broadcom: Add 57780 support
[safe/jmp/linux-2.6] / drivers / net / ne-h8300.c
1 /* ne-h8300.c: A NE2000 clone on H8/300 driver for linux. */
2 /*
3     original ne.c
4     Written 1992-94 by Donald Becker.
5
6     Copyright 1993 United States Government as represented by the
7     Director, National Security Agency.
8
9     This software may be used and distributed according to the terms
10     of the GNU General Public License, incorporated herein by reference.
11
12     The author may be reached as becker@scyld.com, or C/O
13     Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403
14
15     H8/300 modified
16     Yoshinori Sato <ysato@users.sourceforge.jp>
17 */
18
19 static const char version1[] =
20 "ne-h8300.c:v1.00 2004/04/11 ysato\n";
21
22 #include <linux/module.h>
23 #include <linux/kernel.h>
24 #include <linux/errno.h>
25 #include <linux/init.h>
26 #include <linux/interrupt.h>
27 #include <linux/delay.h>
28 #include <linux/netdevice.h>
29 #include <linux/etherdevice.h>
30 #include <linux/jiffies.h>
31
32 #include <asm/system.h>
33 #include <asm/io.h>
34 #include <asm/irq.h>
35
36 #define EI_SHIFT(x)     (ei_local->reg_offset[x])
37
38 #include "8390.h"
39
40 #define DRV_NAME "ne-h8300"
41
42 /* Some defines that people can play with if so inclined. */
43
44 /* Do we perform extra sanity checks on stuff ? */
45 /* #define NE_SANITY_CHECK */
46
47 /* Do we implement the read before write bugfix ? */
48 /* #define NE_RW_BUGFIX */
49
50 /* Do we have a non std. amount of memory? (in units of 256 byte pages) */
51 /* #define PACKETBUF_MEMSIZE    0x40 */
52
53 /* A zero-terminated list of I/O addresses to be probed at boot. */
54
55 /* ---- No user-serviceable parts below ---- */
56
57 static const char version[] =
58     "8390.c:v1.10cvs 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n";
59
60 #include "lib8390.c"
61
62 #define NE_BASE  (dev->base_addr)
63 #define NE_CMD          0x00
64 #define NE_DATAPORT     (ei_status.word16?0x20:0x10)    /* NatSemi-defined port window offset. */
65 #define NE_RESET        (ei_status.word16?0x3f:0x1f)    /* Issue a read to reset, a write to clear. */
66 #define NE_IO_EXTENT    (ei_status.word16?0x40:0x20)
67
68 #define NESM_START_PG   0x40    /* First page of TX buffer */
69 #define NESM_STOP_PG    0x80    /* Last page +1 of RX ring */
70
71 static int ne_probe1(struct net_device *dev, int ioaddr);
72
73 static int ne_open(struct net_device *dev);
74 static int ne_close(struct net_device *dev);
75
76 static void ne_reset_8390(struct net_device *dev);
77 static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
78                           int ring_page);
79 static void ne_block_input(struct net_device *dev, int count,
80                           struct sk_buff *skb, int ring_offset);
81 static void ne_block_output(struct net_device *dev, const int count,
82                 const unsigned char *buf, const int start_page);
83
84
85 static u32 reg_offset[16];
86
87 static int __init init_reg_offset(struct net_device *dev,unsigned long base_addr)
88 {
89         struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
90         int i;
91         unsigned char bus_width;
92
93         bus_width = *(volatile unsigned char *)ABWCR;
94         bus_width &= 1 << ((base_addr >> 21) & 7);
95
96         for (i = 0; i < ARRAY_SIZE(reg_offset); i++)
97                 if (bus_width == 0)
98                         reg_offset[i] = i * 2 + 1;
99                 else
100                         reg_offset[i] = i;
101
102         ei_local->reg_offset = reg_offset;
103         return 0;
104 }
105
106 static int __initdata h8300_ne_count = 0;
107 #ifdef CONFIG_H8300H_H8MAX
108 static unsigned long __initdata h8300_ne_base[] = { 0x800600 };
109 static int h8300_ne_irq[] = {EXT_IRQ4};
110 #endif
111 #ifdef CONFIG_H8300H_AKI3068NET
112 static unsigned long __initdata h8300_ne_base[] = { 0x200000 };
113 static int h8300_ne_irq[] = {EXT_IRQ5};
114 #endif
115
116 static inline int init_dev(struct net_device *dev)
117 {
118         if (h8300_ne_count < ARRAY_SIZE(h8300_ne_base)) {
119                 dev->base_addr = h8300_ne_base[h8300_ne_count];
120                 dev->irq       = h8300_ne_irq[h8300_ne_count];
121                 h8300_ne_count++;
122                 return 0;
123         } else
124                 return -ENODEV;
125 }
126
127 /*  Probe for various non-shared-memory ethercards.
128
129    NEx000-clone boards have a Station Address PROM (SAPROM) in the packet
130    buffer memory space.  NE2000 clones have 0x57,0x57 in bytes 0x0e,0x0f of
131    the SAPROM, while other supposed NE2000 clones must be detected by their
132    SA prefix.
133
134    Reading the SAPROM from a word-wide card with the 8390 set in byte-wide
135    mode results in doubled values, which can be detected and compensated for.
136
137    The probe is also responsible for initializing the card and filling
138    in the 'dev' and 'ei_status' structures.
139
140    We use the minimum memory size for some ethercard product lines, iff we can't
141    distinguish models.  You can increase the packet buffer size by setting
142    PACKETBUF_MEMSIZE.  Reported Cabletron packet buffer locations are:
143         E1010   starts at 0x100 and ends at 0x2000.
144         E1010-x starts at 0x100 and ends at 0x8000. ("-x" means "more memory")
145         E2010    starts at 0x100 and ends at 0x4000.
146         E2010-x starts at 0x100 and ends at 0xffff.  */
147
148 static int __init do_ne_probe(struct net_device *dev)
149 {
150         unsigned int base_addr = dev->base_addr;
151
152         /* First check any supplied i/o locations. User knows best. <cough> */
153         if (base_addr > 0x1ff)  /* Check a single specified location. */
154                 return ne_probe1(dev, base_addr);
155         else if (base_addr != 0)        /* Don't probe at all. */
156                 return -ENXIO;
157
158         return -ENODEV;
159 }
160
161 static void cleanup_card(struct net_device *dev)
162 {
163         free_irq(dev->irq, dev);
164         release_region(dev->base_addr, NE_IO_EXTENT);
165 }
166
167 #ifndef MODULE
168 struct net_device * __init ne_probe(int unit)
169 {
170         struct net_device *dev = ____alloc_ei_netdev(0);
171         int err;
172
173         if (!dev)
174                 return ERR_PTR(-ENOMEM);
175
176         if (init_dev(dev))
177                 return ERR_PTR(-ENODEV);
178
179         sprintf(dev->name, "eth%d", unit);
180         netdev_boot_setup_check(dev);
181
182         err = init_reg_offset(dev, dev->base_addr);
183         if (err)
184                 goto out;
185
186         err = do_ne_probe(dev);
187         if (err)
188                 goto out;
189         return dev;
190 out:
191         free_netdev(dev);
192         return ERR_PTR(err);
193 }
194 #endif
195
196 static int __init ne_probe1(struct net_device *dev, int ioaddr)
197 {
198         int i;
199         unsigned char SA_prom[16];
200         int wordlength = 2;
201         const char *name = NULL;
202         int start_page, stop_page;
203         int reg0, ret;
204         static unsigned version_printed;
205         struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
206         unsigned char bus_width;
207
208         if (!request_region(ioaddr, NE_IO_EXTENT, DRV_NAME))
209                 return -EBUSY;
210
211         reg0 = inb_p(ioaddr);
212         if (reg0 == 0xFF) {
213                 ret = -ENODEV;
214                 goto err_out;
215         }
216
217         /* Do a preliminary verification that we have a 8390. */
218         {
219                 int regd;
220                 outb_p(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD);
221                 regd = inb_p(ioaddr + EI_SHIFT(0x0d));
222                 outb_p(0xff, ioaddr + EI_SHIFT(0x0d));
223                 outb_p(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD);
224                 inb_p(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */
225                 if (inb_p(ioaddr + EN0_COUNTER0) != 0) {
226                         outb_p(reg0, ioaddr + EI_SHIFT(0));
227                         outb_p(regd, ioaddr + EI_SHIFT(0x0d));  /* Restore the old values. */
228                         ret = -ENODEV;
229                         goto err_out;
230                 }
231         }
232
233         if (ei_debug  &&  version_printed++ == 0)
234                 printk(KERN_INFO "%s", version1);
235
236         printk(KERN_INFO "NE*000 ethercard probe at %08x:", ioaddr);
237
238         /* Read the 16 bytes of station address PROM.
239            We must first initialize registers, similar to NS8390_init(eifdev, 0).
240            We can't reliably read the SAPROM address without this.
241            (I learned the hard way!). */
242         {
243                 struct {unsigned char value, offset; } program_seq[] =
244                 {
245                         {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
246                         {0x48,  EN0_DCFG},      /* Set byte-wide (0x48) access. */
247                         {0x00,  EN0_RCNTLO},    /* Clear the count regs. */
248                         {0x00,  EN0_RCNTHI},
249                         {0x00,  EN0_IMR},       /* Mask completion irq. */
250                         {0xFF,  EN0_ISR},
251                         {E8390_RXOFF, EN0_RXCR},        /* 0x20  Set to monitor */
252                         {E8390_TXOFF, EN0_TXCR},        /* 0x02  and loopback mode. */
253                         {32,    EN0_RCNTLO},
254                         {0x00,  EN0_RCNTHI},
255                         {0x00,  EN0_RSARLO},    /* DMA starting at 0x0000. */
256                         {0x00,  EN0_RSARHI},
257                         {E8390_RREAD+E8390_START, E8390_CMD},
258                 };
259
260                 for (i = 0; i < ARRAY_SIZE(program_seq); i++)
261                         outb_p(program_seq[i].value, ioaddr + program_seq[i].offset);
262
263         }
264         bus_width = *(volatile unsigned char *)ABWCR;
265         bus_width &= 1 << ((ioaddr >> 21) & 7);
266         ei_status.word16 = (bus_width == 0); /* temporary setting */
267         for(i = 0; i < 16 /*sizeof(SA_prom)*/; i++) {
268                 SA_prom[i] = inb_p(ioaddr + NE_DATAPORT);
269                 inb_p(ioaddr + NE_DATAPORT); /* dummy read */
270         }
271
272         start_page = NESM_START_PG;
273         stop_page = NESM_STOP_PG;
274
275         if (bus_width)
276                 wordlength = 1;
277         else
278                 outb_p(0x49, ioaddr + EN0_DCFG);
279
280         /* Set up the rest of the parameters. */
281         name = (wordlength == 2) ? "NE2000" : "NE1000";
282
283         if (! dev->irq) {
284                 printk(" failed to detect IRQ line.\n");
285                 ret = -EAGAIN;
286                 goto err_out;
287         }
288
289         /* Snarf the interrupt now.  There's no point in waiting since we cannot
290            share and the board will usually be enabled. */
291         ret = request_irq(dev->irq, __ei_interrupt, 0, name, dev);
292         if (ret) {
293                 printk (" unable to get IRQ %d (errno=%d).\n", dev->irq, ret);
294                 goto err_out;
295         }
296
297         dev->base_addr = ioaddr;
298
299         for(i = 0; i < ETHER_ADDR_LEN; i++)
300                 dev->dev_addr[i] = SA_prom[i];
301         printk(" %pM\n", dev->dev_addr);
302
303         printk("%s: %s found at %#x, using IRQ %d.\n",
304                 dev->name, name, ioaddr, dev->irq);
305
306         ei_status.name = name;
307         ei_status.tx_start_page = start_page;
308         ei_status.stop_page = stop_page;
309         ei_status.word16 = (wordlength == 2);
310
311         ei_status.rx_start_page = start_page + TX_PAGES;
312 #ifdef PACKETBUF_MEMSIZE
313          /* Allow the packet buffer size to be overridden by know-it-alls. */
314         ei_status.stop_page = ei_status.tx_start_page + PACKETBUF_MEMSIZE;
315 #endif
316
317         ei_status.reset_8390 = &ne_reset_8390;
318         ei_status.block_input = &ne_block_input;
319         ei_status.block_output = &ne_block_output;
320         ei_status.get_8390_hdr = &ne_get_8390_hdr;
321         ei_status.priv = 0;
322         dev->open = &ne_open;
323         dev->stop = &ne_close;
324 #ifdef CONFIG_NET_POLL_CONTROLLER
325         dev->poll_controller = __ei_poll;
326 #endif
327         __NS8390_init(dev, 0);
328
329         ret = register_netdev(dev);
330         if (ret)
331                 goto out_irq;
332         return 0;
333 out_irq:
334         free_irq(dev->irq, dev);
335 err_out:
336         release_region(ioaddr, NE_IO_EXTENT);
337         return ret;
338 }
339
340 static int ne_open(struct net_device *dev)
341 {
342         __ei_open(dev);
343         return 0;
344 }
345
346 static int ne_close(struct net_device *dev)
347 {
348         if (ei_debug > 1)
349                 printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name);
350         __ei_close(dev);
351         return 0;
352 }
353
354 /* Hard reset the card.  This used to pause for the same period that a
355    8390 reset command required, but that shouldn't be necessary. */
356
357 static void ne_reset_8390(struct net_device *dev)
358 {
359         unsigned long reset_start_time = jiffies;
360         struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
361
362         if (ei_debug > 1)
363                 printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies);
364
365         /* DON'T change these to inb_p/outb_p or reset will fail on clones. */
366         outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET);
367
368         ei_status.txing = 0;
369         ei_status.dmaing = 0;
370
371         /* This check _should_not_ be necessary, omit eventually. */
372         while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
373                 if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
374                         printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name);
375                         break;
376                 }
377         outb_p(ENISR_RESET, NE_BASE + EN0_ISR); /* Ack intr. */
378 }
379
380 /* Grab the 8390 specific header. Similar to the block_input routine, but
381    we don't need to be concerned with ring wrap as the header will be at
382    the start of a page, so we optimize accordingly. */
383
384 static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
385 {
386         struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
387         /* This *shouldn't* happen. If it does, it's the last thing you'll see */
388
389         if (ei_status.dmaing)
390         {
391                 printk(KERN_EMERG "%s: DMAing conflict in ne_get_8390_hdr "
392                         "[DMAstat:%d][irqlock:%d].\n",
393                         dev->name, ei_status.dmaing, ei_status.irqlock);
394                 return;
395         }
396
397         ei_status.dmaing |= 0x01;
398         outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD);
399         outb_p(sizeof(struct e8390_pkt_hdr), NE_BASE + EN0_RCNTLO);
400         outb_p(0, NE_BASE + EN0_RCNTHI);
401         outb_p(0, NE_BASE + EN0_RSARLO);                /* On page boundary */
402         outb_p(ring_page, NE_BASE + EN0_RSARHI);
403         outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD);
404
405         if (ei_status.word16) {
406                 int len;
407                 unsigned short *p = (unsigned short *)hdr;
408                 for (len = sizeof(struct e8390_pkt_hdr)>>1; len > 0; len--)
409                         *p++ = inw(NE_BASE + NE_DATAPORT);
410         } else
411                 insb(NE_BASE + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr));
412
413         outb_p(ENISR_RDC, NE_BASE + EN0_ISR);   /* Ack intr. */
414         ei_status.dmaing &= ~0x01;
415
416         le16_to_cpus(&hdr->count);
417 }
418
419 /* Block input and output, similar to the Crynwr packet driver.  If you
420    are porting to a new ethercard, look at the packet driver source for hints.
421    The NEx000 doesn't share the on-board packet memory -- you have to put
422    the packet out through the "remote DMA" dataport using outb. */
423
424 static void ne_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset)
425 {
426         struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
427 #ifdef NE_SANITY_CHECK
428         int xfer_count = count;
429 #endif
430         char *buf = skb->data;
431
432         /* This *shouldn't* happen. If it does, it's the last thing you'll see */
433         if (ei_status.dmaing)
434         {
435                 printk(KERN_EMERG "%s: DMAing conflict in ne_block_input "
436                         "[DMAstat:%d][irqlock:%d].\n",
437                         dev->name, ei_status.dmaing, ei_status.irqlock);
438                 return;
439         }
440         ei_status.dmaing |= 0x01;
441         outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD);
442         outb_p(count & 0xff, NE_BASE + EN0_RCNTLO);
443         outb_p(count >> 8, NE_BASE + EN0_RCNTHI);
444         outb_p(ring_offset & 0xff, NE_BASE + EN0_RSARLO);
445         outb_p(ring_offset >> 8, NE_BASE + EN0_RSARHI);
446         outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD);
447         if (ei_status.word16)
448         {
449                 int len;
450                 unsigned short *p = (unsigned short *)buf;
451                 for (len = count>>1; len > 0; len--)
452                         *p++ = inw(NE_BASE + NE_DATAPORT);
453                 if (count & 0x01)
454                 {
455                         buf[count-1] = inb(NE_BASE + NE_DATAPORT);
456 #ifdef NE_SANITY_CHECK
457                         xfer_count++;
458 #endif
459                 }
460         } else {
461                 insb(NE_BASE + NE_DATAPORT, buf, count);
462         }
463
464 #ifdef NE_SANITY_CHECK
465         /* This was for the ALPHA version only, but enough people have
466            been encountering problems so it is still here.  If you see
467            this message you either 1) have a slightly incompatible clone
468            or 2) have noise/speed problems with your bus. */
469
470         if (ei_debug > 1)
471         {
472                 /* DMA termination address check... */
473                 int addr, tries = 20;
474                 do {
475                         /* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here
476                            -- it's broken for Rx on some cards! */
477                         int high = inb_p(NE_BASE + EN0_RSARHI);
478                         int low = inb_p(NE_BASE + EN0_RSARLO);
479                         addr = (high << 8) + low;
480                         if (((ring_offset + xfer_count) & 0xff) == low)
481                                 break;
482                 } while (--tries > 0);
483                 if (tries <= 0)
484                         printk(KERN_WARNING "%s: RX transfer address mismatch,"
485                                 "%#4.4x (expected) vs. %#4.4x (actual).\n",
486                                 dev->name, ring_offset + xfer_count, addr);
487         }
488 #endif
489         outb_p(ENISR_RDC, NE_BASE + EN0_ISR);   /* Ack intr. */
490         ei_status.dmaing &= ~0x01;
491 }
492
493 static void ne_block_output(struct net_device *dev, int count,
494                 const unsigned char *buf, const int start_page)
495 {
496         struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev);
497         unsigned long dma_start;
498 #ifdef NE_SANITY_CHECK
499         int retries = 0;
500 #endif
501
502         /* Round the count up for word writes.  Do we need to do this?
503            What effect will an odd byte count have on the 8390?
504            I should check someday. */
505
506         if (ei_status.word16 && (count & 0x01))
507                 count++;
508
509         /* This *shouldn't* happen. If it does, it's the last thing you'll see */
510         if (ei_status.dmaing)
511         {
512                 printk(KERN_EMERG "%s: DMAing conflict in ne_block_output."
513                         "[DMAstat:%d][irqlock:%d]\n",
514                         dev->name, ei_status.dmaing, ei_status.irqlock);
515                 return;
516         }
517         ei_status.dmaing |= 0x01;
518         /* We should already be in page 0, but to be safe... */
519         outb_p(E8390_PAGE0+E8390_START+E8390_NODMA, NE_BASE + NE_CMD);
520
521 #ifdef NE_SANITY_CHECK
522 retry:
523 #endif
524
525 #ifdef NE8390_RW_BUGFIX
526         /* Handle the read-before-write bug the same way as the
527            Crynwr packet driver -- the NatSemi method doesn't work.
528            Actually this doesn't always work either, but if you have
529            problems with your NEx000 this is better than nothing! */
530
531         outb_p(0x42, NE_BASE + EN0_RCNTLO);
532         outb_p(0x00, NE_BASE + EN0_RCNTHI);
533         outb_p(0x42, NE_BASE + EN0_RSARLO);
534         outb_p(0x00, NE_BASE + EN0_RSARHI);
535         outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD);
536         /* Make certain that the dummy read has occurred. */
537         udelay(6);
538 #endif
539
540         outb_p(ENISR_RDC, NE_BASE + EN0_ISR);
541
542         /* Now the normal output. */
543         outb_p(count & 0xff, NE_BASE + EN0_RCNTLO);
544         outb_p(count >> 8,   NE_BASE + EN0_RCNTHI);
545         outb_p(0x00, NE_BASE + EN0_RSARLO);
546         outb_p(start_page, NE_BASE + EN0_RSARHI);
547
548         outb_p(E8390_RWRITE+E8390_START, NE_BASE + NE_CMD);
549         if (ei_status.word16) {
550                 int len;
551                 unsigned short *p = (unsigned short *)buf;
552                 for (len = count>>1; len > 0; len--)
553                         outw(*p++, NE_BASE + NE_DATAPORT);
554         } else {
555                 outsb(NE_BASE + NE_DATAPORT, buf, count);
556         }
557
558         dma_start = jiffies;
559
560 #ifdef NE_SANITY_CHECK
561         /* This was for the ALPHA version only, but enough people have
562            been encountering problems so it is still here. */
563
564         if (ei_debug > 1)
565         {
566                 /* DMA termination address check... */
567                 int addr, tries = 20;
568                 do {
569                         int high = inb_p(NE_BASE + EN0_RSARHI);
570                         int low = inb_p(NE_BASE + EN0_RSARLO);
571                         addr = (high << 8) + low;
572                         if ((start_page << 8) + count == addr)
573                                 break;
574                 } while (--tries > 0);
575
576                 if (tries <= 0)
577                 {
578                         printk(KERN_WARNING "%s: Tx packet transfer address mismatch,"
579                                 "%#4.4x (expected) vs. %#4.4x (actual).\n",
580                                 dev->name, (start_page << 8) + count, addr);
581                         if (retries++ == 0)
582                                 goto retry;
583                 }
584         }
585 #endif
586
587         while ((inb_p(NE_BASE + EN0_ISR) & ENISR_RDC) == 0)
588                 if (time_after(jiffies, dma_start + 2*HZ/100)) {                /* 20ms */
589                         printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
590                         ne_reset_8390(dev);
591                         __NS8390_init(dev,1);
592                         break;
593                 }
594
595         outb_p(ENISR_RDC, NE_BASE + EN0_ISR);   /* Ack intr. */
596         ei_status.dmaing &= ~0x01;
597         return;
598 }
599
600
601 #ifdef MODULE
602 #define MAX_NE_CARDS    1       /* Max number of NE cards per module */
603 static struct net_device *dev_ne[MAX_NE_CARDS];
604 static int io[MAX_NE_CARDS];
605 static int irq[MAX_NE_CARDS];
606 static int bad[MAX_NE_CARDS];   /* 0xbad = bad sig or no reset ack */
607
608 module_param_array(io, int, NULL, 0);
609 module_param_array(irq, int, NULL, 0);
610 module_param_array(bad, int, NULL, 0);
611 MODULE_PARM_DESC(io, "I/O base address(es)");
612 MODULE_PARM_DESC(irq, "IRQ number(s)");
613 MODULE_DESCRIPTION("H8/300 NE2000 Ethernet driver");
614 MODULE_LICENSE("GPL");
615
616 /* This is set up so that no ISA autoprobe takes place. We can't guarantee
617 that the ne2k probe is the last 8390 based probe to take place (as it
618 is at boot) and so the probe will get confused by any other 8390 cards.
619 ISA device autoprobes on a running machine are not recommended anyway. */
620
621 int init_module(void)
622 {
623         int this_dev, found = 0;
624         int err;
625
626         for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
627                 struct net_device *dev = ____alloc_ei_netdev(0);
628                 if (!dev)
629                         break;
630                 if (io[this_dev]) {
631                         dev->irq = irq[this_dev];
632                         dev->mem_end = bad[this_dev];
633                         dev->base_addr = io[this_dev];
634                 } else {
635                         dev->base_addr = h8300_ne_base[this_dev];
636                         dev->irq = h8300_ne_irq[this_dev];
637                 }
638                 err = init_reg_offset(dev, dev->base_addr);
639                 if (!err) {
640                         if (do_ne_probe(dev) == 0) {
641                                 dev_ne[found++] = dev;
642                                 continue;
643                         }
644                 }
645                 free_netdev(dev);
646                 if (found)
647                         break;
648                 if (io[this_dev] != 0)
649                         printk(KERN_WARNING "ne.c: No NE*000 card found at i/o = %#x\n", dev->base_addr);
650                 else
651                         printk(KERN_NOTICE "ne.c: You must supply \"io=0xNNN\" value(s) for ISA cards.\n");
652                 return -ENXIO;
653         }
654         if (found)
655                 return 0;
656         return -ENODEV;
657 }
658
659 void cleanup_module(void)
660 {
661         int this_dev;
662
663         for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
664                 struct net_device *dev = dev_ne[this_dev];
665                 if (dev) {
666                         unregister_netdev(dev);
667                         cleanup_card(dev);
668                         free_netdev(dev);
669                 }
670         }
671 }
672 #endif /* MODULE */