb = slic_rcvqueue_getnext(adapter))) {
 992                 u32 rx_bytes;
 993
 994                 ASSERT(skb->head);
 995                 rcvbuf = (struct slic_rcvbuf *)skb->head;
 996                 adapter->card->events++;
 997                 if (rcvbuf->status & IRHDDR_ERR) {
 998                         adapter->rx_errors++;
 999                         slic_rcv_handle_error(adapter, rcvbuf);
1000                         slic_rcvqueue_reinsert(adapter, skb);
1001                         continue;
1002                 }
1003
1004                 if (!slic_mac_filter(adapter, (struct ether_header *)
1005                                         rcvbuf->data)) {
1006                         slic_rcvqueue_reinsert(adapter, skb);
1007                         continue;
1008                 }
1009                 skb_pull(skb, SLIC_RCVBUF_HEADSIZE);
1010                 rx_bytes = (rcvbuf->length & IRHDDR_FLEN_MSK);
1011                 skb_put(skb, rx_bytes);
1012                 adapter->stats.rx_packets++;
1013                 adapter->stats.rx_bytes += rx_bytes;
1014 #if SLIC_OFFLOAD_IP_CHECKSUM
1015                 skb->ip_summed = CHECKSUM_UNNECESSARY;
1016 #endif
1017
1018                 skb->dev = adapter->netdev;
1019                 skb->protocol = eth_type_trans(skb, skb->dev);
1020                 netif_rx(skb);
1021
1022                 ++frames;
1023 #if SLIC_INTERRUPT_PROCESS_LIMIT
1024                 if (frames >= SLIC_RCVQ_MAX_PROCESS_ISR) {
1025                         adapter->rcv_interrupt_yields++;
1026                         break;
1027                 }
1028 #endif
1029         }
1030         adapter->max_isr_rcvs = max(adapter->max_isr_rcvs, frames);
1031 }
1032
1033 static void slic_xmit_complete(struct adapter *adapter)
1034 {
1035         struct slic_hostcmd *hcmd;
1036         struct slic_rspbuf *rspbuf;
1037         u32 frames = 0;
1038         struct slic_handle_word slic_handle_word;
1039
1040         do {
1041                 rspbuf = slic_rspqueue_getnext(adapter);
1042                 if (!rspbuf)
1043                         break;
1044                 adapter->xmit_completes++;
1045                 adapter->card->events++;
1046                 /*
1047                  Get the complete host command buffer
1048                 */
1049                 slic_handle_word.handle_token = rspbuf->hosthandle;
1050                 ASSERT(slic_handle_word.handle_index);
1051                 ASSERT(slic_handle_word.handle_index <= SLIC_CMDQ_MAXCMDS);
1052                 hcmd =
1053                     (struct slic_hostcmd *)
1054                         adapter->slic_handles[slic_handle_word.handle_index].
1055                                                                         address;
1056 /*      hcmd = (struct slic_hostcmd *) rspbuf->hosthandle; */
1057                 ASSERT(hcmd);
1058                 ASSERT(hcmd->pslic_handle ==
1059                        &adapter->slic_handles[slic_handle_word.handle_index]);
1060                 if (hcmd->type == SLIC_CMD_DUMB) {
1061                         if (hcmd->skb)
1062                                 dev_kfree_skb_irq(hcmd->skb);
1063                         slic_cmdq_putdone_irq(adapter, hcmd);
1064                 }
1065                 rspbuf->status = 0;
1066                 rspbuf->hosthandle = 0;
1067                 frames++;
1068         } while (1);
1069         adapter->max_isr_xmits = max(adapter->max_isr_xmits, frames);
1070 }
1071
1072 static irqreturn_t slic_interrupt(int irq, void *dev_id)
1073 {
1074         struct net_device *dev = (struct net_device *)dev_id;
1075         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
1076         u32 isr;
1077
1078         if ((adapter->pshmem) && (adapter->pshmem->isr)) {
1079                 slic_reg32_write(&adapter->slic_regs->slic_icr,
1080                                  ICR_INT_MASK, FLUSH);
1081                 isr = adapter->isrcopy = adapter->pshmem->isr;
1082                 adapter->pshmem->isr = 0;
1083                 adapter->num_isrs++;
1084                 switch (adapter->card->state) {
1085                 case CARD_UP:
1086                         if (isr & ~ISR_IO) {
1087                                 if (isr & ISR_ERR) {
1088                                         adapter->error_interrupts++;
1089                                         if (isr & ISR_RMISS) {
1090                                                 int count;
1091                                                 int pre_count;
1092                                                 int errors;
1093
1094                                                 struct slic_rcvqueue *rcvq =
1095                                                     &adapter->rcvqueue;
1096
1097                                                 adapter->
1098                                                     error_rmiss_interrupts++;
1099                                                 if (!rcvq->errors)
1100                                                         rcv_count = rcvq->count;
1101                                                 pre_count = rcvq->count;
1102                                                 errors = rcvq->errors;
1103
1104                                                 while (rcvq->count <
1105                                                        SLIC_RCVQ_FILLTHRESH) {
1106                                                         count =
1107                                                             slic_rcvqueue_fill
1108                                                             (adapter);
1109                                                         if (!count)
1110                                                                 break;
1111                                                 }
1112                                         } else if (isr & ISR_XDROP) {
1113                                                 dev_err(&dev->dev,
1114                                                         "isr & ISR_ERR [%x] "
1115                                                         "ISR_XDROP \n", isr);
1116                                         } else {
1117                                                 dev_err(&dev->dev,
1118                                                         "isr & ISR_ERR [%x]\n",
1119                                                         isr);
1120                                         }
1121                                 }
1122
1123                                 if (isr & ISR_LEVENT) {
1124                                         adapter->linkevent_interrupts++;
1125                                         slic_link_event_handler(adapter);
1126                                 }
1127
1128                                 if ((isr & ISR_UPC) ||
1129                                     (isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) {
1130                                         adapter->upr_interrupts++;
1131                                         slic_upr_request_complete(adapter, isr);
1132                                 }
1133                         }
1134
1135                         if (isr & ISR_RCV) {
1136                                 adapter->rcv_interrupts++;
1137                                 slic_rcv_handler(adapter);
1138                         }
1139
1140                         if (isr & ISR_CMD) {
1141                                 adapter->xmit_interrupts++;
1142                                 slic_xmit_complete(adapter);
1143                         }
1144                         break;
1145
1146                 case CARD_DOWN:
1147                         if ((isr & ISR_UPC) ||
1148                             (isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) {
1149                                 adapter->upr_interrupts++;
1150                                 slic_upr_request_complete(adapter, isr);
1151                         }
1152                         break;
1153
1154                 default:
1155                         break;
1156                 }
1157
1158                 adapter->isrcopy = 0;
1159                 adapter->all_reg_writes += 2;
1160                 adapter->isr_reg_writes++;
1161                 slic_reg32_write(&adapter->slic_regs->slic_isr, 0, FLUSH);
1162         } else {
1163                 adapter->false_interrupts++;
1164         }
1165         return IRQ_HANDLED;
1166 }
1167
1168 /*
1169  * slic_link_event_handler -
1170  *
1171  * Initiate a link configuration sequence.  The link configuration begins
1172  * by issuing a READ_LINK_STATUS command to the Utility Processor on the
1173  * SLIC.  Since the command finishes asynchronously, the slic_upr_comlete
1174  * routine will follow it up witha UP configuration write command, which
1175  * will also complete asynchronously.
1176  *
1177  */
1178 static void slic_link_event_handler(struct adapter *adapter)
1179 {
1180         int status;
1181         struct slic_shmem *pshmem;
1182
1183         if (adapter->state != ADAPT_UP) {
1184                 /* Adapter is not operational.  Ignore.  */
1185                 return;
1186         }
1187
1188         pshmem = (struct slic_shmem *)adapter->phys_shmem;
1189
1190 #if defined(CONFIG_X86_64)
1191         status = slic_upr_request(adapter,
1192                                   SLIC_UPR_RLSR,
1193                                   SLIC_GET_ADDR_LOW(&pshmem->linkstatus),
1194                                   SLIC_GET_ADDR_HIGH(&pshmem->linkstatus),
1195                                   0, 0);
1196 #elif defined(CONFIG_X86)
1197         status = slic_upr_request(adapter, SLIC_UPR_RLSR,
1198                 (u32) &pshmem->linkstatus,      /* no 4GB wrap guaranteed */
1199                                   0, 0, 0);
1200 #else
1201         Stop compilation;
1202 #endif
1203         ASSERT((status == STATUS_SUCCESS) || (status == STATUS_PENDING));
1204 }
1205
1206 static void slic_init_cleanup(struct adapter *adapter)
1207 {
1208         if (adapter->intrregistered) {
1209                 adapter->intrregistered = 0;
1210                 free_irq(adapter->netdev->irq, adapter->netdev);
1211
1212         }
1213         if (adapter->pshmem) {
1214                 pci_free_consistent(adapter->pcidev,
1215                                     sizeof(struct slic_shmem),
1216                                     adapter->pshmem, adapter->phys_shmem);
1217                 adapter->pshmem = NULL;
1218                 adapter->phys_shmem = (dma_addr_t) NULL;
1219         }
1220
1221         if (adapter->pingtimerset) {
1222                 adapter->pingtimerset = 0;
1223                 del_timer(&adapter->pingtimer);
1224         }
1225
1226         slic_rspqueue_free(adapter);
1227         slic_cmdq_free(adapter);
1228         slic_rcvqueue_free(adapter);
1229 }
1230
1231 static struct net_device_stats *slic_get_stats(struct net_device *dev)
1232 {
1233         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
1234         struct net_device_stats *stats;
1235
1236         ASSERT(adapter);
1237         stats = &adapter->stats;
1238         stats->collisions = adapter->slic_stats.iface.xmit_collisions;
1239         stats->rx_errors = adapter->slic_stats.iface.rcv_errors;
1240         stats->tx_errors = adapter->slic_stats.iface.xmt_errors;
1241         stats->rx_missed_errors = adapter->slic_stats.iface.rcv_discards;
1242         stats->tx_heartbeat_errors = 0;
1243         stats->tx_aborted_errors = 0;
1244         stats->tx_window_errors = 0;
1245         stats->tx_fifo_errors = 0;
1246         stats->rx_frame_errors = 0;
1247         stats->rx_length_errors = 0;
1248         return &adapter->stats;
1249 }
1250
1251 /*
1252  *  Allocate a mcast_address structure to hold the multicast address.
1253  *  Link it in.
1254  */
1255 static int slic_mcast_add_list(struct adapter *adapter, char *address)
1256 {
1257         struct mcast_address *mcaddr, *mlist;
1258         bool equaladdr;
1259
1260         /* Check to see if it already exists */
1261         mlist = adapter->mcastaddrs;
1262         while (mlist) {
1263                 ETHER_EQ_ADDR(mlist->address, address, equaladdr);
1264                 if (equaladdr)
1265                         return STATUS_SUCCESS;
1266                 mlist = mlist->next;
1267         }
1268
1269         /* Doesn't already exist.  Allocate a structure to hold it */
1270         mcaddr = kmalloc(sizeof(struct mcast_address), GFP_ATOMIC);
1271         if (mcaddr == NULL)
1272                 return 1;
1273
1274         memcpy(mcaddr->address, address, 6);
1275
1276         mcaddr->next = adapter->mcastaddrs;
1277         adapter->mcastaddrs = mcaddr;
1278
1279         return STATUS_SUCCESS;
1280 }
1281
1282 /*
1283  * Functions to obtain the CRC corresponding to the destination mac address.
1284  * This is a standard ethernet CRC in that it is a 32-bit, reflected CRC using
1285  * the polynomial:
1286  *   x^32 + x^26 + x^23 + x^22 + x^16 + x^12 + x^11 + x^10 + x^8 + x^7 + x^5 +
1287  *   x^4 + x^2 + x^1.
1288  *
1289  * After the CRC for the 6 bytes is generated (but before the value is
1290  * complemented),
1291  * we must then transpose the value and return bits 30-23.
1292  *
1293  */
1294 static u32 slic_crc_table[256]; /* Table of CRCs for all possible byte values */
1295 static u32 slic_crc_init;       /* Is table initialized */
1296
1297 /*
1298  *  Contruct the CRC32 table
1299  */
1300 static void slic_mcast_init_crc32(void)
1301 {
1302         u32 c;          /*  CRC shit reg                 */
1303         u32 e = 0;              /*  Poly X-or pattern            */
1304         int i;                  /*  counter                      */
1305         int k;                  /*  byte being shifted into crc  */
1306
1307         static int p[] = { 0, 1, 2, 4, 5, 7, 8, 10, 11, 12, 16, 22, 23, 26 };
1308
1309         for (i = 0; i < sizeof(p) / sizeof(int); i++)
1310                 e |= 1L << (31 - p[i]);
1311
1312         for (i = 1; i < 256; i++) {
1313                 c = i;
1314                 for (k = 8; k; k--)
1315                         c = c & 1 ? (c >> 1) ^ e : c >> 1;
1316                 slic_crc_table[i] = c;
1317         }
1318 }
1319
1320 /*
1321  *  Return the MAC hast as described above.
1322  */
1323 static unsigned char slic_mcast_get_mac_hash(char *macaddr)
1324 {
1325         u32 crc;
1326         char *p;
1327         int i;
1328         unsigned char machash = 0;
1329
1330         if (!slic_crc_init) {
1331                 slic_mcast_init_crc32();
1332                 slic_crc_init = 1;
1333         }
1334
1335         crc = 0xFFFFFFFF;       /* Preload shift register, per crc-32 spec */
1336         for (i = 0, p = macaddr; i < 6; ++p, ++i)
1337                 crc = (crc >> 8) ^ slic_crc_table[(crc ^ *p) & 0xFF];
1338
1339         /* Return bits 1-8, transposed */
1340         for (i = 1; i < 9; i++)
1341                 machash |= (((crc >> i) & 1) << (8 - i));
1342
1343         return machash;
1344 }
1345
1346 static void slic_mcast_set_bit(struct adapter *adapter, char *address)
1347 {
1348         unsigned char crcpoly;
1349
1350         /* Get the CRC polynomial for the mac address */
1351         crcpoly = slic_mcast_get_mac_hash(address);
1352
1353         /* We only have space on the SLIC for 64 entries.  Lop
1354          * off the top two bits. (2^6 = 64)
1355          */
1356         crcpoly &= 0x3F;
1357
1358         /* OR in the new bit into our 64 bit mask. */
1359         adapter->mcastmask |= (u64) 1 << crcpoly;
1360 }
1361
1362 static void slic_mcast_set_list(struct net_device *dev)
1363 {
1364         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
1365         int status = STATUS_SUCCESS;
1366         int i;
1367         char *addresses;
1368         struct dev_mc_list *mc_list = dev->mc_list;
1369         int mc_count = dev->mc_count;
1370
1371         ASSERT(adapter);
1372
1373         for (i = 1; i <= mc_count; i++) {
1374                 addresses = (char *) &mc_list->dmi_addr;
1375                 if (mc_list->dmi_addrlen == 6) {
1376                         status = slic_mcast_add_list(adapter, addresses);
1377                         if (status != STATUS_SUCCESS)
1378                                 break;
1379                 } else {
1380                         status = -EINVAL;
1381                         break;
1382                 }
1383                 slic_mcast_set_bit(adapter, addresses);
1384                 mc_list = mc_list->next;
1385         }
1386
1387         if (adapter->devflags_prev != dev->flags) {
1388                 adapter->macopts = MAC_DIRECTED;
1389                 if (dev->flags) {
1390                         if (dev->flags & IFF_BROADCAST)
1391                                 adapter->macopts |= MAC_BCAST;
1392                         if (dev->flags & IFF_PROMISC)
1393                                 adapter->macopts |= MAC_PROMISC;
1394                         if (dev->flags & IFF_ALLMULTI)
1395                                 adapter->macopts |= MAC_ALLMCAST;
1396                         if (dev->flags & IFF_MULTICAST)
1397                                 adapter->macopts |= MAC_MCAST;
1398                 }
1399                 adapter->devflags_prev = dev->flags;
1400                 slic_config_set(adapter, true);
1401         } else {
1402                 if (status == STATUS_SUCCESS)
1403                         slic_mcast_set_mask(adapter);
1404         }
1405         return;
1406 }
1407
1408 static void slic_mcast_set_mask(struct adapter *adapter)
1409 {
1410         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1411
1412         if (adapter->macopts & (MAC_ALLMCAST | MAC_PROMISC)) {
1413                 /* Turn on all multicast addresses. We have to do this for
1414                  * promiscuous mode as well as ALLMCAST mode.  It saves the
1415                  * Microcode from having to keep state about the MAC
1416                  * configuration.
1417                  */
1418                 slic_reg32_write(&slic_regs->slic_mcastlow, 0xFFFFFFFF, FLUSH);
1419                 slic_reg32_write(&slic_regs->slic_mcasthigh, 0xFFFFFFFF,
1420                                  FLUSH);
1421         } else {
1422                 /* Commit our multicast mast to the SLIC by writing to the
1423                  * multicast address mask registers
1424                  */
1425                 slic_reg32_write(&slic_regs->slic_mcastlow,
1426                         (u32)(adapter->mcastmask & 0xFFFFFFFF), FLUSH);
1427                 slic_reg32_write(&slic_regs->slic_mcasthigh,
1428                         (u32)((adapter->mcastmask >> 32) & 0xFFFFFFFF), FLUSH);
1429         }
1430 }
1431
1432 static void slic_timer_ping(ulong dev)
1433 {
1434         struct adapter *adapter;
1435         struct sliccard *card;
1436
1437         ASSERT(dev);
1438         adapter = netdev_priv((struct net_device *)dev);
1439         ASSERT(adapter);
1440         card = adapter->card;
1441         ASSERT(card);
1442
1443         adapter->pingtimer.expires = jiffies + (PING_TIMER_INTERVAL * HZ);
1444         add_timer(&adapter->pingtimer);
1445 }
1446
1447 /*
1448  *  slic_if_init
1449  *
1450  *  Perform initialization of our slic interface.
1451  *
1452  */
1453 static int slic_if_init(struct adapter *adapter)
1454 {
1455         struct sliccard *card = adapter->card;
1456         struct net_device *dev = adapter->netdev;
1457         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1458         struct slic_shmem *pshmem;
1459         int status = 0;
1460
1461         ASSERT(card);
1462
1463         /* adapter should be down at this point */
1464         if (adapter->state != ADAPT_DOWN) {
1465                 dev_err(&dev->dev, "%s: adapter->state != ADAPT_DOWN\n",
1466                         __func__);
1467                 return -EIO;
1468         }
1469         ASSERT(adapter->linkstate == LINK_DOWN);
1470
1471         adapter->devflags_prev = dev->flags;
1472         adapter->macopts = MAC_DIRECTED;
1473         if (dev->flags) {
1474                 if (dev->flags & IFF_BROADCAST)
1475                         adapter->macopts |= MAC_BCAST;
1476                 if (dev->flags & IFF_PROMISC)
1477                         adapter->macopts |= MAC_PROMISC;
1478                 if (dev->flags & IFF_ALLMULTI)
1479                         adapter->macopts |= MAC_ALLMCAST;
1480                 if (dev->flags & IFF_MULTICAST)
1481                         adapter->macopts |= MAC_MCAST;
1482         }
1483         status = slic_adapter_allocresources(adapter);
1484         if (status != STATUS_SUCCESS) {
1485                 dev_err(&dev->dev,
1486                         "%s: slic_adapter_allocresources FAILED %x\n",
1487                         __func__, status);
1488                 slic_adapter_freeresources(adapter);
1489                 return status;
1490         }
1491
1492         if (!adapter->queues_initialized) {
1493                 if (slic_rspqueue_init(adapter))
1494                         return -ENOMEM;
1495                 if (slic_cmdq_init(adapter))
1496                         return -ENOMEM;
1497                 if (slic_rcvqueue_init(adapter))
1498                         return -ENOMEM;
1499                 adapter->queues_initialized = 1;
1500         }
1501
1502         slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH);
1503         mdelay(1);
1504
1505         if (!adapter->isp_initialized) {
1506                 pshmem = (struct slic_shmem *)adapter->phys_shmem;
1507
1508                 spin_lock_irqsave(&adapter->bit64reglock.lock,
1509                                         adapter->bit64reglock.flags);
1510
1511 #if defined(CONFIG_X86_64)
1512                 slic_reg32_write(&slic_regs->slic_addr_upper,
1513                                  SLIC_GET_ADDR_HIGH(&pshmem->isr), DONT_FLUSH);
1514                 slic_reg32_write(&slic_regs->slic_isp,
1515                                  SLIC_GET_ADDR_LOW(&pshmem->isr), FLUSH);
1516 #elif defined(CONFIG_X86)
1517                 slic_reg32_write(&slic_regs->slic_addr_upper, 0, DONT_FLUSH);
1518                 slic_reg32_write(&slic_regs->slic_isp, (u32)&pshmem->isr, FLUSH);
1519 #else
1520                 Stop Compilations
1521 #endif
1522                 spin_unlock_irqrestore(&adapter->bit64reglock.lock,
1523                                         adapter->bit64reglock.flags);
1524                 adapter->isp_initialized = 1;
1525         }
1526
1527         adapter->state = ADAPT_UP;
1528         if (!card->loadtimerset) {
1529                 init_timer(&card->loadtimer);
1530                 card->loadtimer.expires =
1531                     jiffies + (SLIC_LOADTIMER_PERIOD * HZ);
1532                 card->loadtimer.data = (ulong) card;
1533                 card->loadtimer.function = &slic_timer_load_check;
1534                 add_timer(&card->loadtimer);
1535
1536                 card->loadtimerset = 1;
1537         }
1538
1539         if (!adapter->pingtimerset) {
1540                 init_timer(&adapter->pingtimer);
1541                 adapter->pingtimer.expires =
1542                     jiffies + (PING_TIMER_INTERVAL * HZ);
1543                 adapter->pingtimer.data = (ulong) dev;
1544                 adapter->pingtimer.function = &slic_timer_ping;
1545                 add_timer(&adapter->pingtimer);
1546                 adapter->pingtimerset = 1;
1547                 adapter->card->pingstatus = ISR_PINGMASK;
1548         }
1549
1550         /*
1551          *    clear any pending events, then enable interrupts
1552          */
1553         adapter->isrcopy = 0;
1554         adapter->pshmem->isr = 0;
1555         slic_reg32_write(&slic_regs->slic_isr, 0, FLUSH);
1556         slic_reg32_write(&slic_regs->slic_icr, ICR_INT_ON, FLUSH);
1557
1558         slic_link_config(adapter, LINK_AUTOSPEED, LINK_AUTOD);
1559         slic_link_event_handler(adapter);
1560
1561         return STATUS_SUCCESS;
1562 }
1563
1564 static void slic_unmap_mmio_space(struct adapter *adapter)
1565 {
1566         if (adapter->slic_regs)
1567                 iounmap(adapter->slic_regs);
1568         adapter->slic_regs = NULL;
1569 }
1570
1571 static int slic_adapter_allocresources(struct adapter *adapter)
1572 {
1573         if (!adapter->intrregistered) {
1574                 int retval;
1575
1576                 spin_unlock_irqrestore(&slic_global.driver_lock.lock,
1577                                         slic_global.driver_lock.flags);
1578
1579                 retval = request_irq(adapter->netdev->irq,
1580                                      &slic_interrupt,
1581                                      IRQF_SHARED,
1582                                      adapter->netdev->name, adapter->netdev);
1583
1584                 spin_lock_irqsave(&slic_global.driver_lock.lock,
1585                                         slic_global.driver_lock.flags);
1586
1587                 if (retval) {
1588                         dev_err(&adapter->netdev->dev,
1589                                 "request_irq (%s) FAILED [%x]\n",
1590                                 adapter->netdev->name, retval);
1591                         return retval;
1592                 }
1593                 adapter->intrregistered = 1;
1594         }
1595         return STATUS_SUCCESS;
1596 }
1597
1598 static void slic_config_pci(struct pci_dev *pcidev)
1599 {
1600         u16 pci_command;
1601         u16 new_command;
1602
1603         pci_read_config_word(pcidev, PCI_COMMAND, &pci_command);
1604
1605         new_command = pci_command | PCI_COMMAND_MASTER
1606             | PCI_COMMAND_MEMORY
1607             | PCI_COMMAND_INVALIDATE
1608             | PCI_COMMAND_PARITY | PCI_COMMAND_SERR | PCI_COMMAND_FAST_BACK;
1609         if (pci_command != new_command)
1610                 pci_write_config_word(pcidev, PCI_COMMAND, new_command);
1611 }
1612
1613 static void slic_adapter_freeresources(struct adapter *adapter)
1614 {
1615         slic_init_cleanup(adapter);
1616         memset(&adapter->stats, 0, sizeof(struct net_device_stats));
1617         adapter->error_interrupts = 0;
1618         adapter->rcv_interrupts = 0;
1619         adapter->xmit_interrupts = 0;
1620         adapter->linkevent_interrupts = 0;
1621         adapter->upr_interrupts = 0;
1622         adapter->num_isrs = 0;
1623         adapter->xmit_completes = 0;
1624         adapter->rcv_broadcasts = 0;
1625         adapter->rcv_multicasts = 0;
1626         adapter->rcv_unicasts = 0;
1627 }
1628
1629 /*
1630  *  slic_link_config
1631  *
1632  *  Write phy control to configure link duplex/speed
1633  *
1634  */
1635 static void slic_link_config(struct adapter *adapter,
1636                       u32 linkspeed, u32 linkduplex)
1637 {
1638         u32 __iomem *wphy;
1639         u32 speed;
1640         u32 duplex;
1641         u32 phy_config;
1642         u32 phy_advreg;
1643         u32 phy_gctlreg;
1644
1645         if (adapter->state != ADAPT_UP)
1646                 return;
1647
1648         ASSERT((adapter->devid == SLIC_1GB_DEVICE_ID)
1649                || (adapter->devid == SLIC_2GB_DEVICE_ID));
1650
1651         if (linkspeed > LINK_1000MB)
1652                 linkspeed = LINK_AUTOSPEED;
1653         if (linkduplex > LINK_AUTOD)
1654                 linkduplex = LINK_AUTOD;
1655
1656         wphy = &adapter->slic_regs->slic_wphy;
1657
1658         if ((linkspeed == LINK_AUTOSPEED) || (linkspeed == LINK_1000MB)) {
1659                 if (adapter->flags & ADAPT_FLAGS_FIBERMEDIA) {
1660                         /*  We've got a fiber gigabit interface, and register
1661                          *  4 is different in fiber mode than in copper mode
1662                          */
1663
1664                         /* advertise FD only @1000 Mb */
1665                         phy_advreg = (MIICR_REG_4 | (PAR_ADV1000XFD));
1666                         /* enable PAUSE frames        */
1667                         phy_advreg |= PAR_ASYMPAUSE_FIBER;
1668                         slic_reg32_write(wphy, phy_advreg, FLUSH);
1669
1670                         if (linkspeed == LINK_AUTOSPEED) {
1671                                 /* reset phy, enable auto-neg  */
1672                                 phy_config =
1673                                     (MIICR_REG_PCR |
1674                                      (PCR_RESET | PCR_AUTONEG |
1675                                       PCR_AUTONEG_RST));
1676                                 slic_reg32_write(wphy, phy_config, FLUSH);
1677                         } else {        /* forced 1000 Mb FD*/
1678                                 /* power down phy to break link
1679                                    this may not work) */
1680                                 phy_config = (MIICR_REG_PCR | PCR_POWERDOWN);
1681                                 slic_reg32_write(wphy, phy_config, FLUSH);
1682                                 /* wait, Marvell says 1 sec,
1683                                    try to get away with 10 ms  */
1684                                 mdelay(10);
1685
1686                                 /* disable auto-neg, set speed/duplex,
1687                                    soft reset phy, powerup */
1688                                 phy_config =
1689                                     (MIICR_REG_PCR |
1690                                      (PCR_RESET | PCR_SPEED_1000 |
1691                                       PCR_DUPLEX_FULL));
1692                                 slic_reg32_write(wphy, phy_config, FLUSH);
1693                         }
1694                 } else {        /* copper gigabit */
1695
1696                         /* Auto-Negotiate or 1000 Mb must be auto negotiated
1697                          * We've got a copper gigabit interface, and
1698                          * register 4 is different in copper mode than
1699                          * in fiber mode
1700                          */
1701                         if (linkspeed == LINK_AUTOSPEED) {
1702                                 /* advertise 10/100 Mb modes   */
1703                                 phy_advreg =
1704                                     (MIICR_REG_4 |
1705                                      (PAR_ADV100FD | PAR_ADV100HD | PAR_ADV10FD
1706                                       | PAR_ADV10HD));
1707                         } else {
1708                         /* linkspeed == LINK_1000MB -
1709                            don't advertise 10/100 Mb modes  */
1710                                 phy_advreg = MIICR_REG_4;
1711                         }
1712                         /* enable PAUSE frames  */
1713                         phy_advreg |= PAR_ASYMPAUSE;
1714                         /* required by the Cicada PHY  */
1715                         phy_advreg |= PAR_802_3;
1716                         slic_reg32_write(wphy, phy_advreg, FLUSH);
1717                         /* advertise FD only @1000 Mb  */
1718                         phy_gctlreg = (MIICR_REG_9 | (PGC_ADV1000FD));
1719                         slic_reg32_write(wphy, phy_gctlreg, FLUSH);
1720
1721                         if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) {
1722                                 /* if a Marvell PHY
1723                                    enable auto crossover */
1724                                 phy_config =
1725                                     (MIICR_REG_16 | (MRV_REG16_XOVERON));
1726                                 slic_reg32_write(wphy, phy_config, FLUSH);
1727
1728                                 /* reset phy, enable auto-neg  */
1729                                 phy_config =
1730                                     (MIICR_REG_PCR |
1731                                      (PCR_RESET | PCR_AUTONEG |
1732                                       PCR_AUTONEG_RST));
1733                                 slic_reg32_write(wphy, phy_config, FLUSH);
1734                         } else {        /* it's a Cicada PHY  */
1735                                 /* enable and restart auto-neg (don't reset)  */
1736                                 phy_config =
1737                                     (MIICR_REG_PCR |
1738                                      (PCR_AUTONEG | PCR_AUTONEG_RST));
1739                                 slic_reg32_write(wphy, phy_config, FLUSH);
1740                         }
1741                 }
1742         } else {
1743                 /* Forced 10/100  */
1744                 if (linkspeed == LINK_10MB)
1745                         speed = 0;
1746                 else
1747                         speed = PCR_SPEED_100;
1748                 if (linkduplex == LINK_HALFD)
1749                         duplex = 0;
1750                 else
1751                         duplex = PCR_DUPLEX_FULL;
1752
1753                 if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) {
1754                         /* if a Marvell PHY
1755                            disable auto crossover  */
1756                         phy_config = (MIICR_REG_16 | (MRV_REG16_XOVEROFF));
1757                         slic_reg32_write(wphy, phy_config, FLUSH);
1758                 }
1759
1760                 /* power down phy to break link (this may not work)  */
1761                 phy_config = (MIICR_REG_PCR | (PCR_POWERDOWN | speed | duplex));
1762                 slic_reg32_write(wphy, phy_config, FLUSH);
1763
1764                 /* wait, Marvell says 1 sec, try to get away with 10 ms */
1765                 mdelay(10);
1766
1767                 if (adapter->subsysid != SLIC_1GB_CICADA_SUBSYS_ID) {
1768                         /* if a Marvell PHY
1769                            disable auto-neg, set speed,
1770                            soft reset phy, powerup */
1771                         phy_config =
1772                             (MIICR_REG_PCR | (PCR_RESET | speed | duplex));
1773                         slic_reg32_write(wphy, phy_config, FLUSH);
1774                 } else {        /* it's a Cicada PHY  */
1775                         /* disable auto-neg, set speed, powerup  */
1776                         phy_config = (MIICR_REG_PCR | (speed | duplex));
1777                         slic_reg32_write(wphy, phy_config, FLUSH);
1778                 }
1779         }
1780 }
1781
1782 static void slic_card_cleanup(struct sliccard *card)
1783 {
1784         if (card->loadtimerset) {
1785                 card->loadtimerset = 0;
1786                 del_timer(&card->loadtimer);
1787         }
1788
1789         slic_debug_card_destroy(card);
1790
1791         kfree(card);
1792 }
1793
1794 static int slic_card_download_gbrcv(struct adapter *adapter)
1795 {
1796         const struct firmware *fw;
1797         const char *file = "";
1798         int ret;
1799         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1800         u32 codeaddr;
1801         u32 instruction;
1802         int index = 0;
1803         u32 rcvucodelen = 0;
1804
1805         switch (adapter->devid) {
1806         case SLIC_2GB_DEVICE_ID:
1807                 file = "slicoss/oasisrcvucode.sys";
1808                 break;
1809         case SLIC_1GB_DEVICE_ID:
1810                 file = "slicoss/gbrcvucode.sys";
1811                 break;
1812         default:
1813                 ASSERT(0);
1814                 break;
1815         }
1816
1817         ret = request_firmware(&fw, file, &adapter->pcidev->dev);
1818         if (ret) {
1819                 dev_err(&adapter->pcidev->dev,
1820                         "SLICOSS: Failed to load firmware %s\n", file);
1821                 return ret;
1822         }
1823
1824         rcvucodelen = *(u32 *)(fw->data + index);
1825         index += 4;
1826         switch (adapter->devid) {
1827         case SLIC_2GB_DEVICE_ID:
1828                 if (rcvucodelen != OasisRcvUCodeLen)
1829                         return -EINVAL;
1830                 break;
1831         case SLIC_1GB_DEVICE_ID:
1832                 if (rcvucodelen != GBRcvUCodeLen)
1833                         return -EINVAL;
1834                 break;
1835         default:
1836                 ASSERT(0);
1837                 break;
1838         }
1839         /* start download */
1840         slic_reg32_write(&slic_regs->slic_rcv_wcs, SLIC_RCVWCS_BEGIN, FLUSH);
1841         /* download the rcv sequencer ucode */
1842         for (codeaddr = 0; codeaddr < rcvucodelen; codeaddr++) {
1843                 /* write out instruction address */
1844                 slic_reg32_write(&slic_regs->slic_rcv_wcs, codeaddr, FLUSH);
1845
1846                 instruction = *(u32 *)(fw->data + index);
1847                 index += 4;
1848                 /* write out the instruction data low addr */
1849                 slic_reg32_write(&slic_regs->slic_rcv_wcs, instruction, FLUSH);
1850
1851                 instruction = *(u8 *)(fw->data + index);
1852                 index++;
1853                 /* write out the instruction data high addr */
1854                 slic_reg32_write(&slic_regs->slic_rcv_wcs, (u8)instruction,
1855                                  FLUSH);
1856         }
1857
1858         /* download finished */
1859         release_firmware(fw);
1860         slic_reg32_write(&slic_regs->slic_rcv_wcs, SLIC_RCVWCS_FINISH, FLUSH);
1861         return 0;
1862 }
1863
1864 static int slic_card_download(struct adapter *adapter)
1865 {
1866         const struct firmware *fw;
1867         const char *file = "";
1868         int ret;
1869         u32 section;
1870         int thissectionsize;
1871         int codeaddr;
1872         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
1873         u32 instruction;
1874         u32 baseaddress;
1875         u32 i;
1876         u32 numsects = 0;
1877         u32 sectsize[3];
1878         u32 sectstart[3];
1879         int ucode_start, index = 0;
1880
1881         switch (adapter->devid) {
1882         case SLIC_2GB_DEVICE_ID:
1883                 file = "slicoss/oasisdownload.sys";
1884                 break;
1885         case SLIC_1GB_DEVICE_ID:
1886                 file = "slicoss/gbdownload.sys";
1887                 break;
1888         default:
1889                 ASSERT(0);
1890                 break;
1891         }
1892         ret = request_firmware(&fw, file, &adapter->pcidev->dev);
1893         if (ret) {
1894                 dev_err(&adapter->pcidev->dev,
1895                         "SLICOSS: Failed to load firmware %s\n", file);
1896                 return ret;
1897         }
1898         numsects = *(u32 *)(fw->data + index);
1899         index += 4;
1900         ASSERT(numsects <= 3);
1901         for (i = 0; i < numsects; i++) {
1902                 sectsize[i] = *(u32 *)(fw->data + index);
1903                 index += 4;
1904         }
1905         for (i = 0; i < numsects; i++) {
1906                 sectstart[i] = *(u32 *)(fw->data + index);
1907                 index += 4;
1908         }
1909         ucode_start = index;
1910         instruction = *(u32 *)(fw->data + index);
1911         index += 4;
1912         for (section = 0; section < numsects; section++) {
1913                 baseaddress = sectstart[section];
1914                 thissectionsize = sectsize[section] >> 3;
1915
1916                 for (codeaddr = 0; codeaddr < thissectionsize; codeaddr++) {
1917                         /* Write out instruction address */
1918                         slic_reg32_write(&slic_regs->slic_wcs,
1919                                          baseaddress + codeaddr, FLUSH);
1920                         /* Write out instruction to low addr */
1921                         slic_reg32_write(&slic_regs->slic_wcs, instruction, FLUSH);
1922                         instruction = *(u32 *)(fw->data + index);
1923                         index += 4;
1924
1925                         /* Write out instruction to high addr */
1926                         slic_reg32_write(&slic_regs->slic_wcs, instruction, FLUSH);
1927                         instruction = *(u32 *)(fw->data + index);
1928                         index += 4;
1929                 }
1930         }
1931         index = ucode_start;
1932         for (section = 0; section < numsects; section++) {
1933                 instruction = *(u32 *)(fw->data + index);
1934                 baseaddress = sectstart[section];
1935                 if (baseaddress < 0x8000)
1936                         continue;
1937                 thissectionsize = sectsize[section] >> 3;
1938
1939                 for (codeaddr = 0; codeaddr < thissectionsize; codeaddr++) {
1940                         /* Write out instruction address */
1941                         slic_reg32_write(&slic_regs->slic_wcs,
1942                                 SLIC_WCS_COMPARE | (baseaddress + codeaddr),
1943                                 FLUSH);
1944                         /* Write out instruction to low addr */
1945                         slic_reg32_write(&slic_regs->slic_wcs, instruction,
1946                                          FLUSH);
1947                         instruction = *(u32 *)(fw->data + index);
1948                         index += 4;
1949                         /* Write out instruction to high addr */
1950                         slic_reg32_write(&slic_regs->slic_wcs, instruction,
1951                                          FLUSH);
1952                         instruction = *(u32 *)(fw->data + index);
1953                         index += 4;
1954
1955                         /* Check SRAM location zero. If it is non-zero. Abort.*/
1956 /*                      failure = readl((u32 __iomem *)&slic_regs->slic_reset);
1957                         if (failure) {
1958                                 release_firmware(fw);
1959                                 return -EIO;
1960                         }*/
1961                 }
1962         }
1963         release_firmware(fw);
1964         /* Everything OK, kick off the card */
1965         mdelay(10);
1966         slic_reg32_write(&slic_regs->slic_wcs, SLIC_WCS_START, FLUSH);
1967
1968         /* stall for 20 ms, long enough for ucode to init card
1969            and reach mainloop */
1970         mdelay(20);
1971
1972         return STATUS_SUCCESS;
1973 }
1974
1975 static void slic_adapter_set_hwaddr(struct adapter *adapter)
1976 {
1977         struct sliccard *card = adapter->card;
1978
1979         if ((adapter->card) && (card->config_set)) {
1980                 memcpy(adapter->macaddr,
1981                        card->config.MacInfo[adapter->functionnumber].macaddrA,
1982                        sizeof(struct slic_config_mac));
1983                 if (!(adapter->currmacaddr[0] || adapter->currmacaddr[1] ||
1984                       adapter->currmacaddr[2] || adapter->currmacaddr[3] ||
1985                       adapter->currmacaddr[4] || adapter->currmacaddr[5])) {
1986                         memcpy(adapter->currmacaddr, adapter->macaddr, 6);
1987                 }
1988                 if (adapter->netdev) {
1989                         memcpy(adapter->netdev->dev_addr, adapter->currmacaddr,
1990                                6);
1991                 }
1992         }
1993 }
1994
1995 static void slic_intagg_set(struct adapter *adapter, u32 value)
1996 {
1997         slic_reg32_write(&adapter->slic_regs->slic_intagg, value, FLUSH);
1998         adapter->card->loadlevel_current = value;
1999 }
2000
2001 static int slic_card_init(struct sliccard *card, struct adapter *adapter)
2002 {
2003         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2004         struct slic_eeprom *peeprom;
2005         struct oslic_eeprom *pOeeprom;
2006         dma_addr_t phys_config;
2007         u32 phys_configh;
2008         u32 phys_configl;
2009         u32 i = 0;
2010         struct slic_shmem *pshmem;
2011         int status;
2012         uint macaddrs = card->card_size;
2013         ushort eecodesize;
2014         ushort dramsize;
2015         ushort ee_chksum;
2016         ushort calc_chksum;
2017         struct slic_config_mac *pmac;
2018         unsigned char fruformat;
2019         unsigned char oemfruformat;
2020         struct atk_fru *patkfru;
2021         union oemfru *poemfru;
2022
2023         /* Reset everything except PCI configuration space */
2024         slic_soft_reset(adapter);
2025
2026         /* Download the microcode */
2027         status = slic_card_download(adapter);
2028
2029         if (status != STATUS_SUCCESS) {
2030                 dev_err(&adapter->pcidev->dev,
2031                         "download failed bus %d slot %d\n",
2032                         adapter->busnumber, adapter->slotnumber);
2033                 return status;
2034         }
2035
2036         if (!card->config_set) {
2037                 peeprom = pci_alloc_consistent(adapter->pcidev,
2038                                                sizeof(struct slic_eeprom),
2039                                                &phys_config);
2040
2041                 phys_configl = SLIC_GET_ADDR_LOW(phys_config);
2042                 phys_configh = SLIC_GET_ADDR_HIGH(phys_config);
2043
2044                 if (!peeprom) {
2045                         dev_err(&adapter->pcidev->dev,
2046                                 "eeprom read failed to get memory "
2047                                 "bus %d slot %d\n", adapter->busnumber,
2048                                 adapter->slotnumber);
2049                         return -ENOMEM;
2050                 } else {
2051                         memset(peeprom, 0, sizeof(struct slic_eeprom));
2052                 }
2053                 slic_reg32_write(&slic_regs->slic_icr, ICR_INT_OFF, FLUSH);
2054                 mdelay(1);
2055                 pshmem = (struct slic_shmem *)adapter->phys_shmem;
2056
2057                 spin_lock_irqsave(&adapter->bit64reglock.lock,
2058                                         adapter->bit64reglock.flags);
2059                 slic_reg32_write(&slic_regs->slic_addr_upper, 0, DONT_FLUSH);
2060                 slic_reg32_write(&slic_regs->slic_isp,
2061                                  SLIC_GET_ADDR_LOW(&pshmem->isr), FLUSH);
2062                 spin_unlock_irqrestore(&adapter->bit64reglock.lock,
2063                                         adapter->bit64reglock.flags);
2064
2065                 slic_config_get(adapter, phys_configl, phys_configh);
2066
2067                 for (;;) {
2068                         if (adapter->pshmem->isr) {
2069                                 if (adapter->pshmem->isr & ISR_UPC) {
2070                                         adapter->pshmem->isr = 0;
2071                                         slic_reg64_write(adapter,
2072                                                 &slic_regs->slic_isp, 0,
2073                                                 &slic_regs->slic_addr_upper,
2074                                                 0, FLUSH);
2075                                         slic_reg32_write(&slic_regs->slic_isr,
2076                                                          0, FLUSH);
2077
2078                                         slic_upr_request_complete(adapter, 0);
2079                                         break;
2080                                 } else {
2081                                         adapter->pshmem->isr = 0;
2082                                         slic_reg32_write(&slic_regs->slic_isr,
2083                                                          0, FLUSH);
2084                                 }
2085                         } else {
2086                                 mdelay(1);
2087                                 i++;
2088                                 if (i > 5000) {
2089                                         dev_err(&adapter->pcidev->dev,
2090                                                 "%d config data fetch timed out!\n",
2091                                                 adapter->port);
2092                                         slic_reg64_write(adapter,
2093                                                 &slic_regs->slic_isp, 0,
2094                                                 &slic_regs->slic_addr_upper,
2095                                                 0, FLUSH);
2096                                         return -EINVAL;
2097                                 }
2098                         }
2099                 }
2100
2101                 switch (adapter->devid) {
2102                 /* Oasis card */
2103                 case SLIC_2GB_DEVICE_ID:
2104                         /* extract EEPROM data and pointers to EEPROM data */
2105                         pOeeprom = (struct oslic_eeprom *) peeprom;
2106                         eecodesize = pOeeprom->EecodeSize;
2107                         dramsize = pOeeprom->DramSize;
2108                         pmac = pOeeprom->MacInfo;
2109                         fruformat = pOeeprom->FruFormat;
2110                         patkfru = &pOeeprom->AtkFru;
2111                         oemfruformat = pOeeprom->OemFruFormat;
2112                         poemfru = &pOeeprom->OemFru;
2113                         macaddrs = 2;
2114                         /* Minor kludge for Oasis card
2115                              get 2 MAC addresses from the
2116                              EEPROM to ensure that function 1
2117                              gets the Port 1 MAC address */
2118                         break;
2119                 default:
2120                         /* extract EEPROM data and pointers to EEPROM data */
2121                         eecodesize = peeprom->EecodeSize;
2122                         dramsize = peeprom->DramSize;
2123                         pmac = peeprom->u2.mac.MacInfo;
2124                         fruformat = peeprom->FruFormat;
2125                         patkfru = &peeprom->AtkFru;
2126                         oemfruformat = peeprom->OemFruFormat;
2127                         poemfru = &peeprom->OemFru;
2128                         break;
2129                 }
2130
2131                 card->config.EepromValid = false;
2132
2133                 /*  see if the EEPROM is valid by checking it's checksum */
2134                 if ((eecodesize <= MAX_EECODE_SIZE) &&
2135                     (eecodesize >= MIN_EECODE_SIZE)) {
2136
2137                         ee_chksum =
2138                             *(u16 *) ((char *) peeprom + (eecodesize - 2));
2139                         /*
2140                             calculate the EEPROM checksum
2141                         */
2142                         calc_chksum =
2143                             ~slic_eeprom_cksum((char *) peeprom,
2144                                                (eecodesize - 2));
2145                         /*
2146                             if the ucdoe chksum flag bit worked,
2147                             we wouldn't need this shit
2148                         */
2149                         if (ee_chksum == calc_chksum)
2150                                 card->config.EepromValid = true;
2151                 }
2152                 /*  copy in the DRAM size */
2153                 card->config.DramSize = dramsize;
2154
2155                 /*  copy in the MAC address(es) */
2156                 for (i = 0; i < macaddrs; i++) {
2157                         memcpy(&card->config.MacInfo[i],
2158                                &pmac[i], sizeof(struct slic_config_mac));
2159                 }
2160
2161                 /*  copy the Alacritech FRU information */
2162                 card->config.FruFormat = fruformat;
2163                 memcpy(&card->config.AtkFru, patkfru,
2164                                                 sizeof(struct atk_fru));
2165
2166                 pci_free_consistent(adapter->pcidev,
2167                                     sizeof(struct slic_eeprom),
2168                                     peeprom, phys_config);
2169
2170                 if ((!card->config.EepromValid) &&
2171                     (adapter->reg_params.fail_on_bad_eeprom)) {
2172                         slic_reg64_write(adapter, &slic_regs->slic_isp, 0,
2173                                          &slic_regs->slic_addr_upper,
2174                                          0, FLUSH);
2175                         dev_err(&adapter->pcidev->dev,
2176                                 "unsupported CONFIGURATION EEPROM invalid\n");
2177                         return -EINVAL;
2178                 }
2179
2180                 card->config_set = 1;
2181         }
2182
2183         if (slic_card_download_gbrcv(adapter)) {
2184                 dev_err(&adapter->pcidev->dev,
2185                         "unable to download GB receive microcode\n");
2186                 return -EINVAL;
2187         }
2188
2189         if (slic_global.dynamic_intagg)
2190                 slic_intagg_set(adapter, 0);
2191         else
2192                 slic_intagg_set(adapter, intagg_delay);
2193
2194         /*
2195          *  Initialize ping status to "ok"
2196          */
2197         card->pingstatus = ISR_PINGMASK;
2198
2199         /*
2200          * Lastly, mark our card state as up and return success
2201          */
2202         card->state = CARD_UP;
2203         card->reset_in_progress = 0;
2204
2205         return STATUS_SUCCESS;
2206 }
2207
2208 static u32 slic_card_locate(struct adapter *adapter)
2209 {
2210         struct sliccard *card = slic_global.slic_card;
2211         struct physcard *physcard = slic_global.phys_card;
2212         ushort card_hostid;
2213         u16 __iomem *hostid_reg;
2214         uint i;
2215         uint rdhostid_offset = 0;
2216
2217         switch (adapter->devid) {
2218         case SLIC_2GB_DEVICE_ID:
2219                 rdhostid_offset = SLIC_RDHOSTID_2GB;
2220                 break;
2221         case SLIC_1GB_DEVICE_ID:
2222                 rdhostid_offset = SLIC_RDHOSTID_1GB;
2223                 break;
2224         default:
2225                 ASSERT(0);
2226                 break;
2227         }
2228
2229         hostid_reg =
2230             (u16 __iomem *) (((u8 __iomem *) (adapter->slic_regs)) +
2231             rdhostid_offset);
2232
2233         /* read the 16 bit hostid from SRAM */
2234         card_hostid = (ushort) readw(hostid_reg);
2235
2236         /* Initialize a new card structure if need be */
2237         if (card_hostid == SLIC_HOSTID_DEFAULT) {
2238                 card = kzalloc(sizeof(struct sliccard), GFP_KERNEL);
2239                 if (card == NULL)
2240                         return -ENOMEM;
2241
2242                 card->next = slic_global.slic_card;
2243                 slic_global.slic_card = card;
2244                 card->busnumber = adapter->busnumber;
2245                 card->slotnumber = adapter->slotnumber;
2246
2247                 /* Find an available cardnum */
2248                 for (i = 0; i < SLIC_MAX_CARDS; i++) {
2249                         if (slic_global.cardnuminuse[i] == 0) {
2250                                 slic_global.cardnuminuse[i] = 1;
2251                                 card->cardnum = i;
2252                                 break;
2253                         }
2254                 }
2255                 slic_global.num_slic_cards++;
2256
2257                 slic_debug_card_create(card);
2258         } else {
2259                 /* Card exists, find the card this adapter belongs to */
2260                 while (card) {
2261                         if (card->cardnum == card_hostid)
2262                                 break;
2263                         card = card->next;
2264                 }
2265         }
2266
2267         ASSERT(card);
2268         if (!card)
2269                 return STATUS_FAILURE;
2270         /* Put the adapter in the card's adapter list */
2271         ASSERT(card->adapter[adapter->port] == NULL);
2272         if (!card->adapter[adapter->port]) {
2273                 card->adapter[adapter->port] = adapter;
2274                 adapter->card = card;
2275         }
2276
2277         card->card_size = 1;    /* one port per *logical* card */
2278
2279         while (physcard) {
2280                 for (i = 0; i < SLIC_MAX_PORTS; i++) {
2281                         if (!physcard->adapter[i])
2282                                 continue;
2283                         else
2284                                 break;
2285                 }
2286                 ASSERT(i != SLIC_MAX_PORTS);
2287                 if (physcard->adapter[i]->slotnumber == adapter->slotnumber)
2288                         break;
2289                 physcard = physcard->next;
2290         }
2291         if (!physcard) {
2292                 /* no structure allocated for this physical card yet */
2293                 physcard = kzalloc(sizeof(struct physcard), GFP_ATOMIC);
2294                 ASSERT(physcard);
2295
2296                 physcard->next = slic_global.phys_card;
2297                 slic_global.phys_card = physcard;
2298                 physcard->adapters_allocd = 1;
2299         } else {
2300                 physcard->adapters_allocd++;
2301         }
2302         /* Note - this is ZERO relative */
2303         adapter->physport = physcard->adapters_allocd - 1;
2304
2305         ASSERT(physcard->adapter[adapter->physport] == NULL);
2306         physcard->adapter[adapter->physport] = adapter;
2307         adapter->physcard = physcard;
2308
2309         return 0;
2310 }
2311
2312 static void slic_soft_reset(struct adapter *adapter)
2313 {
2314         if (adapter->card->state == CARD_UP) {
2315                 slic_reg32_write(&adapter->slic_regs->slic_quiesce, 0, FLUSH);
2316                 mdelay(1);
2317         }
2318
2319         slic_reg32_write(&adapter->slic_regs->slic_reset, SLIC_RESET_MAGIC,
2320                          FLUSH);
2321         mdelay(1);
2322 }
2323
2324 static void slic_config_set(struct adapter *adapter, bool linkchange)
2325 {
2326         u32 value;
2327         u32 RcrReset;
2328         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2329
2330         if (linkchange) {
2331                 /* Setup MAC */
2332                 slic_mac_config(adapter);
2333                 RcrReset = GRCR_RESET;
2334         } else {
2335                 slic_mac_address_config(adapter);
2336                 RcrReset = 0;
2337         }
2338
2339         if (adapter->linkduplex == LINK_FULLD) {
2340                 /* setup xmtcfg */
2341                 value = (GXCR_RESET |   /* Always reset     */
2342                          GXCR_XMTEN |   /* Enable transmit  */
2343                          GXCR_PAUSEEN); /* Enable pause     */
2344
2345                 slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH);
2346
2347                 /* Setup rcvcfg last */
2348                 value = (RcrReset |     /* Reset, if linkchange */
2349                          GRCR_CTLEN |   /* Enable CTL frames    */
2350                          GRCR_ADDRAEN | /* Address A enable     */
2351                          GRCR_RCVBAD |  /* Rcv bad frames       */
2352                          (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT));
2353         } else {
2354                 /* setup xmtcfg */
2355                 value = (GXCR_RESET |   /* Always reset     */
2356                          GXCR_XMTEN);   /* Enable transmit  */
2357
2358                 slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH);
2359
2360                 /* Setup rcvcfg last */
2361                 value = (RcrReset |     /* Reset, if linkchange */
2362                          GRCR_ADDRAEN | /* Address A enable     */
2363                          GRCR_RCVBAD |  /* Rcv bad frames       */
2364                          (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT));
2365         }
2366
2367         if (adapter->state != ADAPT_DOWN) {
2368                 /* Only enable receive if we are restarting or running */
2369                 value |= GRCR_RCVEN;
2370         }
2371
2372         if (adapter->macopts & MAC_PROMISC)
2373                 value |= GRCR_RCVALL;
2374
2375         slic_reg32_write(&slic_regs->slic_wrcfg, value, FLUSH);
2376 }
2377
2378 /*
2379  *  Turn off RCV and XMT, power down PHY
2380  */
2381 static void slic_config_clear(struct adapter *adapter)
2382 {
2383         u32 value;
2384         u32 phy_config;
2385         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2386
2387         /* Setup xmtcfg */
2388         value = (GXCR_RESET |   /* Always reset */
2389                  GXCR_PAUSEEN); /* Enable pause */
2390
2391         slic_reg32_write(&slic_regs->slic_wxcfg, value, FLUSH);
2392
2393         value = (GRCR_RESET |   /* Always reset      */
2394                  GRCR_CTLEN |   /* Enable CTL frames */
2395                  GRCR_ADDRAEN | /* Address A enable  */
2396                  (GRCR_HASHSIZE << GRCR_HASHSIZE_SHIFT));
2397
2398         slic_reg32_write(&slic_regs->slic_wrcfg, value, FLUSH);
2399
2400         /* power down phy */
2401         phy_config = (MIICR_REG_PCR | (PCR_POWERDOWN));
2402         slic_reg32_write(&slic_regs->slic_wphy, phy_config, FLUSH);
2403 }
2404
2405 static void slic_config_get(struct adapter *adapter, u32 config,
2406                                                         u32 config_h)
2407 {
2408         int status;
2409
2410         status = slic_upr_request(adapter,
2411                                   SLIC_UPR_RCONFIG,
2412                                   (u32) config, (u32) config_h, 0, 0);
2413         ASSERT(status == 0);
2414 }
2415
2416 static void slic_mac_address_config(struct adapter *adapter)
2417 {
2418         u32 value;
2419         u32 value2;
2420         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2421
2422         value = *(u32 *) &adapter->currmacaddr[2];
2423         value = ntohl(value);
2424         slic_reg32_write(&slic_regs->slic_wraddral, value, FLUSH);
2425         slic_reg32_write(&slic_regs->slic_wraddrbl, value, FLUSH);
2426
2427         value2 = (u32) ((adapter->currmacaddr[0] << 8 |
2428                              adapter->currmacaddr[1]) & 0xFFFF);
2429
2430         slic_reg32_write(&slic_regs->slic_wraddrah, value2, FLUSH);
2431         slic_reg32_write(&slic_regs->slic_wraddrbh, value2, FLUSH);
2432
2433         /* Write our multicast mask out to the card.  This is done */
2434         /* here in addition to the slic_mcast_addr_set routine     */
2435         /* because ALL_MCAST may have been enabled or disabled     */
2436         slic_mcast_set_mask(adapter);
2437 }
2438
2439 static void slic_mac_config(struct adapter *adapter)
2440 {
2441         u32 value;
2442         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2443
2444         /* Setup GMAC gaps */
2445         if (adapter->linkspeed == LINK_1000MB) {
2446                 value = ((GMCR_GAPBB_1000 << GMCR_GAPBB_SHIFT) |
2447                          (GMCR_GAPR1_1000 << GMCR_GAPR1_SHIFT) |
2448                          (GMCR_GAPR2_1000 << GMCR_GAPR2_SHIFT));
2449         } else {
2450                 value = ((GMCR_GAPBB_100 << GMCR_GAPBB_SHIFT) |
2451                          (GMCR_GAPR1_100 << GMCR_GAPR1_SHIFT) |
2452                          (GMCR_GAPR2_100 << GMCR_GAPR2_SHIFT));
2453         }
2454
2455         /* enable GMII */
2456         if (adapter->linkspeed == LINK_1000MB)
2457                 value |= GMCR_GBIT;
2458
2459         /* enable fullduplex */
2460         if ((adapter->linkduplex == LINK_FULLD)
2461             || (adapter->macopts & MAC_LOOPBACK)) {
2462                 value |= GMCR_FULLD;
2463         }
2464
2465         /* write mac config */
2466         slic_reg32_write(&slic_regs->slic_wmcfg, value, FLUSH);
2467
2468         /* setup mac addresses */
2469         slic_mac_address_config(adapter);
2470 }
2471
2472 static bool slic_mac_filter(struct adapter *adapter,
2473                         struct ether_header *ether_frame)
2474 {
2475         u32 opts = adapter->macopts;
2476         u32 *dhost4 = (u32 *)&ether_frame->ether_dhost[0];
2477         u16 *dhost2 = (u16 *)&ether_frame->ether_dhost[4];
2478         bool equaladdr;
2479
2480         if (opts & MAC_PROMISC)
2481                 return true;
2482
2483         if ((*dhost4 == 0xFFFFFFFF) && (*dhost2 == 0xFFFF)) {
2484                 if (opts & MAC_BCAST) {
2485                         adapter->rcv_broadcasts++;
2486                         return true;
2487                 } else {
2488                         return false;
2489                 }
2490         }
2491
2492         if (ether_frame->ether_dhost[0] & 0x01) {
2493                 if (opts & MAC_ALLMCAST) {
2494                         adapter->rcv_multicasts++;
2495                         adapter->stats.multicast++;
2496                         return true;
2497                 }
2498                 if (opts & MAC_MCAST) {
2499                         struct mcast_address *mcaddr = adapter->mcastaddrs;
2500
2501                         while (mcaddr) {
2502                                 ETHER_EQ_ADDR(mcaddr->address,
2503                                               ether_frame->ether_dhost,
2504                                               equaladdr);
2505                                 if (equaladdr) {
2506                                         adapter->rcv_multicasts++;
2507                                         adapter->stats.multicast++;
2508                                         return true;
2509                                 }
2510                                 mcaddr = mcaddr->next;
2511                         }
2512                         return false;
2513                 } else {
2514                         return false;
2515                 }
2516         }
2517         if (opts & MAC_DIRECTED) {
2518                 adapter->rcv_unicasts++;
2519                 return true;
2520         }
2521         return false;
2522
2523 }
2524
2525 static int slic_mac_set_address(struct net_device *dev, void *ptr)
2526 {
2527         struct adapter *adapter = (struct adapter *)netdev_priv(dev);
2528         struct sockaddr *addr = ptr;
2529
2530         if (netif_running(dev))
2531                 return -EBUSY;
2532         if (!adapter)
2533                 return -EBUSY;
2534
2535         memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
2536         memcpy(adapter->currmacaddr, addr->sa_data, dev->addr_len);
2537
2538         slic_config_set(adapter, true);
2539         return 0;
2540 }
2541
2542 static void slic_timer_load_check(ulong cardaddr)
2543 {
2544         struct sliccard *card = (struct sliccard *)cardaddr;
2545         struct adapter *adapter = card->master;
2546         u32 __iomem *intagg;
2547         u32 load = card->events;
2548         u32 level = 0;
2549
2550         intagg = &adapter->slic_regs->slic_intagg;
2551
2552         if ((adapter) && (adapter->state == ADAPT_UP) &&
2553             (card->state == CARD_UP) && (slic_global.dynamic_intagg)) {
2554                 if (adapter->devid == SLIC_1GB_DEVICE_ID) {
2555                         if (adapter->linkspeed == LINK_1000MB)
2556                                 level = 100;
2557                         else {
2558                                 if (load > SLIC_LOAD_5)
2559                                         level = SLIC_INTAGG_5;
2560                                 else if (load > SLIC_LOAD_4)
2561                                         level = SLIC_INTAGG_4;
2562                                 else if (load > SLIC_LOAD_3)
2563                                         level = SLIC_INTAGG_3;
2564                                 else if (load > SLIC_LOAD_2)
2565                                         level = SLIC_INTAGG_2;
2566                                 else if (load > SLIC_LOAD_1)
2567                                         level = SLIC_INTAGG_1;
2568                                 else
2569                                         level = SLIC_INTAGG_0;
2570                         }
2571                         if (card->loadlevel_current != level) {
2572                                 card->loadlevel_current = level;
2573                                 slic_reg32_write(intagg, level, FLUSH);
2574                         }
2575                 } else {
2576                         if (load > SLIC_LOAD_5)
2577                                 level = SLIC_INTAGG_5;
2578                         else if (load > SLIC_LOAD_4)
2579                                 level = SLIC_INTAGG_4;
2580                         else if (load > SLIC_LOAD_3)
2581                                 level = SLIC_INTAGG_3;
2582                         else if (load > SLIC_LOAD_2)
2583                                 level = SLIC_INTAGG_2;
2584                         else if (load > SLIC_LOAD_1)
2585                                 level = SLIC_INTAGG_1;
2586                         else
2587                                 level = SLIC_INTAGG_0;
2588                         if (card->loadlevel_current != level) {
2589                                 card->loadlevel_current = level;
2590                                 slic_reg32_write(intagg, level, FLUSH);
2591                         }
2592                 }
2593         }
2594         card->events = 0;
2595         card->loadtimer.expires = jiffies + (SLIC_LOADTIMER_PERIOD * HZ);
2596         add_timer(&card->loadtimer);
2597 }
2598
2599 static void slic_assert_fail(void)
2600 {
2601         u32 cpuid;
2602         u32 curr_pid;
2603         cpuid = smp_processor_id();
2604         curr_pid = current->pid;
2605
2606         printk(KERN_ERR "%s CPU # %d ---- PID # %d\n",
2607                __func__, cpuid, curr_pid);
2608 }
2609
2610 static int slic_upr_queue_request(struct adapter *adapter,
2611                            u32 upr_request,
2612                            u32 upr_data,
2613                            u32 upr_data_h,
2614                            u32 upr_buffer, u32 upr_buffer_h)
2615 {
2616         struct slic_upr *upr;
2617         struct slic_upr *uprqueue;
2618
2619         upr = kmalloc(sizeof(struct slic_upr), GFP_ATOMIC);
2620         if (!upr)
2621                 return -ENOMEM;
2622
2623         upr->adapter = adapter->port;
2624         upr->upr_request = upr_request;
2625         upr->upr_data = upr_data;
2626         upr->upr_buffer = upr_buffer;
2627         upr->upr_data_h = upr_data_h;
2628         upr->upr_buffer_h = upr_buffer_h;
2629         upr->next = NULL;
2630         if (adapter->upr_list) {
2631                 uprqueue = adapter->upr_list;
2632
2633                 while (uprqueue->next)
2634                         uprqueue = uprqueue->next;
2635                 uprqueue->next = upr;
2636         } else {
2637                 adapter->upr_list = upr;
2638         }
2639         return STATUS_SUCCESS;
2640 }
2641
2642 static int slic_upr_request(struct adapter *adapter,
2643                      u32 upr_request,
2644                      u32 upr_data,
2645                      u32 upr_data_h,
2646                      u32 upr_buffer, u32 upr_buffer_h)
2647 {
2648         int status;
2649
2650         spin_lock_irqsave(&adapter->upr_lock.lock, adapter->upr_lock.flags);
2651         status = slic_upr_queue_request(adapter,
2652                                         upr_request,
2653                                         upr_data,
2654                                         upr_data_h, upr_buffer, upr_buffer_h);
2655         if (status != STATUS_SUCCESS) {
2656                 spin_unlock_irqrestore(&adapter->upr_lock.lock,
2657                                         adapter->upr_lock.flags);
2658                 return status;
2659         }
2660         slic_upr_start(adapter);
2661         spin_unlock_irqrestore(&adapter->upr_lock.lock,
2662                                 adapter->upr_lock.flags);
2663         return STATUS_PENDING;
2664 }
2665
2666 static void slic_upr_request_complete(struct adapter *adapter, u32 isr)
2667 {
2668         struct sliccard *card = adapter->card;
2669         struct slic_upr *upr;
2670
2671         spin_lock_irqsave(&adapter->upr_lock.lock, adapter->upr_lock.flags);
2672         upr = adapter->upr_list;
2673         if (!upr) {
2674                 ASSERT(0);
2675                 spin_unlock_irqrestore(&adapter->upr_lock.lock,
2676                                         adapter->upr_lock.flags);
2677                 return;
2678         }
2679         adapter->upr_list = upr->next;
2680         upr->next = NULL;
2681         adapter->upr_busy = 0;
2682         ASSERT(adapter->port == upr->adapter);
2683         switch (upr->upr_request) {
2684         case SLIC_UPR_STATS:
2685                 {
2686                         struct slic_stats *slicstats =
2687                             (struct slic_stats *) &adapter->pshmem->inicstats;
2688                         struct slic_stats *newstats = slicstats;
2689                         struct slic_stats  *old = &adapter->inicstats_prev;
2690                         struct slicnet_stats *stst = &adapter->slic_stats;
2691
2692                         if (isr & ISR_UPCERR) {
2693                                 dev_err(&adapter->netdev->dev,
2694                                         "SLIC_UPR_STATS command failed isr[%x]\n",
2695                                         isr);
2696
2697                                 break;
2698                         }
2699                         UPDATE_STATS_GB(stst->tcp.xmit_tcp_segs,
2700                                         newstats->xmit_tcp_segs_gb,
2701                                         old->xmit_tcp_segs_gb);
2702
2703                         UPDATE_STATS_GB(stst->tcp.xmit_tcp_bytes,
2704                                         newstats->xmit_tcp_bytes_gb,
2705                                         old->xmit_tcp_bytes_gb);
2706
2707                         UPDATE_STATS_GB(stst->tcp.rcv_tcp_segs,
2708                                         newstats->rcv_tcp_segs_gb,
2709                                         old->rcv_tcp_segs_gb);
2710
2711                         UPDATE_STATS_GB(stst->tcp.rcv_tcp_bytes,
2712                                         newstats->rcv_tcp_bytes_gb,
2713                                         old->rcv_tcp_bytes_gb);
2714
2715                         UPDATE_STATS_GB(stst->iface.xmt_bytes,
2716                                         newstats->xmit_bytes_gb,
2717                                         old->xmit_bytes_gb);
2718
2719                         UPDATE_STATS_GB(stst->iface.xmt_ucast,
2720                                         newstats->xmit_unicasts_gb,
2721                                         old->xmit_unicasts_gb);
2722
2723                         UPDATE_STATS_GB(stst->iface.rcv_bytes,
2724                                         newstats->rcv_bytes_gb,
2725                                         old->rcv_bytes_gb);
2726
2727                         UPDATE_STATS_GB(stst->iface.rcv_ucast,
2728                                         newstats->rcv_unicasts_gb,
2729                                         old->rcv_unicasts_gb);
2730
2731                         UPDATE_STATS_GB(stst->iface.xmt_errors,
2732                                         newstats->xmit_collisions_gb,
2733                                         old->xmit_collisions_gb);
2734
2735                         UPDATE_STATS_GB(stst->iface.xmt_errors,
2736                                         newstats->xmit_excess_collisions_gb,
2737                                         old->xmit_excess_collisions_gb);
2738
2739                         UPDATE_STATS_GB(stst->iface.xmt_errors,
2740                                         newstats->xmit_other_error_gb,
2741                                         old->xmit_other_error_gb);
2742
2743                         UPDATE_STATS_GB(stst->iface.rcv_errors,
2744                                         newstats->rcv_other_error_gb,
2745                                         old->rcv_other_error_gb);
2746
2747                         UPDATE_STATS_GB(stst->iface.rcv_discards,
2748                                         newstats->rcv_drops_gb,
2749                                         old->rcv_drops_gb);
2750
2751                         if (newstats->rcv_drops_gb > old->rcv_drops_gb) {
2752                                 adapter->rcv_drops +=
2753                                     (newstats->rcv_drops_gb -
2754                                      old->rcv_drops_gb);
2755                         }
2756                         memcpy(old, newstats, sizeof(struct slic_stats));
2757                         break;
2758                 }
2759         case SLIC_UPR_RLSR:
2760                 slic_link_upr_complete(adapter, isr);
2761                 break;
2762         case SLIC_UPR_RCONFIG:
2763                 break;
2764         case SLIC_UPR_RPHY:
2765                 ASSERT(0);
2766                 break;
2767         case SLIC_UPR_ENLB:
2768                 ASSERT(0);
2769                 break;
2770         case SLIC_UPR_ENCT:
2771                 ASSERT(0);
2772                 break;
2773         case SLIC_UPR_PDWN:
2774                 ASSERT(0);
2775                 break;
2776         case SLIC_UPR_PING:
2777                 card->pingstatus |= (isr & ISR_PINGDSMASK);
2778                 break;
2779         default:
2780                 ASSERT(0);
2781         }
2782         kfree(upr);
2783         slic_upr_start(adapter);
2784         spin_unlock_irqrestore(&adapter->upr_lock.lock,
2785                                 adapter->upr_lock.flags);
2786 }
2787
2788 static void slic_upr_start(struct adapter *adapter)
2789 {
2790         struct slic_upr *upr;
2791         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
2792 /*
2793     char * ptr1;
2794     char * ptr2;
2795     uint cmdoffset;
2796 */
2797         upr = adapter->upr_list;
2798         if (!upr)
2799                 return;
2800         if (adapter->upr_busy)
2801                 return;
2802         adapter->upr_busy = 1;
2803
2804         switch (upr->upr_request) {
2805         case SLIC_UPR_STATS:
2806                 if (upr->upr_data_h == 0) {
2807                         slic_reg32_write(&slic_regs->slic_stats, upr->upr_data,
2808                                          FLUSH);
2809                 } else {
2810                         slic_reg64_write(adapter, &slic_regs->slic_stats64,
2811                                          upr->upr_data,
2812                                          &slic_regs->slic_addr_upper,
2813                                          upr->upr_data_h, FLUSH);
2814                 }
2815                 break;
2816
2817         case SLIC_UPR_RLSR:
2818                 slic_reg64_write(adapter, &slic_regs->slic_rlsr, upr->upr_data,
2819                                  &slic_regs->slic_addr_upper, upr->upr_data_h,
2820                                  FLUSH);
2821                 break;
2822
2823         case SLIC_UPR_RCONFIG:
2824                 slic_reg64_write(adapter, &slic_regs->slic_rconfig,
2825                                  upr->upr_data, &slic_regs->slic_addr_upper,
2826                                  upr->upr_data_h, FLUSH);
2827                 break;
2828         case SLIC_UPR_PING:
2829                 slic_reg32_write(&slic_regs->slic_ping, 1, FLUSH);
2830                 break;
2831         default:
2832                 ASSERT(0);
2833         }
2834 }
2835
2836 static void slic_link_upr_complete(struct adapter *adapter, u32 isr)
2837 {
2838         u32 linkstatus = adapter->pshmem->linkstatus;
2839         uint linkup;
2840         unsigned char linkspeed;
2841         unsigned char linkduplex;
2842
2843         if ((isr & ISR_UPCERR) || (isr & ISR_UPCBSY)) {
2844                 struct slic_shmem *pshmem;
2845
2846                 pshmem = (struct slic_shmem *)adapter->phys_shmem;
2847 #if defined(CONFIG_X86_64)
2848                 slic_upr_queue_request(adapter,
2849                                        SLIC_UPR_RLSR,
2850                                        SLIC_GET_ADDR_LOW(&pshmem->linkstatus),
2851                                        SLIC_GET_ADDR_HIGH(&pshmem->linkstatus),
2852                                        0, 0);
2853 #elif defined(CONFIG_X86)
2854                 slic_upr_queue_request(adapter,
2855                                        SLIC_UPR_RLSR,
2856                                        (u32) &pshmem->linkstatus,
2857                                        SLIC_GET_ADDR_HIGH(pshmem), 0, 0);
2858 #else
2859                 Stop Compilation;
2860 #endif
2861                 return;
2862         }
2863         if (adapter->state != ADAPT_UP)
2864                 return;
2865
2866         ASSERT((adapter->devid == SLIC_1GB_DEVICE_ID)
2867                || (adapter->devid == SLIC_2GB_DEVICE_ID));
2868
2869         linkup = linkstatus & GIG_LINKUP ? LINK_UP : LINK_DOWN;
2870         if (linkstatus & GIG_SPEED_1000)
2871                 linkspeed = LINK_1000MB;
2872         else if (linkstatus & GIG_SPEED_100)
2873                 linkspeed = LINK_100MB;
2874         else
2875                 linkspeed = LINK_10MB;
2876
2877         if (linkstatus & GIG_FULLDUPLEX)
2878                 linkduplex = LINK_FULLD;
2879         else
2880                 linkduplex = LINK_HALFD;
2881
2882         if ((adapter->linkstate == LINK_DOWN) && (linkup == LINK_DOWN))
2883                 return;
2884
2885         /* link up event, but nothing has changed */
2886         if ((adapter->linkstate == LINK_UP) &&
2887             (linkup == LINK_UP) &&
2888             (adapter->linkspeed == linkspeed) &&
2889             (adapter->linkduplex == linkduplex))
2890                 return;
2891
2892         /* link has changed at this point */
2893
2894         /* link has gone from up to down */
2895         if (linkup == LINK_DOWN) {
2896                 adapter->linkstate = LINK_DOWN;
2897                 return;
2898         }
2899
2900         /* link has gone from down to up */
2901         adapter->linkspeed = linkspeed;
2902         adapter->linkduplex = linkduplex;
2903
2904         if (adapter->linkstate != LINK_UP) {
2905                 /* setup the mac */
2906                 slic_config_set(adapter, true);
2907                 adapter->linkstate = LINK_UP;
2908                 netif_start_queue(adapter->netdev);
2909         }
2910 }
2911
2912 /*
2913  *  this is here to checksum the eeprom, there is some ucode bug
2914  *  which prevens us from using the ucode result.
2915  *  remove this once ucode is fixed.
2916  */
2917 static ushort slic_eeprom_cksum(char *m, int len)
2918 {
2919 #define ADDCARRY(x)  (x > 65535 ? x -= 65535 : x)
2920 #define REDUCE {l_util.l = sum; sum = l_util.s[0] + l_util.s[1]; ADDCARRY(sum);\
2921                 }
2922
2923         u16 *w;
2924         u32 sum = 0;
2925         u32 byte_swapped = 0;
2926         u32 w_int;
2927
2928         union {
2929                 char c[2];
2930                 ushort s;
2931         } s_util;
2932
2933         union {
2934                 ushort s[2];
2935                 int l;
2936         } l_util;
2937
2938         l_util.l = 0;
2939         s_util.s = 0;
2940
2941         w = (u16 *)m;
2942 #ifdef CONFIG_X86_64
2943         w_int = (u32) ((ulong) w & 0x00000000FFFFFFFF);
2944 #else
2945         w_int = (u32) (w);
2946 #endif
2947         if ((1 & w_int) && (len > 0)) {
2948                 REDUCE;
2949                 sum <<= 8;
2950                 s_util.c[0] = *(unsigned char *)w;
2951                 w = (u16 *)((char *)w + 1);
2952                 len--;
2953                 byte_swapped = 1;
2954         }
2955
2956         /* Unroll the loop to make overhead from branches &c small. */
2957         while ((len -= 32) >= 0) {
2958                 sum += w[0];
2959                 sum += w[1];
2960                 sum += w[2];
2961                 sum += w[3];
2962                 sum += w[4];
2963                 sum += w[5];
2964                 sum += w[6];
2965                 sum += w[7];
2966                 sum += w[8];
2967                 sum += w[9];
2968                 sum += w[10];
2969                 sum += w[11];
2970                 sum += w[12];
2971                 sum += w[13];
2972                 sum += w[14];
2973                 sum += w[15];
2974                 w = (u16 *)((ulong) w + 16);    /* verify */
2975         }
2976         len += 32;
2977         while ((len -= 8) >= 0) {
2978                 sum += w[0];
2979                 sum += w[1];
2980                 sum += w[2];
2981                 sum += w[3];
2982                 w = (u16 *)((ulong) w + 4);     /* verify */
2983         }
2984         len += 8;
2985         if (len != 0 || byte_swapped != 0) {
2986                 REDUCE;
2987                 while ((len -= 2) >= 0)
2988                         sum += *w++;    /* verify */
2989                 if (byte_swapped) {
2990                         REDUCE;
2991                         sum <<= 8;
2992                         byte_swapped = 0;
2993                         if (len == -1) {
2994                                 s_util.c[1] = *(char *) w;
2995                                 sum += s_util.s;
2996                                 len = 0;
2997                         } else {
2998                                 len = -1;
2999                         }
3000
3001                 } else if (len == -1) {
3002                         s_util.c[0] = *(char *) w;
3003                 }
3004
3005                 if (len == -1) {
3006                         s_util.c[1] = 0;
3007                         sum += s_util.s;
3008                 }
3009         }
3010         REDUCE;
3011         return (ushort) sum;
3012 }
3013
3014 static int slic_rspqueue_init(struct adapter *adapter)
3015 {
3016         int i;
3017         struct slic_rspqueue *rspq = &adapter->rspqueue;
3018         __iomem struct slic_regs *slic_regs = adapter->slic_regs;
3019         u32 paddrh = 0;
3020
3021         ASSERT(adapter->state == ADAPT_DOWN);
3022         memset(rspq, 0, sizeof(struct slic_rspqueue));
3023
3024         rspq->num_pages = SLIC_RSPQ_PAGES_GB;
3025
3026         for (i = 0; i < rspq->num_pages; i++) {
3027                 rspq->vaddr[i] = pci_alloc_consistent(adapter->pcidev,
3028                                                       PAGE_SIZE,
3029                                                       &rspq->paddr[i]);
3030                 if (!rspq->vaddr[i]) {
3031                         dev_err(&adapter->pcidev->dev,
3032                                 "pci_alloc_consistent failed\n");
3033                         slic_rspqueue_free(adapter);
3034                         return STATUS_FAILURE;
3035                 }
3036 #ifndef CONFIG_X86_64
3037                 ASSERT(((u32) rspq->vaddr[i] & 0xFFFFF000) ==
3038                        (u32) rspq->vaddr[i]);
3039                 ASSERT(((u32) rspq->paddr[i] & 0xFFFFF000) ==
3040                        (u32) rspq->paddr[i]);
3041 #endif
3042                 memset(rspq->vaddr[i], 0, PAGE_SIZE);
3043
3044                 if (paddrh == 0) {
3045                         slic_reg32_write(&slic_regs->slic_rbar,
3046                                 (rspq->paddr[i] | SLIC_RSPQ_BUFSINPAGE),
3047                                 DONT_FLUSH);
3048                 } else {
3049                         slic_reg64_write(adapter, &slic_regs->slic_rbar64,
3050                                 (rspq->paddr[i] | SLIC_RSPQ_BUFSINPAGE),
3051                                 &slic_regs->slic_addr_upper,
3052                                 paddrh, DONT_FLUSH);
3053                 }
3054         }
3055         rspq->offset = 0;
3056         rspq->pageindex = 0;
3057         rspq->rspbuf = (struct slic_rspbuf *)rspq->vaddr[0];
3058         return STATUS_SUCCESS;
3059 }
3060
3061 static void slic_rspqueue_free(struct adapter *adapter)
3062 {
3063         int i;
3064         struct slic_rspqueue *rspq = &adapter->rspqueue;
3065
3066         for (i = 0; i < rspq->num_pages; i++) {
3067                 if (rspq->vaddr[i]) {
3068                         pci_free_consistent(adapter->pcidev, PAGE_SIZE,
3069                                             rspq->vaddr[i], rspq->paddr[i]);
3070                 }
3071                 rspq->vaddr[i] = NULL;
3072                 rspq->paddr[i] = 0;
3073         }
3074         rspq->offset = 0;
3075         rspq->pageindex = 0;
3076         rspq->rspbuf = NULL;
3077 }
3078
3079 static struct slic_rspbuf *slic_rspqueue_getnext(struct adapter *adapter)
3080 {
3081         struct slic_rspqueue *rspq = &adapter->rspqueue;
3082         struct slic_rspbuf *buf;
3083
3084         if (!(rspq->rspbuf->status))
3085                 return NULL;
3086
3087         buf = rspq->rspbuf;
3088 #ifndef CONFIG_X86_64
3089         ASSERT((buf->status & 0xFFFFFFE0) == 0);
3090 #endif
3091         ASSERT(buf->hosthandle);
3092         if (++rspq->offset < SLIC_RSPQ_BUFSINPAGE) {
3093                 rspq->rspbuf++;
3094 #ifndef CONFIG_X86_64
3095                 ASSERT(((u32) rspq->rspbuf & 0xFFFFFFE0) ==
3096                        (u32) rspq->rspbuf);
3097 #endif
3098         } else {
3099                 ASSERT(rspq->offset == SLIC_RSPQ_BUFSINPAGE);
3100                 slic_reg64_write(adapter, &adapter->slic_regs->slic_rbar64,
3101                         (rspq->paddr[rspq->pageindex] | SLIC_RSPQ_BUFSINPAGE),
3102                         &adapter->slic_regs->slic_addr_upper, 0, DONT_FLUSH);
3103                 rspq->pageindex = (++rspq->pageindex) % rspq->num_pages;
3104                 rspq->offset = 0;
3105                 rspq->rspbuf = (struct slic_rspbuf *)
3106                                                 rspq->vaddr[rspq->pageindex];
3107 #ifndef CONFIG_X86_64
3108                 ASSERT(((u32) rspq->rspbuf & 0xFFFFF000) ==
3109                        (u32) rspq->rspbuf);
3110 #endif
3111         }
3112 #ifndef CONFIG_X86_64
3113         ASSERT(((u32) buf & 0xFFFFFFE0) == (u32) buf);
3114 #endif
3115         return buf;
3116 }
3117
3118 static void slic_cmdqmem_init(struct adapter *adapter)
3119 {
3120         struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem;
3121
3122         memset(cmdqmem, 0, sizeof(struct slic_cmdqmem));
3123 }
3124
3125 static void slic_cmdqmem_free(struct adapter *adapter)
3126 {
3127         struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem;
3128         int i;
3129
3130         for (i = 0; i < SLIC_CMDQ_MAXPAGES; i++) {
3131                 if (cmdqmem->pages[i]) {
3132                         pci_free_consistent(adapter->pcidev,
3133                                             PAGE_SIZE,
3134                                             (void *) cmdqmem->pages[i],
3135                                             cmdqmem->dma_pages[i]);
3136                 }
3137         }
3138         memset(cmdqmem, 0, sizeof(struct slic_cmdqmem));
3139 }
3140
3141 static u32 *slic_cmdqmem_addpage(struct adapter *adapter)
3142 {
3143         struct slic_cmdqmem *cmdqmem = &adapter->cmdqmem;
3144         u32 *pageaddr;
3145
3146         if (cmdqmem->pagecnt >= SLIC_CMDQ_MAXPAGES)
3147                 return NULL;
3148         pageaddr = pci_alloc_consistent(adapter->pcidev,
3149                                         PAGE_SIZE,
3150                                         &cmdqmem->dma_pages[cmdqmem->pagecnt]);
3151         if (!pageaddr)
3152                 return NULL;
3153 #ifndef CONFIG_X86_64
3154         ASSERT(((u32) pageaddr & 0xFFFFF000) == (u32) pageaddr);
3155 #endif
3156         cmdqmem->pages[cmdqmem->pagecnt] = pageaddr;
3157         cmdqmem->pagecnt++;
3158         return pageaddr;
3159 }
3160
3161 static int slic_cmdq_init(struct adapter *adapter)
3162 {
3163         int i;
3164         u32 *pageaddr;
3165
3166         ASSERT(adapter->state == ADAPT_DOWN);
3167         memset(&adapter->cmdq_all, 0, sizeof(struct slic_cmdqueue));
3168         memset(&adapter->cmdq_free, 0, sizeof(struct slic_cmdqueue));
3169         memset(&adapter->cmdq_done, 0, sizeof(struct slic_cmdqueue));
3170         spin_lock_init(&adapter->cmdq_all.lock.lock);
3171         spin_lock_init(&adapter->cmdq_free.lock.lock);
3172         spin_lock_init(&adapter->cmdq_done.lock.lock);
3173         slic_cmdqmem_init(adapter);
3174         adapter->slic_handle_ix = 1;
3175         for (i = 0; i < SLIC_CMDQ_INITPAGES; i++) {
3176                 pageaddr = slic_cmdqmem_addpage(adapter);
3177 #ifndef CONFIG_X86_64
3178                 ASSERT(((u32) pageaddr & 0xFFFFF000) == (u32) pageaddr);
3179 #endif
3180                 if (!pageaddr) {
3181                         slic_cmdq_free(adapter);
3182                         return STATUS_FAILURE;
3183                 }
3184                 slic_cmdq_addcmdpage(adapter, pageaddr);
3185         }
3186         adapter->slic_handle_ix = 1;
3187
3188         return STATUS_SUCCESS;
3189 }
3190
3191 static void slic_cmdq_free(struct adapter *adapter)
3192 {
3193         struct slic_hostcmd *cmd;
3194
3195         cmd = adapter->cmdq_all.head;
3196         while (cmd) {
3197                 if (cmd->busy) {
3198                         struct sk_buff *tempskb;
3199
3200                         tempskb = cmd->skb;
3201                         if (tempskb) {
3202                                 cmd->skb = NULL;
3203                                 dev_kfree_skb_irq(tempskb);
3204                         }
3205                 }
3206                 cmd = cmd->next_all;
3207         }
3208         memset(&adapter->cmdq_all, 0, sizeof(struct slic_cmdqueue));
3209         memset(&adapter->cmdq_free, 0, sizeof(struct slic_cmdqueue));
3210         memset(&adapter->cmdq_done, 0, sizeof(struct slic_cmdqueue));
3211         slic_cmdqmem_free(adapter);
3212 }
3213
3214 static void slic_cmdq_reset(struct adapter *adapter)
3215 {
3216         struct slic_hostcmd *hcmd;
3217         struct sk_buff *skb;
3218         u32 outstanding;
3219
3220         spin_lock_irqsave(&adapter->cmdq_free.lock.lock,
3221                         adapter->cmdq_free.lock.flags);
3222         spin_lock_irqsave(&adapter->cmdq_done.lock.lock,
3223                         adapter->cmdq_done.lock.flags);
3224         outstanding = adapter->cmdq_all.count - adapter->cmdq_done.count;
3225         outstanding -= adapter->cmdq_free.count;
3226         hcmd = adapter->cmdq_all.head;
3227         while (hcmd) {
3228                 if (hcmd->busy) {
3229                         skb = hcmd->skb;
3230                         ASSERT(skb);
3231                         hcmd->busy = 0;
3232                         hcmd->skb = NULL;
3233                         dev_kfree_skb_irq(skb);
3234                 }
3235                 hcmd = hcmd->next_all;
3236         }
3237         adapter->cmdq_free.count = 0;
3238         adapter->cmdq_free.head = NULL;
3239         adapter->cmdq_free.tail = NULL;
3240         adapter->cmdq_done.count = 0;
3241         adapter->cmdq_done.head = NULL;
3242         adapter->cmdq_done.tail = NULL;
3243         adapter->cmdq_free.head = adapter->cmdq_all.head;
3244         hcmd = adapter->cmdq_all.head;
3245         while (hcmd) {
3246                 adapter->cmdq_free.count++;
3247                 hcmd->next = hcmd->next_all;
3248                 hcmd = hcmd->next_all;
3249         }
3250         if (adapter->cmdq_free.count != adapter->cmdq_all.count) {
3251                 dev_err(&adapter->netdev->dev,
3252                         "free_count %d != all count %d\n",
3253                         adapter->cmdq_free.count, adapter->cmdq_all.count);
3254         }
3255         spin_unlock_irqrestore(&adapter->cmdq_done.lock.lock,
3256                                 adapter->cmdq_done.lock.flags);
3257         spin_unlock_irqrestore(&adapter->cmdq_free.lock.lock,
3258                                 adapter->cmdq_free.lock.flags);
3259 }
3260
3261 static void slic_cmdq_addcmdpage(struct adapter *adapter, u32 *page)
3262 {
3263         struct slic_hostcmd *cmd;
3264         struct slic_hostcmd *prev;
3265         struct slic_hostcmd *tail;
3266         struct slic_cmdqueue *cmdq;
3267         int cmdcnt;
3268         void *cmdaddr;
3269         ulong phys_addr;
3270         u32 phys_addrl;
3271         u32 phys_addrh;
3272         struct slic_handle *pslic_handle;
3273
3274         cmdaddr = page;
3275         cmd = (struct slic_hostcmd *)cmdaddr;
3276         cmdcnt = 0;
3277
3278         phys_addr = virt_to_bus((void *)page);
3279         phys_addrl = SLIC_GET_ADDR_LOW(phys_addr);
3280         phys_addrh = SLIC_GET_ADDR_HIGH(phys_addr);
3281
3282         prev = NULL;
3283         tail = cmd;
3284         while ((cmdcnt < SLIC_CMDQ_CMDSINPAGE) &&
3285                (adapter->slic_handle_ix < 256)) {
3286                 /* Allocate and initialize a SLIC_HANDLE for this command */
3287                 SLIC_GET_SLIC_HANDLE(adapter, pslic_handle);
3288                 if (pslic_handle == NULL)
3289                         ASSERT(0);
3290                 ASSERT(pslic_handle ==
3291                        &adapter->slic_handles[pslic_handle->token.
3292                                               handle_index]);
3293                 pslic_handle->type = SLIC_HANDLE_CMD;
3294                 pslic_handle->address = (void *) cmd;
3295                 pslic_handle->offset = (ushort) adapter->slic_handle_ix++;
3296                 pslic_handle->other_handle = NULL;
3297                 pslic_handle->next = NULL;
3298
3299                 cmd->pslic_handle = pslic_handle;
3300                 cmd->cmd64.hosthandle = pslic_handle->token.handle_token;
3301                 cmd->busy = false;
3302                 cmd->paddrl = phys_addrl;
3303                 cmd->paddrh = phys_addrh;
3304                 cmd->next_all = prev;
3305                 cmd->next = prev;
3306                 prev = cmd;
3307                 phys_addrl += SLIC_HOSTCMD_SIZE;
3308                 cmdaddr += SLIC_HOSTCMD_SIZE;
3309
3310                 cmd = (struct slic_hostcmd *)cmdaddr;
3311                 cmdcnt++;
3312         }
3313
3314         cmdq = &adapter->cmdq_all;
3315         cmdq->count += cmdcnt;  /*  SLIC_CMDQ_CMDSINPAGE;   mooktodo */
3316         tail->next_all = cmdq->head;
3317         cmdq->head = prev;
3318         cmdq = &adapter->cmdq_free;
3319         spin_lock_irqsave(&cmdq->lock.lock, cmdq->lock.flags);
3320         cmdq->count += cmdcnt;  /*  SLIC_CMDQ_CMDSINPAGE;   mooktodo */
3321         tail->next = cmdq->head;
3322         cmdq->head = prev;
3323         spin_unlock_irqrestore(&cmdq->lock.lock, cmdq->lock.flags);
3324 }
3325
3326 static struct slic_hostcmd *slic_cmdq_getfree(struct adapter *adapter)
3327 {
3328         struct slic_cmdqueue *cmdq = &adapter->cmdq_free;
3329         struct slic_hostcmd *cmd = NULL;
3330
3331 lock_and_retry:
3332         spin_lock_irqsave(&cmdq->lock.lock, cmdq->lock.flags);
3333 retry:
3334         cmd = cmdq->head;
3335         if (cmd) {
3336                 cmdq->head = cmd->next;
3337                 cmdq->count--;
3338                 spin_unlock_irqrestore(&cmdq->lock.lock, cmdq->lock.flags);
3339         } else {
3340                 slic_cmdq_getdone(adapter);
3341                 cmd = cmdq->head;
3342                 if (cmd) {
3343                         goto retry;
3344                 } else {
3345                         u32 *pageaddr;
3346
3347                         spin_unlock_irqrestore(&cmdq->lock.lock,
3348                                                 cmdq->lock.flags);
3349                         pageaddr = slic_cmdqmem_addpage(adapter);
3350                         if (pageaddr) {
3351                                 slic_cmdq_addcmdpage(adapter, pageaddr);
3352                                 goto lock_and_retry;
3353                         }
3354                 }
3355         }
3356         return cmd;
3357 }
3358
3359 static void slic_cmdq_getdone(struct adapter *adapter)
3360 {
3361         struct slic_cmdqueue *done_cmdq = &adapter->cmdq_done;
3362         struct slic_cmdqueue *free_cmdq = &adapter->cmdq_free;
3363
3364         ASSERT(free_cmdq->head == NULL);
3365         spin_lock_irqsave(&done_cmdq->lock.lock, done_cmdq->lock.flags);
3366
3367         free_cmdq->head = done_cmdq->head;
3368         free_cmdq->count = done_cmdq->count;
3369         done_cmdq->head = NULL;
3370         done_cmdq->tail = NULL;
3371         done_cmdq->count = 0;
3372         spin_unlock_irqrestore(&done_cmdq->lock.lock, done_cmdq->lock.flags);
3373 }
3374
3375 static void slic_cmdq_putdone_irq(struct adapter *adapter,
3376                                 struct slic_hostcmd *cmd)
3377 {
3378         struct slic_cmdqueue *cmdq = &adapter->cmdq_done;
3379
3380         spin_lock(&cmdq->lock.lock);
3381         cmd->busy = 0;
3382         cmd->next = cmdq->head;
3383         cmdq->head = cmd;
3384         cmdq->count++;
3385         if ((adapter->xmitq_full) && (cmdq->count > 10))
3386                 netif_wake_queue(adapter->netdev);
3387         spin_unlock(&cmdq->lock.lock);
3388 }
3389
3390 static int slic_rcvqueue_init(struct adapter *adapter)
3391 {
3392         int i, count;
3393         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3394
3395         ASSERT(adapter->state == ADAPT_DOWN);
3396         rcvq->tail = NULL;
3397         rcvq->head = NULL;
3398         rcvq->size = SLIC_RCVQ_ENTRIES;
3399         rcvq->errors = 0;
3400         rcvq->count = 0;
3401         i = (SLIC_RCVQ_ENTRIES / SLIC_RCVQ_FILLENTRIES);
3402         count = 0;
3403         while (i) {
3404                 count += slic_rcvqueue_fill(adapter);
3405                 i--;
3406         }
3407         if (rcvq->count < SLIC_RCVQ_MINENTRIES) {
3408                 slic_rcvqueue_free(adapter);
3409                 return STATUS_FAILURE;
3410         }
3411         return STATUS_SUCCESS;
3412 }
3413
3414 static void slic_rcvqueue_free(struct adapter *adapter)
3415 {
3416         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3417         struct sk_buff *skb;
3418
3419         while (rcvq->head) {
3420                 skb = rcvq->head;
3421                 rcvq->head = rcvq->head->next;
3422                 dev_kfree_skb(skb);
3423         }
3424         rcvq->tail = NULL;
3425         rcvq->head = NULL;
3426         rcvq->count = 0;
3427 }
3428
3429 static struct sk_buff *slic_rcvqueue_getnext(struct adapter *adapter)
3430 {
3431         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3432         struct sk_buff *skb;
3433         struct slic_rcvbuf *rcvbuf;
3434         int count;
3435
3436         if (rcvq->count) {
3437                 skb = rcvq->head;
3438                 rcvbuf = (struct slic_rcvbuf *)skb->head;
3439                 ASSERT(rcvbuf);
3440
3441                 if (rcvbuf->status & IRHDDR_SVALID) {
3442                         rcvq->head = rcvq->head->next;
3443                         skb->next = NULL;
3444                         rcvq->count--;
3445                 } else {
3446                         skb = NULL;
3447                 }
3448         } else {
3449                 dev_err(&adapter->netdev->dev,
3450                         "RcvQ Empty!! rcvq[%p] count[%x]\n", rcvq, rcvq->count);
3451                 skb = NULL;
3452         }
3453         while (rcvq->count < SLIC_RCVQ_FILLTHRESH) {
3454                 count = slic_rcvqueue_fill(adapter);
3455                 if (!count)
3456                         break;
3457         }
3458         if (skb)
3459                 rcvq->errors = 0;
3460         return skb;
3461 }
3462
3463 static int slic_rcvqueue_fill(struct adapter *adapter)
3464 {
3465         void *paddr;
3466         u32 paddrl;
3467         u32 paddrh;
3468         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3469         int i = 0;
3470         struct device *dev = &adapter->netdev->dev;
3471
3472         while (i < SLIC_RCVQ_FILLENTRIES) {
3473                 struct slic_rcvbuf *rcvbuf;
3474                 struct sk_buff *skb;
3475 #ifdef KLUDGE_FOR_4GB_BOUNDARY
3476 retry_rcvqfill:
3477 #endif
3478                 skb = alloc_skb(SLIC_RCVQ_RCVBUFSIZE, GFP_ATOMIC);
3479                 if (skb) {
3480                         paddr = (void *)pci_map_single(adapter->pcidev,
3481                                                           skb->data,
3482                                                           SLIC_RCVQ_RCVBUFSIZE,
3483                                                           PCI_DMA_FROMDEVICE);
3484                         paddrl = SLIC_GET_ADDR_LOW(paddr);
3485                         paddrh = SLIC_GET_ADDR_HIGH(paddr);
3486
3487                         skb->len = SLIC_RCVBUF_HEADSIZE;
3488                         rcvbuf = (struct slic_rcvbuf *)skb->head;
3489                         rcvbuf->status = 0;
3490                         skb->next = NULL;
3491 #ifdef KLUDGE_FOR_4GB_BOUNDARY
3492                         if (paddrl == 0) {
3493                                 dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n",
3494                                         __func__);
3495                                 dev_err(dev, "skb[%p] PROBLEM\n", skb);
3496                                 dev_err(dev, "         skbdata[%p]\n", skb->data);
3497                                 dev_err(dev, "         skblen[%x]\n", skb->len);
3498                                 dev_err(dev, "         paddr[%p]\n", paddr);
3499                                 dev_err(dev, "         paddrl[%x]\n", paddrl);
3500                                 dev_err(dev, "         paddrh[%x]\n", paddrh);
3501                                 dev_err(dev, "         rcvq->head[%p]\n", rcvq->head);
3502                                 dev_err(dev, "         rcvq->tail[%p]\n", rcvq->tail);
3503                                 dev_err(dev, "         rcvq->count[%x]\n", rcvq->count);
3504                                 dev_err(dev, "SKIP THIS SKB!!!!!!!!\n");
3505                                 goto retry_rcvqfill;
3506                         }
3507 #else
3508                         if (paddrl == 0) {
3509                                 dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n",
3510                                         __func__);
3511                                 dev_err(dev, "skb[%p] PROBLEM\n", skb);
3512                                 dev_err(dev, "         skbdata[%p]\n", skb->data);
3513                                 dev_err(dev, "         skblen[%x]\n", skb->len);
3514                                 dev_err(dev, "         paddr[%p]\n", paddr);
3515                                 dev_err(dev, "         paddrl[%x]\n", paddrl);
3516                                 dev_err(dev, "         paddrh[%x]\n", paddrh);
3517                                 dev_err(dev, "         rcvq->head[%p]\n", rcvq->head);
3518                                 dev_err(dev, "         rcvq->tail[%p]\n", rcvq->tail);
3519                                 dev_err(dev, "         rcvq->count[%x]\n", rcvq->count);
3520                                 dev_err(dev, "GIVE TO CARD ANYWAY\n");
3521                         }
3522 #endif
3523                         if (paddrh == 0) {
3524                                 slic_reg32_write(&adapter->slic_regs->slic_hbar,
3525                                                  (u32)paddrl, DONT_FLUSH);
3526                         } else {
3527                                 slic_reg64_write(adapter,
3528                                         &adapter->slic_regs->slic_hbar64,
3529                                         paddrl,
3530                                         &adapter->slic_regs->slic_addr_upper,
3531                                         paddrh, DONT_FLUSH);
3532                         }
3533                         if (rcvq->head)
3534                                 rcvq->tail->next = skb;
3535                         else
3536                                 rcvq->head = skb;
3537                         rcvq->tail = skb;
3538                         rcvq->count++;
3539                         i++;
3540                 } else {
3541                         dev_err(&adapter->netdev->dev,
3542                                 "slic_rcvqueue_fill could only get [%d] skbuffs\n",
3543                                 i);
3544                         break;
3545                 }
3546         }
3547         return i;
3548 }
3549
3550 static u32 slic_rcvqueue_reinsert(struct adapter *adapter, struct sk_buff *skb)
3551 {
3552         struct slic_rcvqueue *rcvq = &adapter->rcvqueue;
3553         void *paddr;
3554         u32 paddrl;
3555         u32 paddrh;
3556         struct slic_rcvbuf *rcvbuf = (struct slic_rcvbuf *)skb->head;
3557         struct device *dev;
3558
3559         ASSERT(skb->len == SLIC_RCVBUF_HEADSIZE);
3560
3561         paddr = (void *)pci_map_single(adapter->pcidev, skb->head,
3562                                   SLIC_RCVQ_RCVBUFSIZE, PCI_DMA_FROMDEVICE);
3563         rcvbuf->status = 0;
3564         skb->next = NULL;
3565
3566         paddrl = SLIC_GET_ADDR_LOW(paddr);
3567         paddrh = SLIC_GET_ADDR_HIGH(paddr);
3568
3569         if (paddrl == 0) {
3570                 dev = &adapter->netdev->dev;
3571                 dev_err(dev, "%s: LOW 32bits PHYSICAL ADDRESS == 0\n",
3572                         __func__);
3573                 dev_err(dev, "skb[%p] PROBLEM\n", skb);
3574                 dev_err(dev, "         skbdata[%p]\n", skb->data);
3575                 dev_err(dev, "         skblen[%x]\n", skb->len);
3576                 dev_err(dev, "         paddr[%p]\n", paddr);
3577                 dev_err(dev, "         paddrl[%x]\n", paddrl);
3578                 dev_err(dev, "         paddrh[%x]\n", paddrh);
3579                 dev_err(dev, "         rcvq->head[%p]\n", rcvq->head);
3580                 dev_err(dev, "         rcvq->tail[%p]\n", rcvq->tail);
3581                 dev_err(dev, "         rcvq->count[%x]\n", rcvq->count);
3582         }
3583         if (paddrh == 0) {
3584                 slic_reg32_write(&adapter->slic_regs->slic_hbar, (u32)paddrl,
3585                                  DONT_FLUSH);
3586         } else {
3587                 slic_reg64_write(adapter, &adapter->slic_regs->slic_hbar64,
3588                                  paddrl, &adapter->slic_regs->slic_addr_upper,
3589                                  paddrh, DONT_FLUSH);
3590         }
3591         if (rcvq->head)
3592                 rcvq->tail->next = skb;
3593         else
3594                 rcvq->head = skb;
3595         rcvq->tail = skb;
3596         rcvq->count++;
3597         return rcvq->count;
3598 }
3599
3600 static int slic_debug_card_show(struct seq_file *seq, void *v)
3601 {
3602 #ifdef MOOKTODO
3603         int i;
3604         struct sliccard *card = seq->private;
3605         struct slic_config *config = &card->config;
3606         unsigned char *fru = (unsigned char *)(&card->config.atk_fru);
3607         unsigned char *oemfru = (unsigned char *)(&card->config.OemFru);
3608 #endif
3609
3610         seq_printf(seq, "driver_version           : %s\n", slic_proc_version);
3611         seq_printf(seq, "Microcode versions:           \n");
3612         seq_printf(seq, "    Gigabit (gb)         : %s %s\n",
3613                     MOJAVE_UCODE_VERS_STRING, MOJAVE_UCODE_VERS_DATE);
3614         seq_printf(seq, "    Gigabit Receiver     : %s %s\n",
3615                     GB_RCVUCODE_VERS_STRING, GB_RCVUCODE_VERS_DATE);
3616         seq_printf(seq, "Vendor                   : %s\n", slic_vendor);
3617         seq_printf(seq, "Product Name             : %s\n", slic_product_name);
3618 #ifdef MOOKTODO
3619         seq_printf(seq, "VendorId                 : %4.4X\n",
3620                     config->VendorId);
3621         seq_printf(seq, "DeviceId                 : %4.4X\n",
3622                     config->DeviceId);
3623         seq_printf(seq, "RevisionId               : %2.2x\n",
3624                     config->RevisionId);
3625         seq_printf(seq, "Bus    #                 : %d\n", card->busnumber);
3626         seq_printf(seq, "Device #                 : %d\n", card->slotnumber);
3627         seq_printf(seq, "Interfaces               : %d\n", card->card_size);
3628         seq_printf(seq, "     Initialized         : %d\n",
3629                     card->adapters_activated);
3630         seq_printf(seq, "     Allocated           : %d\n",
3631                     card->adapters_allocated);
3632         ASSERT(card->card_size <= SLIC_NBR_MACS);
3633         for (i = 0; i < card->card_size; i++) {
3634                 seq_printf(seq,
3635                            "     MAC%d : %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
3636                            i, config->macinfo[i].macaddrA[0],
3637                            config->macinfo[i].macaddrA[1],
3638                            config->macinfo[i].macaddrA[2],
3639                            config->macinfo[i].macaddrA[3],
3640                            config->macinfo[i].macaddrA[4],
3641                            config->macinfo[i].macaddrA[5]);
3642         }
3643         seq_printf(seq, "     IF  Init State Duplex/Speed irq\n");
3644         seq_printf(seq, "     -------------------------------\n");
3645         for (i = 0; i < card->adapters_allocated; i++) {
3646                 struct adapter *adapter;
3647
3648                 adapter = card->adapter[i];
3649                 if (adapter) {
3650                         seq_printf(seq,
3651                                     "     %d   %d   %s  %s  %s    0x%X\n",
3652                                     adapter->physport, adapter->state,
3653                                     SLIC_LINKSTATE(adapter->linkstate),
3654                                     SLIC_DUPLEX(adapter->linkduplex),
3655                                     SLIC_SPEED(adapter->linkspeed),
3656                                     (uint) adapter->irq);
3657                 }
3658         }
3659         seq_printf(seq, "Generation #             : %4.4X\n", card->gennumber);
3660         seq_printf(seq, "RcvQ max entries         : %4.4X\n",
3661                     SLIC_RCVQ_ENTRIES);
3662         seq_printf(seq, "Ping Status              : %8.8X\n",
3663                     card->pingstatus);
3664         seq_printf(seq, "Minimum grant            : %2.2x\n",
3665                     config->MinGrant);
3666         seq_printf(seq, "Maximum Latency          : %2.2x\n", config->MaxLat);
3667         seq_printf(seq, "PciStatus                : %4.4x\n",
3668                     config->Pcistatus);
3669         seq_printf(seq, "Debug Device Id          : %4.4x\n",
3670                     config->DbgDevId);
3671         seq_printf(seq, "DRAM ROM Function        : %4.4x\n",
3672                     config->DramRomFn);
3673         seq_printf(seq, "Network interface Pin 1  : %2.2x\n",
3674                     config->NetIntPin1);
3675         seq_printf(seq, "Network interface Pin 2  : %2.2x\n",
3676                     config->NetIntPin1);
3677         seq_printf(seq, "Network interface Pin 3  : %2.2x\n",
3678                     config->NetIntPin1);
3679         seq_printf(seq, "PM capabilities          : %4.4X\n",
3680                     config->PMECapab);
3681         seq_printf(seq, "Network Clock Controls   : %4.4X\n",
3682                     config->NwClkCtrls);
3683
3684         switch (config->FruFormat) {
3685         case ATK_FRU_FORMAT:
3686                 {
3687                         seq_printf(seq,
3688                             "Vendor                   : Alacritech, Inc.\n");
3689                         seq_printf(seq,
3690                             "Assembly #               : %c%c%c%c%c%c\n",
3691                                     fru[0], fru[1], fru[2], fru[3], fru[4],
3692                                     fru[5]);
3693                         seq_printf(seq,
3694                                     "Revision #               : %c%c\n",
3695                                     fru[6], fru[7]);
3696
3697                         if (config->OEMFruFormat == VENDOR4_FRU_FORMAT) {
3698                                 seq_printf(seq,
3699                                             "Serial   #               : "
3700                                             "%c%c%c%c%c%c%c%c%c%c%c%c\n",
3701                                             fru[8], fru[9], fru[10],
3702                                             fru[11], fru[12], fru[13],
3703                                             fru[16], fru[17], fru[18],
3704                                             fru[19], fru[20], fru[21]);
3705                         } else {
3706                                 seq_printf(seq,
3707                                             "Serial   #               : "
3708                                             "%c%c%c%c%c%c%c%c%c%c%c%c%c%c\n",
3709                                             fru[8], fru[9], fru[10],
3710                                             fru[11], fru[12], fru[13],
3711                                             fru[14], fru[15], fru[16],
3712                                             fru[17], fru[18], fru[19],
3713                                             fru[20], fru[21]);
3714                         }
3715                         break;
3716                 }
3717
3718         default:
3719                 {
3720                         seq_printf(seq,
3721                             "Vendor                   : Alacritech, Inc.\n");
3722                         seq_printf(seq,
3723                             "Serial   #               : Empty FRU\n");
3724                         break;
3725                 }
3726         }
3727
3728         switch (config->OEMFruFormat) {
3729         case VENDOR1_FRU_FORMAT:
3730                 {
3731                         seq_printf(seq, "FRU Information:\n");
3732                         seq_printf(seq, "    Commodity #          : %c\n",
3733                                     oemfru[0]);
3734                         seq_printf(seq,
3735                                     "    Assembly #           : %c%c%c%c\n",
3736                                     oemfru[1], oemfru[2], oemfru[3], oemfru[4]);
3737                         seq_printf(seq,
3738                                     "    Revision #           : %c%c\n",
3739                                     oemfru[5], oemfru[6]);
3740                         seq_printf(seq,
3741                                     "    Supplier #           : %c%c\n",
3742                                     oemfru[7], oemfru[8]);
3743                         seq_printf(seq,
3744                                     "    Date                 : %c%c\n",
3745                                     oemfru[9], oemfru[10]);
3746                         seq_sprintf(seq,
3747                                     "    Sequence #           : %c%c%c\n",
3748                                     oemfru[11], oemfru[12], oemfru[13]);
3749                         break;
3750                 }
3751
3752         case VENDOR2_FRU_FORMAT:
3753                 {
3754                         seq_printf(seq, "FRU Information:\n");
3755                         seq_printf(seq,
3756                                     "    Part     #           : "
3757                                     "%c%c%c%c%c%c%c%c\n",
3758                                     oemfru[0], oemfru[1], oemfru[2],
3759                                     oemfru[3], oemfru[4], oemfru[5],
3760                                     oemfru[6], oemfru[7]);
3761                         seq_printf(seq,
3762                                     "    Supplier #           : %c%c%c%c%c\n",
3763                                     oemfru[8], oemfru[9], oemfru[10],
3764                                     oemfru[11], oemfru[12]);
3765                         seq_printf(seq,
3766                                     "    Date                 : %c%c%c\n",
3767                                     oemfru[13], oemfru[14], oemfru[15]);
3768                         seq_sprintf(seq,
3769                                     "    Sequence #           : %c%c%c%c\n",
3770                                     oemfru[16], oemfru[17], oemfru[18],
3771                                     oemfru[19]);
3772                         break;
3773                 }
3774
3775         case VENDOR3_FRU_FORMAT:
3776                 {
3777                         seq_printf(seq, "FRU Information:\n");
3778                 }
3779
3780         case VENDOR4_FRU_FORMAT:
3781                 {
3782                         seq_printf(seq, "FRU Information:\n");
3783                         seq_printf(seq,
3784                                     "    FRU Number           : "
3785                                     "%c%c%c%c%c%c%c%c\n",
3786                                     oemfru[0], oemfru[1], oemfru[2],
3787                                     oemfru[3], oemfru[4], oemfru[5],
3788                                     oemfru[6], oemfru[7]);
3789                         seq_sprintf(seq,
3790                                     "    Part Number          : "
3791                                     "%c%c%c%c%c%c%c%c\n",
3792                                     oemfru[8], oemfru[9], oemfru[10],
3793                                     oemfru[11], oemfru[12], oemfru[13],
3794                                     oemfru[14], oemfru[15]);
3795                         seq_printf(seq,
3796                                     "    EC Level             : "
3797                                     "%c%c%c%c%c%c%c%c\n",
3798                                     oemfru[16], oemfru[17], oemfru[18],
3799                                     oemfru[19], oemfru[20], oemfru[21],
3800                                     oemfru[22], oemfru[23]);
3801                         break;
3802                 }
3803
3804         default:
3805                 break;
3806         }
3807 #endif
3808
3809         return 0;
3810 }
3811
3812 static int slic_debug_adapter_show(struct seq_file *seq, void *v)
3813 {
3814         struct adapter *adapter = seq->private;
3815
3816         if ((adapter->netdev) && (adapter->netdev->name)) {
3817                 seq_printf(seq, "info: interface          : %s\n",
3818                             adapter->netdev->name);
3819         }
3820         seq_printf(seq, "info: status             : %s\n",
3821                 SLIC_LINKSTATE(adapter->linkstate));
3822         seq_printf(seq, "info: port               : %d\n",
3823                 adapter->physport);
3824         seq_printf(seq, "info: speed              : %s\n",
3825                 SLIC_SPEED(adapter->linkspeed));
3826         seq_printf(seq, "info: duplex             : %s\n",
3827                 SLIC_DUPLEX(adapter->linkduplex));
3828         seq_printf(seq, "info: irq                : 0x%X\n",
3829                 (uint) adapter->irq);
3830         seq_printf(seq, "info: Interrupt Agg Delay: %d usec\n",
3831                 adapter->card->loadlevel_current);
3832         seq_printf(seq, "info: RcvQ max entries   : %4.4X\n",
3833                 SLIC_RCVQ_ENTRIES);
3834         seq_printf(seq, "info: RcvQ current       : %4.4X\n",
3835                     adapter->rcvqueue.count);
3836         seq_printf(seq, "rx stats: packets                  : %8.8lX\n",
3837                     adapter->stats.rx_packets);
3838         seq_printf(seq, "rx stats: bytes                    : %8.8lX\n",
3839                     adapter->stats.rx_bytes);
3840         seq_printf(seq, "rx stats: broadcasts               : %8.8X\n",
3841                     adapter->rcv_broadcasts);
3842         seq_printf(seq, "rx stats: multicasts               : %8.8X\n",
3843                     adapter->rcv_multicasts);
3844         seq_printf(seq, "rx stats: unicasts                 : %8.8X\n",
3845                     adapter->rcv_unicasts);
3846         seq_printf(seq, "rx stats: errors                   : %8.8X\n",
3847                     (u32) adapter->slic_stats.iface.rcv_errors);
3848         seq_printf(seq, "rx stats: Missed errors            : %8.8X\n",
3849                     (u32) adapter->slic_stats.iface.rcv_discards);
3850         seq_printf(seq, "rx stats: drops                    : %8.8X\n",
3851                         (u32) adapter->rcv_drops);
3852         seq_printf(seq, "tx stats: packets                  : %8.8lX\n",
3853                         adapter->stats.tx_packets);
3854         seq_printf(seq, "tx stats: bytes                    : %8.8lX\n",
3855                         adapter->stats.tx_bytes);
3856         seq_printf(seq, "tx stats: errors                   : %8.8X\n",
3857                         (u32) adapter->slic_stats.iface.xmt_errors);
3858         seq_printf(seq, "rx stats: multicasts               : %8.8lX\n",
3859                         adapter->stats.multicast);
3860         seq_printf(seq, "tx stats: collision errors         : %8.8X\n",
3861                         (u32) adapter->slic_stats.iface.xmit_collisions);
3862         seq_printf(seq, "perf: Max rcv frames/isr           : %8.8X\n",
3863                         adapter->max_isr_rcvs);
3864         seq_printf(seq, "perf: Rcv interrupt yields         : %8.8X\n",
3865                         adapter->rcv_interrupt_yields);
3866         seq_printf(seq, "perf: Max xmit complete/isr        : %8.8X\n",
3867                         adapter->max_isr_xmits);
3868         seq_printf(seq, "perf: error interrupts             : %8.8X\n",
3869                         adapter->error_interrupts);
3870         seq_printf(seq, "perf: error rmiss interrupts       : %8.8X\n",
3871                         adapter->error_rmiss_interrupts);
3872         seq_printf(seq, "perf: rcv interrupts               : %8.8X\n",
3873                         adapter->rcv_interrupts);
3874         seq_printf(seq, "perf: xmit interrupts              : %8.8X\n",
3875                         adapter->xmit_interrupts);
3876         seq_printf(seq, "perf: link event interrupts        : %8.8X\n",
3877                         adapter->linkevent_interrupts);
3878         seq_printf(seq, "perf: UPR interrupts               : %8.8X\n",
3879                         adapter->upr_interrupts);
3880         seq_printf(seq, "perf: interrupt count              : %8.8X\n",
3881                         adapter->num_isrs);
3882         seq_printf(seq, "perf: false interrupts             : %8.8X\n",
3883                         adapter->false_interrupts);
3884         seq_printf(seq, "perf: All register writes          : %8.8X\n",
3885                         adapter->all_reg_writes);
3886         seq_printf(seq, "perf: ICR register writes          : %8.8X\n",
3887                         adapter->icr_reg_writes);
3888         seq_printf(seq, "perf: ISR register writes          : %8.8X\n",
3889                         adapter->isr_reg_writes);
3890         seq_printf(seq, "ifevents: overflow 802 errors      : %8.8X\n",
3891                         adapter->if_events.oflow802);
3892         seq_printf(seq, "ifevents: transport overflow errors: %8.8X\n",
3893                         adapter->if_events.Tprtoflow);
3894         seq_printf(seq, "ifevents: underflow errors         : %8.8X\n",
3895                         adapter->if_events.uflow802);
3896         seq_printf(seq, "ifevents: receive early            : %8.8X\n",
3897                         adapter->if_events.rcvearly);
3898         seq_printf(seq, "ifevents: buffer overflows         : %8.8X\n",
3899                         adapter->if_events.Bufov);
3900         seq_printf(seq, "ifevents: carrier errors           : %8.8X\n",
3901                         adapter->if_events.Carre);
3902         seq_printf(seq, "ifevents: Long                     : %8.8X\n",
3903                         adapter->if_events.Longe);
3904         seq_printf(seq, "ifevents: invalid preambles        : %8.8X\n",
3905                         adapter->if_events.Invp);
3906         seq_printf(seq, "ifevents: CRC errors               : %8.8X\n",
3907                         adapter->if_events.Crc);
3908         seq_printf(seq, "ifevents: dribble nibbles          : %8.8X\n",
3909                         adapter->if_events.Drbl);
3910         seq_printf(seq, "ifevents: Code violations          : %8.8X\n",
3911                         adapter->if_events.Code);
3912         seq_printf(seq, "ifevents: TCP checksum errors      : %8.8X\n",
3913                         adapter->if_events.TpCsum);
3914         seq_printf(seq, "ifevents: TCP header short errors  : %8.8X\n",
3915                         adapter->if_events.TpHlen);
3916         seq_printf(seq, "ifevents: IP checksum errors       : %8.8X\n",
3917                         adapter->if_events.IpCsum);
3918         seq_printf(seq, "ifevents: IP frame incompletes     : %8.8X\n",
3919                         adapter->if_events.IpLen);
3920         seq_printf(seq, "ifevents: IP headers shorts        : %8.8X\n",
3921                         adapter->if_events.IpHlen);
3922
3923         return 0;
3924 }
3925 static int slic_debug_adapter_open(struct inode *inode, struct file *file)
3926 {
3927         return single_open(file, slic_debug_adapter_show, inode->i_private);
3928 }
3929
3930 static int slic_debug_card_open(struct inode *inode, struct file *file)
3931 {
3932         return single_open(file, slic_debug_card_show, inode->i_private);
3933 }
3934
3935 static const struct file_operations slic_debug_adapter_fops = {
3936         .owner          = THIS_MODULE,
3937         .open           = slic_debug_adapter_open,
3938         .read           = seq_read,
3939         .llseek         = seq_lseek,
3940         .release        = single_release,
3941 };
3942
3943 static const struct file_operations slic_debug_card_fops = {
3944         .owner          = THIS_MODULE,
3945         .open           = slic_debug_card_open,
3946         .read           = seq_read,
3947         .llseek         = seq_lseek,
3948         .release        = single_release,
3949 };
3950
3951 static void slic_debug_adapter_create(struct adapter *adapter)
3952 {
3953         struct dentry *d;
3954         char    name[7];
3955         struct sliccard *card = adapter->card;
3956
3957         if (!card->debugfs_dir)
3958                 return;
3959
3960         sprintf(name, "port%d", adapter->port);
3961         d = debugfs_create_file(name, S_IRUGO,
3962                                 card->debugfs_dir, adapter,
3963                                 &slic_debug_adapter_fops);
3964         if (!d || IS_ERR(d))
3965                 pr_info(PFX "%s: debugfs create failed\n", name);
3966         else
3967                 adapter->debugfs_entry = d;
3968 }
3969
3970 static void slic_debug_adapter_destroy(struct adapter *adapter)
3971 {
3972         if (adapter->debugfs_entry) {
3973                 debugfs_remove(adapter->debugfs_entry);
3974                 adapter->debugfs_entry = NULL;
3975         }
3976 }
3977
3978 static void slic_debug_card_create(struct sliccard *card)
3979 {
3980         struct dentry *d;
3981         char    name[IFNAMSIZ];
3982
3983         snprintf(name, sizeof(name), "slic%d", card->cardnum);
3984         d = debugfs_create_dir(name, slic_debugfs);
3985         if (!d || IS_ERR(d))
3986                 pr_info(PFX "%s: debugfs create dir failed\n",
3987                                 name);
3988         else {
3989                 card->debugfs_dir = d;
3990                 d = debugfs_create_file("cardinfo", S_IRUGO,
3991                                 slic_debugfs, card,
3992                                 &slic_debug_card_fops);
3993                 if (!d || IS_ERR(d))
3994                         pr_info(PFX "%s: debugfs create failed\n",
3995                                         name);
3996                 else
3997                         card->debugfs_cardinfo = d;
3998         }
3999 }
4000
4001 static void slic_debug_card_destroy(struct sliccard *card)
4002 {
4003         int i;
4004
4005         for (i = 0; i < card->card_size; i++) {
4006                 struct adapter *adapter;
4007
4008                 adapter = card->adapter[i];
4009                 if (adapter)
4010                         slic_debug_adapter_destroy(adapter);
4011         }
4012         if (card->debugfs_cardinfo) {
4013                 debugfs_remove(card->debugfs_cardinfo);
4014                 card->debugfs_cardinfo = NULL;
4015         }
4016         if (card->debugfs_dir) {
4017                 debugfs_remove(card->debugfs_dir);
4018                 card->debugfs_dir = NULL;
4019         }
4020 }
4021
4022 static void slic_debug_init(void)
4023 {
4024         struct dentry *ent;
4025
4026         ent = debugfs_create_dir("slic", NULL);
4027         if (!ent || IS_ERR(ent)) {
4028                 pr_info(PFX "debugfs create directory failed\n");
4029                 return;
4030         }
4031
4032         slic_debugfs = ent;
4033 }
4034
4035 static void slic_debug_cleanup(void)
4036 {
4037         if (slic_debugfs) {
4038                 debugfs_remove(slic_debugfs);
4039                 slic_debugfs = NULL;
4040         }
4041 }
4042
4043 /******************************************************************************/
4044 /****************   MODULE INITIATION / TERMINATION FUNCTIONS   ***************/
4045 /******************************************************************************/
4046
4047 static struct pci_driver slic_driver = {
4048         .name = DRV_NAME,
4049         .id_table = slic_pci_tbl,
4050         .probe = slic_entry_probe,
4051         .remove = __devexit_p(slic_entry_remove),
4052 };
4053
4054 static int __init slic_module_init(void)
4055 {
4056         slic_init_driver();
4057
4058         if (debug >= 0 && slic_debug != debug)
4059                 printk(KERN_DEBUG KBUILD_MODNAME ": debug level is %d.\n",
4060                        debug);
4061         if (debug >= 0)
4062                 slic_debug = debug;
4063
4064         return pci_register_driver(&slic_driver);
4065 }
4066
4067 static void __exit slic_module_cleanup(void)
4068 {
4069         pci_unregister_driver(&slic_driver);
4070         slic_debug_cleanup();
4071 }
4072
4073 module_init(slic_module_init);
4074 module_exit(slic_module_cleanup);