1 /*******************************************************************************
3 Intel PRO/1000 Linux driver
4 Copyright(c) 1999 - 2009 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 Linux NICS <linux.nics@intel.com>
24 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
25 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
27 *******************************************************************************/
30 * 82562G 10/100 Network Connection
31 * 82562G-2 10/100 Network Connection
32 * 82562GT 10/100 Network Connection
33 * 82562GT-2 10/100 Network Connection
34 * 82562V 10/100 Network Connection
35 * 82562V-2 10/100 Network Connection
36 * 82566DC-2 Gigabit Network Connection
37 * 82566DC Gigabit Network Connection
38 * 82566DM-2 Gigabit Network Connection
39 * 82566DM Gigabit Network Connection
40 * 82566MC Gigabit Network Connection
41 * 82566MM Gigabit Network Connection
42 * 82567LM Gigabit Network Connection
43 * 82567LF Gigabit Network Connection
44 * 82567V Gigabit Network Connection
45 * 82567LM-2 Gigabit Network Connection
46 * 82567LF-2 Gigabit Network Connection
47 * 82567V-2 Gigabit Network Connection
48 * 82567LF-3 Gigabit Network Connection
49 * 82567LM-3 Gigabit Network Connection
50 * 82567LM-4 Gigabit Network Connection
51 * 82577LM Gigabit Network Connection
52 * 82577LC Gigabit Network Connection
53 * 82578DM Gigabit Network Connection
54 * 82578DC Gigabit Network Connection
59 #define ICH_FLASH_GFPREG 0x0000
60 #define ICH_FLASH_HSFSTS 0x0004
61 #define ICH_FLASH_HSFCTL 0x0006
62 #define ICH_FLASH_FADDR 0x0008
63 #define ICH_FLASH_FDATA0 0x0010
64 #define ICH_FLASH_PR0 0x0074
66 #define ICH_FLASH_READ_COMMAND_TIMEOUT 500
67 #define ICH_FLASH_WRITE_COMMAND_TIMEOUT 500
68 #define ICH_FLASH_ERASE_COMMAND_TIMEOUT 3000000
69 #define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
70 #define ICH_FLASH_CYCLE_REPEAT_COUNT 10
72 #define ICH_CYCLE_READ 0
73 #define ICH_CYCLE_WRITE 2
74 #define ICH_CYCLE_ERASE 3
76 #define FLASH_GFPREG_BASE_MASK 0x1FFF
77 #define FLASH_SECTOR_ADDR_SHIFT 12
79 #define ICH_FLASH_SEG_SIZE_256 256
80 #define ICH_FLASH_SEG_SIZE_4K 4096
81 #define ICH_FLASH_SEG_SIZE_8K 8192
82 #define ICH_FLASH_SEG_SIZE_64K 65536
85 #define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */
86 /* FW established a valid mode */
87 #define E1000_ICH_FWSM_FW_VALID 0x00008000
89 #define E1000_ICH_MNG_IAMT_MODE 0x2
91 #define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \
92 (ID_LED_DEF1_OFF2 << 8) | \
93 (ID_LED_DEF1_ON2 << 4) | \
96 #define E1000_ICH_NVM_SIG_WORD 0x13
97 #define E1000_ICH_NVM_SIG_MASK 0xC000
98 #define E1000_ICH_NVM_VALID_SIG_MASK 0xC0
99 #define E1000_ICH_NVM_SIG_VALUE 0x80
101 #define E1000_ICH8_LAN_INIT_TIMEOUT 1500
103 #define E1000_FEXTNVM_SW_CONFIG 1
104 #define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M :/ */
106 #define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL
108 #define E1000_ICH_RAR_ENTRIES 7
110 #define PHY_PAGE_SHIFT 5
111 #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
112 ((reg) & MAX_PHY_REG_ADDRESS))
113 #define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */
114 #define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */
116 #define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002
117 #define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
118 #define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200
120 #define HV_LED_CONFIG PHY_REG(768, 30) /* LED Configuration */
122 #define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in milliseconds */
124 /* SMBus Address Phy Register */
125 #define HV_SMB_ADDR PHY_REG(768, 26)
126 #define HV_SMB_ADDR_PEC_EN 0x0200
127 #define HV_SMB_ADDR_VALID 0x0080
129 /* Strapping Option Register - RO */
130 #define E1000_STRAP 0x0000C
131 #define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
132 #define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
134 /* OEM Bits Phy Register */
135 #define HV_OEM_BITS PHY_REG(768, 25)
136 #define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
137 #define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
138 #define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
140 #define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
141 #define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */
143 /* KMRN Mode Control */
144 #define HV_KMRN_MODE_CTRL PHY_REG(769, 16)
145 #define HV_KMRN_MDIO_SLOW 0x0400
147 /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
148 /* Offset 04h HSFSTS */
149 union ich8_hws_flash_status {
151 u16 flcdone :1; /* bit 0 Flash Cycle Done */
152 u16 flcerr :1; /* bit 1 Flash Cycle Error */
153 u16 dael :1; /* bit 2 Direct Access error Log */
154 u16 berasesz :2; /* bit 4:3 Sector Erase Size */
155 u16 flcinprog :1; /* bit 5 flash cycle in Progress */
156 u16 reserved1 :2; /* bit 13:6 Reserved */
157 u16 reserved2 :6; /* bit 13:6 Reserved */
158 u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */
159 u16 flockdn :1; /* bit 15 Flash Config Lock-Down */
164 /* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */
165 /* Offset 06h FLCTL */
166 union ich8_hws_flash_ctrl {
167 struct ich8_hsflctl {
168 u16 flcgo :1; /* 0 Flash Cycle Go */
169 u16 flcycle :2; /* 2:1 Flash Cycle */
170 u16 reserved :5; /* 7:3 Reserved */
171 u16 fldbcount :2; /* 9:8 Flash Data Byte Count */
172 u16 flockdn :6; /* 15:10 Reserved */
177 /* ICH Flash Region Access Permissions */
178 union ich8_hws_flash_regacc {
180 u32 grra :8; /* 0:7 GbE region Read Access */
181 u32 grwa :8; /* 8:15 GbE region Write Access */
182 u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */
183 u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */
188 /* ICH Flash Protected Region */
189 union ich8_flash_protected_range {
191 u32 base:13; /* 0:12 Protected Range Base */
192 u32 reserved1:2; /* 13:14 Reserved */
193 u32 rpe:1; /* 15 Read Protection Enable */
194 u32 limit:13; /* 16:28 Protected Range Limit */
195 u32 reserved2:2; /* 29:30 Reserved */
196 u32 wpe:1; /* 31 Write Protection Enable */
201 static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw);
202 static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw);
203 static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw);
204 static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank);
205 static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw,
206 u32 offset, u8 byte);
207 static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
209 static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset,
211 static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
213 static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw);
214 static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw);
215 static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw);
216 static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw);
217 static s32 e1000_led_on_ich8lan(struct e1000_hw *hw);
218 static s32 e1000_led_off_ich8lan(struct e1000_hw *hw);
219 static s32 e1000_id_led_init_pchlan(struct e1000_hw *hw);
220 static s32 e1000_setup_led_pchlan(struct e1000_hw *hw);
221 static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw);
222 static s32 e1000_led_on_pchlan(struct e1000_hw *hw);
223 static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
224 static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
225 static void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw);
226 static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
227 static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
228 static s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw);
230 static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
232 return readw(hw->flash_address + reg);
235 static inline u32 __er32flash(struct e1000_hw *hw, unsigned long reg)
237 return readl(hw->flash_address + reg);
240 static inline void __ew16flash(struct e1000_hw *hw, unsigned long reg, u16 val)
242 writew(val, hw->flash_address + reg);
245 static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val)
247 writel(val, hw->flash_address + reg);
250 #define er16flash(reg) __er16flash(hw, (reg))
251 #define er32flash(reg) __er32flash(hw, (reg))
252 #define ew16flash(reg,val) __ew16flash(hw, (reg), (val))
253 #define ew32flash(reg,val) __ew32flash(hw, (reg), (val))
256 * e1000_init_phy_params_pchlan - Initialize PHY function pointers
257 * @hw: pointer to the HW structure
259 * Initialize family-specific PHY parameters and function pointers.
261 static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
263 struct e1000_phy_info *phy = &hw->phy;
268 phy->reset_delay_us = 100;
270 phy->ops.read_reg = e1000_read_phy_reg_hv;
271 phy->ops.read_reg_locked = e1000_read_phy_reg_hv_locked;
272 phy->ops.set_d0_lplu_state = e1000_set_lplu_state_pchlan;
273 phy->ops.set_d3_lplu_state = e1000_set_lplu_state_pchlan;
274 phy->ops.write_reg = e1000_write_phy_reg_hv;
275 phy->ops.write_reg_locked = e1000_write_phy_reg_hv_locked;
276 phy->ops.power_up = e1000_power_up_phy_copper;
277 phy->ops.power_down = e1000_power_down_phy_copper_ich8lan;
278 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
280 if (!(er32(FWSM) & E1000_ICH_FWSM_FW_VALID)) {
282 * The MAC-PHY interconnect may still be in SMBus mode
283 * after Sx->S0. Toggle the LANPHYPC Value bit to force
284 * the interconnect to PCIe mode, but only if there is no
285 * firmware present otherwise firmware will have done it.
288 ctrl |= E1000_CTRL_LANPHYPC_OVERRIDE;
289 ctrl &= ~E1000_CTRL_LANPHYPC_VALUE;
292 ctrl &= ~E1000_CTRL_LANPHYPC_OVERRIDE;
298 * Reset the PHY before any acccess to it. Doing so, ensures that
299 * the PHY is in a known good state before we read/write PHY registers.
300 * The generic reset is sufficient here, because we haven't determined
303 ret_val = e1000e_phy_hw_reset_generic(hw);
307 phy->id = e1000_phy_unknown;
308 ret_val = e1000e_get_phy_id(hw);
311 if ((phy->id == 0) || (phy->id == PHY_REVISION_MASK)) {
313 * In case the PHY needs to be in mdio slow mode (eg. 82577),
314 * set slow mode and try to get the PHY id again.
316 ret_val = e1000_set_mdio_slow_mode_hv(hw);
319 ret_val = e1000e_get_phy_id(hw);
323 phy->type = e1000e_get_phy_type_from_id(phy->id);
326 case e1000_phy_82577:
327 phy->ops.check_polarity = e1000_check_polarity_82577;
328 phy->ops.force_speed_duplex =
329 e1000_phy_force_speed_duplex_82577;
330 phy->ops.get_cable_length = e1000_get_cable_length_82577;
331 phy->ops.get_info = e1000_get_phy_info_82577;
332 phy->ops.commit = e1000e_phy_sw_reset;
333 case e1000_phy_82578:
334 phy->ops.check_polarity = e1000_check_polarity_m88;
335 phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_m88;
336 phy->ops.get_cable_length = e1000e_get_cable_length_m88;
337 phy->ops.get_info = e1000e_get_phy_info_m88;
340 ret_val = -E1000_ERR_PHY;
349 * e1000_init_phy_params_ich8lan - Initialize PHY function pointers
350 * @hw: pointer to the HW structure
352 * Initialize family-specific PHY parameters and function pointers.
354 static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw)
356 struct e1000_phy_info *phy = &hw->phy;
361 phy->reset_delay_us = 100;
363 phy->ops.power_up = e1000_power_up_phy_copper;
364 phy->ops.power_down = e1000_power_down_phy_copper_ich8lan;
367 * We may need to do this twice - once for IGP and if that fails,
368 * we'll set BM func pointers and try again
370 ret_val = e1000e_determine_phy_address(hw);
372 phy->ops.write_reg = e1000e_write_phy_reg_bm;
373 phy->ops.read_reg = e1000e_read_phy_reg_bm;
374 ret_val = e1000e_determine_phy_address(hw);
376 e_dbg("Cannot determine PHY addr. Erroring out\n");
382 while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) &&
385 ret_val = e1000e_get_phy_id(hw);
392 case IGP03E1000_E_PHY_ID:
393 phy->type = e1000_phy_igp_3;
394 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
395 phy->ops.read_reg_locked = e1000e_read_phy_reg_igp_locked;
396 phy->ops.write_reg_locked = e1000e_write_phy_reg_igp_locked;
397 phy->ops.get_info = e1000e_get_phy_info_igp;
398 phy->ops.check_polarity = e1000_check_polarity_igp;
399 phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_igp;
402 case IFE_PLUS_E_PHY_ID:
404 phy->type = e1000_phy_ife;
405 phy->autoneg_mask = E1000_ALL_NOT_GIG;
406 phy->ops.get_info = e1000_get_phy_info_ife;
407 phy->ops.check_polarity = e1000_check_polarity_ife;
408 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_ife;
410 case BME1000_E_PHY_ID:
411 phy->type = e1000_phy_bm;
412 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
413 phy->ops.read_reg = e1000e_read_phy_reg_bm;
414 phy->ops.write_reg = e1000e_write_phy_reg_bm;
415 phy->ops.commit = e1000e_phy_sw_reset;
416 phy->ops.get_info = e1000e_get_phy_info_m88;
417 phy->ops.check_polarity = e1000_check_polarity_m88;
418 phy->ops.force_speed_duplex = e1000e_phy_force_speed_duplex_m88;
421 return -E1000_ERR_PHY;
429 * e1000_init_nvm_params_ich8lan - Initialize NVM function pointers
430 * @hw: pointer to the HW structure
432 * Initialize family-specific NVM parameters and function
435 static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw)
437 struct e1000_nvm_info *nvm = &hw->nvm;
438 struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
439 u32 gfpreg, sector_base_addr, sector_end_addr;
442 /* Can't read flash registers if the register set isn't mapped. */
443 if (!hw->flash_address) {
444 e_dbg("ERROR: Flash registers not mapped\n");
445 return -E1000_ERR_CONFIG;
448 nvm->type = e1000_nvm_flash_sw;
450 gfpreg = er32flash(ICH_FLASH_GFPREG);
453 * sector_X_addr is a "sector"-aligned address (4096 bytes)
454 * Add 1 to sector_end_addr since this sector is included in
457 sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK;
458 sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1;
460 /* flash_base_addr is byte-aligned */
461 nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT;
464 * find total size of the NVM, then cut in half since the total
465 * size represents two separate NVM banks.
467 nvm->flash_bank_size = (sector_end_addr - sector_base_addr)
468 << FLASH_SECTOR_ADDR_SHIFT;
469 nvm->flash_bank_size /= 2;
470 /* Adjust to word count */
471 nvm->flash_bank_size /= sizeof(u16);
473 nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS;
475 /* Clear shadow ram */
476 for (i = 0; i < nvm->word_size; i++) {
477 dev_spec->shadow_ram[i].modified = false;
478 dev_spec->shadow_ram[i].value = 0xFFFF;
485 * e1000_init_mac_params_ich8lan - Initialize MAC function pointers
486 * @hw: pointer to the HW structure
488 * Initialize family-specific MAC parameters and function
491 static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter)
493 struct e1000_hw *hw = &adapter->hw;
494 struct e1000_mac_info *mac = &hw->mac;
496 /* Set media type function pointer */
497 hw->phy.media_type = e1000_media_type_copper;
499 /* Set mta register count */
500 mac->mta_reg_count = 32;
501 /* Set rar entry count */
502 mac->rar_entry_count = E1000_ICH_RAR_ENTRIES;
503 if (mac->type == e1000_ich8lan)
504 mac->rar_entry_count--;
505 /* Set if manageability features are enabled. */
506 mac->arc_subsystem_valid = true;
507 /* Adaptive IFS supported */
508 mac->adaptive_ifs = true;
516 mac->ops.id_led_init = e1000e_id_led_init;
518 mac->ops.setup_led = e1000e_setup_led_generic;
520 mac->ops.cleanup_led = e1000_cleanup_led_ich8lan;
521 /* turn on/off LED */
522 mac->ops.led_on = e1000_led_on_ich8lan;
523 mac->ops.led_off = e1000_led_off_ich8lan;
527 mac->ops.id_led_init = e1000_id_led_init_pchlan;
529 mac->ops.setup_led = e1000_setup_led_pchlan;
531 mac->ops.cleanup_led = e1000_cleanup_led_pchlan;
532 /* turn on/off LED */
533 mac->ops.led_on = e1000_led_on_pchlan;
534 mac->ops.led_off = e1000_led_off_pchlan;
540 /* Enable PCS Lock-loss workaround for ICH8 */
541 if (mac->type == e1000_ich8lan)
542 e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, true);
548 * e1000_check_for_copper_link_ich8lan - Check for link (Copper)
549 * @hw: pointer to the HW structure
551 * Checks to see of the link status of the hardware has changed. If a
552 * change in link status has been detected, then we read the PHY registers
553 * to get the current speed/duplex if link exists.
555 static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
557 struct e1000_mac_info *mac = &hw->mac;
562 * We only want to go out to the PHY registers to see if Auto-Neg
563 * has completed and/or if our link status has changed. The
564 * get_link_status flag is set upon receiving a Link Status
565 * Change or Rx Sequence Error interrupt.
567 if (!mac->get_link_status) {
573 * First we want to see if the MII Status Register reports
574 * link. If so, then we want to get the current speed/duplex
577 ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
581 if (hw->mac.type == e1000_pchlan) {
582 ret_val = e1000_k1_gig_workaround_hv(hw, link);
588 goto out; /* No link detected */
590 mac->get_link_status = false;
592 if (hw->phy.type == e1000_phy_82578) {
593 ret_val = e1000_link_stall_workaround_hv(hw);
599 * Check if there was DownShift, must be checked
600 * immediately after link-up
602 e1000e_check_downshift(hw);
605 * If we are forcing speed/duplex, then we simply return since
606 * we have already determined whether we have link or not.
609 ret_val = -E1000_ERR_CONFIG;
614 * Auto-Neg is enabled. Auto Speed Detection takes care
615 * of MAC speed/duplex configuration. So we only need to
616 * configure Collision Distance in the MAC.
618 e1000e_config_collision_dist(hw);
621 * Configure Flow Control now that Auto-Neg has completed.
622 * First, we need to restore the desired flow control
623 * settings because we may have had to re-autoneg with a
624 * different link partner.
626 ret_val = e1000e_config_fc_after_link_up(hw);
628 e_dbg("Error configuring flow control\n");
634 static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter)
636 struct e1000_hw *hw = &adapter->hw;
639 rc = e1000_init_mac_params_ich8lan(adapter);
643 rc = e1000_init_nvm_params_ich8lan(hw);
647 if (hw->mac.type == e1000_pchlan)
648 rc = e1000_init_phy_params_pchlan(hw);
650 rc = e1000_init_phy_params_ich8lan(hw);
654 if (adapter->hw.phy.type == e1000_phy_ife) {
655 adapter->flags &= ~FLAG_HAS_JUMBO_FRAMES;
656 adapter->max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN;
659 if ((adapter->hw.mac.type == e1000_ich8lan) &&
660 (adapter->hw.phy.type == e1000_phy_igp_3))
661 adapter->flags |= FLAG_LSC_GIG_SPEED_DROP;
666 static DEFINE_MUTEX(nvm_mutex);
669 * e1000_acquire_nvm_ich8lan - Acquire NVM mutex
670 * @hw: pointer to the HW structure
672 * Acquires the mutex for performing NVM operations.
674 static s32 e1000_acquire_nvm_ich8lan(struct e1000_hw *hw)
676 mutex_lock(&nvm_mutex);
682 * e1000_release_nvm_ich8lan - Release NVM mutex
683 * @hw: pointer to the HW structure
685 * Releases the mutex used while performing NVM operations.
687 static void e1000_release_nvm_ich8lan(struct e1000_hw *hw)
689 mutex_unlock(&nvm_mutex);
694 static DEFINE_MUTEX(swflag_mutex);
697 * e1000_acquire_swflag_ich8lan - Acquire software control flag
698 * @hw: pointer to the HW structure
700 * Acquires the software control flag for performing PHY and select
703 static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
705 u32 extcnf_ctrl, timeout = PHY_CFG_TIMEOUT;
708 mutex_lock(&swflag_mutex);
711 extcnf_ctrl = er32(EXTCNF_CTRL);
712 if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG))
720 e_dbg("SW/FW/HW has locked the resource for too long.\n");
721 ret_val = -E1000_ERR_CONFIG;
725 timeout = SW_FLAG_TIMEOUT;
727 extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
728 ew32(EXTCNF_CTRL, extcnf_ctrl);
731 extcnf_ctrl = er32(EXTCNF_CTRL);
732 if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
740 e_dbg("Failed to acquire the semaphore.\n");
741 extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
742 ew32(EXTCNF_CTRL, extcnf_ctrl);
743 ret_val = -E1000_ERR_CONFIG;
749 mutex_unlock(&swflag_mutex);
755 * e1000_release_swflag_ich8lan - Release software control flag
756 * @hw: pointer to the HW structure
758 * Releases the software control flag for performing PHY and select
761 static void e1000_release_swflag_ich8lan(struct e1000_hw *hw)
765 extcnf_ctrl = er32(EXTCNF_CTRL);
766 extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
767 ew32(EXTCNF_CTRL, extcnf_ctrl);
769 mutex_unlock(&swflag_mutex);
775 * e1000_check_mng_mode_ich8lan - Checks management mode
776 * @hw: pointer to the HW structure
778 * This checks if the adapter has manageability enabled.
779 * This is a function pointer entry point only called by read/write
780 * routines for the PHY and NVM parts.
782 static bool e1000_check_mng_mode_ich8lan(struct e1000_hw *hw)
788 return (fwsm & E1000_FWSM_MODE_MASK) ==
789 (E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT);
793 * e1000_check_reset_block_ich8lan - Check if PHY reset is blocked
794 * @hw: pointer to the HW structure
796 * Checks if firmware is blocking the reset of the PHY.
797 * This is a function pointer entry point only called by
800 static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw)
806 return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? 0 : E1000_BLK_PHY_RESET;
810 * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration
811 * @hw: pointer to the HW structure
813 * SW should configure the LCD from the NVM extended configuration region
814 * as a workaround for certain parts.
816 static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw)
818 struct e1000_adapter *adapter = hw->adapter;
819 struct e1000_phy_info *phy = &hw->phy;
820 u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask;
822 u16 word_addr, reg_data, reg_addr, phy_page = 0;
824 if (!(hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) &&
825 !(hw->mac.type == e1000_pchlan))
828 ret_val = hw->phy.ops.acquire(hw);
833 * Initialize the PHY from the NVM on ICH platforms. This
834 * is needed due to an issue where the NVM configuration is
835 * not properly autoloaded after power transitions.
836 * Therefore, after each PHY reset, we will load the
837 * configuration data out of the NVM manually.
839 if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
840 (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M) ||
841 (hw->mac.type == e1000_pchlan))
842 sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
844 sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
846 data = er32(FEXTNVM);
847 if (!(data & sw_cfg_mask))
850 /* Wait for basic configuration completes before proceeding */
851 e1000_lan_init_done_ich8lan(hw);
854 * Make sure HW does not configure LCD from PHY
855 * extended configuration before SW configuration
857 data = er32(EXTCNF_CTRL);
858 if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
861 cnf_size = er32(EXTCNF_SIZE);
862 cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
863 cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
867 cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
868 cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
870 if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) &&
871 (hw->mac.type == e1000_pchlan)) {
873 * HW configures the SMBus address and LEDs when the
874 * OEM and LCD Write Enable bits are set in the NVM.
875 * When both NVM bits are cleared, SW will configure
879 data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
880 reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
881 reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
882 ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
888 ret_val = e1000_write_phy_reg_hv_locked(hw, HV_LED_CONFIG,
894 /* Configure LCD from extended configuration region. */
896 /* cnf_base_addr is in DWORD */
897 word_addr = (u16)(cnf_base_addr << 1);
899 for (i = 0; i < cnf_size; i++) {
900 ret_val = e1000_read_nvm(hw, (word_addr + i * 2), 1,
905 ret_val = e1000_read_nvm(hw, (word_addr + i * 2 + 1),
910 /* Save off the PHY page for future writes. */
911 if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
916 reg_addr &= PHY_REG_MASK;
917 reg_addr |= phy_page;
919 ret_val = phy->ops.write_reg_locked(hw, (u32)reg_addr,
926 hw->phy.ops.release(hw);
931 * e1000_k1_gig_workaround_hv - K1 Si workaround
932 * @hw: pointer to the HW structure
933 * @link: link up bool flag
935 * If K1 is enabled for 1Gbps, the MAC might stall when transitioning
936 * from a lower speed. This workaround disables K1 whenever link is at 1Gig
937 * If link is down, the function will restore the default K1 setting located
940 static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link)
944 bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled;
946 if (hw->mac.type != e1000_pchlan)
949 /* Wrap the whole flow with the sw flag */
950 ret_val = hw->phy.ops.acquire(hw);
954 /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */
956 if (hw->phy.type == e1000_phy_82578) {
957 ret_val = hw->phy.ops.read_reg_locked(hw, BM_CS_STATUS,
962 status_reg &= BM_CS_STATUS_LINK_UP |
963 BM_CS_STATUS_RESOLVED |
964 BM_CS_STATUS_SPEED_MASK;
966 if (status_reg == (BM_CS_STATUS_LINK_UP |
967 BM_CS_STATUS_RESOLVED |
968 BM_CS_STATUS_SPEED_1000))
972 if (hw->phy.type == e1000_phy_82577) {
973 ret_val = hw->phy.ops.read_reg_locked(hw, HV_M_STATUS,
978 status_reg &= HV_M_STATUS_LINK_UP |
979 HV_M_STATUS_AUTONEG_COMPLETE |
980 HV_M_STATUS_SPEED_MASK;
982 if (status_reg == (HV_M_STATUS_LINK_UP |
983 HV_M_STATUS_AUTONEG_COMPLETE |
984 HV_M_STATUS_SPEED_1000))
988 /* Link stall fix for link up */
989 ret_val = hw->phy.ops.write_reg_locked(hw, PHY_REG(770, 19),
995 /* Link stall fix for link down */
996 ret_val = hw->phy.ops.write_reg_locked(hw, PHY_REG(770, 19),
1002 ret_val = e1000_configure_k1_ich8lan(hw, k1_enable);
1005 hw->phy.ops.release(hw);
1011 * e1000_configure_k1_ich8lan - Configure K1 power state
1012 * @hw: pointer to the HW structure
1013 * @enable: K1 state to configure
1015 * Configure the K1 power state based on the provided parameter.
1016 * Assumes semaphore already acquired.
1018 * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
1020 s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
1028 ret_val = e1000e_read_kmrn_reg_locked(hw,
1029 E1000_KMRNCTRLSTA_K1_CONFIG,
1035 kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE;
1037 kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE;
1039 ret_val = e1000e_write_kmrn_reg_locked(hw,
1040 E1000_KMRNCTRLSTA_K1_CONFIG,
1046 ctrl_ext = er32(CTRL_EXT);
1047 ctrl_reg = er32(CTRL);
1049 reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
1050 reg |= E1000_CTRL_FRCSPD;
1053 ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS);
1055 ew32(CTRL, ctrl_reg);
1056 ew32(CTRL_EXT, ctrl_ext);
1064 * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration
1065 * @hw: pointer to the HW structure
1066 * @d0_state: boolean if entering d0 or d3 device state
1068 * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are
1069 * collectively called OEM bits. The OEM Write Enable bit and SW Config bit
1070 * in NVM determines whether HW should configure LPLU and Gbe Disable.
1072 static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
1078 if (hw->mac.type != e1000_pchlan)
1081 ret_val = hw->phy.ops.acquire(hw);
1085 mac_reg = er32(EXTCNF_CTRL);
1086 if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)
1089 mac_reg = er32(FEXTNVM);
1090 if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M))
1093 mac_reg = er32(PHY_CTRL);
1095 ret_val = hw->phy.ops.read_reg_locked(hw, HV_OEM_BITS, &oem_reg);
1099 oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU);
1102 if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE)
1103 oem_reg |= HV_OEM_BITS_GBE_DIS;
1105 if (mac_reg & E1000_PHY_CTRL_D0A_LPLU)
1106 oem_reg |= HV_OEM_BITS_LPLU;
1108 if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE)
1109 oem_reg |= HV_OEM_BITS_GBE_DIS;
1111 if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU)
1112 oem_reg |= HV_OEM_BITS_LPLU;
1114 /* Restart auto-neg to activate the bits */
1115 if (!e1000_check_reset_block(hw))
1116 oem_reg |= HV_OEM_BITS_RESTART_AN;
1117 ret_val = hw->phy.ops.write_reg_locked(hw, HV_OEM_BITS, oem_reg);
1120 hw->phy.ops.release(hw);
1127 * e1000_set_mdio_slow_mode_hv - Set slow MDIO access mode
1128 * @hw: pointer to the HW structure
1130 static s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw)
1135 ret_val = e1e_rphy(hw, HV_KMRN_MODE_CTRL, &data);
1139 data |= HV_KMRN_MDIO_SLOW;
1141 ret_val = e1e_wphy(hw, HV_KMRN_MODE_CTRL, data);
1147 * e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
1148 * done after every PHY reset.
1150 static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
1155 if (hw->mac.type != e1000_pchlan)
1158 /* Set MDIO slow mode before any other MDIO access */
1159 if (hw->phy.type == e1000_phy_82577) {
1160 ret_val = e1000_set_mdio_slow_mode_hv(hw);
1165 if (((hw->phy.type == e1000_phy_82577) &&
1166 ((hw->phy.revision == 1) || (hw->phy.revision == 2))) ||
1167 ((hw->phy.type == e1000_phy_82578) && (hw->phy.revision == 1))) {
1168 /* Disable generation of early preamble */
1169 ret_val = e1e_wphy(hw, PHY_REG(769, 25), 0x4431);
1173 /* Preamble tuning for SSC */
1174 ret_val = e1e_wphy(hw, PHY_REG(770, 16), 0xA204);
1179 if (hw->phy.type == e1000_phy_82578) {
1181 * Return registers to default by doing a soft reset then
1182 * writing 0x3140 to the control register.
1184 if (hw->phy.revision < 2) {
1185 e1000e_phy_sw_reset(hw);
1186 ret_val = e1e_wphy(hw, PHY_CONTROL, 0x3140);
1191 ret_val = hw->phy.ops.acquire(hw);
1196 ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
1197 hw->phy.ops.release(hw);
1202 * Configure the K1 Si workaround during phy reset assuming there is
1203 * link so that it disables K1 if link is in 1Gbps.
1205 ret_val = e1000_k1_gig_workaround_hv(hw, true);
1209 /* Workaround for link disconnects on a busy hub in half duplex */
1210 ret_val = hw->phy.ops.acquire(hw);
1213 ret_val = hw->phy.ops.read_reg_locked(hw,
1214 PHY_REG(BM_PORT_CTRL_PAGE, 17),
1218 ret_val = hw->phy.ops.write_reg_locked(hw,
1219 PHY_REG(BM_PORT_CTRL_PAGE, 17),
1222 hw->phy.ops.release(hw);
1228 * e1000_lan_init_done_ich8lan - Check for PHY config completion
1229 * @hw: pointer to the HW structure
1231 * Check the appropriate indication the MAC has finished configuring the
1232 * PHY after a software reset.
1234 static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw)
1236 u32 data, loop = E1000_ICH8_LAN_INIT_TIMEOUT;
1238 /* Wait for basic configuration completes before proceeding */
1240 data = er32(STATUS);
1241 data &= E1000_STATUS_LAN_INIT_DONE;
1243 } while ((!data) && --loop);
1246 * If basic configuration is incomplete before the above loop
1247 * count reaches 0, loading the configuration from NVM will
1248 * leave the PHY in a bad state possibly resulting in no link.
1251 e_dbg("LAN_INIT_DONE not set, increase timeout\n");
1253 /* Clear the Init Done bit for the next init event */
1254 data = er32(STATUS);
1255 data &= ~E1000_STATUS_LAN_INIT_DONE;
1260 * e1000_phy_hw_reset_ich8lan - Performs a PHY reset
1261 * @hw: pointer to the HW structure
1264 * This is a function pointer entry point called by drivers
1265 * or other shared routines.
1267 static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
1272 ret_val = e1000e_phy_hw_reset_generic(hw);
1276 /* Allow time for h/w to get to a quiescent state after reset */
1279 /* Perform any necessary post-reset workarounds */
1280 if (hw->mac.type == e1000_pchlan) {
1281 ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
1286 /* Dummy read to clear the phy wakeup bit after lcd reset */
1287 if (hw->mac.type == e1000_pchlan)
1288 e1e_rphy(hw, BM_WUC, ®);
1290 /* Configure the LCD with the extended configuration region in NVM */
1291 ret_val = e1000_sw_lcd_config_ich8lan(hw);
1295 /* Configure the LCD with the OEM bits in NVM */
1296 if (hw->mac.type == e1000_pchlan)
1297 ret_val = e1000_oem_bits_config_ich8lan(hw, true);
1304 * e1000_set_lplu_state_pchlan - Set Low Power Link Up state
1305 * @hw: pointer to the HW structure
1306 * @active: true to enable LPLU, false to disable
1308 * Sets the LPLU state according to the active flag. For PCH, if OEM write
1309 * bit are disabled in the NVM, writing the LPLU bits in the MAC will not set
1310 * the phy speed. This function will manually set the LPLU bit and restart
1311 * auto-neg as hw would do. D3 and D0 LPLU will call the same function
1312 * since it configures the same bit.
1314 static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active)
1319 ret_val = e1e_rphy(hw, HV_OEM_BITS, &oem_reg);
1324 oem_reg |= HV_OEM_BITS_LPLU;
1326 oem_reg &= ~HV_OEM_BITS_LPLU;
1328 oem_reg |= HV_OEM_BITS_RESTART_AN;
1329 ret_val = e1e_wphy(hw, HV_OEM_BITS, oem_reg);
1336 * e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state
1337 * @hw: pointer to the HW structure
1338 * @active: true to enable LPLU, false to disable
1340 * Sets the LPLU D0 state according to the active flag. When
1341 * activating LPLU this function also disables smart speed
1342 * and vice versa. LPLU will not be activated unless the
1343 * device autonegotiation advertisement meets standards of
1344 * either 10 or 10/100 or 10/100/1000 at all duplexes.
1345 * This is a function pointer entry point only called by
1346 * PHY setup routines.
1348 static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
1350 struct e1000_phy_info *phy = &hw->phy;
1355 if (phy->type == e1000_phy_ife)
1358 phy_ctrl = er32(PHY_CTRL);
1361 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
1362 ew32(PHY_CTRL, phy_ctrl);
1364 if (phy->type != e1000_phy_igp_3)
1368 * Call gig speed drop workaround on LPLU before accessing
1371 if (hw->mac.type == e1000_ich8lan)
1372 e1000e_gig_downshift_workaround_ich8lan(hw);
1374 /* When LPLU is enabled, we should disable SmartSpeed */
1375 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
1376 data &= ~IGP01E1000_PSCFR_SMART_SPEED;
1377 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
1381 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
1382 ew32(PHY_CTRL, phy_ctrl);
1384 if (phy->type != e1000_phy_igp_3)
1388 * LPLU and SmartSpeed are mutually exclusive. LPLU is used
1389 * during Dx states where the power conservation is most
1390 * important. During driver activity we should enable
1391 * SmartSpeed, so performance is maintained.
1393 if (phy->smart_speed == e1000_smart_speed_on) {
1394 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1399 data |= IGP01E1000_PSCFR_SMART_SPEED;
1400 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1404 } else if (phy->smart_speed == e1000_smart_speed_off) {
1405 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1410 data &= ~IGP01E1000_PSCFR_SMART_SPEED;
1411 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1422 * e1000_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state
1423 * @hw: pointer to the HW structure
1424 * @active: true to enable LPLU, false to disable
1426 * Sets the LPLU D3 state according to the active flag. When
1427 * activating LPLU this function also disables smart speed
1428 * and vice versa. LPLU will not be activated unless the
1429 * device autonegotiation advertisement meets standards of
1430 * either 10 or 10/100 or 10/100/1000 at all duplexes.
1431 * This is a function pointer entry point only called by
1432 * PHY setup routines.
1434 static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
1436 struct e1000_phy_info *phy = &hw->phy;
1441 phy_ctrl = er32(PHY_CTRL);
1444 phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
1445 ew32(PHY_CTRL, phy_ctrl);
1447 if (phy->type != e1000_phy_igp_3)
1451 * LPLU and SmartSpeed are mutually exclusive. LPLU is used
1452 * during Dx states where the power conservation is most
1453 * important. During driver activity we should enable
1454 * SmartSpeed, so performance is maintained.
1456 if (phy->smart_speed == e1000_smart_speed_on) {
1457 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1462 data |= IGP01E1000_PSCFR_SMART_SPEED;
1463 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1467 } else if (phy->smart_speed == e1000_smart_speed_off) {
1468 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1473 data &= ~IGP01E1000_PSCFR_SMART_SPEED;
1474 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
1479 } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
1480 (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
1481 (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
1482 phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
1483 ew32(PHY_CTRL, phy_ctrl);
1485 if (phy->type != e1000_phy_igp_3)
1489 * Call gig speed drop workaround on LPLU before accessing
1492 if (hw->mac.type == e1000_ich8lan)
1493 e1000e_gig_downshift_workaround_ich8lan(hw);
1495 /* When LPLU is enabled, we should disable SmartSpeed */
1496 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
1500 data &= ~IGP01E1000_PSCFR_SMART_SPEED;
1501 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
1508 * e1000_valid_nvm_bank_detect_ich8lan - finds out the valid bank 0 or 1
1509 * @hw: pointer to the HW structure
1510 * @bank: pointer to the variable that returns the active bank
1512 * Reads signature byte from the NVM using the flash access registers.
1513 * Word 0x13 bits 15:14 = 10b indicate a valid signature for that bank.
1515 static s32 e1000_valid_nvm_bank_detect_ich8lan(struct e1000_hw *hw, u32 *bank)
1518 struct e1000_nvm_info *nvm = &hw->nvm;
1519 u32 bank1_offset = nvm->flash_bank_size * sizeof(u16);
1520 u32 act_offset = E1000_ICH_NVM_SIG_WORD * 2 + 1;
1524 switch (hw->mac.type) {
1528 if ((eecd & E1000_EECD_SEC1VAL_VALID_MASK) ==
1529 E1000_EECD_SEC1VAL_VALID_MASK) {
1530 if (eecd & E1000_EECD_SEC1VAL)
1537 e_dbg("Unable to determine valid NVM bank via EEC - "
1538 "reading flash signature\n");
1541 /* set bank to 0 in case flash read fails */
1545 ret_val = e1000_read_flash_byte_ich8lan(hw, act_offset,
1549 if ((sig_byte & E1000_ICH_NVM_VALID_SIG_MASK) ==
1550 E1000_ICH_NVM_SIG_VALUE) {
1556 ret_val = e1000_read_flash_byte_ich8lan(hw, act_offset +
1561 if ((sig_byte & E1000_ICH_NVM_VALID_SIG_MASK) ==
1562 E1000_ICH_NVM_SIG_VALUE) {
1567 e_dbg("ERROR: No valid NVM bank present\n");
1568 return -E1000_ERR_NVM;
1575 * e1000_read_nvm_ich8lan - Read word(s) from the NVM
1576 * @hw: pointer to the HW structure
1577 * @offset: The offset (in bytes) of the word(s) to read.
1578 * @words: Size of data to read in words
1579 * @data: Pointer to the word(s) to read at offset.
1581 * Reads a word(s) from the NVM using the flash access registers.
1583 static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
1586 struct e1000_nvm_info *nvm = &hw->nvm;
1587 struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
1593 if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
1595 e_dbg("nvm parameter(s) out of bounds\n");
1596 ret_val = -E1000_ERR_NVM;
1600 nvm->ops.acquire(hw);
1602 ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
1604 e_dbg("Could not detect valid bank, assuming bank 0\n");
1608 act_offset = (bank) ? nvm->flash_bank_size : 0;
1609 act_offset += offset;
1612 for (i = 0; i < words; i++) {
1613 if ((dev_spec->shadow_ram) &&
1614 (dev_spec->shadow_ram[offset+i].modified)) {
1615 data[i] = dev_spec->shadow_ram[offset+i].value;
1617 ret_val = e1000_read_flash_word_ich8lan(hw,
1626 nvm->ops.release(hw);
1630 e_dbg("NVM read error: %d\n", ret_val);
1636 * e1000_flash_cycle_init_ich8lan - Initialize flash
1637 * @hw: pointer to the HW structure
1639 * This function does initial flash setup so that a new read/write/erase cycle
1642 static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw)
1644 union ich8_hws_flash_status hsfsts;
1645 s32 ret_val = -E1000_ERR_NVM;
1648 hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
1650 /* Check if the flash descriptor is valid */
1651 if (hsfsts.hsf_status.fldesvalid == 0) {
1652 e_dbg("Flash descriptor invalid. "
1653 "SW Sequencing must be used.\n");
1654 return -E1000_ERR_NVM;
1657 /* Clear FCERR and DAEL in hw status by writing 1 */
1658 hsfsts.hsf_status.flcerr = 1;
1659 hsfsts.hsf_status.dael = 1;
1661 ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
1664 * Either we should have a hardware SPI cycle in progress
1665 * bit to check against, in order to start a new cycle or
1666 * FDONE bit should be changed in the hardware so that it
1667 * is 1 after hardware reset, which can then be used as an
1668 * indication whether a cycle is in progress or has been
1672 if (hsfsts.hsf_status.flcinprog == 0) {
1674 * There is no cycle running at present,
1675 * so we can start a cycle.
1676 * Begin by setting Flash Cycle Done.
1678 hsfsts.hsf_status.flcdone = 1;
1679 ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
1683 * Otherwise poll for sometime so the current
1684 * cycle has a chance to end before giving up.
1686 for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) {
1687 hsfsts.regval = __er16flash(hw, ICH_FLASH_HSFSTS);
1688 if (hsfsts.hsf_status.flcinprog == 0) {
1696 * Successful in waiting for previous cycle to timeout,
1697 * now set the Flash Cycle Done.
1699 hsfsts.hsf_status.flcdone = 1;
1700 ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
1702 e_dbg("Flash controller busy, cannot get access\n");
1710 * e1000_flash_cycle_ich8lan - Starts flash cycle (read/write/erase)
1711 * @hw: pointer to the HW structure
1712 * @timeout: maximum time to wait for completion
1714 * This function starts a flash cycle and waits for its completion.
1716 static s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout)
1718 union ich8_hws_flash_ctrl hsflctl;
1719 union ich8_hws_flash_status hsfsts;
1720 s32 ret_val = -E1000_ERR_NVM;
1723 /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
1724 hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
1725 hsflctl.hsf_ctrl.flcgo = 1;
1726 ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
1728 /* wait till FDONE bit is set to 1 */
1730 hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
1731 if (hsfsts.hsf_status.flcdone == 1)
1734 } while (i++ < timeout);
1736 if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0)
1743 * e1000_read_flash_word_ich8lan - Read word from flash
1744 * @hw: pointer to the HW structure
1745 * @offset: offset to data location
1746 * @data: pointer to the location for storing the data
1748 * Reads the flash word at offset into data. Offset is converted
1749 * to bytes before read.
1751 static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset,
1754 /* Must convert offset into bytes. */
1757 return e1000_read_flash_data_ich8lan(hw, offset, 2, data);
1761 * e1000_read_flash_byte_ich8lan - Read byte from flash
1762 * @hw: pointer to the HW structure
1763 * @offset: The offset of the byte to read.
1764 * @data: Pointer to a byte to store the value read.
1766 * Reads a single byte from the NVM using the flash access registers.
1768 static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
1774 ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word);
1784 * e1000_read_flash_data_ich8lan - Read byte or word from NVM
1785 * @hw: pointer to the HW structure
1786 * @offset: The offset (in bytes) of the byte or word to read.
1787 * @size: Size of data to read, 1=byte 2=word
1788 * @data: Pointer to the word to store the value read.
1790 * Reads a byte or word from the NVM using the flash access registers.
1792 static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
1795 union ich8_hws_flash_status hsfsts;
1796 union ich8_hws_flash_ctrl hsflctl;
1797 u32 flash_linear_addr;
1799 s32 ret_val = -E1000_ERR_NVM;
1802 if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK)
1803 return -E1000_ERR_NVM;
1805 flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) +
1806 hw->nvm.flash_base_addr;
1811 ret_val = e1000_flash_cycle_init_ich8lan(hw);
1815 hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
1816 /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
1817 hsflctl.hsf_ctrl.fldbcount = size - 1;
1818 hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ;
1819 ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
1821 ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
1823 ret_val = e1000_flash_cycle_ich8lan(hw,
1824 ICH_FLASH_READ_COMMAND_TIMEOUT);
1827 * Check if FCERR is set to 1, if set to 1, clear it
1828 * and try the whole sequence a few more times, else
1829 * read in (shift in) the Flash Data0, the order is
1830 * least significant byte first msb to lsb
1833 flash_data = er32flash(ICH_FLASH_FDATA0);
1835 *data = (u8)(flash_data & 0x000000FF);
1836 } else if (size == 2) {
1837 *data = (u16)(flash_data & 0x0000FFFF);
1842 * If we've gotten here, then things are probably
1843 * completely hosed, but if the error condition is
1844 * detected, it won't hurt to give it another try...
1845 * ICH_FLASH_CYCLE_REPEAT_COUNT times.
1847 hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
1848 if (hsfsts.hsf_status.flcerr == 1) {
1849 /* Repeat for some time before giving up. */
1851 } else if (hsfsts.hsf_status.flcdone == 0) {
1852 e_dbg("Timeout error - flash cycle "
1853 "did not complete.\n");
1857 } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
1863 * e1000_write_nvm_ich8lan - Write word(s) to the NVM
1864 * @hw: pointer to the HW structure
1865 * @offset: The offset (in bytes) of the word(s) to write.
1866 * @words: Size of data to write in words
1867 * @data: Pointer to the word(s) to write at offset.
1869 * Writes a byte or word to the NVM using the flash access registers.
1871 static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
1874 struct e1000_nvm_info *nvm = &hw->nvm;
1875 struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
1878 if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
1880 e_dbg("nvm parameter(s) out of bounds\n");
1881 return -E1000_ERR_NVM;
1884 nvm->ops.acquire(hw);
1886 for (i = 0; i < words; i++) {
1887 dev_spec->shadow_ram[offset+i].modified = true;
1888 dev_spec->shadow_ram[offset+i].value = data[i];
1891 nvm->ops.release(hw);
1897 * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM
1898 * @hw: pointer to the HW structure
1900 * The NVM checksum is updated by calling the generic update_nvm_checksum,
1901 * which writes the checksum to the shadow ram. The changes in the shadow
1902 * ram are then committed to the EEPROM by processing each bank at a time
1903 * checking for the modified bit and writing only the pending changes.
1904 * After a successful commit, the shadow ram is cleared and is ready for
1907 static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
1909 struct e1000_nvm_info *nvm = &hw->nvm;
1910 struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
1911 u32 i, act_offset, new_bank_offset, old_bank_offset, bank;
1915 ret_val = e1000e_update_nvm_checksum_generic(hw);
1919 if (nvm->type != e1000_nvm_flash_sw)
1922 nvm->ops.acquire(hw);
1925 * We're writing to the opposite bank so if we're on bank 1,
1926 * write to bank 0 etc. We also need to erase the segment that
1927 * is going to be written
1929 ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
1931 e_dbg("Could not detect valid bank, assuming bank 0\n");
1936 new_bank_offset = nvm->flash_bank_size;
1937 old_bank_offset = 0;
1938 ret_val = e1000_erase_flash_bank_ich8lan(hw, 1);
1942 old_bank_offset = nvm->flash_bank_size;
1943 new_bank_offset = 0;
1944 ret_val = e1000_erase_flash_bank_ich8lan(hw, 0);
1949 for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
1951 * Determine whether to write the value stored
1952 * in the other NVM bank or a modified value stored
1955 if (dev_spec->shadow_ram[i].modified) {
1956 data = dev_spec->shadow_ram[i].value;
1958 ret_val = e1000_read_flash_word_ich8lan(hw, i +
1966 * If the word is 0x13, then make sure the signature bits
1967 * (15:14) are 11b until the commit has completed.
1968 * This will allow us to write 10b which indicates the
1969 * signature is valid. We want to do this after the write
1970 * has completed so that we don't mark the segment valid
1971 * while the write is still in progress
1973 if (i == E1000_ICH_NVM_SIG_WORD)
1974 data |= E1000_ICH_NVM_SIG_MASK;
1976 /* Convert offset to bytes. */
1977 act_offset = (i + new_bank_offset) << 1;
1980 /* Write the bytes to the new bank. */
1981 ret_val = e1000_retry_write_flash_byte_ich8lan(hw,
1988 ret_val = e1000_retry_write_flash_byte_ich8lan(hw,
1996 * Don't bother writing the segment valid bits if sector
1997 * programming failed.
2000 /* Possibly read-only, see e1000e_write_protect_nvm_ich8lan() */
2001 e_dbg("Flash commit failed.\n");
2006 * Finally validate the new segment by setting bit 15:14
2007 * to 10b in word 0x13 , this can be done without an
2008 * erase as well since these bits are 11 to start with
2009 * and we need to change bit 14 to 0b
2011 act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD;
2012 ret_val = e1000_read_flash_word_ich8lan(hw, act_offset, &data);
2017 ret_val = e1000_retry_write_flash_byte_ich8lan(hw,
2024 * And invalidate the previously valid segment by setting
2025 * its signature word (0x13) high_byte to 0b. This can be
2026 * done without an erase because flash erase sets all bits
2027 * to 1's. We can write 1's to 0's without an erase
2029 act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1;
2030 ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0);
2034 /* Great! Everything worked, we can now clear the cached entries. */
2035 for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
2036 dev_spec->shadow_ram[i].modified = false;
2037 dev_spec->shadow_ram[i].value = 0xFFFF;
2041 nvm->ops.release(hw);
2044 * Reload the EEPROM, or else modifications will not appear
2045 * until after the next adapter reset.
2048 e1000e_reload_nvm(hw);
2054 e_dbg("NVM update error: %d\n", ret_val);
2060 * e1000_validate_nvm_checksum_ich8lan - Validate EEPROM checksum
2061 * @hw: pointer to the HW structure
2063 * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19.
2064 * If the bit is 0, that the EEPROM had been modified, but the checksum was not
2065 * calculated, in which case we need to calculate the checksum and set bit 6.
2067 static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw)
2073 * Read 0x19 and check bit 6. If this bit is 0, the checksum
2074 * needs to be fixed. This bit is an indication that the NVM
2075 * was prepared by OEM software and did not calculate the
2076 * checksum...a likely scenario.
2078 ret_val = e1000_read_nvm(hw, 0x19, 1, &data);
2082 if ((data & 0x40) == 0) {
2084 ret_val = e1000_write_nvm(hw, 0x19, 1, &data);
2087 ret_val = e1000e_update_nvm_checksum(hw);
2092 return e1000e_validate_nvm_checksum_generic(hw);
2096 * e1000e_write_protect_nvm_ich8lan - Make the NVM read-only
2097 * @hw: pointer to the HW structure
2099 * To prevent malicious write/erase of the NVM, set it to be read-only
2100 * so that the hardware ignores all write/erase cycles of the NVM via
2101 * the flash control registers. The shadow-ram copy of the NVM will
2102 * still be updated, however any updates to this copy will not stick
2103 * across driver reloads.
2105 void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw)
2107 struct e1000_nvm_info *nvm = &hw->nvm;
2108 union ich8_flash_protected_range pr0;
2109 union ich8_hws_flash_status hsfsts;
2112 nvm->ops.acquire(hw);
2114 gfpreg = er32flash(ICH_FLASH_GFPREG);
2116 /* Write-protect GbE Sector of NVM */
2117 pr0.regval = er32flash(ICH_FLASH_PR0);
2118 pr0.range.base = gfpreg & FLASH_GFPREG_BASE_MASK;
2119 pr0.range.limit = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK);
2120 pr0.range.wpe = true;
2121 ew32flash(ICH_FLASH_PR0, pr0.regval);
2124 * Lock down a subset of GbE Flash Control Registers, e.g.
2125 * PR0 to prevent the write-protection from being lifted.
2126 * Once FLOCKDN is set, the registers protected by it cannot
2127 * be written until FLOCKDN is cleared by a hardware reset.
2129 hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
2130 hsfsts.hsf_status.flockdn = true;
2131 ew32flash(ICH_FLASH_HSFSTS, hsfsts.regval);
2133 nvm->ops.release(hw);
2137 * e1000_write_flash_data_ich8lan - Writes bytes to the NVM
2138 * @hw: pointer to the HW structure
2139 * @offset: The offset (in bytes) of the byte/word to read.
2140 * @size: Size of data to read, 1=byte 2=word
2141 * @data: The byte(s) to write to the NVM.
2143 * Writes one/two bytes to the NVM using the flash access registers.
2145 static s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
2148 union ich8_hws_flash_status hsfsts;
2149 union ich8_hws_flash_ctrl hsflctl;
2150 u32 flash_linear_addr;
2155 if (size < 1 || size > 2 || data > size * 0xff ||
2156 offset > ICH_FLASH_LINEAR_ADDR_MASK)
2157 return -E1000_ERR_NVM;
2159 flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) +
2160 hw->nvm.flash_base_addr;
2165 ret_val = e1000_flash_cycle_init_ich8lan(hw);
2169 hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
2170 /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
2171 hsflctl.hsf_ctrl.fldbcount = size -1;
2172 hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE;
2173 ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
2175 ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
2178 flash_data = (u32)data & 0x00FF;
2180 flash_data = (u32)data;
2182 ew32flash(ICH_FLASH_FDATA0, flash_data);
2185 * check if FCERR is set to 1 , if set to 1, clear it
2186 * and try the whole sequence a few more times else done
2188 ret_val = e1000_flash_cycle_ich8lan(hw,
2189 ICH_FLASH_WRITE_COMMAND_TIMEOUT);
2194 * If we're here, then things are most likely
2195 * completely hosed, but if the error condition
2196 * is detected, it won't hurt to give it another
2197 * try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
2199 hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
2200 if (hsfsts.hsf_status.flcerr == 1)
2201 /* Repeat for some time before giving up. */
2203 if (hsfsts.hsf_status.flcdone == 0) {
2204 e_dbg("Timeout error - flash cycle "
2205 "did not complete.");
2208 } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
2214 * e1000_write_flash_byte_ich8lan - Write a single byte to NVM
2215 * @hw: pointer to the HW structure
2216 * @offset: The index of the byte to read.
2217 * @data: The byte to write to the NVM.
2219 * Writes a single byte to the NVM using the flash access registers.
2221 static s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
2224 u16 word = (u16)data;
2226 return e1000_write_flash_data_ich8lan(hw, offset, 1, word);
2230 * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM
2231 * @hw: pointer to the HW structure
2232 * @offset: The offset of the byte to write.
2233 * @byte: The byte to write to the NVM.
2235 * Writes a single byte to the NVM using the flash access registers.
2236 * Goes through a retry algorithm before giving up.
2238 static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw,
2239 u32 offset, u8 byte)
2242 u16 program_retries;
2244 ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte);
2248 for (program_retries = 0; program_retries < 100; program_retries++) {
2249 e_dbg("Retrying Byte %2.2X at offset %u\n", byte, offset);
2251 ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte);
2255 if (program_retries == 100)
2256 return -E1000_ERR_NVM;
2262 * e1000_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM
2263 * @hw: pointer to the HW structure
2264 * @bank: 0 for first bank, 1 for second bank, etc.
2266 * Erases the bank specified. Each bank is a 4k block. Banks are 0 based.
2267 * bank N is 4096 * N + flash_reg_addr.
2269 static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank)
2271 struct e1000_nvm_info *nvm = &hw->nvm;
2272 union ich8_hws_flash_status hsfsts;
2273 union ich8_hws_flash_ctrl hsflctl;
2274 u32 flash_linear_addr;
2275 /* bank size is in 16bit words - adjust to bytes */
2276 u32 flash_bank_size = nvm->flash_bank_size * 2;
2279 s32 j, iteration, sector_size;
2281 hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
2284 * Determine HW Sector size: Read BERASE bits of hw flash status
2286 * 00: The Hw sector is 256 bytes, hence we need to erase 16
2287 * consecutive sectors. The start index for the nth Hw sector
2288 * can be calculated as = bank * 4096 + n * 256
2289 * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector.
2290 * The start index for the nth Hw sector can be calculated
2292 * 10: The Hw sector is 8K bytes, nth sector = bank * 8192
2293 * (ich9 only, otherwise error condition)
2294 * 11: The Hw sector is 64K bytes, nth sector = bank * 65536
2296 switch (hsfsts.hsf_status.berasesz) {
2298 /* Hw sector size 256 */
2299 sector_size = ICH_FLASH_SEG_SIZE_256;
2300 iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256;
2303 sector_size = ICH_FLASH_SEG_SIZE_4K;
2307 sector_size = ICH_FLASH_SEG_SIZE_8K;
2311 sector_size = ICH_FLASH_SEG_SIZE_64K;
2315 return -E1000_ERR_NVM;
2318 /* Start with the base address, then add the sector offset. */
2319 flash_linear_addr = hw->nvm.flash_base_addr;
2320 flash_linear_addr += (bank) ? flash_bank_size : 0;
2322 for (j = 0; j < iteration ; j++) {
2325 ret_val = e1000_flash_cycle_init_ich8lan(hw);
2330 * Write a value 11 (block Erase) in Flash
2331 * Cycle field in hw flash control
2333 hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
2334 hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE;
2335 ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
2338 * Write the last 24 bits of an index within the
2339 * block into Flash Linear address field in Flash
2342 flash_linear_addr += (j * sector_size);
2343 ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
2345 ret_val = e1000_flash_cycle_ich8lan(hw,
2346 ICH_FLASH_ERASE_COMMAND_TIMEOUT);
2351 * Check if FCERR is set to 1. If 1,
2352 * clear it and try the whole sequence
2353 * a few more times else Done
2355 hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
2356 if (hsfsts.hsf_status.flcerr == 1)
2357 /* repeat for some time before giving up */
2359 else if (hsfsts.hsf_status.flcdone == 0)
2361 } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT);
2368 * e1000_valid_led_default_ich8lan - Set the default LED settings
2369 * @hw: pointer to the HW structure
2370 * @data: Pointer to the LED settings
2372 * Reads the LED default settings from the NVM to data. If the NVM LED
2373 * settings is all 0's or F's, set the LED default to a valid LED default
2376 static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data)
2380 ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
2382 e_dbg("NVM Read Error\n");
2386 if (*data == ID_LED_RESERVED_0000 ||
2387 *data == ID_LED_RESERVED_FFFF)
2388 *data = ID_LED_DEFAULT_ICH8LAN;
2394 * e1000_id_led_init_pchlan - store LED configurations
2395 * @hw: pointer to the HW structure
2397 * PCH does not control LEDs via the LEDCTL register, rather it uses
2398 * the PHY LED configuration register.
2400 * PCH also does not have an "always on" or "always off" mode which
2401 * complicates the ID feature. Instead of using the "on" mode to indicate
2402 * in ledctl_mode2 the LEDs to use for ID (see e1000e_id_led_init()),
2403 * use "link_up" mode. The LEDs will still ID on request if there is no
2404 * link based on logic in e1000_led_[on|off]_pchlan().
2406 static s32 e1000_id_led_init_pchlan(struct e1000_hw *hw)
2408 struct e1000_mac_info *mac = &hw->mac;
2410 const u32 ledctl_on = E1000_LEDCTL_MODE_LINK_UP;
2411 const u32 ledctl_off = E1000_LEDCTL_MODE_LINK_UP | E1000_PHY_LED0_IVRT;
2412 u16 data, i, temp, shift;
2414 /* Get default ID LED modes */
2415 ret_val = hw->nvm.ops.valid_led_default(hw, &data);
2419 mac->ledctl_default = er32(LEDCTL);
2420 mac->ledctl_mode1 = mac->ledctl_default;
2421 mac->ledctl_mode2 = mac->ledctl_default;
2423 for (i = 0; i < 4; i++) {
2424 temp = (data >> (i << 2)) & E1000_LEDCTL_LED0_MODE_MASK;
2427 case ID_LED_ON1_DEF2:
2428 case ID_LED_ON1_ON2:
2429 case ID_LED_ON1_OFF2:
2430 mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift);
2431 mac->ledctl_mode1 |= (ledctl_on << shift);
2433 case ID_LED_OFF1_DEF2:
2434 case ID_LED_OFF1_ON2:
2435 case ID_LED_OFF1_OFF2:
2436 mac->ledctl_mode1 &= ~(E1000_PHY_LED0_MASK << shift);
2437 mac->ledctl_mode1 |= (ledctl_off << shift);
2444 case ID_LED_DEF1_ON2:
2445 case ID_LED_ON1_ON2:
2446 case ID_LED_OFF1_ON2:
2447 mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift);
2448 mac->ledctl_mode2 |= (ledctl_on << shift);
2450 case ID_LED_DEF1_OFF2:
2451 case ID_LED_ON1_OFF2:
2452 case ID_LED_OFF1_OFF2:
2453 mac->ledctl_mode2 &= ~(E1000_PHY_LED0_MASK << shift);
2454 mac->ledctl_mode2 |= (ledctl_off << shift);
2467 * e1000_get_bus_info_ich8lan - Get/Set the bus type and width
2468 * @hw: pointer to the HW structure
2470 * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability
2471 * register, so the the bus width is hard coded.
2473 static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
2475 struct e1000_bus_info *bus = &hw->bus;
2478 ret_val = e1000e_get_bus_info_pcie(hw);
2481 * ICH devices are "PCI Express"-ish. They have
2482 * a configuration space, but do not contain
2483 * PCI Express Capability registers, so bus width
2484 * must be hardcoded.
2486 if (bus->width == e1000_bus_width_unknown)
2487 bus->width = e1000_bus_width_pcie_x1;
2493 * e1000_reset_hw_ich8lan - Reset the hardware
2494 * @hw: pointer to the HW structure
2496 * Does a full reset of the hardware which includes a reset of the PHY and
2499 static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
2501 struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
2507 * Prevent the PCI-E bus from sticking if there is no TLP connection
2508 * on the last TLP read/write transaction when MAC is reset.
2510 ret_val = e1000e_disable_pcie_master(hw);
2512 e_dbg("PCI-E Master disable polling has failed.\n");
2515 e_dbg("Masking off all interrupts\n");
2516 ew32(IMC, 0xffffffff);
2519 * Disable the Transmit and Receive units. Then delay to allow
2520 * any pending transactions to complete before we hit the MAC
2521 * with the global reset.
2524 ew32(TCTL, E1000_TCTL_PSP);
2529 /* Workaround for ICH8 bit corruption issue in FIFO memory */
2530 if (hw->mac.type == e1000_ich8lan) {
2531 /* Set Tx and Rx buffer allocation to 8k apiece. */
2532 ew32(PBA, E1000_PBA_8K);
2533 /* Set Packet Buffer Size to 16k. */
2534 ew32(PBS, E1000_PBS_16K);
2537 if (hw->mac.type == e1000_pchlan) {
2538 /* Save the NVM K1 bit setting*/
2539 ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, ®);
2543 if (reg & E1000_NVM_K1_ENABLE)
2544 dev_spec->nvm_k1_enabled = true;
2546 dev_spec->nvm_k1_enabled = false;
2551 if (!e1000_check_reset_block(hw)) {
2552 /* Clear PHY Reset Asserted bit */
2553 if (hw->mac.type >= e1000_pchlan) {
2554 u32 status = er32(STATUS);
2555 ew32(STATUS, status & ~E1000_STATUS_PHYRA);
2559 * PHY HW reset requires MAC CORE reset at the same
2560 * time to make sure the interface between MAC and the
2561 * external PHY is reset.
2563 ctrl |= E1000_CTRL_PHY_RST;
2565 ret_val = e1000_acquire_swflag_ich8lan(hw);
2566 e_dbg("Issuing a global reset to ich8lan\n");
2567 ew32(CTRL, (ctrl | E1000_CTRL_RST));
2571 e1000_release_swflag_ich8lan(hw);
2573 /* Perform any necessary post-reset workarounds */
2574 if (hw->mac.type == e1000_pchlan)
2575 ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
2577 if (ctrl & E1000_CTRL_PHY_RST)
2578 ret_val = hw->phy.ops.get_cfg_done(hw);
2580 if (hw->mac.type >= e1000_ich10lan) {
2581 e1000_lan_init_done_ich8lan(hw);
2583 ret_val = e1000e_get_auto_rd_done(hw);
2586 * When auto config read does not complete, do not
2587 * return with an error. This can happen in situations
2588 * where there is no eeprom and prevents getting link.
2590 e_dbg("Auto Read Done did not complete\n");
2593 /* Dummy read to clear the phy wakeup bit after lcd reset */
2594 if (hw->mac.type == e1000_pchlan)
2595 e1e_rphy(hw, BM_WUC, ®);
2597 ret_val = e1000_sw_lcd_config_ich8lan(hw);
2601 if (hw->mac.type == e1000_pchlan) {
2602 ret_val = e1000_oem_bits_config_ich8lan(hw, true);
2607 * For PCH, this write will make sure that any noise
2608 * will be detected as a CRC error and be dropped rather than show up
2609 * as a bad packet to the DMA engine.
2611 if (hw->mac.type == e1000_pchlan)
2612 ew32(CRC_OFFSET, 0x65656565);
2614 ew32(IMC, 0xffffffff);
2617 kab = er32(KABGTXD);
2618 kab |= E1000_KABGTXD_BGSQLBIAS;
2626 * e1000_init_hw_ich8lan - Initialize the hardware
2627 * @hw: pointer to the HW structure
2629 * Prepares the hardware for transmit and receive by doing the following:
2630 * - initialize hardware bits
2631 * - initialize LED identification
2632 * - setup receive address registers
2633 * - setup flow control
2634 * - setup transmit descriptors
2635 * - clear statistics
2637 static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
2639 struct e1000_mac_info *mac = &hw->mac;
2640 u32 ctrl_ext, txdctl, snoop;
2644 e1000_initialize_hw_bits_ich8lan(hw);
2646 /* Initialize identification LED */
2647 ret_val = mac->ops.id_led_init(hw);
2649 e_dbg("Error initializing identification LED\n");
2650 /* This is not fatal and we should not stop init due to this */
2652 /* Setup the receive address. */
2653 e1000e_init_rx_addrs(hw, mac->rar_entry_count);
2655 /* Zero out the Multicast HASH table */
2656 e_dbg("Zeroing the MTA\n");
2657 for (i = 0; i < mac->mta_reg_count; i++)
2658 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
2661 * The 82578 Rx buffer will stall if wakeup is enabled in host and
2662 * the ME. Reading the BM_WUC register will clear the host wakeup bit.
2663 * Reset the phy after disabling host wakeup to reset the Rx buffer.
2665 if (hw->phy.type == e1000_phy_82578) {
2666 hw->phy.ops.read_reg(hw, BM_WUC, &i);
2667 ret_val = e1000_phy_hw_reset_ich8lan(hw);
2672 /* Setup link and flow control */
2673 ret_val = e1000_setup_link_ich8lan(hw);
2675 /* Set the transmit descriptor write-back policy for both queues */
2676 txdctl = er32(TXDCTL(0));
2677 txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) |
2678 E1000_TXDCTL_FULL_TX_DESC_WB;
2679 txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) |
2680 E1000_TXDCTL_MAX_TX_DESC_PREFETCH;
2681 ew32(TXDCTL(0), txdctl);
2682 txdctl = er32(TXDCTL(1));
2683 txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) |
2684 E1000_TXDCTL_FULL_TX_DESC_WB;
2685 txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) |
2686 E1000_TXDCTL_MAX_TX_DESC_PREFETCH;
2687 ew32(TXDCTL(1), txdctl);
2690 * ICH8 has opposite polarity of no_snoop bits.
2691 * By default, we should use snoop behavior.
2693 if (mac->type == e1000_ich8lan)
2694 snoop = PCIE_ICH8_SNOOP_ALL;
2696 snoop = (u32) ~(PCIE_NO_SNOOP_ALL);
2697 e1000e_set_pcie_no_snoop(hw, snoop);
2699 ctrl_ext = er32(CTRL_EXT);
2700 ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
2701 ew32(CTRL_EXT, ctrl_ext);
2704 * Clear all of the statistics registers (clear on read). It is
2705 * important that we do this after we have tried to establish link
2706 * because the symbol error count will increment wildly if there
2709 e1000_clear_hw_cntrs_ich8lan(hw);
2714 * e1000_initialize_hw_bits_ich8lan - Initialize required hardware bits
2715 * @hw: pointer to the HW structure
2717 * Sets/Clears required hardware bits necessary for correctly setting up the
2718 * hardware for transmit and receive.
2720 static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw)
2724 /* Extended Device Control */
2725 reg = er32(CTRL_EXT);
2727 /* Enable PHY low-power state when MAC is at D3 w/o WoL */
2728 if (hw->mac.type >= e1000_pchlan)
2729 reg |= E1000_CTRL_EXT_PHYPDEN;
2730 ew32(CTRL_EXT, reg);
2732 /* Transmit Descriptor Control 0 */
2733 reg = er32(TXDCTL(0));
2735 ew32(TXDCTL(0), reg);
2737 /* Transmit Descriptor Control 1 */
2738 reg = er32(TXDCTL(1));
2740 ew32(TXDCTL(1), reg);
2742 /* Transmit Arbitration Control 0 */
2743 reg = er32(TARC(0));
2744 if (hw->mac.type == e1000_ich8lan)
2745 reg |= (1 << 28) | (1 << 29);
2746 reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27);
2749 /* Transmit Arbitration Control 1 */
2750 reg = er32(TARC(1));
2751 if (er32(TCTL) & E1000_TCTL_MULR)
2755 reg |= (1 << 24) | (1 << 26) | (1 << 30);
2759 if (hw->mac.type == e1000_ich8lan) {
2766 * work-around descriptor data corruption issue during nfs v2 udp
2767 * traffic, just disable the nfs filtering capability
2770 reg |= (E1000_RFCTL_NFSW_DIS | E1000_RFCTL_NFSR_DIS);
2777 * e1000_setup_link_ich8lan - Setup flow control and link settings
2778 * @hw: pointer to the HW structure
2780 * Determines which flow control settings to use, then configures flow
2781 * control. Calls the appropriate media-specific link configuration
2782 * function. Assuming the adapter has a valid link partner, a valid link
2783 * should be established. Assumes the hardware has previously been reset
2784 * and the transmitter and receiver are not enabled.
2786 static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw)
2790 if (e1000_check_reset_block(hw))
2794 * ICH parts do not have a word in the NVM to determine
2795 * the default flow control setting, so we explicitly
2798 if (hw->fc.requested_mode == e1000_fc_default) {
2799 /* Workaround h/w hang when Tx flow control enabled */
2800 if (hw->mac.type == e1000_pchlan)
2801 hw->fc.requested_mode = e1000_fc_rx_pause;
2803 hw->fc.requested_mode = e1000_fc_full;
2807 * Save off the requested flow control mode for use later. Depending
2808 * on the link partner's capabilities, we may or may not use this mode.
2810 hw->fc.current_mode = hw->fc.requested_mode;
2812 e_dbg("After fix-ups FlowControl is now = %x\n",
2813 hw->fc.current_mode);
2815 /* Continue to configure the copper link. */
2816 ret_val = e1000_setup_copper_link_ich8lan(hw);
2820 ew32(FCTTV, hw->fc.pause_time);
2821 if ((hw->phy.type == e1000_phy_82578) ||
2822 (hw->phy.type == e1000_phy_82577)) {
2823 ret_val = hw->phy.ops.write_reg(hw,
2824 PHY_REG(BM_PORT_CTRL_PAGE, 27),
2830 return e1000e_set_fc_watermarks(hw);
2834 * e1000_setup_copper_link_ich8lan - Configure MAC/PHY interface
2835 * @hw: pointer to the HW structure
2837 * Configures the kumeran interface to the PHY to wait the appropriate time
2838 * when polling the PHY, then call the generic setup_copper_link to finish
2839 * configuring the copper link.
2841 static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw)
2848 ctrl |= E1000_CTRL_SLU;
2849 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
2853 * Set the mac to wait the maximum time between each iteration
2854 * and increase the max iterations when polling the phy;
2855 * this fixes erroneous timeouts at 10Mbps.
2857 ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_TIMEOUTS, 0xFFFF);
2860 ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
2865 ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
2870 switch (hw->phy.type) {
2871 case e1000_phy_igp_3:
2872 ret_val = e1000e_copper_link_setup_igp(hw);
2877 case e1000_phy_82578:
2878 ret_val = e1000e_copper_link_setup_m88(hw);
2882 case e1000_phy_82577:
2883 ret_val = e1000_copper_link_setup_82577(hw);
2888 ret_val = hw->phy.ops.read_reg(hw, IFE_PHY_MDIX_CONTROL,
2893 reg_data &= ~IFE_PMC_AUTO_MDIX;
2895 switch (hw->phy.mdix) {
2897 reg_data &= ~IFE_PMC_FORCE_MDIX;
2900 reg_data |= IFE_PMC_FORCE_MDIX;
2904 reg_data |= IFE_PMC_AUTO_MDIX;
2907 ret_val = hw->phy.ops.write_reg(hw, IFE_PHY_MDIX_CONTROL,
2915 return e1000e_setup_copper_link(hw);
2919 * e1000_get_link_up_info_ich8lan - Get current link speed and duplex
2920 * @hw: pointer to the HW structure
2921 * @speed: pointer to store current link speed
2922 * @duplex: pointer to store the current link duplex
2924 * Calls the generic get_speed_and_duplex to retrieve the current link
2925 * information and then calls the Kumeran lock loss workaround for links at
2928 static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed,
2933 ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex);
2937 if ((hw->mac.type == e1000_ich8lan) &&
2938 (hw->phy.type == e1000_phy_igp_3) &&
2939 (*speed == SPEED_1000)) {
2940 ret_val = e1000_kmrn_lock_loss_workaround_ich8lan(hw);
2947 * e1000_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround
2948 * @hw: pointer to the HW structure
2950 * Work-around for 82566 Kumeran PCS lock loss:
2951 * On link status change (i.e. PCI reset, speed change) and link is up and
2953 * 0) if workaround is optionally disabled do nothing
2954 * 1) wait 1ms for Kumeran link to come up
2955 * 2) check Kumeran Diagnostic register PCS lock loss bit
2956 * 3) if not set the link is locked (all is good), otherwise...
2958 * 5) repeat up to 10 times
2959 * Note: this is only called for IGP3 copper when speed is 1gb.
2961 static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw)
2963 struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
2969 if (!dev_spec->kmrn_lock_loss_workaround_enabled)
2973 * Make sure link is up before proceeding. If not just return.
2974 * Attempting this while link is negotiating fouled up link
2977 ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
2981 for (i = 0; i < 10; i++) {
2982 /* read once to clear */
2983 ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data);
2986 /* and again to get new status */
2987 ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data);
2991 /* check for PCS lock */
2992 if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS))
2995 /* Issue PHY reset */
2996 e1000_phy_hw_reset(hw);
2999 /* Disable GigE link negotiation */
3000 phy_ctrl = er32(PHY_CTRL);
3001 phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE |
3002 E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
3003 ew32(PHY_CTRL, phy_ctrl);
3006 * Call gig speed drop workaround on Gig disable before accessing
3009 e1000e_gig_downshift_workaround_ich8lan(hw);
3011 /* unable to acquire PCS lock */
3012 return -E1000_ERR_PHY;
3016 * e1000_set_kmrn_lock_loss_workaround_ich8lan - Set Kumeran workaround state
3017 * @hw: pointer to the HW structure
3018 * @state: boolean value used to set the current Kumeran workaround state
3020 * If ICH8, set the current Kumeran workaround state (enabled - true
3021 * /disabled - false).
3023 void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
3026 struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
3028 if (hw->mac.type != e1000_ich8lan) {
3029 e_dbg("Workaround applies to ICH8 only.\n");
3033 dev_spec->kmrn_lock_loss_workaround_enabled = state;
3037 * e1000_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3
3038 * @hw: pointer to the HW structure
3040 * Workaround for 82566 power-down on D3 entry:
3041 * 1) disable gigabit link
3042 * 2) write VR power-down enable
3044 * Continue if successful, else issue LCD reset and repeat
3046 void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
3052 if (hw->phy.type != e1000_phy_igp_3)
3055 /* Try the workaround twice (if needed) */
3058 reg = er32(PHY_CTRL);
3059 reg |= (E1000_PHY_CTRL_GBE_DISABLE |
3060 E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
3061 ew32(PHY_CTRL, reg);
3064 * Call gig speed drop workaround on Gig disable before
3065 * accessing any PHY registers
3067 if (hw->mac.type == e1000_ich8lan)
3068 e1000e_gig_downshift_workaround_ich8lan(hw);
3070 /* Write VR power-down enable */
3071 e1e_rphy(hw, IGP3_VR_CTRL, &data);
3072 data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK;
3073 e1e_wphy(hw, IGP3_VR_CTRL, data | IGP3_VR_CTRL_MODE_SHUTDOWN);
3075 /* Read it back and test */
3076 e1e_rphy(hw, IGP3_VR_CTRL, &data);
3077 data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK;
3078 if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry)
3081 /* Issue PHY reset and repeat at most one more time */
3083 ew32(CTRL, reg | E1000_CTRL_PHY_RST);
3089 * e1000e_gig_downshift_workaround_ich8lan - WoL from S5 stops working
3090 * @hw: pointer to the HW structure
3092 * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC),
3093 * LPLU, Gig disable, MDIC PHY reset):
3094 * 1) Set Kumeran Near-end loopback
3095 * 2) Clear Kumeran Near-end loopback
3096 * Should only be called for ICH8[m] devices with IGP_3 Phy.
3098 void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
3103 if ((hw->mac.type != e1000_ich8lan) ||
3104 (hw->phy.type != e1000_phy_igp_3))
3107 ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
3111 reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK;
3112 ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
3116 reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK;
3117 ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
3122 * e1000e_disable_gig_wol_ich8lan - disable gig during WoL
3123 * @hw: pointer to the HW structure
3125 * During S0 to Sx transition, it is possible the link remains at gig
3126 * instead of negotiating to a lower speed. Before going to Sx, set
3127 * 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation
3130 * Should only be called for applicable parts.
3132 void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
3136 switch (hw->mac.type) {
3139 case e1000_ich10lan:
3141 phy_ctrl = er32(PHY_CTRL);
3142 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU |
3143 E1000_PHY_CTRL_GBE_DISABLE;
3144 ew32(PHY_CTRL, phy_ctrl);
3146 if (hw->mac.type == e1000_pchlan)
3147 e1000_phy_hw_reset_ich8lan(hw);
3156 * e1000_cleanup_led_ich8lan - Restore the default LED operation
3157 * @hw: pointer to the HW structure
3159 * Return the LED back to the default configuration.
3161 static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw)
3163 if (hw->phy.type == e1000_phy_ife)
3164 return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0);
3166 ew32(LEDCTL, hw->mac.ledctl_default);
3171 * e1000_led_on_ich8lan - Turn LEDs on
3172 * @hw: pointer to the HW structure
3176 static s32 e1000_led_on_ich8lan(struct e1000_hw *hw)
3178 if (hw->phy.type == e1000_phy_ife)
3179 return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED,
3180 (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON));
3182 ew32(LEDCTL, hw->mac.ledctl_mode2);
3187 * e1000_led_off_ich8lan - Turn LEDs off
3188 * @hw: pointer to the HW structure
3190 * Turn off the LEDs.
3192 static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
3194 if (hw->phy.type == e1000_phy_ife)
3195 return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED,
3196 (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
3198 ew32(LEDCTL, hw->mac.ledctl_mode1);
3203 * e1000_setup_led_pchlan - Configures SW controllable LED
3204 * @hw: pointer to the HW structure
3206 * This prepares the SW controllable LED for use.
3208 static s32 e1000_setup_led_pchlan(struct e1000_hw *hw)
3210 return hw->phy.ops.write_reg(hw, HV_LED_CONFIG,
3211 (u16)hw->mac.ledctl_mode1);
3215 * e1000_cleanup_led_pchlan - Restore the default LED operation
3216 * @hw: pointer to the HW structure
3218 * Return the LED back to the default configuration.
3220 static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw)
3222 return hw->phy.ops.write_reg(hw, HV_LED_CONFIG,
3223 (u16)hw->mac.ledctl_default);
3227 * e1000_led_on_pchlan - Turn LEDs on
3228 * @hw: pointer to the HW structure
3232 static s32 e1000_led_on_pchlan(struct e1000_hw *hw)
3234 u16 data = (u16)hw->mac.ledctl_mode2;
3238 * If no link, then turn LED on by setting the invert bit
3239 * for each LED that's mode is "link_up" in ledctl_mode2.
3241 if (!(er32(STATUS) & E1000_STATUS_LU)) {
3242 for (i = 0; i < 3; i++) {
3243 led = (data >> (i * 5)) & E1000_PHY_LED0_MASK;
3244 if ((led & E1000_PHY_LED0_MODE_MASK) !=
3245 E1000_LEDCTL_MODE_LINK_UP)
3247 if (led & E1000_PHY_LED0_IVRT)
3248 data &= ~(E1000_PHY_LED0_IVRT << (i * 5));
3250 data |= (E1000_PHY_LED0_IVRT << (i * 5));
3254 return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, data);
3258 * e1000_led_off_pchlan - Turn LEDs off
3259 * @hw: pointer to the HW structure
3261 * Turn off the LEDs.
3263 static s32 e1000_led_off_pchlan(struct e1000_hw *hw)
3265 u16 data = (u16)hw->mac.ledctl_mode1;
3269 * If no link, then turn LED off by clearing the invert bit
3270 * for each LED that's mode is "link_up" in ledctl_mode1.
3272 if (!(er32(STATUS) & E1000_STATUS_LU)) {
3273 for (i = 0; i < 3; i++) {
3274 led = (data >> (i * 5)) & E1000_PHY_LED0_MASK;
3275 if ((led & E1000_PHY_LED0_MODE_MASK) !=
3276 E1000_LEDCTL_MODE_LINK_UP)
3278 if (led & E1000_PHY_LED0_IVRT)
3279 data &= ~(E1000_PHY_LED0_IVRT << (i * 5));
3281 data |= (E1000_PHY_LED0_IVRT << (i * 5));
3285 return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, data);
3289 * e1000_get_cfg_done_ich8lan - Read config done bit
3290 * @hw: pointer to the HW structure
3292 * Read the management control register for the config done bit for
3293 * completion status. NOTE: silicon which is EEPROM-less will fail trying
3294 * to read the config done bit, so an error is *ONLY* logged and returns
3295 * 0. If we were to return with error, EEPROM-less silicon
3296 * would not be able to be reset or change link.
3298 static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
3302 if (hw->mac.type >= e1000_pchlan) {
3303 u32 status = er32(STATUS);
3305 if (status & E1000_STATUS_PHYRA)
3306 ew32(STATUS, status & ~E1000_STATUS_PHYRA);
3308 e_dbg("PHY Reset Asserted not set - needs delay\n");
3311 e1000e_get_cfg_done(hw);
3313 /* If EEPROM is not marked present, init the IGP 3 PHY manually */
3314 if ((hw->mac.type != e1000_ich10lan) &&
3315 (hw->mac.type != e1000_pchlan)) {
3316 if (((er32(EECD) & E1000_EECD_PRES) == 0) &&
3317 (hw->phy.type == e1000_phy_igp_3)) {
3318 e1000e_phy_init_script_igp3(hw);
3321 if (e1000_valid_nvm_bank_detect_ich8lan(hw, &bank)) {
3322 /* Maybe we should do a basic PHY config */
3323 e_dbg("EEPROM not present\n");
3324 return -E1000_ERR_CONFIG;
3332 * e1000_power_down_phy_copper_ich8lan - Remove link during PHY power down
3333 * @hw: pointer to the HW structure
3335 * In the case of a PHY power down to save power, or to turn off link during a
3336 * driver unload, or wake on lan is not enabled, remove the link.
3338 static void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw)
3340 /* If the management interface is not enabled, then power down */
3341 if (!(hw->mac.ops.check_mng_mode(hw) ||
3342 hw->phy.ops.check_reset_block(hw)))
3343 e1000_power_down_phy_copper(hw);
3349 * e1000_clear_hw_cntrs_ich8lan - Clear statistical counters
3350 * @hw: pointer to the HW structure
3352 * Clears hardware counters specific to the silicon family and calls
3353 * clear_hw_cntrs_generic to clear all general purpose counters.
3355 static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw)
3359 e1000e_clear_hw_cntrs_base(hw);
3375 /* Clear PHY statistics registers */
3376 if ((hw->phy.type == e1000_phy_82578) ||
3377 (hw->phy.type == e1000_phy_82577)) {
3378 hw->phy.ops.read_reg(hw, HV_SCC_UPPER, &phy_data);
3379 hw->phy.ops.read_reg(hw, HV_SCC_LOWER, &phy_data);
3380 hw->phy.ops.read_reg(hw, HV_ECOL_UPPER, &phy_data);
3381 hw->phy.ops.read_reg(hw, HV_ECOL_LOWER, &phy_data);
3382 hw->phy.ops.read_reg(hw, HV_MCC_UPPER, &phy_data);
3383 hw->phy.ops.read_reg(hw, HV_MCC_LOWER, &phy_data);
3384 hw->phy.ops.read_reg(hw, HV_LATECOL_UPPER, &phy_data);
3385 hw->phy.ops.read_reg(hw, HV_LATECOL_LOWER, &phy_data);
3386 hw->phy.ops.read_reg(hw, HV_COLC_UPPER, &phy_data);
3387 hw->phy.ops.read_reg(hw, HV_COLC_LOWER, &phy_data);
3388 hw->phy.ops.read_reg(hw, HV_DC_UPPER, &phy_data);
3389 hw->phy.ops.read_reg(hw, HV_DC_LOWER, &phy_data);
3390 hw->phy.ops.read_reg(hw, HV_TNCRS_UPPER, &phy_data);
3391 hw->phy.ops.read_reg(hw, HV_TNCRS_LOWER, &phy_data);
3395 static struct e1000_mac_operations ich8_mac_ops = {
3396 .id_led_init = e1000e_id_led_init,
3397 .check_mng_mode = e1000_check_mng_mode_ich8lan,
3398 .check_for_link = e1000_check_for_copper_link_ich8lan,
3399 /* cleanup_led dependent on mac type */
3400 .clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan,
3401 .get_bus_info = e1000_get_bus_info_ich8lan,
3402 .set_lan_id = e1000_set_lan_id_single_port,
3403 .get_link_up_info = e1000_get_link_up_info_ich8lan,
3404 /* led_on dependent on mac type */
3405 /* led_off dependent on mac type */
3406 .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
3407 .reset_hw = e1000_reset_hw_ich8lan,
3408 .init_hw = e1000_init_hw_ich8lan,
3409 .setup_link = e1000_setup_link_ich8lan,
3410 .setup_physical_interface= e1000_setup_copper_link_ich8lan,
3411 /* id_led_init dependent on mac type */
3414 static struct e1000_phy_operations ich8_phy_ops = {
3415 .acquire = e1000_acquire_swflag_ich8lan,
3416 .check_reset_block = e1000_check_reset_block_ich8lan,
3418 .get_cfg_done = e1000_get_cfg_done_ich8lan,
3419 .get_cable_length = e1000e_get_cable_length_igp_2,
3420 .read_reg = e1000e_read_phy_reg_igp,
3421 .release = e1000_release_swflag_ich8lan,
3422 .reset = e1000_phy_hw_reset_ich8lan,
3423 .set_d0_lplu_state = e1000_set_d0_lplu_state_ich8lan,
3424 .set_d3_lplu_state = e1000_set_d3_lplu_state_ich8lan,
3425 .write_reg = e1000e_write_phy_reg_igp,
3428 static struct e1000_nvm_operations ich8_nvm_ops = {
3429 .acquire = e1000_acquire_nvm_ich8lan,
3430 .read = e1000_read_nvm_ich8lan,
3431 .release = e1000_release_nvm_ich8lan,
3432 .update = e1000_update_nvm_checksum_ich8lan,
3433 .valid_led_default = e1000_valid_led_default_ich8lan,
3434 .validate = e1000_validate_nvm_checksum_ich8lan,
3435 .write = e1000_write_nvm_ich8lan,
3438 struct e1000_info e1000_ich8_info = {
3439 .mac = e1000_ich8lan,
3440 .flags = FLAG_HAS_WOL
3442 | FLAG_RX_CSUM_ENABLED
3443 | FLAG_HAS_CTRLEXT_ON_LOAD
3448 .max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN,
3449 .get_variants = e1000_get_variants_ich8lan,
3450 .mac_ops = &ich8_mac_ops,
3451 .phy_ops = &ich8_phy_ops,
3452 .nvm_ops = &ich8_nvm_ops,
3455 struct e1000_info e1000_ich9_info = {
3456 .mac = e1000_ich9lan,
3457 .flags = FLAG_HAS_JUMBO_FRAMES
3460 | FLAG_RX_CSUM_ENABLED
3461 | FLAG_HAS_CTRLEXT_ON_LOAD
3467 .max_hw_frame_size = DEFAULT_JUMBO,
3468 .get_variants = e1000_get_variants_ich8lan,
3469 .mac_ops = &ich8_mac_ops,
3470 .phy_ops = &ich8_phy_ops,
3471 .nvm_ops = &ich8_nvm_ops,
3474 struct e1000_info e1000_ich10_info = {
3475 .mac = e1000_ich10lan,
3476 .flags = FLAG_HAS_JUMBO_FRAMES
3479 | FLAG_RX_CSUM_ENABLED
3480 | FLAG_HAS_CTRLEXT_ON_LOAD
3486 .max_hw_frame_size = DEFAULT_JUMBO,
3487 .get_variants = e1000_get_variants_ich8lan,
3488 .mac_ops = &ich8_mac_ops,
3489 .phy_ops = &ich8_phy_ops,
3490 .nvm_ops = &ich8_nvm_ops,
3493 struct e1000_info e1000_pch_info = {
3494 .mac = e1000_pchlan,
3495 .flags = FLAG_IS_ICH
3497 | FLAG_RX_CSUM_ENABLED
3498 | FLAG_HAS_CTRLEXT_ON_LOAD
3501 | FLAG_HAS_JUMBO_FRAMES
3502 | FLAG_DISABLE_FC_PAUSE_TIME /* errata */
3505 .max_hw_frame_size = 4096,
3506 .get_variants = e1000_get_variants_ich8lan,
3507 .mac_ops = &ich8_mac_ops,
3508 .phy_ops = &ich8_phy_ops,
3509 .nvm_ops = &ich8_nvm_ops,