2 * Copyright 2004-2009 Analog Devices Inc.
3 * 2005 National ICT Australia (NICTA)
4 * Aidan Williams <aidan@nicta.com.au>
6 * Licensed under the GPL-2 or later.
9 #include <linux/device.h>
10 #include <linux/platform_device.h>
11 #include <linux/mtd/mtd.h>
12 #include <linux/mtd/partitions.h>
13 #include <linux/mtd/physmap.h>
14 #include <linux/spi/spi.h>
15 #include <linux/spi/flash.h>
16 #include <linux/i2c.h>
17 #include <linux/irq.h>
18 #include <linux/interrupt.h>
19 #include <linux/usb/sl811.h>
20 #include <linux/usb/musb.h>
21 #include <linux/leds.h>
22 #include <linux/input.h>
24 #include <asm/bfin5xx_spi.h>
25 #include <asm/reboot.h>
27 #include <asm/portmux.h>
29 #include <linux/spi/ad7877.h>
32 * Name the Board for the /proc/cpuinfo
34 #ifdef CONFIG_BFIN527_EZKIT_V2
35 const char bfin_board_name[] = "ADI BF527-EZKIT V2";
37 const char bfin_board_name[] = "ADI BF527-EZKIT";
41 * Driver needs to know address, irq and flag pin.
44 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
45 #include <linux/usb/isp1760.h>
46 static struct resource bfin_isp1760_resources[] = {
49 .end = 0x203C0000 + 0x000fffff,
50 .flags = IORESOURCE_MEM,
55 .flags = IORESOURCE_IRQ,
59 static struct isp1760_platform_data isp1760_priv = {
64 .dack_polarity_high = 0,
65 .dreq_polarity_high = 0,
68 static struct platform_device bfin_isp1760_device = {
72 .platform_data = &isp1760_priv,
74 .num_resources = ARRAY_SIZE(bfin_isp1760_resources),
75 .resource = bfin_isp1760_resources,
79 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
80 static struct resource musb_resources[] = {
84 .flags = IORESOURCE_MEM,
86 [1] = { /* general IRQ */
87 .start = IRQ_USB_INT0,
89 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
94 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
98 static struct musb_hdrc_config musb_config = {
105 .gpio_vrsel = GPIO_PG13,
108 static struct musb_hdrc_platform_data musb_plat = {
109 #if defined(CONFIG_USB_MUSB_OTG)
111 #elif defined(CONFIG_USB_MUSB_HDRC_HCD)
113 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
114 .mode = MUSB_PERIPHERAL,
116 .config = &musb_config,
119 static u64 musb_dmamask = ~(u32)0;
121 static struct platform_device musb_device = {
125 .dma_mask = &musb_dmamask,
126 .coherent_dma_mask = 0xffffffff,
127 .platform_data = &musb_plat,
129 .num_resources = ARRAY_SIZE(musb_resources),
130 .resource = musb_resources,
134 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
136 static struct resource bf52x_t350mcqb_resources[] = {
138 .start = IRQ_PPI_ERROR,
139 .end = IRQ_PPI_ERROR,
140 .flags = IORESOURCE_IRQ,
144 static struct platform_device bf52x_t350mcqb_device = {
145 .name = "bfin-t350mcqb",
147 .num_resources = ARRAY_SIZE(bf52x_t350mcqb_resources),
148 .resource = bf52x_t350mcqb_resources,
152 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
153 #include <asm/bfin-lq035q1.h>
155 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
156 .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
157 .ppi_mode = USE_RGB565_8_BIT_PPI,
160 static struct resource bfin_lq035q1_resources[] = {
162 .start = IRQ_PPI_ERROR,
163 .end = IRQ_PPI_ERROR,
164 .flags = IORESOURCE_IRQ,
168 static struct platform_device bfin_lq035q1_device = {
169 .name = "bfin-lq035q1",
171 .num_resources = ARRAY_SIZE(bfin_lq035q1_resources),
172 .resource = bfin_lq035q1_resources,
174 .platform_data = &bfin_lq035q1_data,
179 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
180 static struct mtd_partition ezkit_partitions[] = {
182 .name = "bootloader(nor)",
186 .name = "linux kernel(nor)",
188 .offset = MTDPART_OFS_APPEND,
190 .name = "file system(nor)",
191 .size = MTDPART_SIZ_FULL,
192 .offset = MTDPART_OFS_APPEND,
196 static struct physmap_flash_data ezkit_flash_data = {
198 .parts = ezkit_partitions,
199 .nr_parts = ARRAY_SIZE(ezkit_partitions),
202 static struct resource ezkit_flash_resource = {
205 .flags = IORESOURCE_MEM,
208 static struct platform_device ezkit_flash_device = {
209 .name = "physmap-flash",
212 .platform_data = &ezkit_flash_data,
215 .resource = &ezkit_flash_resource,
219 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
220 static struct mtd_partition partition_info[] = {
222 .name = "linux kernel(nand)",
224 .size = 4 * 1024 * 1024,
227 .name = "file system(nand)",
228 .offset = MTDPART_OFS_APPEND,
229 .size = MTDPART_SIZ_FULL,
233 static struct bf5xx_nand_platform bf5xx_nand_platform = {
234 .page_size = NFC_PG_SIZE_256,
235 .data_width = NFC_NWIDTH_8,
236 .partitions = partition_info,
237 .nr_partitions = ARRAY_SIZE(partition_info),
242 static struct resource bf5xx_nand_resources[] = {
245 .end = NFC_DATA_RD + 2,
246 .flags = IORESOURCE_MEM,
251 .flags = IORESOURCE_IRQ,
255 static struct platform_device bf5xx_nand_device = {
256 .name = "bf5xx-nand",
258 .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
259 .resource = bf5xx_nand_resources,
261 .platform_data = &bf5xx_nand_platform,
266 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
267 static struct resource bfin_pcmcia_cf_resources[] = {
269 .start = 0x20310000, /* IO PORT */
271 .flags = IORESOURCE_MEM,
273 .start = 0x20311000, /* Attribute Memory */
275 .flags = IORESOURCE_MEM,
279 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
281 .start = 6, /* Card Detect PF6 */
283 .flags = IORESOURCE_IRQ,
287 static struct platform_device bfin_pcmcia_cf_device = {
288 .name = "bfin_cf_pcmcia",
290 .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
291 .resource = bfin_pcmcia_cf_resources,
295 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
296 static struct platform_device rtc_device = {
302 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
303 #include <linux/smc91x.h>
305 static struct smc91x_platdata smc91x_info = {
306 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
307 .leda = RPC_LED_100_10,
308 .ledb = RPC_LED_TX_RX,
311 static struct resource smc91x_resources[] = {
313 .name = "smc91x-regs",
315 .end = 0x20300300 + 16,
316 .flags = IORESOURCE_MEM,
321 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
324 static struct platform_device smc91x_device = {
327 .num_resources = ARRAY_SIZE(smc91x_resources),
328 .resource = smc91x_resources,
330 .platform_data = &smc91x_info,
335 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
336 static struct resource dm9000_resources[] = {
339 .end = 0x203FB800 + 1,
340 .flags = IORESOURCE_MEM,
343 .start = 0x203FB800 + 4,
344 .end = 0x203FB800 + 5,
345 .flags = IORESOURCE_MEM,
350 .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
354 static struct platform_device dm9000_device = {
357 .num_resources = ARRAY_SIZE(dm9000_resources),
358 .resource = dm9000_resources,
362 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
363 static struct resource sl811_hcd_resources[] = {
367 .flags = IORESOURCE_MEM,
371 .flags = IORESOURCE_MEM,
373 .start = CONFIG_USB_SL811_BFIN_IRQ,
374 .end = CONFIG_USB_SL811_BFIN_IRQ,
375 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
379 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
380 void sl811_port_power(struct device *dev, int is_on)
382 gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
383 gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
387 static struct sl811_platform_data sl811_priv = {
389 .power = 250, /* == 500mA */
390 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
391 .port_power = &sl811_port_power,
395 static struct platform_device sl811_hcd_device = {
399 .platform_data = &sl811_priv,
401 .num_resources = ARRAY_SIZE(sl811_hcd_resources),
402 .resource = sl811_hcd_resources,
406 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
407 static struct platform_device bfin_mii_bus = {
408 .name = "bfin_mii_bus",
411 static struct platform_device bfin_mac_device = {
413 .dev.platform_data = &bfin_mii_bus,
417 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
418 static struct resource net2272_bfin_resources[] = {
421 .end = 0x20300000 + 0x100,
422 .flags = IORESOURCE_MEM,
426 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
430 static struct platform_device net2272_bfin_device = {
433 .num_resources = ARRAY_SIZE(net2272_bfin_resources),
434 .resource = net2272_bfin_resources,
438 #if defined(CONFIG_MTD_M25P80) \
439 || defined(CONFIG_MTD_M25P80_MODULE)
440 static struct mtd_partition bfin_spi_flash_partitions[] = {
442 .name = "bootloader(spi)",
445 .mask_flags = MTD_CAP_ROM
447 .name = "linux kernel(spi)",
448 .size = MTDPART_SIZ_FULL,
449 .offset = MTDPART_OFS_APPEND,
453 static struct flash_platform_data bfin_spi_flash_data = {
455 .parts = bfin_spi_flash_partitions,
456 .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
460 /* SPI flash chip (m25p64) */
461 static struct bfin5xx_spi_chip spi_flash_chip_info = {
462 .enable_dma = 0, /* use dma transfer with this chip*/
467 #if defined(CONFIG_BFIN_SPI_ADC) \
468 || defined(CONFIG_BFIN_SPI_ADC_MODULE)
470 static struct bfin5xx_spi_chip spi_adc_chip_info = {
471 .enable_dma = 1, /* use dma transfer with this chip*/
476 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
477 || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
478 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
484 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
485 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
491 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
492 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
497 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
499 .vref_delay_usecs = 50, /* internal, no capacitor */
502 .pressure_max = 1000,
504 .stopacq_polarity = 1,
505 .first_conversion_delay = 3,
506 .acquisition_time = 1,
508 .pen_down_acc_interval = 1,
512 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
513 #include <linux/spi/ad7879.h>
514 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
515 .model = 7879, /* Model = AD7879 */
516 .x_plate_ohms = 620, /* 620 Ohm from the touch datasheet */
517 .pressure_max = 10000,
519 .first_conversion_delay = 3, /* wait 512us before do a first conversion */
520 .acquisition_time = 1, /* 4us acquisition time per sample */
521 .median = 2, /* do 8 measurements */
522 .averaging = 1, /* take the average of 4 middle samples */
523 .pen_down_acc_interval = 255, /* 9.4 ms */
524 .gpio_output = 1, /* configure AUX/VBAT/GPIO as GPIO output */
525 .gpio_default = 1, /* During initialization set GPIO = HIGH */
529 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
530 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
536 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
537 static struct bfin5xx_spi_chip spidev_chip_info = {
543 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
544 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
550 static struct spi_board_info bfin_spi_board_info[] __initdata = {
551 #if defined(CONFIG_MTD_M25P80) \
552 || defined(CONFIG_MTD_M25P80_MODULE)
554 /* the modalias must be the same as spi device driver name */
555 .modalias = "m25p80", /* Name of spi_driver for this device */
556 .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
557 .bus_num = 0, /* Framework bus number */
558 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
559 .platform_data = &bfin_spi_flash_data,
560 .controller_data = &spi_flash_chip_info,
565 #if defined(CONFIG_BFIN_SPI_ADC) \
566 || defined(CONFIG_BFIN_SPI_ADC_MODULE)
568 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
569 .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
570 .bus_num = 0, /* Framework bus number */
571 .chip_select = 1, /* Framework chip select. */
572 .platform_data = NULL, /* No spi_driver specific config */
573 .controller_data = &spi_adc_chip_info,
577 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
578 || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
580 .modalias = "ad1836",
581 .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
583 .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
584 .controller_data = &ad1836_spi_chip_info,
587 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
589 .modalias = "mmc_spi",
590 .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
593 .controller_data = &mmc_spi_chip_info,
598 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
600 .modalias = "ad7877",
601 .platform_data = &bfin_ad7877_ts_info,
603 .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
606 .controller_data = &spi_ad7877_chip_info,
609 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
611 .modalias = "ad7879",
612 .platform_data = &bfin_ad7879_ts_info,
614 .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
617 .controller_data = &spi_ad7879_chip_info,
618 .mode = SPI_CPHA | SPI_CPOL,
621 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
623 .modalias = "spidev",
624 .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
627 .controller_data = &spidev_chip_info,
630 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
632 .modalias = "bfin-lq035q1-spi",
633 .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
636 .controller_data = &lq035q1_spi_chip_info,
637 .mode = SPI_CPHA | SPI_CPOL,
642 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
643 /* SPI controller data */
644 static struct bfin5xx_spi_master bfin_spi0_info = {
646 .enable_dma = 1, /* master has the ability to do dma transfer */
647 .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
651 static struct resource bfin_spi0_resource[] = {
653 .start = SPI0_REGBASE,
654 .end = SPI0_REGBASE + 0xFF,
655 .flags = IORESOURCE_MEM,
660 .flags = IORESOURCE_DMA,
665 .flags = IORESOURCE_IRQ,
669 static struct platform_device bfin_spi0_device = {
671 .id = 0, /* Bus number */
672 .num_resources = ARRAY_SIZE(bfin_spi0_resource),
673 .resource = bfin_spi0_resource,
675 .platform_data = &bfin_spi0_info, /* Passed to driver */
678 #endif /* spi master and devices */
680 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
681 #ifdef CONFIG_SERIAL_BFIN_UART0
682 static struct resource bfin_uart0_resources[] = {
686 .flags = IORESOURCE_MEM,
689 .start = IRQ_UART0_RX,
690 .end = IRQ_UART0_RX+1,
691 .flags = IORESOURCE_IRQ,
694 .start = IRQ_UART0_ERROR,
695 .end = IRQ_UART0_ERROR,
696 .flags = IORESOURCE_IRQ,
699 .start = CH_UART0_TX,
701 .flags = IORESOURCE_DMA,
704 .start = CH_UART0_RX,
706 .flags = IORESOURCE_DMA,
710 unsigned short bfin_uart0_peripherals[] = {
711 P_UART0_TX, P_UART0_RX, 0
714 static struct platform_device bfin_uart0_device = {
717 .num_resources = ARRAY_SIZE(bfin_uart0_resources),
718 .resource = bfin_uart0_resources,
720 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
724 #ifdef CONFIG_SERIAL_BFIN_UART1
725 static struct resource bfin_uart1_resources[] = {
729 .flags = IORESOURCE_MEM,
732 .start = IRQ_UART1_RX,
733 .end = IRQ_UART1_RX+1,
734 .flags = IORESOURCE_IRQ,
737 .start = IRQ_UART1_ERROR,
738 .end = IRQ_UART1_ERROR,
739 .flags = IORESOURCE_IRQ,
742 .start = CH_UART1_TX,
744 .flags = IORESOURCE_DMA,
747 .start = CH_UART1_RX,
749 .flags = IORESOURCE_DMA,
751 #ifdef CONFIG_BFIN_UART1_CTSRTS
755 .flags = IORESOURCE_IO,
760 .flags = IORESOURCE_IO,
765 unsigned short bfin_uart1_peripherals[] = {
766 P_UART1_TX, P_UART1_RX, 0
769 static struct platform_device bfin_uart1_device = {
772 .num_resources = ARRAY_SIZE(bfin_uart1_resources),
773 .resource = bfin_uart1_resources,
775 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
781 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
782 #ifdef CONFIG_BFIN_SIR0
783 static struct resource bfin_sir0_resources[] = {
787 .flags = IORESOURCE_MEM,
790 .start = IRQ_UART0_RX,
791 .end = IRQ_UART0_RX+1,
792 .flags = IORESOURCE_IRQ,
795 .start = CH_UART0_RX,
796 .end = CH_UART0_RX+1,
797 .flags = IORESOURCE_DMA,
801 static struct platform_device bfin_sir0_device = {
804 .num_resources = ARRAY_SIZE(bfin_sir0_resources),
805 .resource = bfin_sir0_resources,
808 #ifdef CONFIG_BFIN_SIR1
809 static struct resource bfin_sir1_resources[] = {
813 .flags = IORESOURCE_MEM,
816 .start = IRQ_UART1_RX,
817 .end = IRQ_UART1_RX+1,
818 .flags = IORESOURCE_IRQ,
821 .start = CH_UART1_RX,
822 .end = CH_UART1_RX+1,
823 .flags = IORESOURCE_DMA,
827 static struct platform_device bfin_sir1_device = {
830 .num_resources = ARRAY_SIZE(bfin_sir1_resources),
831 .resource = bfin_sir1_resources,
836 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
837 static struct resource bfin_twi0_resource[] = {
839 .start = TWI0_REGBASE,
841 .flags = IORESOURCE_MEM,
846 .flags = IORESOURCE_IRQ,
850 static struct platform_device i2c_bfin_twi_device = {
851 .name = "i2c-bfin-twi",
853 .num_resources = ARRAY_SIZE(bfin_twi0_resource),
854 .resource = bfin_twi0_resource,
858 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
859 #include <linux/mfd/adp5520.h>
862 * ADP5520/5501 LEDs Data
865 static struct led_info adp5520_leds[] = {
867 .name = "adp5520-led1",
868 .default_trigger = "none",
869 .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
873 static struct adp5520_leds_platform_data adp5520_leds_data = {
874 .num_leds = ARRAY_SIZE(adp5520_leds),
875 .leds = adp5520_leds,
876 .fade_in = ADP5520_FADE_T_600ms,
877 .fade_out = ADP5520_FADE_T_600ms,
878 .led_on_time = ADP5520_LED_ONT_600ms,
882 * ADP5520 Keypad Data
885 static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
886 [ADP5520_KEY(3, 3)] = KEY_1,
887 [ADP5520_KEY(2, 3)] = KEY_2,
888 [ADP5520_KEY(1, 3)] = KEY_3,
889 [ADP5520_KEY(0, 3)] = KEY_UP,
890 [ADP5520_KEY(3, 2)] = KEY_4,
891 [ADP5520_KEY(2, 2)] = KEY_5,
892 [ADP5520_KEY(1, 2)] = KEY_6,
893 [ADP5520_KEY(0, 2)] = KEY_DOWN,
894 [ADP5520_KEY(3, 1)] = KEY_7,
895 [ADP5520_KEY(2, 1)] = KEY_8,
896 [ADP5520_KEY(1, 1)] = KEY_9,
897 [ADP5520_KEY(0, 1)] = KEY_DOT,
898 [ADP5520_KEY(3, 0)] = KEY_BACKSPACE,
899 [ADP5520_KEY(2, 0)] = KEY_0,
900 [ADP5520_KEY(1, 0)] = KEY_HELP,
901 [ADP5520_KEY(0, 0)] = KEY_ENTER,
904 static struct adp5520_keys_platform_data adp5520_keys_data = {
905 .rows_en_mask = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
906 .cols_en_mask = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
907 .keymap = adp5520_keymap,
908 .keymapsize = ARRAY_SIZE(adp5520_keymap),
913 * ADP5520/5501 Multifuction Device Init Data
916 static struct adp5520_platform_data adp5520_pdev_data = {
917 .leds = &adp5520_leds_data,
918 .keys = &adp5520_keys_data,
923 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
924 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
926 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
929 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
931 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
935 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
937 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
940 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
942 I2C_BOARD_INFO("ad7879", 0x2C),
944 .platform_data = (void *)&bfin_ad7879_ts_info,
947 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
949 I2C_BOARD_INFO("pmic-adp5520", 0x32),
951 .platform_data = (void *)&adp5520_pdev_data,
956 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
957 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
958 static struct resource bfin_sport0_uart_resources[] = {
960 .start = SPORT0_TCR1,
961 .end = SPORT0_MRCS3+4,
962 .flags = IORESOURCE_MEM,
965 .start = IRQ_SPORT0_RX,
966 .end = IRQ_SPORT0_RX+1,
967 .flags = IORESOURCE_IRQ,
970 .start = IRQ_SPORT0_ERROR,
971 .end = IRQ_SPORT0_ERROR,
972 .flags = IORESOURCE_IRQ,
976 unsigned short bfin_sport0_peripherals[] = {
977 P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
978 P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
981 static struct platform_device bfin_sport0_uart_device = {
982 .name = "bfin-sport-uart",
984 .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
985 .resource = bfin_sport0_uart_resources,
987 .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
991 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
992 static struct resource bfin_sport1_uart_resources[] = {
994 .start = SPORT1_TCR1,
995 .end = SPORT1_MRCS3+4,
996 .flags = IORESOURCE_MEM,
999 .start = IRQ_SPORT1_RX,
1000 .end = IRQ_SPORT1_RX+1,
1001 .flags = IORESOURCE_IRQ,
1004 .start = IRQ_SPORT1_ERROR,
1005 .end = IRQ_SPORT1_ERROR,
1006 .flags = IORESOURCE_IRQ,
1010 unsigned short bfin_sport1_peripherals[] = {
1011 P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
1012 P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
1015 static struct platform_device bfin_sport1_uart_device = {
1016 .name = "bfin-sport-uart",
1018 .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
1019 .resource = bfin_sport1_uart_resources,
1021 .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
1027 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1028 #include <linux/gpio_keys.h>
1030 static struct gpio_keys_button bfin_gpio_keys_table[] = {
1031 {BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
1032 {BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
1035 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
1036 .buttons = bfin_gpio_keys_table,
1037 .nbuttons = ARRAY_SIZE(bfin_gpio_keys_table),
1040 static struct platform_device bfin_device_gpiokeys = {
1041 .name = "gpio-keys",
1043 .platform_data = &bfin_gpio_keys_data,
1048 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1049 #include <asm/bfin_rotary.h>
1051 static struct bfin_rotary_platform_data bfin_rotary_data = {
1052 /*.rotary_up_key = KEY_UP,*/
1053 /*.rotary_down_key = KEY_DOWN,*/
1054 .rotary_rel_code = REL_WHEEL,
1055 .rotary_button_key = KEY_ENTER,
1056 .debounce = 10, /* 0..17 */
1057 .mode = ROT_QUAD_ENC | ROT_DEBE,
1060 static struct resource bfin_rotary_resources[] = {
1064 .flags = IORESOURCE_IRQ,
1068 static struct platform_device bfin_rotary_device = {
1069 .name = "bfin-rotary",
1071 .num_resources = ARRAY_SIZE(bfin_rotary_resources),
1072 .resource = bfin_rotary_resources,
1074 .platform_data = &bfin_rotary_data,
1079 static const unsigned int cclk_vlev_datasheet[] =
1081 VRPAIR(VLEV_100, 400000000),
1082 VRPAIR(VLEV_105, 426000000),
1083 VRPAIR(VLEV_110, 500000000),
1084 VRPAIR(VLEV_115, 533000000),
1085 VRPAIR(VLEV_120, 600000000),
1088 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
1089 .tuple_tab = cclk_vlev_datasheet,
1090 .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
1091 .vr_settling_time = 25 /* us */,
1094 static struct platform_device bfin_dpmc = {
1095 .name = "bfin dpmc",
1097 .platform_data = &bfin_dmpc_vreg_data,
1101 static struct platform_device *stamp_devices[] __initdata = {
1105 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
1109 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
1110 &bfin_pcmcia_cf_device,
1113 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
1117 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
1121 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
1122 &bfin_isp1760_device,
1125 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
1129 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
1133 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
1137 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
1142 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
1143 &net2272_bfin_device,
1146 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1150 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
1151 &bf52x_t350mcqb_device,
1154 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1155 &bfin_lq035q1_device,
1158 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1159 #ifdef CONFIG_SERIAL_BFIN_UART0
1162 #ifdef CONFIG_SERIAL_BFIN_UART1
1167 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1168 #ifdef CONFIG_BFIN_SIR0
1171 #ifdef CONFIG_BFIN_SIR1
1176 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1177 &i2c_bfin_twi_device,
1180 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1181 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1182 &bfin_sport0_uart_device,
1184 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1185 &bfin_sport1_uart_device,
1189 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1190 &bfin_device_gpiokeys,
1193 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1194 &bfin_rotary_device,
1197 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
1198 &ezkit_flash_device,
1202 static int __init ezkit_init(void)
1204 printk(KERN_INFO "%s(): registering device resources\n", __func__);
1205 i2c_register_board_info(0, bfin_i2c_board_info,
1206 ARRAY_SIZE(bfin_i2c_board_info));
1207 platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
1208 spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
1212 arch_initcall(ezkit_init);
1214 static struct platform_device *ezkit_early_devices[] __initdata = {
1215 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
1216 #ifdef CONFIG_SERIAL_BFIN_UART0
1219 #ifdef CONFIG_SERIAL_BFIN_UART1
1224 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
1225 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1226 &bfin_sport0_uart_device,
1228 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1229 &bfin_sport1_uart_device,
1234 void __init native_machine_early_platform_add_devices(void)
1236 printk(KERN_INFO "register early platform devices\n");
1237 early_platform_add_devices(ezkit_early_devices,
1238 ARRAY_SIZE(ezkit_early_devices));
1241 void native_machine_restart(char *cmd)
1243 /* workaround reboot hang when booting from SPI */
1244 if ((bfin_read_SYSCR() & 0x7) == 0x3)
1245 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
1248 void bfin_get_ether_addr(char *addr)
1250 /* the MAC is stored in OTP memory page 0xDF */
1253 u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
1255 ret = otp_read(0xDF, 0x00, &otp_mac);
1257 char *otp_mac_p = (char *)&otp_mac;
1258 for (ret = 0; ret < 6; ++ret)
1259 addr[ret] = otp_mac_p[5 - ret];
1262 EXPORT_SYMBOL(bfin_get_ether_addr);