SAFE public projects git trees. - safe/jmp/linux-2.6/blob - arch/arm/mach-pxa/spitz.c

   1 /*
   2  * Support for Sharp SL-Cxx00 Series of PDAs
   3  * Models: SL-C3000 (Spitz), SL-C1000 (Akita) and SL-C3100 (Borzoi)
   4  *
   5  * Copyright (c) 2005 Richard Purdie
   6  *
   7  * Based on Sharp's 2.4 kernel patches/lubbock.c
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License version 2 as
  11  * published by the Free Software Foundation.
  12  *
  13  */
  14
  15 #include <linux/kernel.h>
  16 #include <linux/init.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/delay.h>
  19 #include <linux/major.h>
  20 #include <linux/fs.h>
  21 #include <linux/interrupt.h>
  22 #include <linux/mmc/host.h>
  23
  24 #include <asm/setup.h>
  25 #include <asm/memory.h>
  26 #include <asm/mach-types.h>
  27 #include <asm/hardware.h>
  28 #include <asm/irq.h>
  29 #include <asm/io.h>
  30
  31 #include <asm/mach/arch.h>
  32 #include <asm/mach/map.h>
  33 #include <asm/mach/irq.h>
  34
  35 #include <asm/arch/pxa-regs.h>
  36 #include <asm/arch/irq.h>
  37 #include <asm/arch/irda.h>
  38 #include <asm/arch/mmc.h>
  39 #include <asm/arch/ohci.h>
  40 #include <asm/arch/udc.h>
  41 #include <asm/arch/pxafb.h>
  42 #include <asm/arch/akita.h>
  43 #include <asm/arch/spitz.h>
  44 #include <asm/arch/sharpsl.h>
  45
  46 #include <asm/mach/sharpsl_param.h>
  47 #include <asm/hardware/scoop.h>
  48
  49 #include "generic.h"
  50 #include "sharpsl.h"
  51
  52 /*
  53  * Spitz SCOOP Device #1
  54  */
  55 static struct resource spitz_scoop_resources[] = {
  56         [0] = {
  57                 .start          = 0x10800000,
  58                 .end            = 0x10800fff,
  59                 .flags          = IORESOURCE_MEM,
  60         },
  61 };
  62
  63 static struct scoop_config spitz_scoop_setup = {
  64         .io_dir         = SPITZ_SCP_IO_DIR,
  65         .io_out         = SPITZ_SCP_IO_OUT,
  66         .suspend_clr = SPITZ_SCP_SUS_CLR,
  67         .suspend_set = SPITZ_SCP_SUS_SET,
  68 };
  69
  70 struct platform_device spitzscoop_device = {
  71         .name           = "sharp-scoop",
  72         .id             = 0,
  73         .dev            = {
  74                 .platform_data  = &spitz_scoop_setup,
  75         },
  76         .num_resources  = ARRAY_SIZE(spitz_scoop_resources),
  77         .resource       = spitz_scoop_resources,
  78 };
  79
  80 /*
  81  * Spitz SCOOP Device #2
  82  */
  83 static struct resource spitz_scoop2_resources[] = {
  84         [0] = {
  85                 .start          = 0x08800040,
  86                 .end            = 0x08800fff,
  87                 .flags          = IORESOURCE_MEM,
  88         },
  89 };
  90
  91 static struct scoop_config spitz_scoop2_setup = {
  92         .io_dir         = SPITZ_SCP2_IO_DIR,
  93         .io_out         = SPITZ_SCP2_IO_OUT,
  94         .suspend_clr = SPITZ_SCP2_SUS_CLR,
  95         .suspend_set = SPITZ_SCP2_SUS_SET,
  96 };
  97
  98 struct platform_device spitzscoop2_device = {
  99         .name           = "sharp-scoop",
 100         .id             = 1,
 101         .dev            = {
 102                 .platform_data  = &spitz_scoop2_setup,
 103         },
 104         .num_resources  = ARRAY_SIZE(spitz_scoop2_resources),
 105         .resource       = spitz_scoop2_resources,
 106 };
 107
 108 #define SPITZ_PWR_SD 0x01
 109 #define SPITZ_PWR_CF 0x02
 110
 111 /* Power control is shared with between one of the CF slots and SD */
 112 static void spitz_card_pwr_ctrl(int device, unsigned short new_cpr)
 113 {
 114         unsigned short cpr = read_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR);
 115
 116         if (new_cpr & 0x0007) {
 117                 set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CF_POWER);
 118                 if (!(cpr & 0x0002) && !(cpr & 0x0004))
 119                         mdelay(5);
 120                 if (device == SPITZ_PWR_CF)
 121                         cpr |= 0x0002;
 122                 if (device == SPITZ_PWR_SD)
 123                         cpr |= 0x0004;
 124                 write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, cpr | new_cpr);
 125         } else {
 126                 if (device == SPITZ_PWR_CF)
 127                         cpr &= ~0x0002;
 128                 if (device == SPITZ_PWR_SD)
 129                         cpr &= ~0x0004;
 130                 if (!(cpr & 0x0002) && !(cpr & 0x0004)) {
 131                         write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, 0x0000);
 132                         mdelay(1);
 133                         reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CF_POWER);
 134                 } else {
 135                         write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, cpr | new_cpr);
 136                 }
 137         }
 138 }
 139
 140 static void spitz_pcmcia_init(void)
 141 {
 142         /* Setup default state of GPIO outputs
 143            before we enable them as outputs. */
 144         GPSR(GPIO48_nPOE) = GPIO_bit(GPIO48_nPOE) |
 145                 GPIO_bit(GPIO49_nPWE) | GPIO_bit(GPIO50_nPIOR) |
 146                 GPIO_bit(GPIO51_nPIOW) | GPIO_bit(GPIO54_nPCE_2);
 147         GPSR(GPIO85_nPCE_1) = GPIO_bit(GPIO85_nPCE_1);
 148
 149         pxa_gpio_mode(GPIO48_nPOE_MD);
 150         pxa_gpio_mode(GPIO49_nPWE_MD);
 151         pxa_gpio_mode(GPIO50_nPIOR_MD);
 152         pxa_gpio_mode(GPIO51_nPIOW_MD);
 153         pxa_gpio_mode(GPIO55_nPREG_MD);
 154         pxa_gpio_mode(GPIO56_nPWAIT_MD);
 155         pxa_gpio_mode(GPIO57_nIOIS16_MD);
 156         pxa_gpio_mode(GPIO85_nPCE_1_MD);
 157         pxa_gpio_mode(GPIO54_nPCE_2_MD);
 158         pxa_gpio_mode(GPIO104_pSKTSEL_MD);
 159 }
 160
 161 static void spitz_pcmcia_pwr(struct device *scoop, unsigned short cpr, int nr)
 162 {
 163         /* Only need to override behaviour for slot 0 */
 164         if (nr == 0)
 165                 spitz_card_pwr_ctrl(SPITZ_PWR_CF, cpr);
 166         else
 167                 write_scoop_reg(scoop, SCOOP_CPR, cpr);
 168 }
 169
 170 static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = {
 171 {
 172         .dev        = &spitzscoop_device.dev,
 173         .irq        = SPITZ_IRQ_GPIO_CF_IRQ,
 174         .cd_irq     = SPITZ_IRQ_GPIO_CF_CD,
 175         .cd_irq_str = "PCMCIA0 CD",
 176 },{
 177         .dev        = &spitzscoop2_device.dev,
 178         .irq        = SPITZ_IRQ_GPIO_CF2_IRQ,
 179         .cd_irq     = -1,
 180 },
 181 };
 182
 183 static struct scoop_pcmcia_config spitz_pcmcia_config = {
 184         .devs         = &spitz_pcmcia_scoop[0],
 185         .num_devs     = 2,
 186         .pcmcia_init  = spitz_pcmcia_init,
 187         .power_ctrl   = spitz_pcmcia_pwr,
 188 };
 189
 190 EXPORT_SYMBOL(spitzscoop_device);
 191 EXPORT_SYMBOL(spitzscoop2_device);
 192
 193
 194 /*
 195  * Spitz SSP Device
 196  *
 197  * Set the parent as the scoop device because a lot of SSP devices
 198  * also use scoop functions and this makes the power up/down order
 199  * work correctly.
 200  */
 201 struct platform_device spitzssp_device = {
 202         .name           = "corgi-ssp",
 203         .dev            = {
 204                 .parent = &spitzscoop_device.dev,
 205         },
 206         .id             = -1,
 207 };
 208
 209 struct corgissp_machinfo spitz_ssp_machinfo = {
 210         .port           = 2,
 211         .cs_lcdcon      = SPITZ_GPIO_LCDCON_CS,
 212         .cs_ads7846     = SPITZ_GPIO_ADS7846_CS,
 213         .cs_max1111     = SPITZ_GPIO_MAX1111_CS,
 214         .clk_lcdcon     = 520,
 215         .clk_ads7846    = 14,
 216         .clk_max1111    = 56,
 217 };
 218
 219
 220 /*
 221  * Spitz Backlight Device
 222  */
 223 static struct corgibl_machinfo spitz_bl_machinfo = {
 224         .max_intensity = 0x2f,
 225 };
 226
 227 static struct platform_device spitzbl_device = {
 228         .name           = "corgi-bl",
 229         .dev            = {
 230                 .platform_data  = &spitz_bl_machinfo,
 231         },
 232         .id             = -1,
 233 };
 234
 235
 236 /*
 237  * Spitz Keyboard Device
 238  */
 239 static struct platform_device spitzkbd_device = {
 240         .name           = "spitz-keyboard",
 241         .id             = -1,
 242 };
 243
 244
 245 /*
 246  * Spitz Touch Screen Device
 247  */
 248 static struct resource spitzts_resources[] = {
 249         [0] = {
 250                 .start          = SPITZ_IRQ_GPIO_TP_INT,
 251                 .end            = SPITZ_IRQ_GPIO_TP_INT,
 252                 .flags          = IORESOURCE_IRQ,
 253         },
 254 };
 255
 256 static struct corgits_machinfo  spitz_ts_machinfo = {
 257         .get_hsync_len   = spitz_get_hsync_len,
 258         .put_hsync       = spitz_put_hsync,
 259         .wait_hsync      = spitz_wait_hsync,
 260 };
 261
 262 static struct platform_device spitzts_device = {
 263         .name           = "corgi-ts",
 264         .dev            = {
 265                 .parent = &spitzssp_device.dev,
 266                 .platform_data  = &spitz_ts_machinfo,
 267         },
 268         .id             = -1,
 269         .num_resources  = ARRAY_SIZE(spitzts_resources),
 270         .resource       = spitzts_resources,
 271 };
 272
 273
 274 /*
 275  * MMC/SD Device
 276  *
 277  * The card detect interrupt isn't debounced so we delay it by 250ms
 278  * to give the card a chance to fully insert/eject.
 279  */
 280
 281 static struct pxamci_platform_data spitz_mci_platform_data;
 282
 283 static int spitz_mci_init(struct device *dev, irqreturn_t (*spitz_detect_int)(int, void *, struct pt_regs *), void *data)
 284 {
 285         int err;
 286
 287         /* setup GPIO for PXA27x MMC controller */
 288         pxa_gpio_mode(GPIO32_MMCCLK_MD);
 289         pxa_gpio_mode(GPIO112_MMCCMD_MD);
 290         pxa_gpio_mode(GPIO92_MMCDAT0_MD);
 291         pxa_gpio_mode(GPIO109_MMCDAT1_MD);
 292         pxa_gpio_mode(GPIO110_MMCDAT2_MD);
 293         pxa_gpio_mode(GPIO111_MMCDAT3_MD);
 294         pxa_gpio_mode(SPITZ_GPIO_nSD_DETECT | GPIO_IN);
 295         pxa_gpio_mode(SPITZ_GPIO_nSD_WP | GPIO_IN);
 296
 297         spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250);
 298
 299         err = request_irq(SPITZ_IRQ_GPIO_nSD_DETECT, spitz_detect_int, SA_INTERRUPT,
 300                              "MMC card detect", data);
 301         if (err) {
 302                 printk(KERN_ERR "spitz_mci_init: MMC/SD: can't request MMC card detect IRQ\n");
 303                 return -1;
 304         }
 305
 306         set_irq_type(SPITZ_IRQ_GPIO_nSD_DETECT, IRQT_BOTHEDGE);
 307
 308         return 0;
 309 }
 310
 311 static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
 312 {
 313         struct pxamci_platform_data* p_d = dev->platform_data;
 314
 315         if (( 1 << vdd) & p_d->ocr_mask)
 316                 spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0004);
 317         else
 318                 spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0000);
 319 }
 320
 321 static int spitz_mci_get_ro(struct device *dev)
 322 {
 323         return GPLR(SPITZ_GPIO_nSD_WP) & GPIO_bit(SPITZ_GPIO_nSD_WP);
 324 }
 325
 326 static void spitz_mci_exit(struct device *dev, void *data)
 327 {
 328         free_irq(SPITZ_IRQ_GPIO_nSD_DETECT, data);
 329 }
 330
 331 static struct pxamci_platform_data spitz_mci_platform_data = {
 332         .ocr_mask       = MMC_VDD_32_33|MMC_VDD_33_34,
 333         .init           = spitz_mci_init,
 334         .get_ro         = spitz_mci_get_ro,
 335         .setpower       = spitz_mci_setpower,
 336         .exit           = spitz_mci_exit,
 337 };
 338
 339
 340 /*
 341  * USB Host (OHCI)
 342  */
 343 static int spitz_ohci_init(struct device *dev)
 344 {
 345         /* Only Port 2 is connected */
 346         pxa_gpio_mode(SPITZ_GPIO_USB_CONNECT | GPIO_IN);
 347         pxa_gpio_mode(SPITZ_GPIO_USB_HOST | GPIO_OUT);
 348         pxa_gpio_mode(SPITZ_GPIO_USB_DEVICE | GPIO_IN);
 349
 350         /* Setup USB Port 2 Output Control Register */
 351         UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
 352
 353         GPSR(SPITZ_GPIO_USB_HOST) = GPIO_bit(SPITZ_GPIO_USB_HOST);
 354
 355         UHCHR = (UHCHR) &
 356                 ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE);
 357
 358         UHCRHDA |= UHCRHDA_NOCP;
 359
 360         return 0;
 361 }
 362
 363 static struct pxaohci_platform_data spitz_ohci_platform_data = {
 364         .port_mode      = PMM_NPS_MODE,
 365         .init           = spitz_ohci_init,
 366 };
 367
 368
 369 /*
 370  * Irda
 371  */
 372 static void spitz_irda_transceiver_mode(struct device *dev, int mode)
 373 {
 374         if (mode & IR_OFF)
 375                 set_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_IR_ON);
 376         else
 377                 reset_scoop_gpio(&spitzscoop2_device.dev, SPITZ_SCP2_IR_ON);
 378 }
 379
 380 #ifdef CONFIG_MACH_AKITA
 381 static void akita_irda_transceiver_mode(struct device *dev, int mode)
 382 {
 383         if (mode & IR_OFF)
 384                 akita_set_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_IR_ON);
 385         else
 386                 akita_reset_ioexp(&akitaioexp_device.dev, AKITA_IOEXP_IR_ON);
 387 }
 388 #endif
 389
 390 static struct pxaficp_platform_data spitz_ficp_platform_data = {
 391         .transceiver_cap  = IR_SIRMODE | IR_OFF,
 392         .transceiver_mode = spitz_irda_transceiver_mode,
 393 };
 394
 395
 396 /*
 397  * Spitz PXA Framebuffer
 398  */
 399 static struct pxafb_mach_info spitz_pxafb_info __initdata = {
 400         .pixclock       = 19231,
 401         .xres           = 480,
 402         .yres           = 640,
 403         .bpp            = 16,
 404         .hsync_len      = 40,
 405         .left_margin    = 46,
 406         .right_margin   = 125,
 407         .vsync_len      = 3,
 408         .upper_margin   = 1,
 409         .lower_margin   = 0,
 410         .sync           = 0,
 411         .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act | LCCR0_LDDALT | LCCR0_OUC | LCCR0_CMDIM | LCCR0_RDSTM,
 412         .lccr3          = LCCR3_PixRsEdg | LCCR3_OutEnH,
 413         .pxafb_lcd_power = spitz_lcd_power,
 414 };
 415
 416
 417 static struct platform_device *devices[] __initdata = {
 418         &spitzscoop_device,
 419         &spitzssp_device,
 420         &spitzkbd_device,
 421         &spitzts_device,
 422         &spitzbl_device,
 423 };
 424
 425 static void __init common_init(void)
 426 {
 427         PMCR = 0x00;
 428
 429         /* setup sleep mode values */
 430         PWER  = 0x00000002;
 431         PFER  = 0x00000000;
 432         PRER  = 0x00000002;
 433         PGSR0 = 0x0158C000;
 434         PGSR1 = 0x00FF0080;
 435         PGSR2 = 0x0001C004;
 436
 437         /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
 438         PCFR |= PCFR_OPDE;
 439
 440         corgi_ssp_set_machinfo(&spitz_ssp_machinfo);
 441
 442         pxa_gpio_mode(SPITZ_GPIO_HSYNC | GPIO_IN);
 443
 444         platform_add_devices(devices, ARRAY_SIZE(devices));
 445         pxa_set_mci_info(&spitz_mci_platform_data);
 446         pxa_set_ohci_info(&spitz_ohci_platform_data);
 447         pxa_set_ficp_info(&spitz_ficp_platform_data);
 448         set_pxa_fb_parent(&spitzssp_device.dev);
 449         set_pxa_fb_info(&spitz_pxafb_info);
 450 }
 451
 452 static void __init spitz_init(void)
 453 {
 454         platform_scoop_config = &spitz_pcmcia_config;
 455
 456         spitz_bl_machinfo.set_bl_intensity = spitz_bl_set_intensity;
 457
 458         common_init();
 459
 460         platform_device_register(&spitzscoop2_device);
 461 }
 462
 463 #ifdef CONFIG_MACH_AKITA
 464 /*
 465  * Akita IO Expander
 466  */
 467 struct platform_device akitaioexp_device = {
 468         .name           = "akita-ioexp",
 469         .id             = -1,
 470 };
 471
 472 static void __init akita_init(void)
 473 {
 474         spitz_ficp_platform_data.transceiver_mode = akita_irda_transceiver_mode;
 475
 476         /* We just pretend the second element of the array doesn't exist */
 477         spitz_pcmcia_config.num_devs = 1;
 478         platform_scoop_config = &spitz_pcmcia_config;
 479         spitz_bl_machinfo.set_bl_intensity = akita_bl_set_intensity;
 480
 481         platform_device_register(&akitaioexp_device);
 482
 483         spitzscoop_device.dev.parent = &akitaioexp_device.dev;
 484         common_init();
 485 }
 486 #endif
 487
 488
 489 static void __init fixup_spitz(struct machine_desc *desc,
 490                 struct tag *tags, char **cmdline, struct meminfo *mi)
 491 {
 492         sharpsl_save_param();
 493         mi->nr_banks = 1;
 494         mi->bank[0].start = 0xa0000000;
 495         mi->bank[0].node = 0;
 496         mi->bank[0].size = (64*1024*1024);
 497 }
 498
 499 #ifdef CONFIG_MACH_SPITZ
 500 MACHINE_START(SPITZ, "SHARP Spitz")
 501         .phys_ram       = 0xa0000000,
 502         .phys_io        = 0x40000000,
 503         .io_pg_offst    = (io_p2v(0x40000000) >> 18) & 0xfffc,
 504         .fixup          = fixup_spitz,
 505         .map_io         = pxa_map_io,
 506         .init_irq       = pxa_init_irq,
 507         .init_machine   = spitz_init,
 508         .timer          = &pxa_timer,
 509 MACHINE_END
 510 #endif
 511
 512 #ifdef CONFIG_MACH_BORZOI
 513 MACHINE_START(BORZOI, "SHARP Borzoi")
 514         .phys_ram       = 0xa0000000,
 515         .phys_io        = 0x40000000,
 516         .io_pg_offst    = (io_p2v(0x40000000) >> 18) & 0xfffc,
 517         .fixup          = fixup_spitz,
 518         .map_io         = pxa_map_io,
 519         .init_irq       = pxa_init_irq,
 520         .init_machine   = spitz_init,
 521         .timer          = &pxa_timer,
 522 MACHINE_END
 523 #endif
 524
 525 #ifdef CONFIG_MACH_AKITA
 526 MACHINE_START(AKITA, "SHARP Akita")
 527         .phys_ram       = 0xa0000000,
 528         .phys_io        = 0x40000000,
 529         .io_pg_offst    = (io_p2v(0x40000000) >> 18) & 0xfffc,
 530         .fixup          = fixup_spitz,
 531         .map_io         = pxa_map_io,
 532         .init_irq       = pxa_init_irq,
 533         .init_machine   = akita_init,
 534         .timer          = &pxa_timer,
 535 MACHINE_END
 536 #endif