wimax: allow specifying debug levels as command line option

[safe/jmp/linux-2.6] / drivers / net / wimax / i2400m / driver.c

/*
 * Intel Wireless WiMAX Connection 2400m
 * Generic probe/disconnect, reset and message passing
 *
 *
 * Copyright (C) 2007-2008 Intel Corporation <linux-wimax@intel.com>
 * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License version
 * 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
 * 02110-1301, USA.
 *
 *
 * See i2400m.h for driver documentation. This contains helpers for
 * the driver model glue [_setup()/_release()], handling device resets
 * [_dev_reset_handle()], and the backends for the WiMAX stack ops
 * reset [_op_reset()] and message from user [_op_msg_from_user()].
 *
 * ROADMAP:
 *
 * i2400m_op_msg_from_user()
 *   i2400m_msg_to_dev()
 *   wimax_msg_to_user_send()
 *
 * i2400m_op_reset()
 *   i240m->bus_reset()
 *
 * i2400m_dev_reset_handle()
 *   __i2400m_dev_reset_handle()
 *     __i2400m_dev_stop()
 *     __i2400m_dev_start()
 *
 * i2400m_setup()
 *   i2400m_bootrom_init()
 *   register_netdev()
 *   i2400m_dev_start()
 *     __i2400m_dev_start()
 *       i2400m_dev_bootstrap()
 *       i2400m_tx_setup()
 *       i2400m->bus_dev_start()
 *       i2400m_firmware_check()
 *       i2400m_check_mac_addr()
 *   wimax_dev_add()
 *
 * i2400m_release()
 *   wimax_dev_rm()
 *   i2400m_dev_stop()
 *     __i2400m_dev_stop()
 *       i2400m_dev_shutdown()
 *       i2400m->bus_dev_stop()
 *       i2400m_tx_release()
 *   unregister_netdev()
 */
#include "i2400m.h"
#include <linux/etherdevice.h>
#include <linux/wimax/i2400m.h>
#include <linux/module.h>
#include <linux/moduleparam.h>

#define D_SUBMODULE driver
#include "debug-levels.h"


int i2400m_idle_mode_disabled;  /* 0 (idle mode enabled) by default */
module_param_named(idle_mode_disabled, i2400m_idle_mode_disabled, int, 0644);
MODULE_PARM_DESC(idle_mode_disabled,
                 "If true, the device will not enable idle mode negotiation "
                 "with the base station (when connected) to save power.");

int i2400m_rx_reorder_disabled; /* 0 (rx reorder enabled) by default */
module_param_named(rx_reorder_disabled, i2400m_rx_reorder_disabled, int, 0644);
MODULE_PARM_DESC(rx_reorder_disabled,
                 "If true, RX reordering will be disabled.");

int i2400m_power_save_disabled; /* 0 (power saving enabled) by default */
module_param_named(power_save_disabled, i2400m_power_save_disabled, int, 0644);
MODULE_PARM_DESC(power_save_disabled,
                 "If true, the driver will not tell the device to enter "
                 "power saving mode when it reports it is ready for it. "
                 "False by default (so the device is told to do power "
                 "saving).");

static char i2400m_debug_params[128];
module_param_string(debug, i2400m_debug_params, sizeof(i2400m_debug_params),
                    0644);
MODULE_PARM_DESC(debug,
                 "String of space-separated NAME:VALUE pairs, where NAMEs "
                 "are the different debug submodules and VALUE are the "
                 "initial debug value to set.");

/**
 * i2400m_queue_work - schedule work on a i2400m's queue
 *
 * @i2400m: device descriptor
 *
 * @fn: function to run to execute work. It gets passed a 'struct
 *     work_struct' that is wrapped in a 'struct i2400m_work'. Once
 *     done, you have to (1) i2400m_put(i2400m_work->i2400m) and then
 *     (2) kfree(i2400m_work).
 *
 * @gfp_flags: GFP flags for memory allocation.
 *
 * @pl: pointer to a payload buffer that you want to pass to the _work
 *     function. Use this to pack (for example) a struct with extra
 *     arguments.
 *
 * @pl_size: size of the payload buffer.
 *
 * We do this quite often, so this just saves typing; allocate a
 * wrapper for a i2400m, get a ref to it, pack arguments and launch
 * the work.
 *
 * A usual workflow is:
 *
 * struct my_work_args {
 *         void *something;
 *         int whatever;
 * };
 * ...
 *
 * struct my_work_args my_args = {
 *         .something = FOO,
 *         .whaetever = BLAH
 * };
 * i2400m_queue_work(i2400m, 1, my_work_function, GFP_KERNEL,
 *                   &args, sizeof(args))
 *
 * And now the work function can unpack the arguments and call the
 * real function (or do the job itself):
 *
 * static
 * void my_work_fn((struct work_struct *ws)
 * {
 *         struct i2400m_work *iw =
 *                 container_of(ws, struct i2400m_work, ws);
 *         struct my_work_args *my_args = (void *) iw->pl;
 *
 *         my_work(iw->i2400m, my_args->something, my_args->whatevert);
 * }
 */
int i2400m_queue_work(struct i2400m *i2400m,
                      void (*fn)(struct work_struct *), gfp_t gfp_flags,
                      const void *pl, size_t pl_size)
{
        int result;
        struct i2400m_work *iw;

        BUG_ON(i2400m->work_queue == NULL);
        result = -ENOMEM;
        iw = kzalloc(sizeof(*iw) + pl_size, gfp_flags);
        if (iw == NULL)
                goto error_kzalloc;
        iw->i2400m = i2400m_get(i2400m);
        memcpy(iw->pl, pl, pl_size);
        INIT_WORK(&iw->ws, fn);
        result = queue_work(i2400m->work_queue, &iw->ws);
error_kzalloc:
        return result;
}
EXPORT_SYMBOL_GPL(i2400m_queue_work);


/*
 * Schedule i2400m's specific work on the system's queue.
 *
 * Used for a few cases where we really need it; otherwise, identical
 * to i2400m_queue_work().
 *
 * Returns < 0 errno code on error, 1 if ok.
 *
 * If it returns zero, something really bad happened, as it means the
 * works struct was already queued, but we have just allocated it, so
 * it should not happen.
 */
int i2400m_schedule_work(struct i2400m *i2400m,
                         void (*fn)(struct work_struct *), gfp_t gfp_flags)
{
        int result;
        struct i2400m_work *iw;

        result = -ENOMEM;
        iw = kzalloc(sizeof(*iw), gfp_flags);
        if (iw == NULL)
                goto error_kzalloc;
        iw->i2400m = i2400m_get(i2400m);
        INIT_WORK(&iw->ws, fn);
        result = schedule_work(&iw->ws);
        if (result == 0)
                result = -ENXIO;
error_kzalloc:
        return result;
}


/*
 * WiMAX stack operation: relay a message from user space
 *
 * @wimax_dev: device descriptor
 * @pipe_name: named pipe the message is for
 * @msg_buf: pointer to the message bytes
 * @msg_len: length of the buffer
 * @genl_info: passed by the generic netlink layer
 *
 * The WiMAX stack will call this function when a message was received
 * from user space.
 *
 * For the i2400m, this is an L3L4 message, as specified in
 * include/linux/wimax/i2400m.h, and thus prefixed with a 'struct
 * i2400m_l3l4_hdr'. Driver (and device) expect the messages to be
 * coded in Little Endian.
 *
 * This function just verifies that the header declaration and the
 * payload are consistent and then deals with it, either forwarding it
 * to the device or procesing it locally.
 *
 * In the i2400m, messages are basically commands that will carry an
 * ack, so we use i2400m_msg_to_dev() and then deliver the ack back to
 * user space. The rx.c code might intercept the response and use it
 * to update the driver's state, but then it will pass it on so it can
 * be relayed back to user space.
 *
 * Note that asynchronous events from the device are processed and
 * sent to user space in rx.c.
 */
static
int i2400m_op_msg_from_user(struct wimax_dev *wimax_dev,
                            const char *pipe_name,
                            const void *msg_buf, size_t msg_len,
                            const struct genl_info *genl_info)
{
        int result;
        struct i2400m *i2400m = wimax_dev_to_i2400m(wimax_dev);
        struct device *dev = i2400m_dev(i2400m);
        struct sk_buff *ack_skb;

        d_fnstart(4, dev, "(wimax_dev %p [i2400m %p] msg_buf %p "
                  "msg_len %zu genl_info %p)\n", wimax_dev, i2400m,
                  msg_buf, msg_len, genl_info);
        ack_skb = i2400m_msg_to_dev(i2400m, msg_buf, msg_len);
        result = PTR_ERR(ack_skb);
        if (IS_ERR(ack_skb))
                goto error_msg_to_dev;
        result = wimax_msg_send(&i2400m->wimax_dev, ack_skb);
error_msg_to_dev:
        d_fnend(4, dev, "(wimax_dev %p [i2400m %p] msg_buf %p msg_len %zu "
                "genl_info %p) = %d\n", wimax_dev, i2400m, msg_buf, msg_len,
                genl_info, result);
        return result;
}


/*
 * Context to wait for a reset to finalize
 */
struct i2400m_reset_ctx {
        struct completion completion;
        int result;
};


/*
 * WiMAX stack operation: reset a device
 *
 * @wimax_dev: device descriptor
 *
 * See the documentation for wimax_reset() and wimax_dev->op_reset for
 * the requirements of this function. The WiMAX stack guarantees
 * serialization on calls to this function.
 *
 * Do a warm reset on the device; if it fails, resort to a cold reset
 * and return -ENODEV. On successful warm reset, we need to block
 * until it is complete.
 *
 * The bus-driver implementation of reset takes care of falling back
 * to cold reset if warm fails.
 */
static
int i2400m_op_reset(struct wimax_dev *wimax_dev)
{
        int result;
        struct i2400m *i2400m = wimax_dev_to_i2400m(wimax_dev);
        struct device *dev = i2400m_dev(i2400m);
        struct i2400m_reset_ctx ctx = {
                .completion = COMPLETION_INITIALIZER_ONSTACK(ctx.completion),
                .result = 0,
        };

        d_fnstart(4, dev, "(wimax_dev %p)\n", wimax_dev);
        mutex_lock(&i2400m->init_mutex);
        i2400m->reset_ctx = &ctx;
        mutex_unlock(&i2400m->init_mutex);
        result = i2400m->bus_reset(i2400m, I2400M_RT_WARM);
        if (result < 0)
                goto out;
        result = wait_for_completion_timeout(&ctx.completion, 4*HZ);
        if (result == 0)
                result = -ETIMEDOUT;
        else if (result > 0)
                result = ctx.result;
        /* if result < 0, pass it on */
        mutex_lock(&i2400m->init_mutex);
        i2400m->reset_ctx = NULL;
        mutex_unlock(&i2400m->init_mutex);
out:
        d_fnend(4, dev, "(wimax_dev %p) = %d\n", wimax_dev, result);
        return result;
}


/*
 * Check the MAC address we got from boot mode is ok
 *
 * @i2400m: device descriptor
 *
 * Returns: 0 if ok, < 0 errno code on error.
 */
static
int i2400m_check_mac_addr(struct i2400m *i2400m)
{
        int result;
        struct device *dev = i2400m_dev(i2400m);
        struct sk_buff *skb;
        const struct i2400m_tlv_detailed_device_info *ddi;
        struct net_device *net_dev = i2400m->wimax_dev.net_dev;
        const unsigned char zeromac[ETH_ALEN] = { 0 };

        d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
        skb = i2400m_get_device_info(i2400m);
        if (IS_ERR(skb)) {
                result = PTR_ERR(skb);
                dev_err(dev, "Cannot verify MAC address, error reading: %d\n",
                        result);
                goto error;
        }
        /* Extract MAC addresss */
        ddi = (void *) skb->data;
        BUILD_BUG_ON(ETH_ALEN != sizeof(ddi->mac_address));
        d_printf(2, dev, "GET DEVICE INFO: mac addr "
                 "%02x:%02x:%02x:%02x:%02x:%02x\n",
                 ddi->mac_address[0], ddi->mac_address[1],
                 ddi->mac_address[2], ddi->mac_address[3],
                 ddi->mac_address[4], ddi->mac_address[5]);
        if (!memcmp(net_dev->perm_addr, ddi->mac_address,
                   sizeof(ddi->mac_address)))
                goto ok;
        dev_warn(dev, "warning: device reports a different MAC address "
                 "to that of boot mode's\n");
        dev_warn(dev, "device reports     %02x:%02x:%02x:%02x:%02x:%02x\n",
                 ddi->mac_address[0], ddi->mac_address[1],
                 ddi->mac_address[2], ddi->mac_address[3],
                 ddi->mac_address[4], ddi->mac_address[5]);
        dev_warn(dev, "boot mode reported %02x:%02x:%02x:%02x:%02x:%02x\n",
                 net_dev->perm_addr[0], net_dev->perm_addr[1],
                 net_dev->perm_addr[2], net_dev->perm_addr[3],
                 net_dev->perm_addr[4], net_dev->perm_addr[5]);
        if (!memcmp(zeromac, ddi->mac_address, sizeof(zeromac)))
                dev_err(dev, "device reports an invalid MAC address, "
                        "not updating\n");
        else {
                dev_warn(dev, "updating MAC address\n");
                net_dev->addr_len = ETH_ALEN;
                memcpy(net_dev->perm_addr, ddi->mac_address, ETH_ALEN);
                memcpy(net_dev->dev_addr, ddi->mac_address, ETH_ALEN);
        }
ok:
        result = 0;
        kfree_skb(skb);
error:
        d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
        return result;
}


/**
 * __i2400m_dev_start - Bring up driver communication with the device
 *
 * @i2400m: device descriptor
 * @flags: boot mode flags
 *
 * Returns: 0 if ok, < 0 errno code on error.
 *
 * Uploads firmware and brings up all the resources needed to be able
 * to communicate with the device.
 *
 * The workqueue has to be setup early, at least before RX handling
 * (it's only real user for now) so it can process reports as they
 * arrive. We also want to destroy it if we retry, to make sure it is
 * flushed...easier like this.
 *
 * TX needs to be setup before the bus-specific code (otherwise on
 * shutdown, the bus-tx code could try to access it).
 */
static
int __i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri flags)
{
        int result;
        struct wimax_dev *wimax_dev = &i2400m->wimax_dev;
        struct net_device *net_dev = wimax_dev->net_dev;
        struct device *dev = i2400m_dev(i2400m);
        int times = i2400m->bus_bm_retries;

        d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
retry:
        result = i2400m_dev_bootstrap(i2400m, flags);
        if (result < 0) {
                dev_err(dev, "cannot bootstrap device: %d\n", result);
                goto error_bootstrap;
        }
        result = i2400m_tx_setup(i2400m);
        if (result < 0)
                goto error_tx_setup;
        result = i2400m_rx_setup(i2400m);
        if (result < 0)
                goto error_rx_setup;
        i2400m->work_queue = create_singlethread_workqueue(wimax_dev->name);
        if (i2400m->work_queue == NULL) {
                result = -ENOMEM;
                dev_err(dev, "cannot create workqueue\n");
                goto error_create_workqueue;
        }
        result = i2400m->bus_dev_start(i2400m);
        if (result < 0)
                goto error_bus_dev_start;
        result = i2400m_firmware_check(i2400m); /* fw versions ok? */
        if (result < 0)
                goto error_fw_check;
        /* At this point is ok to send commands to the device */
        result = i2400m_check_mac_addr(i2400m);
        if (result < 0)
                goto error_check_mac_addr;
        i2400m->ready = 1;
        wimax_state_change(wimax_dev, WIMAX_ST_UNINITIALIZED);
        result = i2400m_dev_initialize(i2400m);
        if (result < 0)
                goto error_dev_initialize;
        /* At this point, reports will come for the device and set it
         * to the right state if it is different than UNINITIALIZED */
        d_fnend(3, dev, "(net_dev %p [i2400m %p]) = %d\n",
                net_dev, i2400m, result);
        return result;

error_dev_initialize:
error_check_mac_addr:
error_fw_check:
        i2400m->bus_dev_stop(i2400m);
error_bus_dev_start:
        destroy_workqueue(i2400m->work_queue);
error_create_workqueue:
        i2400m_rx_release(i2400m);
error_rx_setup:
        i2400m_tx_release(i2400m);
error_tx_setup:
error_bootstrap:
        if (result == -EL3RST && times-- > 0) {
                flags = I2400M_BRI_SOFT|I2400M_BRI_MAC_REINIT;
                goto retry;
        }
        d_fnend(3, dev, "(net_dev %p [i2400m %p]) = %d\n",
                net_dev, i2400m, result);
        return result;
}


static
int i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri bm_flags)
{
        int result;
        mutex_lock(&i2400m->init_mutex);        /* Well, start the device */
        result = __i2400m_dev_start(i2400m, bm_flags);
        if (result >= 0)
                i2400m->updown = 1;
        mutex_unlock(&i2400m->init_mutex);
        return result;
}


/**
 * i2400m_dev_stop - Tear down driver communication with the device
 *
 * @i2400m: device descriptor
 *
 * Returns: 0 if ok, < 0 errno code on error.
 *
 * Releases all the resources allocated to communicate with the
 * device. Note we cannot destroy the workqueue earlier as until RX is
 * fully destroyed, it could still try to schedule jobs.
 */
static
void __i2400m_dev_stop(struct i2400m *i2400m)
{
        struct wimax_dev *wimax_dev = &i2400m->wimax_dev;
        struct device *dev = i2400m_dev(i2400m);

        d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
        wimax_state_change(wimax_dev, __WIMAX_ST_QUIESCING);
        i2400m_dev_shutdown(i2400m);
        i2400m->ready = 0;
        i2400m->bus_dev_stop(i2400m);
        destroy_workqueue(i2400m->work_queue);
        i2400m_rx_release(i2400m);
        i2400m_tx_release(i2400m);
        wimax_state_change(wimax_dev, WIMAX_ST_DOWN);
        d_fnend(3, dev, "(i2400m %p) = 0\n", i2400m);
}


/*
 * Watch out -- we only need to stop if there is a need for it. The
 * device could have reset itself and failed to come up again (see
 * _i2400m_dev_reset_handle()).
 */
static
void i2400m_dev_stop(struct i2400m *i2400m)
{
        mutex_lock(&i2400m->init_mutex);
        if (i2400m->updown) {
                __i2400m_dev_stop(i2400m);
                i2400m->updown = 0;
        }
        mutex_unlock(&i2400m->init_mutex);
}


/*
 * The device has rebooted; fix up the device and the driver
 *
 * Tear down the driver communication with the device, reload the
 * firmware and reinitialize the communication with the device.
 *
 * If someone calls a reset when the device's firmware is down, in
 * theory we won't see it because we are not listening. However, just
 * in case, leave the code to handle it.
 *
 * If there is a reset context, use it; this means someone is waiting
 * for us to tell him when the reset operation is complete and the
 * device is ready to rock again.
 *
 * NOTE: if we are in the process of bringing up or down the
 *       communication with the device [running i2400m_dev_start() or
 *       _stop()], don't do anything, let it fail and handle it.
 *
 * This function is ran always in a thread context
 */
static
void __i2400m_dev_reset_handle(struct work_struct *ws)
{
        int result;
        struct i2400m_work *iw = container_of(ws, struct i2400m_work, ws);
        struct i2400m *i2400m = iw->i2400m;
        struct device *dev = i2400m_dev(i2400m);
        enum wimax_st wimax_state;
        struct i2400m_reset_ctx *ctx = i2400m->reset_ctx;

        d_fnstart(3, dev, "(ws %p i2400m %p)\n", ws, i2400m);
        result = 0;
        if (mutex_trylock(&i2400m->init_mutex) == 0) {
                /* We are still in i2400m_dev_start() [let it fail] or
                 * i2400m_dev_stop() [we are shutting down anyway, so
                 * ignore it] or we are resetting somewhere else. */
                dev_err(dev, "device rebooted\n");
                i2400m_msg_to_dev_cancel_wait(i2400m, -EL3RST);
                complete(&i2400m->msg_completion);
                goto out;
        }
        wimax_state = wimax_state_get(&i2400m->wimax_dev);
        if (wimax_state < WIMAX_ST_UNINITIALIZED) {
                dev_info(dev, "device rebooted: it is down, ignoring\n");
                goto out_unlock;        /* ifconfig up/down wasn't called */
        }
        dev_err(dev, "device rebooted: reinitializing driver\n");
        __i2400m_dev_stop(i2400m);
        i2400m->updown = 0;
        result = __i2400m_dev_start(i2400m,
                                    I2400M_BRI_SOFT | I2400M_BRI_MAC_REINIT);
        if (result < 0) {
                dev_err(dev, "device reboot: cannot start the device: %d\n",
                        result);
                result = i2400m->bus_reset(i2400m, I2400M_RT_BUS);
                if (result >= 0)
                        result = -ENODEV;
        } else
                i2400m->updown = 1;
out_unlock:
        if (i2400m->reset_ctx) {
                ctx->result = result;
                complete(&ctx->completion);
        }
        mutex_unlock(&i2400m->init_mutex);
out:
        i2400m_put(i2400m);
        kfree(iw);
        d_fnend(3, dev, "(ws %p i2400m %p) = void\n", ws, i2400m);
        return;
}


/**
 * i2400m_dev_reset_handle - Handle a device's reset in a thread context
 *
 * Schedule a device reset handling out on a thread context, so it
 * is safe to call from atomic context. We can't use the i2400m's
 * queue as we are going to destroy it and reinitialize it as part of
 * the driver bringup/bringup process.
 *
 * See __i2400m_dev_reset_handle() for details; that takes care of
 * reinitializing the driver to handle the reset, calling into the
 * bus-specific functions ops as needed.
 */
int i2400m_dev_reset_handle(struct i2400m *i2400m)
{
        i2400m->boot_mode = 1;
        wmb();          /* Make sure i2400m_msg_to_dev() sees boot_mode */
        return i2400m_schedule_work(i2400m, __i2400m_dev_reset_handle,
                                    GFP_ATOMIC);
}
EXPORT_SYMBOL_GPL(i2400m_dev_reset_handle);


/**
 * i2400m_bm_buf_alloc - Alloc the command and ack buffers for boot mode
 *
 * Get the buffers needed to deal with boot mode messages.  These
 * buffers need to be allocated before the sdio recieve irq is setup.
 */
int i2400m_bm_buf_alloc(struct i2400m *i2400m)
{
        int result;

        result = -ENOMEM;
        i2400m->bm_cmd_buf = kzalloc(I2400M_BM_CMD_BUF_SIZE, GFP_KERNEL);
        if (i2400m->bm_cmd_buf == NULL)
                goto error_bm_cmd_kzalloc;
        i2400m->bm_ack_buf = kzalloc(I2400M_BM_ACK_BUF_SIZE, GFP_KERNEL);
        if (i2400m->bm_ack_buf == NULL)
                goto error_bm_ack_buf_kzalloc;
        return 0;

error_bm_ack_buf_kzalloc:
        kfree(i2400m->bm_cmd_buf);
error_bm_cmd_kzalloc:
        return result;
}
EXPORT_SYMBOL_GPL(i2400m_bm_buf_alloc);

/**
 * i2400m_bm_buf_free - Free boot mode command and ack buffers.
 *
 * Free the command and ack buffers
 *
 */
void i2400m_bm_buf_free(struct i2400m *i2400m)
{
        kfree(i2400m->bm_ack_buf);
        kfree(i2400m->bm_cmd_buf);
        return;
}
EXPORT_SYMBOL_GPL(i2400m_bm_buf_free
);
/**
 * i2400m_setup - bus-generic setup function for the i2400m device
 *
 * @i2400m: device descriptor (bus-specific parts have been initialized)
 *
 * Returns: 0 if ok, < 0 errno code on error.
 *
 * Initializes the bus-generic parts of the i2400m driver; the
 * bus-specific parts have been initialized, function pointers filled
 * out by the bus-specific probe function.
 *
 * As well, this registers the WiMAX and net device nodes. Once this
 * function returns, the device is operative and has to be ready to
 * receive and send network traffic and WiMAX control operations.
 */
int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
{
        int result = -ENODEV;
        struct device *dev = i2400m_dev(i2400m);
        struct wimax_dev *wimax_dev = &i2400m->wimax_dev;
        struct net_device *net_dev = i2400m->wimax_dev.net_dev;

        d_fnstart(3, dev, "(i2400m %p)\n", i2400m);

        snprintf(wimax_dev->name, sizeof(wimax_dev->name),
                 "i2400m-%s:%s", dev->bus->name, dev_name(dev));

        result = i2400m_bootrom_init(i2400m, bm_flags);
        if (result < 0) {
                dev_err(dev, "read mac addr: bootrom init "
                        "failed: %d\n", result);
                goto error_bootrom_init;
        }
        result = i2400m_read_mac_addr(i2400m);
        if (result < 0)
                goto error_read_mac_addr;
        random_ether_addr(i2400m->src_mac_addr);

        result = register_netdev(net_dev);      /* Okey dokey, bring it up */
        if (result < 0) {
                dev_err(dev, "cannot register i2400m network device: %d\n",
                        result);
                goto error_register_netdev;
        }
        netif_carrier_off(net_dev);

        result = i2400m_dev_start(i2400m, bm_flags);
        if (result < 0)
                goto error_dev_start;

        i2400m->wimax_dev.op_msg_from_user = i2400m_op_msg_from_user;
        i2400m->wimax_dev.op_rfkill_sw_toggle = i2400m_op_rfkill_sw_toggle;
        i2400m->wimax_dev.op_reset = i2400m_op_reset;
        result = wimax_dev_add(&i2400m->wimax_dev, net_dev);
        if (result < 0)
                goto error_wimax_dev_add;
        /* User space needs to do some init stuff */
        wimax_state_change(wimax_dev, WIMAX_ST_UNINITIALIZED);

        /* Now setup all that requires a registered net and wimax device. */
        result = sysfs_create_group(&net_dev->dev.kobj, &i2400m_dev_attr_group);
        if (result < 0) {
                dev_err(dev, "cannot setup i2400m's sysfs: %d\n", result);
                goto error_sysfs_setup;
        }
        result = i2400m_debugfs_add(i2400m);
        if (result < 0) {
                dev_err(dev, "cannot setup i2400m's debugfs: %d\n", result);
                goto error_debugfs_setup;
        }
        d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
        return result;

error_debugfs_setup:
        sysfs_remove_group(&i2400m->wimax_dev.net_dev->dev.kobj,
                           &i2400m_dev_attr_group);
error_sysfs_setup:
        wimax_dev_rm(&i2400m->wimax_dev);
error_wimax_dev_add:
        i2400m_dev_stop(i2400m);
error_dev_start:
        unregister_netdev(net_dev);
error_register_netdev:
error_read_mac_addr:
error_bootrom_init:
        d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
        return result;
}
EXPORT_SYMBOL_GPL(i2400m_setup);


/**
 * i2400m_release - release the bus-generic driver resources
 *
 * Sends a disconnect message and undoes any setup done by i2400m_setup()
 */
void i2400m_release(struct i2400m *i2400m)
{
        struct device *dev = i2400m_dev(i2400m);

        d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
        netif_stop_queue(i2400m->wimax_dev.net_dev);

        i2400m_debugfs_rm(i2400m);
        sysfs_remove_group(&i2400m->wimax_dev.net_dev->dev.kobj,
                           &i2400m_dev_attr_group);
        wimax_dev_rm(&i2400m->wimax_dev);
        i2400m_dev_stop(i2400m);
        unregister_netdev(i2400m->wimax_dev.net_dev);
        kfree(i2400m->bm_ack_buf);
        kfree(i2400m->bm_cmd_buf);
        d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
}
EXPORT_SYMBOL_GPL(i2400m_release);


/*
 * Debug levels control; see debug.h
 */
struct d_level D_LEVEL[] = {
        D_SUBMODULE_DEFINE(control),
        D_SUBMODULE_DEFINE(driver),
        D_SUBMODULE_DEFINE(debugfs),
        D_SUBMODULE_DEFINE(fw),
        D_SUBMODULE_DEFINE(netdev),
        D_SUBMODULE_DEFINE(rfkill),
        D_SUBMODULE_DEFINE(rx),
        D_SUBMODULE_DEFINE(sysfs),
        D_SUBMODULE_DEFINE(tx),
};
size_t D_LEVEL_SIZE = ARRAY_SIZE(D_LEVEL);


static
int __init i2400m_driver_init(void)
{
        d_parse_params(D_LEVEL, D_LEVEL_SIZE, i2400m_debug_params,
                       "i2400m.debug");
        return 0;
}
module_init(i2400m_driver_init);

static
void __exit i2400m_driver_exit(void)
{
        /* for scheds i2400m_dev_reset_handle() */
        flush_scheduled_work();
        return;
}
module_exit(i2400m_driver_exit);

MODULE_AUTHOR("Intel Corporation <linux-wimax@intel.com>");
MODULE_DESCRIPTION("Intel 2400M WiMAX networking bus-generic driver");
MODULE_LICENSE("GPL");