IB/ipath: Add code to support multiple link speeds and widths
[safe/jmp/linux-2.6] / drivers / infiniband / hw / ipath / ipath_kernel.h
1 #ifndef _IPATH_KERNEL_H
2 #define _IPATH_KERNEL_H
3 /*
4  * Copyright (c) 2006, 2007 QLogic Corporation. All rights reserved.
5  * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
6  *
7  * This software is available to you under a choice of one of two
8  * licenses.  You may choose to be licensed under the terms of the GNU
9  * General Public License (GPL) Version 2, available from the file
10  * COPYING in the main directory of this source tree, or the
11  * OpenIB.org BSD license below:
12  *
13  *     Redistribution and use in source and binary forms, with or
14  *     without modification, are permitted provided that the following
15  *     conditions are met:
16  *
17  *      - Redistributions of source code must retain the above
18  *        copyright notice, this list of conditions and the following
19  *        disclaimer.
20  *
21  *      - Redistributions in binary form must reproduce the above
22  *        copyright notice, this list of conditions and the following
23  *        disclaimer in the documentation and/or other materials
24  *        provided with the distribution.
25  *
26  * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
27  * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
28  * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
29  * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
30  * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
31  * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
32  * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
33  * SOFTWARE.
34  */
35
36 /*
37  * This header file is the base header file for infinipath kernel code
38  * ipath_user.h serves a similar purpose for user code.
39  */
40
41 #include <linux/interrupt.h>
42 #include <linux/pci.h>
43 #include <linux/dma-mapping.h>
44 #include <linux/mutex.h>
45 #include <asm/io.h>
46 #include <rdma/ib_verbs.h>
47
48 #include "ipath_common.h"
49 #include "ipath_debug.h"
50 #include "ipath_registers.h"
51
52 /* only s/w major version of InfiniPath we can handle */
53 #define IPATH_CHIP_VERS_MAJ 2U
54
55 /* don't care about this except printing */
56 #define IPATH_CHIP_VERS_MIN 0U
57
58 /* temporary, maybe always */
59 extern struct infinipath_stats ipath_stats;
60
61 #define IPATH_CHIP_SWVERSION IPATH_CHIP_VERS_MAJ
62 /*
63  * First-cut critierion for "device is active" is
64  * two thousand dwords combined Tx, Rx traffic per
65  * 5-second interval. SMA packets are 64 dwords,
66  * and occur "a few per second", presumably each way.
67  */
68 #define IPATH_TRAFFIC_ACTIVE_THRESHOLD (2000)
69 /*
70  * Struct used to indicate which errors are logged in each of the
71  * error-counters that are logged to EEPROM. A counter is incremented
72  * _once_ (saturating at 255) for each event with any bits set in
73  * the error or hwerror register masks below.
74  */
75 #define IPATH_EEP_LOG_CNT (4)
76 struct ipath_eep_log_mask {
77         u64 errs_to_log;
78         u64 hwerrs_to_log;
79 };
80
81 struct ipath_portdata {
82         void **port_rcvegrbuf;
83         dma_addr_t *port_rcvegrbuf_phys;
84         /* rcvhdrq base, needs mmap before useful */
85         void *port_rcvhdrq;
86         /* kernel virtual address where hdrqtail is updated */
87         void *port_rcvhdrtail_kvaddr;
88         /*
89          * temp buffer for expected send setup, allocated at open, instead
90          * of each setup call
91          */
92         void *port_tid_pg_list;
93         /* when waiting for rcv or pioavail */
94         wait_queue_head_t port_wait;
95         /*
96          * rcvegr bufs base, physical, must fit
97          * in 44 bits so 32 bit programs mmap64 44 bit works)
98          */
99         dma_addr_t port_rcvegr_phys;
100         /* mmap of hdrq, must fit in 44 bits */
101         dma_addr_t port_rcvhdrq_phys;
102         dma_addr_t port_rcvhdrqtailaddr_phys;
103         /*
104          * number of opens (including slave subports) on this instance
105          * (ignoring forks, dup, etc. for now)
106          */
107         int port_cnt;
108         /*
109          * how much space to leave at start of eager TID entries for
110          * protocol use, on each TID
111          */
112         /* instead of calculating it */
113         unsigned port_port;
114         /* non-zero if port is being shared. */
115         u16 port_subport_cnt;
116         /* non-zero if port is being shared. */
117         u16 port_subport_id;
118         /* chip offset of PIO buffers for this port */
119         u32 port_piobufs;
120         /* how many alloc_pages() chunks in port_rcvegrbuf_pages */
121         u32 port_rcvegrbuf_chunks;
122         /* how many egrbufs per chunk */
123         u32 port_rcvegrbufs_perchunk;
124         /* order for port_rcvegrbuf_pages */
125         size_t port_rcvegrbuf_size;
126         /* rcvhdrq size (for freeing) */
127         size_t port_rcvhdrq_size;
128         /* next expected TID to check when looking for free */
129         u32 port_tidcursor;
130         /* next expected TID to check */
131         unsigned long port_flag;
132         /* what happened */
133         unsigned long int_flag;
134         /* WAIT_RCV that timed out, no interrupt */
135         u32 port_rcvwait_to;
136         /* WAIT_PIO that timed out, no interrupt */
137         u32 port_piowait_to;
138         /* WAIT_RCV already happened, no wait */
139         u32 port_rcvnowait;
140         /* WAIT_PIO already happened, no wait */
141         u32 port_pionowait;
142         /* total number of rcvhdrqfull errors */
143         u32 port_hdrqfull;
144         /*
145          * Used to suppress multiple instances of same
146          * port staying stuck at same point.
147          */
148         u32 port_lastrcvhdrqtail;
149         /* saved total number of rcvhdrqfull errors for poll edge trigger */
150         u32 port_hdrqfull_poll;
151         /* total number of polled urgent packets */
152         u32 port_urgent;
153         /* saved total number of polled urgent packets for poll edge trigger */
154         u32 port_urgent_poll;
155         /* pid of process using this port */
156         pid_t port_pid;
157         pid_t port_subpid[INFINIPATH_MAX_SUBPORT];
158         /* same size as task_struct .comm[] */
159         char port_comm[16];
160         /* pkeys set by this use of this port */
161         u16 port_pkeys[4];
162         /* so file ops can get at unit */
163         struct ipath_devdata *port_dd;
164         /* A page of memory for rcvhdrhead, rcvegrhead, rcvegrtail * N */
165         void *subport_uregbase;
166         /* An array of pages for the eager receive buffers * N */
167         void *subport_rcvegrbuf;
168         /* An array of pages for the eager header queue entries * N */
169         void *subport_rcvhdr_base;
170         /* The version of the library which opened this port */
171         u32 userversion;
172         /* Bitmask of active slaves */
173         u32 active_slaves;
174         /* Type of packets or conditions we want to poll for */
175         u16 poll_type;
176         /* port rcvhdrq head offset */
177         u32 port_head;
178 };
179
180 struct sk_buff;
181
182 /*
183  * control information for layered drivers
184  */
185 struct _ipath_layer {
186         void *l_arg;
187 };
188
189 struct ipath_skbinfo {
190         struct sk_buff *skb;
191         dma_addr_t phys;
192 };
193
194 /*
195  * Possible IB config parameters for ipath_f_get/set_ib_cfg()
196  */
197 #define IPATH_IB_CFG_LIDLMC 0 /* Get/set LID (LS16b) and Mask (MS16b) */
198 #define IPATH_IB_CFG_HRTBT 1 /* Get/set Heartbeat off/enable/auto */
199 #define IPATH_IB_HRTBT_ON 3 /* Heartbeat enabled, sent every 100msec */
200 #define IPATH_IB_HRTBT_OFF 0 /* Heartbeat off */
201 #define IPATH_IB_CFG_LWID_ENB 2 /* Get/set allowed Link-width */
202 #define IPATH_IB_CFG_LWID 3 /* Get currently active Link-width */
203 #define IPATH_IB_CFG_SPD_ENB 4 /* Get/set allowed Link speeds */
204 #define IPATH_IB_CFG_SPD 5 /* Get current Link spd */
205 #define IPATH_IB_CFG_RXPOL_ENB 6 /* Get/set Auto-RX-polarity enable */
206 #define IPATH_IB_CFG_LREV_ENB 7 /* Get/set Auto-Lane-reversal enable */
207 #define IPATH_IB_CFG_LINKLATENCY 8 /* Get Auto-Lane-reversal enable */
208
209
210 struct ipath_devdata {
211         struct list_head ipath_list;
212
213         struct ipath_kregs const *ipath_kregs;
214         struct ipath_cregs const *ipath_cregs;
215
216         /* mem-mapped pointer to base of chip regs */
217         u64 __iomem *ipath_kregbase;
218         /* end of mem-mapped chip space; range checking */
219         u64 __iomem *ipath_kregend;
220         /* physical address of chip for io_remap, etc. */
221         unsigned long ipath_physaddr;
222         /* base of memory alloced for ipath_kregbase, for free */
223         u64 *ipath_kregalloc;
224         /*
225          * virtual address where port0 rcvhdrqtail updated for this unit.
226          * only written to by the chip, not the driver.
227          */
228         volatile __le64 *ipath_hdrqtailptr;
229         /* ipath_cfgports pointers */
230         struct ipath_portdata **ipath_pd;
231         /* sk_buffs used by port 0 eager receive queue */
232         struct ipath_skbinfo *ipath_port0_skbinfo;
233         /* kvirt address of 1st 2k pio buffer */
234         void __iomem *ipath_pio2kbase;
235         /* kvirt address of 1st 4k pio buffer */
236         void __iomem *ipath_pio4kbase;
237         /*
238          * points to area where PIOavail registers will be DMA'ed.
239          * Has to be on a page of it's own, because the page will be
240          * mapped into user program space.  This copy is *ONLY* ever
241          * written by DMA, not by the driver!  Need a copy per device
242          * when we get to multiple devices
243          */
244         volatile __le64 *ipath_pioavailregs_dma;
245         /* physical address where updates occur */
246         dma_addr_t ipath_pioavailregs_phys;
247         struct _ipath_layer ipath_layer;
248         /* setup intr */
249         int (*ipath_f_intrsetup)(struct ipath_devdata *);
250         /* fallback to alternate interrupt type if possible */
251         int (*ipath_f_intr_fallback)(struct ipath_devdata *);
252         /* setup on-chip bus config */
253         int (*ipath_f_bus)(struct ipath_devdata *, struct pci_dev *);
254         /* hard reset chip */
255         int (*ipath_f_reset)(struct ipath_devdata *);
256         int (*ipath_f_get_boardname)(struct ipath_devdata *, char *,
257                                      size_t);
258         void (*ipath_f_init_hwerrors)(struct ipath_devdata *);
259         void (*ipath_f_handle_hwerrors)(struct ipath_devdata *, char *,
260                                         size_t);
261         void (*ipath_f_quiet_serdes)(struct ipath_devdata *);
262         int (*ipath_f_bringup_serdes)(struct ipath_devdata *);
263         int (*ipath_f_early_init)(struct ipath_devdata *);
264         void (*ipath_f_clear_tids)(struct ipath_devdata *, unsigned);
265         void (*ipath_f_put_tid)(struct ipath_devdata *, u64 __iomem*,
266                                 u32, unsigned long);
267         void (*ipath_f_tidtemplate)(struct ipath_devdata *);
268         void (*ipath_f_cleanup)(struct ipath_devdata *);
269         void (*ipath_f_setextled)(struct ipath_devdata *, u64, u64);
270         /* fill out chip-specific fields */
271         int (*ipath_f_get_base_info)(struct ipath_portdata *, void *);
272         /* free irq */
273         void (*ipath_f_free_irq)(struct ipath_devdata *);
274         struct ipath_message_header *(*ipath_f_get_msgheader)
275                                         (struct ipath_devdata *, __le32 *);
276         void (*ipath_f_config_ports)(struct ipath_devdata *, ushort);
277         int (*ipath_f_get_ib_cfg)(struct ipath_devdata *, int);
278         int (*ipath_f_set_ib_cfg)(struct ipath_devdata *, int, u32);
279         void (*ipath_f_config_jint)(struct ipath_devdata *, u16 , u16);
280         void (*ipath_f_read_counters)(struct ipath_devdata *,
281                                         struct infinipath_counters *);
282         void (*ipath_f_xgxs_reset)(struct ipath_devdata *);
283         /* per chip actions needed for IB Link up/down changes */
284         int (*ipath_f_ib_updown)(struct ipath_devdata *, int, u64);
285
286         struct ipath_ibdev *verbs_dev;
287         struct timer_list verbs_timer;
288         /* total dwords sent (summed from counter) */
289         u64 ipath_sword;
290         /* total dwords rcvd (summed from counter) */
291         u64 ipath_rword;
292         /* total packets sent (summed from counter) */
293         u64 ipath_spkts;
294         /* total packets rcvd (summed from counter) */
295         u64 ipath_rpkts;
296         /* ipath_statusp initially points to this. */
297         u64 _ipath_status;
298         /* GUID for this interface, in network order */
299         __be64 ipath_guid;
300         /*
301          * aggregrate of error bits reported since last cleared, for
302          * limiting of error reporting
303          */
304         ipath_err_t ipath_lasterror;
305         /*
306          * aggregrate of error bits reported since last cleared, for
307          * limiting of hwerror reporting
308          */
309         ipath_err_t ipath_lasthwerror;
310         /* errors masked because they occur too fast */
311         ipath_err_t ipath_maskederrs;
312         /* time in jiffies at which to re-enable maskederrs */
313         unsigned long ipath_unmasktime;
314         /* count of egrfull errors, combined for all ports */
315         u64 ipath_last_tidfull;
316         /* for ipath_qcheck() */
317         u64 ipath_lastport0rcv_cnt;
318         /* template for writing TIDs  */
319         u64 ipath_tidtemplate;
320         /* value to write to free TIDs */
321         u64 ipath_tidinvalid;
322         /* IBA6120 rcv interrupt setup */
323         u64 ipath_rhdrhead_intr_off;
324
325         /* size of memory at ipath_kregbase */
326         u32 ipath_kregsize;
327         /* number of registers used for pioavail */
328         u32 ipath_pioavregs;
329         /* IPATH_POLL, etc. */
330         u32 ipath_flags;
331         /* ipath_flags driver is waiting for */
332         u32 ipath_state_wanted;
333         /* last buffer for user use, first buf for kernel use is this
334          * index. */
335         u32 ipath_lastport_piobuf;
336         /* is a stats timer active */
337         u32 ipath_stats_timer_active;
338         /* number of interrupts for this device -- saturates... */
339         u32 ipath_int_counter;
340         /* dwords sent read from counter */
341         u32 ipath_lastsword;
342         /* dwords received read from counter */
343         u32 ipath_lastrword;
344         /* sent packets read from counter */
345         u32 ipath_lastspkts;
346         /* received packets read from counter */
347         u32 ipath_lastrpkts;
348         /* pio bufs allocated per port */
349         u32 ipath_pbufsport;
350         /*
351          * number of ports configured as max; zero is set to number chip
352          * supports, less gives more pio bufs/port, etc.
353          */
354         u32 ipath_cfgports;
355         /* count of port 0 hdrqfull errors */
356         u32 ipath_p0_hdrqfull;
357         /* port 0 number of receive eager buffers */
358         u32 ipath_p0_rcvegrcnt;
359
360         /*
361          * index of last piobuffer we used.  Speeds up searching, by
362          * starting at this point.  Doesn't matter if multiple cpu's use and
363          * update, last updater is only write that matters.  Whenever it
364          * wraps, we update shadow copies.  Need a copy per device when we
365          * get to multiple devices
366          */
367         u32 ipath_lastpioindex;
368         /* max length of freezemsg */
369         u32 ipath_freezelen;
370         /*
371          * consecutive times we wanted a PIO buffer but were unable to
372          * get one
373          */
374         u32 ipath_consec_nopiobuf;
375         /*
376          * hint that we should update ipath_pioavailshadow before
377          * looking for a PIO buffer
378          */
379         u32 ipath_upd_pio_shadow;
380         /* so we can rewrite it after a chip reset */
381         u32 ipath_pcibar0;
382         /* so we can rewrite it after a chip reset */
383         u32 ipath_pcibar1;
384
385         /* interrupt number */
386         int ipath_irq;
387         /* HT/PCI Vendor ID (here for NodeInfo) */
388         u16 ipath_vendorid;
389         /* HT/PCI Device ID (here for NodeInfo) */
390         u16 ipath_deviceid;
391         /* offset in HT config space of slave/primary interface block */
392         u8 ipath_ht_slave_off;
393         /* for write combining settings */
394         unsigned long ipath_wc_cookie;
395         unsigned long ipath_wc_base;
396         unsigned long ipath_wc_len;
397         /* ref count for each pkey */
398         atomic_t ipath_pkeyrefs[4];
399         /* shadow copy of struct page *'s for exp tid pages */
400         struct page **ipath_pageshadow;
401         /* shadow copy of dma handles for exp tid pages */
402         dma_addr_t *ipath_physshadow;
403         u64 __iomem *ipath_egrtidbase;
404         /* lock to workaround chip bug 9437 and others */
405         spinlock_t ipath_kernel_tid_lock;
406         spinlock_t ipath_tid_lock;
407         spinlock_t ipath_sendctrl_lock;
408
409         /*
410          * IPATH_STATUS_*,
411          * this address is mapped readonly into user processes so they can
412          * get status cheaply, whenever they want.
413          */
414         u64 *ipath_statusp;
415         /* freeze msg if hw error put chip in freeze */
416         char *ipath_freezemsg;
417         /* pci access data structure */
418         struct pci_dev *pcidev;
419         struct cdev *user_cdev;
420         struct cdev *diag_cdev;
421         struct class_device *user_class_dev;
422         struct class_device *diag_class_dev;
423         /* timer used to prevent stats overflow, error throttling, etc. */
424         struct timer_list ipath_stats_timer;
425         void *ipath_dummy_hdrq; /* used after port close */
426         dma_addr_t ipath_dummy_hdrq_phys;
427
428         unsigned long ipath_ureg_align; /* user register alignment */
429
430         /* HoL blocking / user app forward-progress state */
431         unsigned          ipath_hol_state;
432         unsigned          ipath_hol_next;
433         struct timer_list ipath_hol_timer;
434
435         /*
436          * Shadow copies of registers; size indicates read access size.
437          * Most of them are readonly, but some are write-only register,
438          * where we manipulate the bits in the shadow copy, and then write
439          * the shadow copy to infinipath.
440          *
441          * We deliberately make most of these 32 bits, since they have
442          * restricted range.  For any that we read, we won't to generate 32
443          * bit accesses, since Opteron will generate 2 separate 32 bit HT
444          * transactions for a 64 bit read, and we want to avoid unnecessary
445          * HT transactions.
446          */
447
448         /* This is the 64 bit group */
449
450         /*
451          * shadow of pioavail, check to be sure it's large enough at
452          * init time.
453          */
454         unsigned long ipath_pioavailshadow[8];
455         /* shadow of kr_gpio_out, for rmw ops */
456         u64 ipath_gpio_out;
457         /* shadow the gpio mask register */
458         u64 ipath_gpio_mask;
459         /* shadow the gpio output enable, etc... */
460         u64 ipath_extctrl;
461         /* kr_revision shadow */
462         u64 ipath_revision;
463         /*
464          * shadow of ibcctrl, for interrupt handling of link changes,
465          * etc.
466          */
467         u64 ipath_ibcctrl;
468         /*
469          * last ibcstatus, to suppress "duplicate" status change messages,
470          * mostly from 2 to 3
471          */
472         u64 ipath_lastibcstat;
473         /* hwerrmask shadow */
474         ipath_err_t ipath_hwerrmask;
475         ipath_err_t ipath_errormask; /* errormask shadow */
476         /* interrupt config reg shadow */
477         u64 ipath_intconfig;
478         /* kr_sendpiobufbase value */
479         u64 ipath_piobufbase;
480
481         /* these are the "32 bit" regs */
482
483         /*
484          * number of GUIDs in the flash for this interface; may need some
485          * rethinking for setting on other ifaces
486          */
487         u32 ipath_nguid;
488         /*
489          * the following two are 32-bit bitmasks, but {test,clear,set}_bit
490          * all expect bit fields to be "unsigned long"
491          */
492         /* shadow kr_rcvctrl */
493         unsigned long ipath_rcvctrl;
494         /* shadow kr_sendctrl */
495         unsigned long ipath_sendctrl;
496         unsigned long ipath_lastcancel; /* to not count armlaunch after cancel */
497
498         /* value we put in kr_rcvhdrcnt */
499         u32 ipath_rcvhdrcnt;
500         /* value we put in kr_rcvhdrsize */
501         u32 ipath_rcvhdrsize;
502         /* value we put in kr_rcvhdrentsize */
503         u32 ipath_rcvhdrentsize;
504         /* offset of last entry in rcvhdrq */
505         u32 ipath_hdrqlast;
506         /* kr_portcnt value */
507         u32 ipath_portcnt;
508         /* kr_pagealign value */
509         u32 ipath_palign;
510         /* number of "2KB" PIO buffers */
511         u32 ipath_piobcnt2k;
512         /* size in bytes of "2KB" PIO buffers */
513         u32 ipath_piosize2k;
514         /* number of "4KB" PIO buffers */
515         u32 ipath_piobcnt4k;
516         /* size in bytes of "4KB" PIO buffers */
517         u32 ipath_piosize4k;
518         /* kr_rcvegrbase value */
519         u32 ipath_rcvegrbase;
520         /* kr_rcvegrcnt value */
521         u32 ipath_rcvegrcnt;
522         /* kr_rcvtidbase value */
523         u32 ipath_rcvtidbase;
524         /* kr_rcvtidcnt value */
525         u32 ipath_rcvtidcnt;
526         /* kr_sendregbase */
527         u32 ipath_sregbase;
528         /* kr_userregbase */
529         u32 ipath_uregbase;
530         /* kr_counterregbase */
531         u32 ipath_cregbase;
532         /* shadow the control register contents */
533         u32 ipath_control;
534         /* PCI revision register (HTC rev on FPGA) */
535         u32 ipath_pcirev;
536
537         /* chip address space used by 4k pio buffers */
538         u32 ipath_4kalign;
539         /* The MTU programmed for this unit */
540         u32 ipath_ibmtu;
541         /*
542          * The max size IB packet, included IB headers that we can send.
543          * Starts same as ipath_piosize, but is affected when ibmtu is
544          * changed, or by size of eager buffers
545          */
546         u32 ipath_ibmaxlen;
547         /*
548          * ibmaxlen at init time, limited by chip and by receive buffer
549          * size.  Not changed after init.
550          */
551         u32 ipath_init_ibmaxlen;
552         /* size of each rcvegrbuffer */
553         u32 ipath_rcvegrbufsize;
554         /* localbus width (1, 2,4,8,16,32) from config space  */
555         u32 ipath_lbus_width;
556         /* localbus speed (HT: 200,400,800,1000; PCIe 2500) */
557         u32 ipath_lbus_speed;
558         /*
559          * number of sequential ibcstatus change for polling active/quiet
560          * (i.e., link not coming up).
561          */
562         u32 ipath_ibpollcnt;
563         /* low and high portions of MSI capability/vector */
564         u32 ipath_msi_lo;
565         /* saved after PCIe init for restore after reset */
566         u32 ipath_msi_hi;
567         /* MSI data (vector) saved for restore */
568         u16 ipath_msi_data;
569         /* MLID programmed for this instance */
570         u16 ipath_mlid;
571         /* LID programmed for this instance */
572         u16 ipath_lid;
573         /* list of pkeys programmed; 0 if not set */
574         u16 ipath_pkeys[4];
575         /*
576          * ASCII serial number, from flash, large enough for original
577          * all digit strings, and longer QLogic serial number format
578          */
579         u8 ipath_serial[16];
580         /* human readable board version */
581         u8 ipath_boardversion[80];
582         u8 ipath_lbus_info[32]; /* human readable localbus info */
583         /* chip major rev, from ipath_revision */
584         u8 ipath_majrev;
585         /* chip minor rev, from ipath_revision */
586         u8 ipath_minrev;
587         /* board rev, from ipath_revision */
588         u8 ipath_boardrev;
589
590         u8 ipath_r_portenable_shift;
591         u8 ipath_r_intravail_shift;
592         u8 ipath_r_tailupd_shift;
593         u8 ipath_r_portcfg_shift;
594
595         /* unit # of this chip, if present */
596         int ipath_unit;
597         /* saved for restore after reset */
598         u8 ipath_pci_cacheline;
599         /* LID mask control */
600         u8 ipath_lmc;
601         /* link width supported */
602         u8 ipath_link_width_supported;
603         /* link speed supported */
604         u8 ipath_link_speed_supported;
605         u8 ipath_link_width_enabled;
606         u8 ipath_link_speed_enabled;
607         u8 ipath_link_width_active;
608         u8 ipath_link_speed_active;
609         /* Rx Polarity inversion (compensate for ~tx on partner) */
610         u8 ipath_rx_pol_inv;
611
612         /* local link integrity counter */
613         u32 ipath_lli_counter;
614         /* local link integrity errors */
615         u32 ipath_lli_errors;
616         /*
617          * Above counts only cases where _successive_ LocalLinkIntegrity
618          * errors were seen in the receive headers of kern-packets.
619          * Below are the three (monotonically increasing) counters
620          * maintained via GPIO interrupts on iba6120-rev2.
621          */
622         u32 ipath_rxfc_unsupvl_errs;
623         u32 ipath_overrun_thresh_errs;
624         u32 ipath_lli_errs;
625
626         /* status check work */
627         struct delayed_work status_work;
628
629         /*
630          * Not all devices managed by a driver instance are the same
631          * type, so these fields must be per-device.
632          */
633         u64 ipath_i_bitsextant;
634         ipath_err_t ipath_e_bitsextant;
635         ipath_err_t ipath_hwe_bitsextant;
636
637         /*
638          * Below should be computable from number of ports,
639          * since they are never modified.
640          */
641         u32 ipath_i_rcvavail_mask;
642         u32 ipath_i_rcvurg_mask;
643         u16 ipath_i_rcvurg_shift;
644         u16 ipath_i_rcvavail_shift;
645
646         /*
647          * Register bits for selecting i2c direction and values, used for
648          * I2C serial flash.
649          */
650         u16 ipath_gpio_sda_num;
651         u16 ipath_gpio_scl_num;
652         u64 ipath_gpio_sda;
653         u64 ipath_gpio_scl;
654
655         /* lock for doing RMW of shadows/regs for ExtCtrl and GPIO */
656         spinlock_t ipath_gpio_lock;
657
658         /*
659          * IB link and linktraining states and masks that vary per chip in
660          * some way.  Set at init, to avoid each IB status change interrupt
661          */
662         u8 ibcs_ls_shift;
663         u8 ibcs_lts_mask;
664         u32 ibcs_mask;
665         u32 ib_init;
666         u32 ib_arm;
667         u32 ib_active;
668
669         u16 ipath_rhf_offset; /* offset of RHF within receive header entry */
670
671         /*
672          * shift/mask for linkcmd, linkinitcmd, maxpktlen in ibccontol
673          * reg. Changes for IBA7220
674          */
675         u8 ibcc_lic_mask; /* LinkInitCmd */
676         u8 ibcc_lc_shift; /* LinkCmd */
677         u8 ibcc_mpl_shift; /* Maxpktlen */
678
679         u8 delay_mult;
680
681         /* used to override LED behavior */
682         u8 ipath_led_override;  /* Substituted for normal value, if non-zero */
683         u16 ipath_led_override_timeoff; /* delta to next timer event */
684         u8 ipath_led_override_vals[2]; /* Alternates per blink-frame */
685         u8 ipath_led_override_phase; /* Just counts, LSB picks from vals[] */
686         atomic_t ipath_led_override_timer_active;
687         /* Used to flash LEDs in override mode */
688         struct timer_list ipath_led_override_timer;
689
690         /* Support (including locks) for EEPROM logging of errors and time */
691         /* control access to actual counters, timer */
692         spinlock_t ipath_eep_st_lock;
693         /* control high-level access to EEPROM */
694         struct mutex ipath_eep_lock;
695         /* Below inc'd by ipath_snap_cntrs(), locked by ipath_eep_st_lock */
696         uint64_t ipath_traffic_wds;
697         /* active time is kept in seconds, but logged in hours */
698         atomic_t ipath_active_time;
699         /* Below are nominal shadow of EEPROM, new since last EEPROM update */
700         uint8_t ipath_eep_st_errs[IPATH_EEP_LOG_CNT];
701         uint8_t ipath_eep_st_new_errs[IPATH_EEP_LOG_CNT];
702         uint16_t ipath_eep_hrs;
703         /*
704          * masks for which bits of errs, hwerrs that cause
705          * each of the counters to increment.
706          */
707         struct ipath_eep_log_mask ipath_eep_st_masks[IPATH_EEP_LOG_CNT];
708
709         /* interrupt mitigation reload register info */
710         u16 ipath_jint_idle_ticks;      /* idle clock ticks */
711         u16 ipath_jint_max_packets;     /* max packets across all ports */
712 };
713
714 /* ipath_hol_state values (stopping/starting user proc, send flushing) */
715 #define IPATH_HOL_UP       0
716 #define IPATH_HOL_DOWN     1
717 /* ipath_hol_next toggle values, used when hol_state IPATH_HOL_DOWN */
718 #define IPATH_HOL_DOWNSTOP 0
719 #define IPATH_HOL_DOWNCONT 1
720
721 /* Private data for file operations */
722 struct ipath_filedata {
723         struct ipath_portdata *pd;
724         unsigned subport;
725         unsigned tidcursor;
726 };
727 extern struct list_head ipath_dev_list;
728 extern spinlock_t ipath_devs_lock;
729 extern struct ipath_devdata *ipath_lookup(int unit);
730
731 int ipath_init_chip(struct ipath_devdata *, int);
732 int ipath_enable_wc(struct ipath_devdata *dd);
733 void ipath_disable_wc(struct ipath_devdata *dd);
734 int ipath_count_units(int *npresentp, int *nupp, int *maxportsp);
735 void ipath_shutdown_device(struct ipath_devdata *);
736 void ipath_clear_freeze(struct ipath_devdata *);
737
738 struct file_operations;
739 int ipath_cdev_init(int minor, char *name, const struct file_operations *fops,
740                     struct cdev **cdevp, struct class_device **class_devp);
741 void ipath_cdev_cleanup(struct cdev **cdevp,
742                         struct class_device **class_devp);
743
744 int ipath_diag_add(struct ipath_devdata *);
745 void ipath_diag_remove(struct ipath_devdata *);
746
747 extern wait_queue_head_t ipath_state_wait;
748
749 int ipath_user_add(struct ipath_devdata *dd);
750 void ipath_user_remove(struct ipath_devdata *dd);
751
752 struct sk_buff *ipath_alloc_skb(struct ipath_devdata *dd, gfp_t);
753
754 extern int ipath_diag_inuse;
755
756 irqreturn_t ipath_intr(int irq, void *devid);
757 int ipath_decode_err(char *buf, size_t blen, ipath_err_t err);
758 #if __IPATH_INFO || __IPATH_DBG
759 extern const char *ipath_ibcstatus_str[];
760 #endif
761
762 /* clean up any per-chip chip-specific stuff */
763 void ipath_chip_cleanup(struct ipath_devdata *);
764 /* clean up any chip type-specific stuff */
765 void ipath_chip_done(void);
766
767 /* check to see if we have to force ordering for write combining */
768 int ipath_unordered_wc(void);
769
770 void ipath_disarm_piobufs(struct ipath_devdata *, unsigned first,
771                           unsigned cnt);
772 void ipath_cancel_sends(struct ipath_devdata *, int);
773
774 int ipath_create_rcvhdrq(struct ipath_devdata *, struct ipath_portdata *);
775 void ipath_free_pddata(struct ipath_devdata *, struct ipath_portdata *);
776
777 int ipath_parse_ushort(const char *str, unsigned short *valp);
778
779 void ipath_kreceive(struct ipath_portdata *);
780 int ipath_setrcvhdrsize(struct ipath_devdata *, unsigned);
781 int ipath_reset_device(int);
782 void ipath_get_faststats(unsigned long);
783 int ipath_wait_linkstate(struct ipath_devdata *, u32, int);
784 int ipath_set_linkstate(struct ipath_devdata *, u8);
785 int ipath_set_mtu(struct ipath_devdata *, u16);
786 int ipath_set_lid(struct ipath_devdata *, u32, u8);
787 int ipath_set_rx_pol_inv(struct ipath_devdata *dd, u8 new_pol_inv);
788 void ipath_enable_armlaunch(struct ipath_devdata *);
789 void ipath_disable_armlaunch(struct ipath_devdata *);
790 void ipath_hol_down(struct ipath_devdata *);
791 void ipath_hol_up(struct ipath_devdata *);
792 void ipath_hol_event(unsigned long);
793
794 /* for use in system calls, where we want to know device type, etc. */
795 #define port_fp(fp) ((struct ipath_filedata *)(fp)->private_data)->pd
796 #define subport_fp(fp) \
797         ((struct ipath_filedata *)(fp)->private_data)->subport
798 #define tidcursor_fp(fp) \
799         ((struct ipath_filedata *)(fp)->private_data)->tidcursor
800
801 /*
802  * values for ipath_flags
803  */
804                 /* chip can report link latency (IB 1.2) */
805 #define IPATH_HAS_LINK_LATENCY 0x1
806 /* The chip is up and initted */
807 #define IPATH_INITTED       0x2
808                 /* set if any user code has set kr_rcvhdrsize */
809 #define IPATH_RCVHDRSZ_SET  0x4
810                 /* The chip is present and valid for accesses */
811 #define IPATH_PRESENT       0x8
812                 /* HT link0 is only 8 bits wide, ignore upper byte crc
813                  * errors, etc. */
814 #define IPATH_8BIT_IN_HT0   0x10
815                 /* HT link1 is only 8 bits wide, ignore upper byte crc
816                  * errors, etc. */
817 #define IPATH_8BIT_IN_HT1   0x20
818                 /* The link is down */
819 #define IPATH_LINKDOWN      0x40
820                 /* The link level is up (0x11) */
821 #define IPATH_LINKINIT      0x80
822                 /* The link is in the armed (0x21) state */
823 #define IPATH_LINKARMED     0x100
824                 /* The link is in the active (0x31) state */
825 #define IPATH_LINKACTIVE    0x200
826                 /* link current state is unknown */
827 #define IPATH_LINKUNK       0x400
828                 /* Write combining flush needed for PIO */
829 #define IPATH_PIO_FLUSH_WC  0x1000
830                 /* no IB cable, or no device on IB cable */
831 #define IPATH_NOCABLE       0x4000
832                 /* Supports port zero per packet receive interrupts via
833                  * GPIO */
834 #define IPATH_GPIO_INTR     0x8000
835                 /* uses the coded 4byte TID, not 8 byte */
836 #define IPATH_4BYTE_TID     0x10000
837                 /* packet/word counters are 32 bit, else those 4 counters
838                  * are 64bit */
839 #define IPATH_32BITCOUNTERS 0x20000
840                 /* can miss port0 rx interrupts */
841                 /* Interrupt register is 64 bits */
842 #define IPATH_INTREG_64     0x40000
843 #define IPATH_DISABLED      0x80000 /* administratively disabled */
844                 /* Use GPIO interrupts for new counters */
845 #define IPATH_GPIO_ERRINTRS 0x100000
846 #define IPATH_SWAP_PIOBUFS  0x200000
847                 /* Suppress heartbeat, even if turning off loopback */
848 #define IPATH_NO_HRTBT      0x1000000
849 #define IPATH_HAS_MULT_IB_SPEED 0x8000000
850 #define IPATH_IB_FORCE_NOTIFY 0x80000000 /* force notify on next ib change */
851
852 /* Bits in GPIO for the added interrupts */
853 #define IPATH_GPIO_PORT0_BIT 2
854 #define IPATH_GPIO_RXUVL_BIT 3
855 #define IPATH_GPIO_OVRUN_BIT 4
856 #define IPATH_GPIO_LLI_BIT 5
857 #define IPATH_GPIO_ERRINTR_MASK 0x38
858
859 /* portdata flag bit offsets */
860                 /* waiting for a packet to arrive */
861 #define IPATH_PORT_WAITING_RCV   2
862                 /* master has not finished initializing */
863 #define IPATH_PORT_MASTER_UNINIT 4
864                 /* waiting for an urgent packet to arrive */
865 #define IPATH_PORT_WAITING_URG 5
866
867 /* free up any allocated data at closes */
868 void ipath_free_data(struct ipath_portdata *dd);
869 u32 __iomem *ipath_getpiobuf(struct ipath_devdata *, u32 *);
870 void ipath_init_iba6120_funcs(struct ipath_devdata *);
871 void ipath_init_iba6110_funcs(struct ipath_devdata *);
872 void ipath_get_eeprom_info(struct ipath_devdata *);
873 int ipath_update_eeprom_log(struct ipath_devdata *dd);
874 void ipath_inc_eeprom_err(struct ipath_devdata *dd, u32 eidx, u32 incr);
875 u64 ipath_snap_cntr(struct ipath_devdata *, ipath_creg);
876 void signal_ib_event(struct ipath_devdata *dd, enum ib_event_type ev);
877
878 /*
879  * Set LED override, only the two LSBs have "public" meaning, but
880  * any non-zero value substitutes them for the Link and LinkTrain
881  * LED states.
882  */
883 #define IPATH_LED_PHYS 1 /* Physical (linktraining) GREEN LED */
884 #define IPATH_LED_LOG 2  /* Logical (link) YELLOW LED */
885 void ipath_set_led_override(struct ipath_devdata *dd, unsigned int val);
886
887 /*
888  * number of words used for protocol header if not set by ipath_userinit();
889  */
890 #define IPATH_DFLT_RCVHDRSIZE 9
891
892 int ipath_get_user_pages(unsigned long, size_t, struct page **);
893 void ipath_release_user_pages(struct page **, size_t);
894 void ipath_release_user_pages_on_close(struct page **, size_t);
895 int ipath_eeprom_read(struct ipath_devdata *, u8, void *, int);
896 int ipath_eeprom_write(struct ipath_devdata *, u8, const void *, int);
897
898 /* these are used for the registers that vary with port */
899 void ipath_write_kreg_port(const struct ipath_devdata *, ipath_kreg,
900                            unsigned, u64);
901
902 /*
903  * We could have a single register get/put routine, that takes a group type,
904  * but this is somewhat clearer and cleaner.  It also gives us some error
905  * checking.  64 bit register reads should always work, but are inefficient
906  * on opteron (the northbridge always generates 2 separate HT 32 bit reads),
907  * so we use kreg32 wherever possible.  User register and counter register
908  * reads are always 32 bit reads, so only one form of those routines.
909  */
910
911 /*
912  * At the moment, none of the s-registers are writable, so no
913  * ipath_write_sreg(), and none of the c-registers are writable, so no
914  * ipath_write_creg().
915  */
916
917 /**
918  * ipath_read_ureg32 - read 32-bit virtualized per-port register
919  * @dd: device
920  * @regno: register number
921  * @port: port number
922  *
923  * Return the contents of a register that is virtualized to be per port.
924  * Returns -1 on errors (not distinguishable from valid contents at
925  * runtime; we may add a separate error variable at some point).
926  */
927 static inline u32 ipath_read_ureg32(const struct ipath_devdata *dd,
928                                     ipath_ureg regno, int port)
929 {
930         if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
931                 return 0;
932
933         return readl(regno + (u64 __iomem *)
934                      (dd->ipath_uregbase +
935                       (char __iomem *)dd->ipath_kregbase +
936                       dd->ipath_ureg_align * port));
937 }
938
939 /**
940  * ipath_write_ureg - write 32-bit virtualized per-port register
941  * @dd: device
942  * @regno: register number
943  * @value: value
944  * @port: port
945  *
946  * Write the contents of a register that is virtualized to be per port.
947  */
948 static inline void ipath_write_ureg(const struct ipath_devdata *dd,
949                                     ipath_ureg regno, u64 value, int port)
950 {
951         u64 __iomem *ubase = (u64 __iomem *)
952                 (dd->ipath_uregbase + (char __iomem *) dd->ipath_kregbase +
953                  dd->ipath_ureg_align * port);
954         if (dd->ipath_kregbase)
955                 writeq(value, &ubase[regno]);
956 }
957
958 static inline u32 ipath_read_kreg32(const struct ipath_devdata *dd,
959                                     ipath_kreg regno)
960 {
961         if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
962                 return -1;
963         return readl((u32 __iomem *) & dd->ipath_kregbase[regno]);
964 }
965
966 static inline u64 ipath_read_kreg64(const struct ipath_devdata *dd,
967                                     ipath_kreg regno)
968 {
969         if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
970                 return -1;
971
972         return readq(&dd->ipath_kregbase[regno]);
973 }
974
975 static inline void ipath_write_kreg(const struct ipath_devdata *dd,
976                                     ipath_kreg regno, u64 value)
977 {
978         if (dd->ipath_kregbase)
979                 writeq(value, &dd->ipath_kregbase[regno]);
980 }
981
982 static inline u64 ipath_read_creg(const struct ipath_devdata *dd,
983                                   ipath_sreg regno)
984 {
985         if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
986                 return 0;
987
988         return readq(regno + (u64 __iomem *)
989                      (dd->ipath_cregbase +
990                       (char __iomem *)dd->ipath_kregbase));
991 }
992
993 static inline u32 ipath_read_creg32(const struct ipath_devdata *dd,
994                                          ipath_sreg regno)
995 {
996         if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
997                 return 0;
998         return readl(regno + (u64 __iomem *)
999                      (dd->ipath_cregbase +
1000                       (char __iomem *)dd->ipath_kregbase));
1001 }
1002
1003 static inline void ipath_write_creg(const struct ipath_devdata *dd,
1004                                     ipath_creg regno, u64 value)
1005 {
1006         if (dd->ipath_kregbase)
1007                 writeq(value, regno + (u64 __iomem *)
1008                        (dd->ipath_cregbase +
1009                         (char __iomem *)dd->ipath_kregbase));
1010 }
1011
1012 static inline void ipath_clear_rcvhdrtail(const struct ipath_portdata *pd)
1013 {
1014         *((u64 *) pd->port_rcvhdrtail_kvaddr) = 0ULL;
1015 }
1016
1017 static inline u32 ipath_get_rcvhdrtail(const struct ipath_portdata *pd)
1018 {
1019         return (u32) le64_to_cpu(*((volatile __le64 *)
1020                                 pd->port_rcvhdrtail_kvaddr));
1021 }
1022
1023 static inline u64 ipath_read_ireg(const struct ipath_devdata *dd, ipath_kreg r)
1024 {
1025         return (dd->ipath_flags & IPATH_INTREG_64) ?
1026                 ipath_read_kreg64(dd, r) : ipath_read_kreg32(dd, r);
1027 }
1028
1029 /*
1030  * from contents of IBCStatus (or a saved copy), return linkstate
1031  * Report ACTIVE_DEFER as ACTIVE, because we treat them the same
1032  * everywhere, anyway (and should be, for almost all purposes).
1033  */
1034 static inline u32 ipath_ib_linkstate(struct ipath_devdata *dd, u64 ibcs)
1035 {
1036         u32 state = (u32)(ibcs >> dd->ibcs_ls_shift) &
1037                 INFINIPATH_IBCS_LINKSTATE_MASK;
1038         if (state == INFINIPATH_IBCS_L_STATE_ACT_DEFER)
1039                 state = INFINIPATH_IBCS_L_STATE_ACTIVE;
1040         return state;
1041 }
1042
1043 /* from contents of IBCStatus (or a saved copy), return linktrainingstate */
1044 static inline u32 ipath_ib_linktrstate(struct ipath_devdata *dd, u64 ibcs)
1045 {
1046         return (u32)(ibcs >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
1047                 dd->ibcs_lts_mask;
1048 }
1049
1050 /*
1051  * from contents of IBCStatus (or a saved copy), return logical link state
1052  * combination of link state and linktraining state (down, active, init,
1053  * arm, etc.
1054  */
1055 static inline u32 ipath_ib_state(struct ipath_devdata *dd, u64 ibcs)
1056 {
1057         u32 ibs;
1058         ibs = (u32)(ibcs >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
1059                 dd->ibcs_lts_mask;
1060         ibs |= (u32)(ibcs &
1061                 (INFINIPATH_IBCS_LINKSTATE_MASK << dd->ibcs_ls_shift));
1062         return ibs;
1063 }
1064
1065 /*
1066  * sysfs interface.
1067  */
1068
1069 struct device_driver;
1070
1071 extern const char ib_ipath_version[];
1072
1073 extern struct attribute_group *ipath_driver_attr_groups[];
1074
1075 int ipath_device_create_group(struct device *, struct ipath_devdata *);
1076 void ipath_device_remove_group(struct device *, struct ipath_devdata *);
1077 int ipath_expose_reset(struct device *);
1078
1079 int ipath_init_ipathfs(void);
1080 void ipath_exit_ipathfs(void);
1081 int ipathfs_add_device(struct ipath_devdata *);
1082 int ipathfs_remove_device(struct ipath_devdata *);
1083
1084 /*
1085  * dma_addr wrappers - all 0's invalid for hw
1086  */
1087 dma_addr_t ipath_map_page(struct pci_dev *, struct page *, unsigned long,
1088                           size_t, int);
1089 dma_addr_t ipath_map_single(struct pci_dev *, void *, size_t, int);
1090
1091 /*
1092  * Flush write combining store buffers (if present) and perform a write
1093  * barrier.
1094  */
1095 #if defined(CONFIG_X86_64)
1096 #define ipath_flush_wc() asm volatile("sfence" ::: "memory")
1097 #else
1098 #define ipath_flush_wc() wmb()
1099 #endif
1100
1101 extern unsigned ipath_debug; /* debugging bit mask */
1102 extern unsigned ipath_mtu4096;
1103
1104 #define IPATH_MAX_PARITY_ATTEMPTS 10000 /* max times to try recovery */
1105
1106 const char *ipath_get_unit_name(int unit);
1107
1108 extern struct mutex ipath_mutex;
1109
1110 #define IPATH_DRV_NAME          "ib_ipath"
1111 #define IPATH_MAJOR             233
1112 #define IPATH_USER_MINOR_BASE   0
1113 #define IPATH_DIAGPKT_MINOR     127
1114 #define IPATH_DIAG_MINOR_BASE   129
1115 #define IPATH_NMINORS           255
1116
1117 #define ipath_dev_err(dd,fmt,...) \
1118         do { \
1119                 const struct ipath_devdata *__dd = (dd); \
1120                 if (__dd->pcidev) \
1121                         dev_err(&__dd->pcidev->dev, "%s: " fmt, \
1122                                 ipath_get_unit_name(__dd->ipath_unit), \
1123                                 ##__VA_ARGS__); \
1124                 else \
1125                         printk(KERN_ERR IPATH_DRV_NAME ": %s: " fmt, \
1126                                ipath_get_unit_name(__dd->ipath_unit), \
1127                                ##__VA_ARGS__); \
1128         } while (0)
1129
1130 #if _IPATH_DEBUGGING
1131
1132 # define __IPATH_DBG_WHICH(which,fmt,...) \
1133         do { \
1134                 if(unlikely(ipath_debug&(which))) \
1135                         printk(KERN_DEBUG IPATH_DRV_NAME ": %s: " fmt, \
1136                                __func__,##__VA_ARGS__); \
1137         } while(0)
1138
1139 # define ipath_dbg(fmt,...) \
1140         __IPATH_DBG_WHICH(__IPATH_DBG,fmt,##__VA_ARGS__)
1141 # define ipath_cdbg(which,fmt,...) \
1142         __IPATH_DBG_WHICH(__IPATH_##which##DBG,fmt,##__VA_ARGS__)
1143
1144 #else /* ! _IPATH_DEBUGGING */
1145
1146 # define ipath_dbg(fmt,...)
1147 # define ipath_cdbg(which,fmt,...)
1148
1149 #endif /* _IPATH_DEBUGGING */
1150
1151 /*
1152  * this is used for formatting hw error messages...
1153  */
1154 struct ipath_hwerror_msgs {
1155         u64 mask;
1156         const char *msg;
1157 };
1158
1159 #define INFINIPATH_HWE_MSG(a, b) { .mask = INFINIPATH_HWE_##a, .msg = b }
1160
1161 /* in ipath_intr.c... */
1162 void ipath_format_hwerrors(u64 hwerrs,
1163                            const struct ipath_hwerror_msgs *hwerrmsgs,
1164                            size_t nhwerrmsgs,
1165                            char *msg, size_t lmsg);
1166
1167 #endif                          /* _IPATH_KERNEL_H */