SAFE public projects git trees. - safe/jmp/linux-2.6/blob - drivers/mmc/au1xmmc.c

   1 /*
   2  * linux/drivers/mmc/au1xmmc.c - AU1XX0 MMC driver
   3  *
   4  *  Copyright (c) 2005, Advanced Micro Devices, Inc.
   5  *
   6  *  Developed with help from the 2.4.30 MMC AU1XXX controller including
   7  *  the following copyright notices:
   8  *     Copyright (c) 2003-2004 Embedded Edge, LLC.
   9  *     Portions Copyright (C) 2002 Embedix, Inc
  10  *     Copyright 2002 Hewlett-Packard Company
  11
  12  *  2.6 version of this driver inspired by:
  13  *     (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman,
  14  *     All Rights Reserved.
  15  *     (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King,
  16  *     All Rights Reserved.
  17  *
  18
  19  * This program is free software; you can redistribute it and/or modify
  20  * it under the terms of the GNU General Public License version 2 as
  21  * published by the Free Software Foundation.
  22  */
  23
  24 /* Why is a timer used to detect insert events?
  25  *
  26  * From the AU1100 MMC application guide:
  27  * If the Au1100-based design is intended to support both MultiMediaCards
  28  * and 1- or 4-data bit SecureDigital cards, then the solution is to
  29  * connect a weak (560KOhm) pull-up resistor to connector pin 1.
  30  * In doing so, a MMC card never enters SPI-mode communications,
  31  * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective
  32  * (the low to high transition will not occur).
  33  *
  34  * So we use the timer to check the status manually.
  35  */
  36
  37 #include <linux/config.h>
  38 #include <linux/module.h>
  39 #include <linux/init.h>
  40 #include <linux/platform_device.h>
  41 #include <linux/mm.h>
  42 #include <linux/interrupt.h>
  43 #include <linux/dma-mapping.h>
  44
  45 #include <linux/mmc/host.h>
  46 #include <linux/mmc/protocol.h>
  47 #include <asm/io.h>
  48 #include <asm/mach-au1x00/au1000.h>
  49 #include <asm/mach-au1x00/au1xxx_dbdma.h>
  50 #include <asm/mach-au1x00/au1100_mmc.h>
  51 #include <asm/scatterlist.h>
  52
  53 #include <au1xxx.h>
  54 #include "au1xmmc.h"
  55
  56 #define DRIVER_NAME "au1xxx-mmc"
  57
  58 /* Set this to enable special debugging macros */
  59
  60 #ifdef DEBUG
  61 #define DBG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args)
  62 #else
  63 #define DBG(fmt, idx, args...)
  64 #endif
  65
  66 const struct {
  67         u32 iobase;
  68         u32 tx_devid, rx_devid;
  69         u16 bcsrpwr;
  70         u16 bcsrstatus;
  71         u16 wpstatus;
  72 } au1xmmc_card_table[] = {
  73         { SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0,
  74           BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP },
  75 #ifndef CONFIG_MIPS_DB1200
  76         { SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1,
  77           BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP }
  78 #endif
  79 };
  80
  81 #define AU1XMMC_CONTROLLER_COUNT \
  82         (sizeof(au1xmmc_card_table) / sizeof(au1xmmc_card_table[0]))
  83
  84 /* This array stores pointers for the hosts (used by the IRQ handler) */
  85 struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT];
  86 static int dma = 1;
  87
  88 #ifdef MODULE
  89 module_param(dma, bool, 0);
  90 MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)");
  91 #endif
  92
  93 static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
  94 {
  95         u32 val = au_readl(HOST_CONFIG(host));
  96         val |= mask;
  97         au_writel(val, HOST_CONFIG(host));
  98         au_sync();
  99 }
 100
 101 static inline void FLUSH_FIFO(struct au1xmmc_host *host)
 102 {
 103         u32 val = au_readl(HOST_CONFIG2(host));
 104
 105         au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
 106         au_sync_delay(1);
 107
 108         /* SEND_STOP will turn off clock control - this re-enables it */
 109         val &= ~SD_CONFIG2_DF;
 110
 111         au_writel(val, HOST_CONFIG2(host));
 112         au_sync();
 113 }
 114
 115 static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
 116 {
 117         u32 val = au_readl(HOST_CONFIG(host));
 118         val &= ~mask;
 119         au_writel(val, HOST_CONFIG(host));
 120         au_sync();
 121 }
 122
 123 static inline void SEND_STOP(struct au1xmmc_host *host)
 124 {
 125
 126         /* We know the value of CONFIG2, so avoid a read we don't need */
 127         u32 mask = SD_CONFIG2_EN;
 128
 129         WARN_ON(host->status != HOST_S_DATA);
 130         host->status = HOST_S_STOP;
 131
 132         au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host));
 133         au_sync();
 134
 135         /* Send the stop commmand */
 136         au_writel(STOP_CMD, HOST_CMD(host));
 137 }
 138
 139 static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
 140 {
 141
 142         u32 val = au1xmmc_card_table[host->id].bcsrpwr;
 143
 144         bcsr->board &= ~val;
 145         if (state) bcsr->board |= val;
 146
 147         au_sync_delay(1);
 148 }
 149
 150 static inline int au1xmmc_card_inserted(struct au1xmmc_host *host)
 151 {
 152         return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus)
 153                 ? 1 : 0;
 154 }
 155
 156 static inline int au1xmmc_card_readonly(struct au1xmmc_host *host)
 157 {
 158         return (bcsr->status & au1xmmc_card_table[host->id].wpstatus)
 159                 ? 1 : 0;
 160 }
 161
 162 static void au1xmmc_finish_request(struct au1xmmc_host *host)
 163 {
 164
 165         struct mmc_request *mrq = host->mrq;
 166
 167         host->mrq = NULL;
 168         host->flags &= HOST_F_ACTIVE;
 169
 170         host->dma.len = 0;
 171         host->dma.dir = 0;
 172
 173         host->pio.index  = 0;
 174         host->pio.offset = 0;
 175         host->pio.len = 0;
 176
 177         host->status = HOST_S_IDLE;
 178
 179         bcsr->disk_leds |= (1 << 8);
 180
 181         mmc_request_done(host->mmc, mrq);
 182 }
 183
 184 static void au1xmmc_tasklet_finish(unsigned long param)
 185 {
 186         struct au1xmmc_host *host = (struct au1xmmc_host *) param;
 187         au1xmmc_finish_request(host);
 188 }
 189
 190 static int au1xmmc_send_command(struct au1xmmc_host *host, int wait,
 191                                 struct mmc_command *cmd)
 192 {
 193
 194         u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT);
 195
 196         switch (mmc_resp_type(cmd)) {
 197         case MMC_RSP_R1:
 198                 mmccmd |= SD_CMD_RT_1;
 199                 break;
 200         case MMC_RSP_R1B:
 201                 mmccmd |= SD_CMD_RT_1B;
 202                 break;
 203         case MMC_RSP_R2:
 204                 mmccmd |= SD_CMD_RT_2;
 205                 break;
 206         case MMC_RSP_R3:
 207                 mmccmd |= SD_CMD_RT_3;
 208                 break;
 209         }
 210
 211         switch(cmd->opcode) {
 212         case MMC_READ_SINGLE_BLOCK:
 213         case SD_APP_SEND_SCR:
 214                 mmccmd |= SD_CMD_CT_2;
 215                 break;
 216         case MMC_READ_MULTIPLE_BLOCK:
 217                 mmccmd |= SD_CMD_CT_4;
 218                 break;
 219         case MMC_WRITE_BLOCK:
 220                 mmccmd |= SD_CMD_CT_1;
 221                 break;
 222
 223         case MMC_WRITE_MULTIPLE_BLOCK:
 224                 mmccmd |= SD_CMD_CT_3;
 225                 break;
 226         case MMC_STOP_TRANSMISSION:
 227                 mmccmd |= SD_CMD_CT_7;
 228                 break;
 229         }
 230
 231         au_writel(cmd->arg, HOST_CMDARG(host));
 232         au_sync();
 233
 234         if (wait)
 235                 IRQ_OFF(host, SD_CONFIG_CR);
 236
 237         au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
 238         au_sync();
 239
 240         /* Wait for the command to go on the line */
 241
 242         while(1) {
 243                 if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO))
 244                         break;
 245         }
 246
 247         /* Wait for the command to come back */
 248
 249         if (wait) {
 250                 u32 status = au_readl(HOST_STATUS(host));
 251
 252                 while(!(status & SD_STATUS_CR))
 253                         status = au_readl(HOST_STATUS(host));
 254
 255                 /* Clear the CR status */
 256                 au_writel(SD_STATUS_CR, HOST_STATUS(host));
 257
 258                 IRQ_ON(host, SD_CONFIG_CR);
 259         }
 260
 261         return MMC_ERR_NONE;
 262 }
 263
 264 static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status)
 265 {
 266
 267         struct mmc_request *mrq = host->mrq;
 268         struct mmc_data *data;
 269         u32 crc;
 270
 271         WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP);
 272
 273         if (host->mrq == NULL)
 274                 return;
 275
 276         data = mrq->cmd->data;
 277
 278         if (status == 0)
 279                 status = au_readl(HOST_STATUS(host));
 280
 281         /* The transaction is really over when the SD_STATUS_DB bit is clear */
 282
 283         while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
 284                 status = au_readl(HOST_STATUS(host));
 285
 286         data->error = MMC_ERR_NONE;
 287         dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);
 288
 289         /* Process any errors */
 290
 291         crc = (status & (SD_STATUS_WC | SD_STATUS_RC));
 292         if (host->flags & HOST_F_XMIT)
 293                 crc |= ((status & 0x07) == 0x02) ? 0 : 1;
 294
 295         if (crc)
 296                 data->error = MMC_ERR_BADCRC;
 297
 298         /* Clear the CRC bits */
 299         au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
 300
 301         data->bytes_xfered = 0;
 302
 303         if (data->error == MMC_ERR_NONE) {
 304                 if (host->flags & HOST_F_DMA) {
 305                         u32 chan = DMA_CHANNEL(host);
 306
 307                         chan_tab_t *c = *((chan_tab_t **) chan);
 308                         au1x_dma_chan_t *cp = c->chan_ptr;
 309                         data->bytes_xfered = cp->ddma_bytecnt;
 310                 }
 311                 else
 312                         data->bytes_xfered =
 313                                 (data->blocks * (1 << data->blksz_bits)) -
 314                                 host->pio.len;
 315         }
 316
 317         au1xmmc_finish_request(host);
 318 }
 319
 320 static void au1xmmc_tasklet_data(unsigned long param)
 321 {
 322         struct au1xmmc_host *host = (struct au1xmmc_host *) param;
 323
 324         u32 status = au_readl(HOST_STATUS(host));
 325         au1xmmc_data_complete(host, status);
 326 }
 327
 328 #define AU1XMMC_MAX_TRANSFER 8
 329
 330 static void au1xmmc_send_pio(struct au1xmmc_host *host)
 331 {
 332
 333         struct mmc_data *data = 0;
 334         int sg_len, max, count = 0;
 335         unsigned char *sg_ptr;
 336         u32 status = 0;
 337         struct scatterlist *sg;
 338
 339         data = host->mrq->data;
 340
 341         if (!(host->flags & HOST_F_XMIT))
 342                 return;
 343
 344         /* This is the pointer to the data buffer */
 345         sg = &data->sg[host->pio.index];
 346         sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
 347
 348         /* This is the space left inside the buffer */
 349         sg_len = data->sg[host->pio.index].length - host->pio.offset;
 350
 351         /* Check to if we need less then the size of the sg_buffer */
 352
 353         max = (sg_len > host->pio.len) ? host->pio.len : sg_len;
 354         if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER;
 355
 356         for(count = 0; count < max; count++ ) {
 357                 unsigned char val;
 358
 359                 status = au_readl(HOST_STATUS(host));
 360
 361                 if (!(status & SD_STATUS_TH))
 362                         break;
 363
 364                 val = *sg_ptr++;
 365
 366                 au_writel((unsigned long) val, HOST_TXPORT(host));
 367                 au_sync();
 368         }
 369
 370         host->pio.len -= count;
 371         host->pio.offset += count;
 372
 373         if (count == sg_len) {
 374                 host->pio.index++;
 375                 host->pio.offset = 0;
 376         }
 377
 378         if (host->pio.len == 0) {
 379                 IRQ_OFF(host, SD_CONFIG_TH);
 380
 381                 if (host->flags & HOST_F_STOP)
 382                         SEND_STOP(host);
 383
 384                 tasklet_schedule(&host->data_task);
 385         }
 386 }
 387
 388 static void au1xmmc_receive_pio(struct au1xmmc_host *host)
 389 {
 390
 391         struct mmc_data *data = 0;
 392         int sg_len = 0, max = 0, count = 0;
 393         unsigned char *sg_ptr = 0;
 394         u32 status = 0;
 395         struct scatterlist *sg;
 396
 397         data = host->mrq->data;
 398
 399         if (!(host->flags & HOST_F_RECV))
 400                 return;
 401
 402         max = host->pio.len;
 403
 404         if (host->pio.index < host->dma.len) {
 405                 sg = &data->sg[host->pio.index];
 406                 sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
 407
 408                 /* This is the space left inside the buffer */
 409                 sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset;
 410
 411                 /* Check to if we need less then the size of the sg_buffer */
 412                 if (sg_len < max) max = sg_len;
 413         }
 414
 415         if (max > AU1XMMC_MAX_TRANSFER)
 416                 max = AU1XMMC_MAX_TRANSFER;
 417
 418         for(count = 0; count < max; count++ ) {
 419                 u32 val;
 420                 status = au_readl(HOST_STATUS(host));
 421
 422                 if (!(status & SD_STATUS_NE))
 423                         break;
 424
 425                 if (status & SD_STATUS_RC) {
 426                         DBG("RX CRC Error [%d + %d].\n", host->id,
 427                                         host->pio.len, count);
 428                         break;
 429                 }
 430
 431                 if (status & SD_STATUS_RO) {
 432                         DBG("RX Overrun [%d + %d]\n", host->id,
 433                                         host->pio.len, count);
 434                         break;
 435                 }
 436                 else if (status & SD_STATUS_RU) {
 437                         DBG("RX Underrun [%d + %d]\n", host->id,
 438                                         host->pio.len,  count);
 439                         break;
 440                 }
 441
 442                 val = au_readl(HOST_RXPORT(host));
 443
 444                 if (sg_ptr)
 445                         *sg_ptr++ = (unsigned char) (val & 0xFF);
 446         }
 447
 448         host->pio.len -= count;
 449         host->pio.offset += count;
 450
 451         if (sg_len && count == sg_len) {
 452                 host->pio.index++;
 453                 host->pio.offset = 0;
 454         }
 455
 456         if (host->pio.len == 0) {
 457                 //IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF);
 458                 IRQ_OFF(host, SD_CONFIG_NE);
 459
 460                 if (host->flags & HOST_F_STOP)
 461                         SEND_STOP(host);
 462
 463                 tasklet_schedule(&host->data_task);
 464         }
 465 }
 466
 467 /* static void au1xmmc_cmd_complete
 468    This is called when a command has been completed - grab the response
 469    and check for errors.  Then start the data transfer if it is indicated.
 470 */
 471
 472 static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status)
 473 {
 474
 475         struct mmc_request *mrq = host->mrq;
 476         struct mmc_command *cmd;
 477         int trans;
 478
 479         if (!host->mrq)
 480                 return;
 481
 482         cmd = mrq->cmd;
 483         cmd->error = MMC_ERR_NONE;
 484
 485         if (cmd->flags & MMC_RSP_PRESENT) {
 486                 if (cmd->flags & MMC_RSP_136) {
 487                         u32 r[4];
 488                         int i;
 489
 490                         r[0] = au_readl(host->iobase + SD_RESP3);
 491                         r[1] = au_readl(host->iobase + SD_RESP2);
 492                         r[2] = au_readl(host->iobase + SD_RESP1);
 493                         r[3] = au_readl(host->iobase + SD_RESP0);
 494
 495                         /* The CRC is omitted from the response, so really
 496                          * we only got 120 bytes, but the engine expects
 497                          * 128 bits, so we have to shift things up
 498                          */
 499
 500                         for(i = 0; i < 4; i++) {
 501                                 cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8;
 502                                 if (i != 3)
 503                                         cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24;
 504                         }
 505                 } else {
 506                         /* Techincally, we should be getting all 48 bits of
 507                          * the response (SD_RESP1 + SD_RESP2), but because
 508                          * our response omits the CRC, our data ends up
 509                          * being shifted 8 bits to the right.  In this case,
 510                          * that means that the OSR data starts at bit 31,
 511                          * so we can just read RESP0 and return that
 512                          */
 513                         cmd->resp[0] = au_readl(host->iobase + SD_RESP0);
 514                 }
 515         }
 516
 517         /* Figure out errors */
 518
 519         if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC))
 520                 cmd->error = MMC_ERR_BADCRC;
 521
 522         trans = host->flags & (HOST_F_XMIT | HOST_F_RECV);
 523
 524         if (!trans || cmd->error != MMC_ERR_NONE) {
 525
 526                 IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF);
 527                 tasklet_schedule(&host->finish_task);
 528                 return;
 529         }
 530
 531         host->status = HOST_S_DATA;
 532
 533         if (host->flags & HOST_F_DMA) {
 534                 u32 channel = DMA_CHANNEL(host);
 535
 536                 /* Start the DMA as soon as the buffer gets something in it */
 537
 538                 if (host->flags & HOST_F_RECV) {
 539                         u32 mask = SD_STATUS_DB | SD_STATUS_NE;
 540
 541                         while((status & mask) != mask)
 542                                 status = au_readl(HOST_STATUS(host));
 543                 }
 544
 545                 au1xxx_dbdma_start(channel);
 546         }
 547 }
 548
 549 static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate)
 550 {
 551
 552         unsigned int pbus = get_au1x00_speed();
 553         unsigned int divisor;
 554         u32 config;
 555
 556         /* From databook:
 557            divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1
 558         */
 559
 560         pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2);
 561         pbus /= 2;
 562
 563         divisor = ((pbus / rate) / 2) - 1;
 564
 565         config = au_readl(HOST_CONFIG(host));
 566
 567         config &= ~(SD_CONFIG_DIV);
 568         config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;
 569
 570         au_writel(config, HOST_CONFIG(host));
 571         au_sync();
 572 }
 573
 574 static int
 575 au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data)
 576 {
 577
 578         int datalen = data->blocks * (1 << data->blksz_bits);
 579
 580         if (dma != 0)
 581                 host->flags |= HOST_F_DMA;
 582
 583         if (data->flags & MMC_DATA_READ)
 584                 host->flags |= HOST_F_RECV;
 585         else
 586                 host->flags |= HOST_F_XMIT;
 587
 588         if (host->mrq->stop)
 589                 host->flags |= HOST_F_STOP;
 590
 591         host->dma.dir = DMA_BIDIRECTIONAL;
 592
 593         host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg,
 594                                    data->sg_len, host->dma.dir);
 595
 596         if (host->dma.len == 0)
 597                 return MMC_ERR_TIMEOUT;
 598
 599         au_writel((1 << data->blksz_bits) - 1, HOST_BLKSIZE(host));
 600
 601         if (host->flags & HOST_F_DMA) {
 602                 int i;
 603                 u32 channel = DMA_CHANNEL(host);
 604
 605                 au1xxx_dbdma_stop(channel);
 606
 607                 for(i = 0; i < host->dma.len; i++) {
 608                         u32 ret = 0, flags = DDMA_FLAGS_NOIE;
 609                         struct scatterlist *sg = &data->sg[i];
 610                         int sg_len = sg->length;
 611
 612                         int len = (datalen > sg_len) ? sg_len : datalen;
 613
 614                         if (i == host->dma.len - 1)
 615                                 flags = DDMA_FLAGS_IE;
 616
 617                         if (host->flags & HOST_F_XMIT){
 618                                 ret = au1xxx_dbdma_put_source_flags(channel,
 619                                         (void *) (page_address(sg->page) +
 620                                                   sg->offset),
 621                                         len, flags);
 622                         }
 623                         else {
 624                                 ret = au1xxx_dbdma_put_dest_flags(channel,
 625                                         (void *) (page_address(sg->page) +
 626                                                   sg->offset),
 627                                         len, flags);
 628                         }
 629
 630                         if (!ret)
 631                                 goto dataerr;
 632
 633                         datalen -= len;
 634                 }
 635         }
 636         else {
 637                 host->pio.index = 0;
 638                 host->pio.offset = 0;
 639                 host->pio.len = datalen;
 640
 641                 if (host->flags & HOST_F_XMIT)
 642                         IRQ_ON(host, SD_CONFIG_TH);
 643                 else
 644                         IRQ_ON(host, SD_CONFIG_NE);
 645                         //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF);
 646         }
 647
 648         return MMC_ERR_NONE;
 649
 650  dataerr:
 651         dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir);
 652         return MMC_ERR_TIMEOUT;
 653 }
 654
 655 /* static void au1xmmc_request
 656    This actually starts a command or data transaction
 657 */
 658
 659 static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq)
 660 {
 661
 662         struct au1xmmc_host *host = mmc_priv(mmc);
 663         int ret = MMC_ERR_NONE;
 664
 665         WARN_ON(irqs_disabled());
 666         WARN_ON(host->status != HOST_S_IDLE);
 667
 668         host->mrq = mrq;
 669         host->status = HOST_S_CMD;
 670
 671         bcsr->disk_leds &= ~(1 << 8);
 672
 673         if (mrq->data) {
 674                 FLUSH_FIFO(host);
 675                 ret = au1xmmc_prepare_data(host, mrq->data);
 676         }
 677
 678         if (ret == MMC_ERR_NONE)
 679                 ret = au1xmmc_send_command(host, 0, mrq->cmd);
 680
 681         if (ret != MMC_ERR_NONE) {
 682                 mrq->cmd->error = ret;
 683                 au1xmmc_finish_request(host);
 684         }
 685 }
 686
 687 static void au1xmmc_reset_controller(struct au1xmmc_host *host)
 688 {
 689
 690         /* Apply the clock */
 691         au_writel(SD_ENABLE_CE, HOST_ENABLE(host));
 692         au_sync_delay(1);
 693
 694         au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
 695         au_sync_delay(5);
 696
 697         au_writel(~0, HOST_STATUS(host));
 698         au_sync();
 699
 700         au_writel(0, HOST_BLKSIZE(host));
 701         au_writel(0x001fffff, HOST_TIMEOUT(host));
 702         au_sync();
 703
 704         au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
 705         au_sync();
 706
 707         au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
 708         au_sync_delay(1);
 709
 710         au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
 711         au_sync();
 712
 713         /* Configure interrupts */
 714         au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
 715         au_sync();
 716 }
 717
 718
 719 static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios)
 720 {
 721         struct au1xmmc_host *host = mmc_priv(mmc);
 722
 723         DBG("set_ios (power=%u, clock=%uHz, vdd=%u, mode=%u)\n",
 724               host->id, ios->power_mode, ios->clock, ios->vdd,
 725               ios->bus_mode);
 726
 727         if (ios->power_mode == MMC_POWER_OFF)
 728                 au1xmmc_set_power(host, 0);
 729         else if (ios->power_mode == MMC_POWER_ON) {
 730                 au1xmmc_set_power(host, 1);
 731         }
 732
 733         if (ios->clock && ios->clock != host->clock) {
 734                 au1xmmc_set_clock(host, ios->clock);
 735                 host->clock = ios->clock;
 736         }
 737 }
 738
 739 static void au1xmmc_dma_callback(int irq, void *dev_id, struct pt_regs *regs)
 740 {
 741         struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id;
 742
 743         /* Avoid spurious interrupts */
 744
 745         if (!host->mrq)
 746                 return;
 747
 748         if (host->flags & HOST_F_STOP)
 749                 SEND_STOP(host);
 750
 751         tasklet_schedule(&host->data_task);
 752 }
 753
 754 #define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
 755 #define STATUS_DATA_IN  (SD_STATUS_NE)
 756 #define STATUS_DATA_OUT (SD_STATUS_TH)
 757
 758 static irqreturn_t au1xmmc_irq(int irq, void *dev_id, struct pt_regs *regs)
 759 {
 760
 761         u32 status;
 762         int i, ret = 0;
 763
 764         disable_irq(AU1100_SD_IRQ);
 765
 766         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 767                 struct au1xmmc_host * host = au1xmmc_hosts[i];
 768                 u32 handled = 1;
 769
 770                 status = au_readl(HOST_STATUS(host));
 771
 772                 if (host->mrq && (status & STATUS_TIMEOUT)) {
 773                         if (status & SD_STATUS_RAT)
 774                                 host->mrq->cmd->error = MMC_ERR_TIMEOUT;
 775
 776                         else if (status & SD_STATUS_DT)
 777                                 host->mrq->data->error = MMC_ERR_TIMEOUT;
 778
 779                         /* In PIO mode, interrupts might still be enabled */
 780                         IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH);
 781
 782                         //IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF);
 783                         tasklet_schedule(&host->finish_task);
 784                 }
 785 #if 0
 786                 else if (status & SD_STATUS_DD) {
 787
 788                         /* Sometimes we get a DD before a NE in PIO mode */
 789
 790                         if (!(host->flags & HOST_F_DMA) &&
 791                                         (status & SD_STATUS_NE))
 792                                 au1xmmc_receive_pio(host);
 793                         else {
 794                                 au1xmmc_data_complete(host, status);
 795                                 //tasklet_schedule(&host->data_task);
 796                         }
 797                 }
 798 #endif
 799                 else if (status & (SD_STATUS_CR)) {
 800                         if (host->status == HOST_S_CMD)
 801                                 au1xmmc_cmd_complete(host,status);
 802                 }
 803                 else if (!(host->flags & HOST_F_DMA)) {
 804                         if ((host->flags & HOST_F_XMIT) &&
 805                             (status & STATUS_DATA_OUT))
 806                                 au1xmmc_send_pio(host);
 807                         else if ((host->flags & HOST_F_RECV) &&
 808                             (status & STATUS_DATA_IN))
 809                                 au1xmmc_receive_pio(host);
 810                 }
 811                 else if (status & 0x203FBC70) {
 812                         DBG("Unhandled status %8.8x\n", host->id, status);
 813                         handled = 0;
 814                 }
 815
 816                 au_writel(status, HOST_STATUS(host));
 817                 au_sync();
 818
 819                 ret |= handled;
 820         }
 821
 822         enable_irq(AU1100_SD_IRQ);
 823         return ret;
 824 }
 825
 826 static void au1xmmc_poll_event(unsigned long arg)
 827 {
 828         struct au1xmmc_host *host = (struct au1xmmc_host *) arg;
 829
 830         int card = au1xmmc_card_inserted(host);
 831         int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0;
 832
 833         if (card != controller) {
 834                 host->flags &= ~HOST_F_ACTIVE;
 835                 if (card) host->flags |= HOST_F_ACTIVE;
 836                 mmc_detect_change(host->mmc, 0);
 837         }
 838
 839         if (host->mrq != NULL) {
 840                 u32 status = au_readl(HOST_STATUS(host));
 841                 DBG("PENDING - %8.8x\n", host->id, status);
 842         }
 843
 844         mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT);
 845 }
 846
 847 static dbdev_tab_t au1xmmc_mem_dbdev =
 848 {
 849         DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0
 850 };
 851
 852 static void au1xmmc_init_dma(struct au1xmmc_host *host)
 853 {
 854
 855         u32 rxchan, txchan;
 856
 857         int txid = au1xmmc_card_table[host->id].tx_devid;
 858         int rxid = au1xmmc_card_table[host->id].rx_devid;
 859
 860         /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride
 861            of 8 bits.  And since devices are shared, we need to create
 862            our own to avoid freaking out other devices
 863         */
 864
 865         int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev);
 866
 867         txchan = au1xxx_dbdma_chan_alloc(memid, txid,
 868                                          au1xmmc_dma_callback, (void *) host);
 869
 870         rxchan = au1xxx_dbdma_chan_alloc(rxid, memid,
 871                                          au1xmmc_dma_callback, (void *) host);
 872
 873         au1xxx_dbdma_set_devwidth(txchan, 8);
 874         au1xxx_dbdma_set_devwidth(rxchan, 8);
 875
 876         au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT);
 877         au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT);
 878
 879         host->tx_chan = txchan;
 880         host->rx_chan = rxchan;
 881 }
 882
 883 struct mmc_host_ops au1xmmc_ops = {
 884         .request        = au1xmmc_request,
 885         .set_ios        = au1xmmc_set_ios,
 886 };
 887
 888 static int __devinit au1xmmc_probe(struct platform_device *pdev)
 889 {
 890
 891         int i, ret = 0;
 892
 893         /* THe interrupt is shared among all controllers */
 894         ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, SA_INTERRUPT, "MMC", 0);
 895
 896         if (ret) {
 897                 printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n",
 898                                 AU1100_SD_IRQ, ret);
 899                 return -ENXIO;
 900         }
 901
 902         disable_irq(AU1100_SD_IRQ);
 903
 904         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 905                 struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
 906                 struct au1xmmc_host *host = 0;
 907
 908                 if (!mmc) {
 909                         printk(DRIVER_NAME "ERROR: no mem for host %d\n", i);
 910                         au1xmmc_hosts[i] = 0;
 911                         continue;
 912                 }
 913
 914                 mmc->ops = &au1xmmc_ops;
 915
 916                 mmc->f_min =   450000;
 917                 mmc->f_max = 24000000;
 918
 919                 mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE;
 920                 mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT;
 921
 922                 mmc->ocr_avail = AU1XMMC_OCR;
 923
 924                 host = mmc_priv(mmc);
 925                 host->mmc = mmc;
 926
 927                 host->id = i;
 928                 host->iobase = au1xmmc_card_table[host->id].iobase;
 929                 host->clock = 0;
 930                 host->power_mode = MMC_POWER_OFF;
 931
 932                 host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0;
 933                 host->status = HOST_S_IDLE;
 934
 935                 init_timer(&host->timer);
 936
 937                 host->timer.function = au1xmmc_poll_event;
 938                 host->timer.data = (unsigned long) host;
 939                 host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT;
 940
 941                 tasklet_init(&host->data_task, au1xmmc_tasklet_data,
 942                                 (unsigned long) host);
 943
 944                 tasklet_init(&host->finish_task, au1xmmc_tasklet_finish,
 945                                 (unsigned long) host);
 946
 947                 spin_lock_init(&host->lock);
 948
 949                 if (dma != 0)
 950                         au1xmmc_init_dma(host);
 951
 952                 au1xmmc_reset_controller(host);
 953
 954                 mmc_add_host(mmc);
 955                 au1xmmc_hosts[i] = host;
 956
 957                 add_timer(&host->timer);
 958
 959                 printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n",
 960                        host->id, host->iobase, dma ? "dma" : "pio");
 961         }
 962
 963         enable_irq(AU1100_SD_IRQ);
 964
 965         return 0;
 966 }
 967
 968 static int __devexit au1xmmc_remove(struct platform_device *pdev)
 969 {
 970
 971         int i;
 972
 973         disable_irq(AU1100_SD_IRQ);
 974
 975         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 976                 struct au1xmmc_host *host = au1xmmc_hosts[i];
 977                 if (!host) continue;
 978
 979                 tasklet_kill(&host->data_task);
 980                 tasklet_kill(&host->finish_task);
 981
 982                 del_timer_sync(&host->timer);
 983                 au1xmmc_set_power(host, 0);
 984
 985                 mmc_remove_host(host->mmc);
 986
 987                 au1xxx_dbdma_chan_free(host->tx_chan);
 988                 au1xxx_dbdma_chan_free(host->rx_chan);
 989
 990                 au_writel(0x0, HOST_ENABLE(host));
 991                 au_sync();
 992         }
 993
 994         free_irq(AU1100_SD_IRQ, 0);
 995         return 0;
 996 }
 997
 998 static struct platform_driver au1xmmc_driver = {
 999         .probe         = au1xmmc_probe,
1000         .remove        = au1xmmc_remove,
1001         .suspend       = NULL,
1002         .resume        = NULL,
1003         .driver        = {
1004                 .name  = DRIVER_NAME,
1005         },
1006 };
1007
1008 static int __init au1xmmc_init(void)
1009 {
1010         return platform_driver_register(&au1xmmc_driver);
1011 }
1012
1013 static void __exit au1xmmc_exit(void)
1014 {
1015         platform_driver_unregister(&au1xmmc_driver);
1016 }
1017
1018 module_init(au1xmmc_init);
1019 module_exit(au1xmmc_exit);
1020
1021 #ifdef MODULE
1022 MODULE_AUTHOR("Advanced Micro Devices, Inc");
1023 MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX");
1024 MODULE_LICENSE("GPL");
1025 #endif
1026