2 Advanced Linux Sound Architecture - Driver
3 ==========================================
10 To enable ALSA support you need at least to build the kernel with
11 primary sound card support (CONFIG_SOUND). Since ALSA can emulate OSS,
12 you don't have to choose any of the OSS modules.
14 Enable "OSS API emulation" (CONFIG_SND_OSSEMUL) and both OSS mixer and
15 PCM supports if you want to run OSS applications with ALSA.
17 If you want to support the WaveTable functionality on cards such as
18 SB Live! then you need to enable "Sequencer support"
19 (CONFIG_SND_SEQUENCER).
21 To make ALSA debug messages more verbose, enable the "Verbose printk"
22 and "Debug" options. To check for memory leaks, turn on "Debug memory"
23 too. "Debug detection" will add checks for the detection of cards.
25 Please note that all the ALSA ISA drivers support the Linux isapnp API
26 (if the card supports ISA PnP). You don't need to configure the cards
33 This depends on your distribution, but normally you use the /dev/MAKEDEV
34 script to create the necessary device nodes. On some systems you use a
35 script named 'snddevices'.
41 The user can load modules with options. If the module supports more than
42 one card and you have more than one card of the same type then you can
43 specify multiple values for the option separated by commas.
45 Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
50 The core ALSA module. It is used by all ALSA card drivers.
51 It takes the following options which have global effects.
53 major - major number for sound driver
56 - limiting card index for auto-loading (1-8)
58 - For auto-loading more than one card, specify this
59 option together with snd-card-X aliases.
65 The PCM OSS emulation module.
66 This module takes options which change the mapping of devices.
68 dsp_map - PCM device number maps assigned to the 1st OSS device.
70 adsp_map - PCM device number maps assigned to the 2st OSS device.
73 - Don't block opening busy PCM devices. Default: 1
75 For example, when dsp_map=2, /dev/dsp will be mapped to PCM #2 of
76 the card #0. Similarly, when adsp_map=0, /dev/adsp will be mapped
77 to PCM #0 of the card #0.
78 For changing the second or later card, specify the option with
79 commas, such like "dsp_map=0,1".
81 nonblock_open option is used to change the behavior of the PCM
82 regarding opening the device. When this option is non-zero,
83 opening a busy OSS PCM device won't be blocked but return
84 immediately with EAGAIN (just like O_NONBLOCK flag).
89 This module takes options which change the mapping of devices.
90 similar to those of the snd-pcm-oss module.
92 midi_map - MIDI device number maps assigned to the 1st OSS device.
94 amidi_map - MIDI device number maps assigned to the 2st OSS device.
97 Common parameters for top sound card modules
98 --------------------------------------------
100 Each of top level sound card module takes the following options.
102 index - index (slot #) of sound card
103 - Values: 0 through 31 or negative
104 - If nonnegative, assign that index number
105 - if negative, interpret as a bitmask of permissible
106 indices; the first free permitted index is assigned
108 id - card ID (identifier or name)
109 - Can be up to 15 characters long
110 - Default: the card type
111 - A directory by this name is created under /proc/asound/
112 containing information about the card
113 - This ID can be used instead of the index number in
116 - Default: enabled, for PCI and ISA PnP cards
121 Module for AdLib FM cards.
123 port - port # for OPL chip
125 This module supports multiple cards. It does not support autoprobe, so
126 the port must be specified. For actual AdLib FM cards it will be 0x388.
127 Note that this card does not have PCM support and no mixer; only FM
130 Make sure you have "sbiload" from the alsa-tools package available and,
131 after loading the module, find out the assigned ALSA sequencer port
132 number through "sbiload -l". Example output:
134 Port Client name Port name
135 64:0 OPL2 FM synth OPL2 FM Port
137 Load the std.sb and drums.sb patches also supplied by sbiload:
139 sbiload -p 64:0 std.sb drums.sb
141 If you use this driver to drive an OPL3, you can use std.o3 and drums.o3
142 instead. To have the card produce sound, use aplaymidi from alsa-utils:
144 aplaymidi -p 64:0 foo.mid
149 Module for sound cards based on Analog Devices AD1816A/AD1815 ISA chips.
151 port - port # for AD1816A chip (PnP setup)
152 mpu_port - port # for MPU-401 UART (PnP setup)
153 fm_port - port # for OPL3 (PnP setup)
154 irq - IRQ # for AD1816A chip (PnP setup)
155 mpu_irq - IRQ # for MPU-401 UART (PnP setup)
156 dma1 - first DMA # for AD1816A chip (PnP setup)
157 dma2 - second DMA # for AD1816A chip (PnP setup)
158 clockfreq - Clock frequency for AD1816A chip (default = 0, 33000Hz)
160 This module supports multiple cards, autoprobe and PnP.
165 Module for sound cards based on AD1848/AD1847/CS4248 ISA chips.
167 port - port # for AD1848 chip
168 irq - IRQ # for AD1848 chip
169 dma1 - DMA # for AD1848 chip (0,1,3)
171 This module supports multiple cards. It does not support autoprobe
172 thus main port must be specified!!! Other ports are optional.
174 The power-management is supported.
179 Module for Analog Devices AD1889 chips.
181 ac97_quirk - AC'97 workaround for strange hardware
182 See the description of intel8x0 module for details.
184 This module supports multiple cards.
189 Module for ALi M5451 PCI chip.
191 pcm_channels - Number of hardware channels assigned for PCM
192 spdif - Support SPDIF I/O
195 This module supports one chip and autoprobe.
197 The power-management is supported.
202 Module for sound cards based on Avance Logic ALS100/ALS120 ISA chips.
204 port - port # for ALS100 (SB16) chip (PnP setup)
205 irq - IRQ # for ALS100 (SB16) chip (PnP setup)
206 dma8 - 8-bit DMA # for ALS100 (SB16) chip (PnP setup)
207 dma16 - 16-bit DMA # for ALS100 (SB16) chip (PnP setup)
208 mpu_port - port # for MPU-401 UART (PnP setup)
209 mpu_irq - IRQ # for MPU-401 (PnP setup)
210 fm_port - port # for OPL3 FM (PnP setup)
212 This module supports multiple cards, autoprobe and PnP.
214 The power-management is supported.
219 Module for Avance Logic ALS300 and ALS300+
221 This module supports multiple cards.
223 The power-management is supported.
228 Module for sound cards based on Avance Logic ALS4000 PCI chip.
230 joystick_port - port # for legacy joystick support.
231 0 = disabled (default), 1 = auto-detect
233 This module supports multiple cards, autoprobe and PnP.
235 The power-management is supported.
240 Module for ATI IXP 150/200/250/400 AC97 controllers.
242 ac97_clock - AC'97 clock (default = 48000)
243 ac97_quirk - AC'97 workaround for strange hardware
244 See "AC97 Quirk Option" section below.
245 ac97_codec - Workaround to specify which AC'97 codec
246 instead of probing. If this works for you
247 file a bug with your `lspci -vn` output.
249 -1 -- Default behavior.
250 0-2 -- Use the specified codec.
251 spdif_aclink - S/PDIF transfer over AC-link (default = 1)
253 This module supports one card and autoprobe.
255 ATI IXP has two different methods to control SPDIF output. One is
256 over AC-link and another is over the "direct" SPDIF output. The
257 implementation depends on the motherboard, and you'll need to
258 choose the correct one via spdif_aclink module option.
260 The power-management is supported.
262 Module snd-atiixp-modem
263 -----------------------
265 Module for ATI IXP 150/200/250 AC97 modem controllers.
267 This module supports one card and autoprobe.
269 Note: The default index value of this module is -2, i.e. the first
272 The power-management is supported.
274 Module snd-au8810, snd-au8820, snd-au8830
275 -----------------------------------------
277 Module for Aureal Vortex, Vortex2 and Advantage device.
279 pcifix - Control PCI workarounds
280 0 = Disable all workarounds
281 1 = Force the PCI latency of the Aureal card to 0xff
282 2 = Force the Extend PCI#2 Internal Master for Efficient
283 Handling of Dummy Requests on the VIA KT133 AGP Bridge
284 3 = Force both settings
285 255 = Autodetect what is required (default)
287 This module supports all ADB PCM channels, ac97 mixer, SPDIF, hardware
288 EQ, mpu401, gameport. A3D and wavetable support are still in development.
289 Development and reverse engineering work is being coordinated at
290 http://savannah.nongnu.org/projects/openvortex/
291 SPDIF output has a copy of the AC97 codec output, unless you use the
292 "spdif" pcm device, which allows raw data passthru.
293 The hardware EQ hardware and SPDIF is only present in the Vortex2 and
296 Note: Some ALSA mixer applications don't handle the SPDIF sample rate
297 control correctly. If you have problems regarding this, try
298 another ALSA compliant mixer (alsamixer works).
303 Module for sound cards based on Aztech System AZT2320 ISA chip (PnP only).
305 port - port # for AZT2320 chip (PnP setup)
306 wss_port - port # for WSS (PnP setup)
307 mpu_port - port # for MPU-401 UART (PnP setup)
308 fm_port - FM port # for AZT2320 chip (PnP setup)
309 irq - IRQ # for AZT2320 (WSS) chip (PnP setup)
310 mpu_irq - IRQ # for MPU-401 UART (PnP setup)
311 dma1 - 1st DMA # for AZT2320 (WSS) chip (PnP setup)
312 dma2 - 2nd DMA # for AZT2320 (WSS) chip (PnP setup)
314 This module supports multiple cards, PnP and autoprobe.
316 The power-management is supported.
321 Module for sound cards based on Aztech AZF3328 PCI chip.
323 joystick - Enable joystick (default off)
325 This module supports multiple cards.
330 Module for video cards based on Bt87x chips.
332 digital_rate - Override the default digital rate (Hz)
333 load_all - Load the driver even if the card model isn't known
335 This module supports multiple cards.
337 Note: The default index value of this module is -2, i.e. the first
343 Module for Creative Audigy LS and SB Live 24bit
345 This module supports multiple cards.
351 Module for sound cards based on C-Media CMI8330 ISA chips.
353 wssport - port # for CMI8330 chip (WSS)
354 wssirq - IRQ # for CMI8330 chip (WSS)
355 wssdma - first DMA # for CMI8330 chip (WSS)
356 sbport - port # for CMI8330 chip (SB16)
357 sbirq - IRQ # for CMI8330 chip (SB16)
358 sbdma8 - 8bit DMA # for CMI8330 chip (SB16)
359 sbdma16 - 16bit DMA # for CMI8330 chip (SB16)
361 This module supports multiple cards and autoprobe.
363 The power-management is supported.
368 Module for C-Media CMI8338/8738/8768/8770 PCI sound cards.
370 mpu_port - port address of MIDI interface:
371 0x300,0x310,0x320,0x330 = legacy port,
372 1 = integrated PCI port (8738 or later),
373 0 = disable (default)
374 fm_port - port address of OPL-3 FM synthesizer (8x38 only):
376 1 = integrated PCI port (default on 8738),
378 soft_ac3 - Software-conversion of raw SPDIF packets (model 033 only)
380 joystick_port - Joystick port address (0 = disable, 1 = auto-detect)
382 This module supports autoprobe and multiple cards.
384 The power-management is supported.
389 Module for sound cards based on CS4231 ISA chips.
391 port - port # for CS4231 chip
392 mpu_port - port # for MPU-401 UART (optional), -1 = disable
393 irq - IRQ # for CS4231 chip
394 mpu_irq - IRQ # for MPU-401 UART
395 dma1 - first DMA # for CS4231 chip
396 dma2 - second DMA # for CS4231 chip
398 This module supports multiple cards. This module does not support autoprobe
399 thus main port must be specified!!! Other ports are optional.
401 The power-management is supported.
406 Module for sound cards based on CS4232/CS4232A ISA chips.
408 port - port # for CS4232 chip (PnP setup - 0x534)
409 cport - control port # for CS4232 chip (PnP setup - 0x120,0x210,0xf00)
410 mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
411 fm_port - FM port # for CS4232 chip (PnP setup - 0x388), -1 = disable
412 irq - IRQ # for CS4232 chip (5,7,9,11,12,15)
413 mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
414 dma1 - first DMA # for CS4232 chip (0,1,3)
415 dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
416 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
418 This module supports multiple cards. This module does not support autoprobe
419 thus main port must be specified!!! Other ports are optional.
421 The power-management is supported.
426 Module for sound cards based on CS4235/CS4236/CS4236B/CS4237B/
427 CS4238B/CS4239 ISA chips.
429 port - port # for CS4236 chip (PnP setup - 0x534)
430 cport - control port # for CS4236 chip (PnP setup - 0x120,0x210,0xf00)
431 mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
432 fm_port - FM port # for CS4236 chip (PnP setup - 0x388), -1 = disable
433 irq - IRQ # for CS4236 chip (5,7,9,11,12,15)
434 mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
435 dma1 - first DMA # for CS4236 chip (0,1,3)
436 dma2 - second DMA # for CS4236 chip (0,1,3), -1 = disable
437 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
439 This module supports multiple cards. This module does not support autoprobe
440 (if ISA PnP is not used) thus main port and control port must be
441 specified!!! Other ports are optional.
443 The power-management is supported.
448 Module for Cirrus Logic CS4281 soundchip.
450 dual_codec - Secondary codec ID (0 = disable, default)
452 This module supports multiple cards.
454 The power-management is supported.
459 Module for PCI sound cards based on CS4610/CS4612/CS4614/CS4615/CS4622/
460 CS4624/CS4630/CS4280 PCI chips.
462 external_amp - Force to enable external amplifier.
463 thinkpad - Force to enable Thinkpad's CLKRUN control.
464 mmap_valid - Support OSS mmap mode (default = 0).
466 This module supports multiple cards and autoprobe.
467 Usually external amp and CLKRUN controls are detected automatically
468 from PCI sub vendor/device ids. If they don't work, give the options
471 The power-management is supported.
476 Module for Cyrix/NatSemi Geode 5530 chip.
478 Module snd-cs5535audio
479 ----------------------
481 Module for multifunction CS5535 companion PCI device
483 The power-management is supported.
488 Module for Echoaudio Darla20
490 This module supports multiple cards.
491 The driver requires the firmware loader support on kernel.
496 Module for Echoaudio Darla24
498 This module supports multiple cards.
499 The driver requires the firmware loader support on kernel.
504 Module for Diamond Technologies DT-019X / Avance Logic ALS-007 (PnP
507 port - Port # (PnP setup)
508 mpu_port - Port # for MPU-401 (PnP setup)
509 fm_port - Port # for FM OPL-3 (PnP setup)
510 irq - IRQ # (PnP setup)
511 mpu_irq - IRQ # for MPU-401 (PnP setup)
512 dma8 - DMA # (PnP setup)
514 This module supports multiple cards. This module is enabled only with
517 The power-management is supported.
522 Module for the dummy sound card. This "card" doesn't do any output
523 or input, but you may use this module for any application which
524 requires a sound card (like RealPlayer).
526 The power-management is supported.
531 Module for Echoaudio 3G cards (Gina3G/Layla3G)
533 This module supports multiple cards.
534 The driver requires the firmware loader support on kernel.
539 Module for EMU10K1/EMU10k2 based PCI sound cards.
540 * Sound Blaster Live!
541 * Sound Blaster PCI 512
542 * Emu APS (partially supported)
543 * Sound Blaster Audigy
545 extin - bitmap of available external inputs for FX8010 (see bellow)
546 extout - bitmap of available external outputs for FX8010 (see bellow)
547 seq_ports - allocated sequencer ports (4 by default)
548 max_synth_voices - limit of voices used for wavetable (64 by default)
549 max_buffer_size - specifies the maximum size of wavetable/pcm buffers
550 given in MB unit. Default value is 128.
551 enable_ir - enable IR
553 This module supports multiple cards and autoprobe.
555 Input & Output configurations [extin/extout]
556 * Creative Card wo/Digital out [0x0003/0x1f03]
557 * Creative Card w/Digital out [0x0003/0x1f0f]
558 * Creative Card w/Digital CD in [0x000f/0x1f0f]
559 * Creative Card wo/Digital out + LiveDrive [0x3fc3/0x1fc3]
560 * Creative Card w/Digital out + LiveDrive [0x3fc3/0x1fcf]
561 * Creative Card w/Digital CD in + LiveDrive [0x3fcf/0x1fcf]
562 * Creative Card wo/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
563 * Creative Card w/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
564 * Creative Card w/Digital CD in + Digital I/O 2 [0x0fcf/0x1f0f]
565 * Creative Card 5.1/w Digital out + LiveDrive [0x3fc3/0x1fff]
566 * Creative Card 5.1 (c) 2003 [0x3fc3/0x7cff]
567 * Creative Card all ins and outs [0x3fff/0x7fff]
569 The power-management is supported.
574 Module for Creative Emu10k1X (SB Live Dell OEM version)
576 This module supports multiple cards.
581 Module for Ensoniq AudioPCI ES1370 PCI sound cards.
582 * SoundBlaster PCI 64
583 * SoundBlaster PCI 128
585 joystick - Enable joystick (default off)
587 This module supports multiple cards and autoprobe.
589 The power-management is supported.
594 Module for Ensoniq AudioPCI ES1371 PCI sound cards.
595 * SoundBlaster PCI 64
596 * SoundBlaster PCI 128
597 * SoundBlaster Vibra PCI
599 joystick_port - port # for joystick (0x200,0x208,0x210,0x218),
600 0 = disable (default), 1 = auto-detect
602 This module supports multiple cards and autoprobe.
604 The power-management is supported.
609 Module for sound cards based on ESS ES968 chip (PnP only).
611 port - port # for ES968 (SB8) chip (PnP setup)
612 irq - IRQ # for ES968 (SB8) chip (PnP setup)
613 dma1 - DMA # for ES968 (SB8) chip (PnP setup)
615 This module supports multiple cards, PnP and autoprobe.
617 The power-management is supported.
622 Module for ESS AudioDrive ES-1688 and ES-688 sound cards.
624 port - port # for ES-1688 chip (0x220,0x240,0x260)
625 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
626 irq - IRQ # for ES-1688 chip (5,7,9,10)
627 mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
628 dma8 - DMA # for ES-1688 chip (0,1,3)
630 This module supports multiple cards and autoprobe (without MPU-401 port).
635 Module for ESS AudioDrive ES-18xx sound cards.
637 port - port # for ES-18xx chip (0x220,0x240,0x260)
638 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
639 fm_port - port # for FM (optional, not used)
640 irq - IRQ # for ES-18xx chip (5,7,9,10)
641 dma1 - first DMA # for ES-18xx chip (0,1,3)
642 dma2 - first DMA # for ES-18xx chip (0,1,3)
643 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
645 This module supports multiple cards, ISA PnP and autoprobe (without MPU-401
646 port if native ISA PnP routines are not used).
647 When dma2 is equal with dma1, the driver works as half-duplex.
649 The power-management is supported.
654 Module for sound cards based on ESS Solo-1 (ES1938,ES1946) chips.
656 This module supports multiple cards and autoprobe.
658 The power-management is supported.
663 Module for sound cards based on ESS Maestro-1/2/2E (ES1968/ES1978) chips.
665 total_bufsize - total buffer size in kB (1-4096kB)
666 pcm_substreams_p - playback channels (1-8, default=2)
667 pcm_substreams_c - capture channels (1-8, default=0)
668 clock - clock (0 = auto-detection)
669 use_pm - support the power-management (0 = off, 1 = on,
671 enable_mpu - enable MPU401 (0 = off, 1 = on, 2 = auto (default))
672 joystick - enable joystick (default off)
674 This module supports multiple cards and autoprobe.
676 The power-management is supported.
681 Module for ForteMedia FM801 based PCI sound cards.
683 tea575x_tuner - Enable TEA575x tuner
684 - 1 = MediaForte 256-PCS
685 - 2 = MediaForte 256-PCPR
686 - 3 = MediaForte 64-PCR
687 - High 16-bits are video (radio) device number + 1
688 - example: 0x10002 (MediaForte 256-PCPR, device 1)
690 This module supports multiple cards and autoprobe.
692 The power-management is supported.
697 Module for Echoaudio Gina20
699 This module supports multiple cards.
700 The driver requires the firmware loader support on kernel.
705 Module for Echoaudio Gina24
707 This module supports multiple cards.
708 The driver requires the firmware loader support on kernel.
710 Module snd-gusclassic
711 ---------------------
713 Module for Gravis UltraSound Classic sound card.
715 port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
716 irq - IRQ # for GF1 chip (3,5,9,11,12,15)
717 dma1 - DMA # for GF1 chip (1,3,5,6,7)
718 dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable)
719 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
720 voices - GF1 voices limit (14-32)
721 pcm_voices - reserved PCM voices
723 This module supports multiple cards and autoprobe.
725 Module snd-gusextreme
726 ---------------------
728 Module for Gravis UltraSound Extreme (Synergy ViperMax) sound card.
730 port - port # for ES-1688 chip (0x220,0x230,0x240,0x250,0x260)
731 gf1_port - port # for GF1 chip (0x210,0x220,0x230,0x240,0x250,0x260,0x270)
732 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable
733 irq - IRQ # for ES-1688 chip (5,7,9,10)
734 gf1_irq - IRQ # for GF1 chip (3,5,9,11,12,15)
735 mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
736 dma8 - DMA # for ES-1688 chip (0,1,3)
737 dma1 - DMA # for GF1 chip (1,3,5,6,7)
738 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
739 voices - GF1 voices limit (14-32)
740 pcm_voices - reserved PCM voices
742 This module supports multiple cards and autoprobe (without MPU-401 port).
747 Module for Gravis UltraSound MAX sound card.
749 port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
750 irq - IRQ # for GF1 chip (3,5,9,11,12,15)
751 dma1 - DMA # for GF1 chip (1,3,5,6,7)
752 dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable)
753 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
754 voices - GF1 voices limit (14-32)
755 pcm_voices - reserved PCM voices
757 This module supports multiple cards and autoprobe.
762 Module for Intel HD Audio (ICH6, ICH6M, ESB2, ICH7, ICH8),
763 ATI SB450, SB600, RS600,
767 model - force the model name
768 position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
769 probe_mask - Bitmask to probe codecs (default = -1, meaning all slots)
770 single_cmd - Use single immediate commands to communicate with
771 codecs (for debugging only)
772 enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
773 power_save - Automatic power-saving timtout (in second, 0 =
774 disable, default = 10)
775 power_save_controller - Reset HD-audio controller in power-saving mode
778 This module supports one card and autoprobe.
780 Each codec may have a model table for different configurations.
781 If your machine isn't listed there, the default (usually minimal)
782 configuration is set up. You can pass "model=<name>" option to
783 specify a certain model in such a case. There are different
784 models depending on the codec chip.
786 Model name Description
787 ---------- -----------
789 3stack 3-jack in back and a headphone out
790 3stack-digout 3-jack in back, a HP out and a SPDIF out
791 5stack 5-jack in back, 2-jack in front
792 5stack-digout 5-jack in back, 2-jack in front, a SPDIF out
793 6stack 6-jack in back, 2-jack in front
794 6stack-digout 6-jack with a SPDIF out
796 z71v 3-jack (HP shared SPDIF)
797 asus 3-jack (ASUS Mobo)
799 asus-dig ASUS with SPDIF out
800 asus-dig2 ASUS with SPDIF out (using GPIO2)
802 fujitsu Fujitsu Laptops (Pi1536)
804 lg LG laptop (m1 express dual)
805 lg-lw LG LW20/LW25 laptop
807 clevo Clevo laptops (m520G, m665n)
808 test for testing/debugging purpose, almost all controls can be
809 adjusted. Appearing only when compiled with
811 auto auto-config reading BIOS (default)
815 hp-3013 HP machines (3013-variant)
816 fujitsu Fujitsu S7020
818 will Will laptops (PB V7900)
819 replacer Replacer 672V
820 basic fixed pin assignment (old default model)
821 auto auto-config reading BIOS (default)
824 fujitsu Fujitsu Laptop
825 hp-bpc HP xw4400/6400/8400/9400 laptops
826 hp-bpc-d7000 HP BPC D7000
829 hippo Hippo (ATI) with jack detection, Sony UX-90s
830 hippo_1 Hippo (Benq) with jack detection
831 sony-assamd Sony ASSAMD
832 basic fixed pin assignment w/o SPDIF
833 auto auto-config reading BIOS (default)
839 auto auto-config reading BIOS (default)
842 3stack-dig 3-stack (2-channel) with SPDIF
843 3stack-6ch 3-stack (6-channel)
844 3stack-6ch-dig 3-stack (6-channel) with SPDIF
845 6stack-dig 6-stack with SPDIF
846 lenovo-101e Lenovo laptop
847 auto auto-config reading BIOS (default)
850 3stack-dig 3-jack with SPDIF I/O
851 6stack-dig 6-jack digital with SPDIF I/O
853 macpro MacPro support
854 mbp3 Macbook Pro rev3
855 imac24 iMac 24'' with jack detection
857 auto auto-config reading BIOS (default)
860 3stack-dig 3-jack with SPDIF I/O
861 6stack-dig 6-jack digital with SPDIF I/O
862 3stack-6ch 3-jack 6-channel
863 3stack-6ch-dig 3-jack 6-channel with SPDIF I/O
864 6stack-dig-demo 6-jack digital for Intel demo board
865 acer Acer laptops (Travelmate 3012WTMi, Aspire 5600, etc)
866 acer-aspire Acer Aspire 9810
867 medion Medion Laptops
868 medion-md2 Medion MD2
870 targa-2ch-dig Targs/MSI with 2-channel
871 laptop-eapd 3-jack with SPDIF I/O and EAPD (Clevo M540JE, M550JE)
872 lenovo-101e Lenovo 101E
873 lenovo-nb0763 Lenovo NB0763
874 lenovo-ms7195-dig Lenovo MS7195
876 6stack-hp HP machines with 6stack (Nettle boards)
877 3stack-hp HP machines with 3stack (Lucknow, Samba boards)
878 auto auto-config reading BIOS (default)
882 3stack-dig 3-jack with SPDIF I/O
883 6stack-dig 6-jack with SPDIF I/O
884 3stack-660 3-jack (for ALC660)
885 uniwill-m31 Uniwill M31 laptop
886 toshiba Toshiba laptop support
887 asus Asus laptop support
888 asus-laptop ASUS F2/F3 laptops
889 auto auto-config reading BIOS (default)
893 3stack-dig 3-jack with SPDIF OUT
894 6stack-dig 6-jack with SPDIF OUT
895 3stack-660 3-jack (for ALC660VD)
896 3stack-660-digout 3-jack with SPDIF OUT (for ALC660VD)
897 lenovo Lenovo 3000 C200
898 dallas Dallas laptops
900 auto auto-config reading BIOS (default)
903 minimal 3-jack in back
904 min_fp 3-jack in back, 2-jack in front
905 full 6-jack in back, 2-jack in front
906 full_dig 6-jack in back, 2-jack in front, SPDIF I/O
907 allout 5-jack in back, 2-jack in front, SPDIF out
908 auto auto-config reading BIOS (default)
911 3stack 3-stack mode (default)
918 basic 3-jack (default)
920 thinkpad Lenovo Thinkpad T60/X60/Z60
927 basic default configuration
928 thinkpad Lenovo Thinkpad T61/X61
931 6stack 6-jack, separate surrounds (default)
932 3stack 3-stack, shared surrounds
933 laptop 2-channel only (FSC V2060, Samsung M50)
934 laptop-eapd 2-channel with EAPD (Samsung R65, ASUS A6J)
935 ultra 2-channel with EAPD (Samsung Ultra tablet PC)
939 6stack-dig ditto with SPDIF
941 3stack-dig ditto with SPDIF
942 laptop 3-jack with hp-jack automute
943 laptop-dig ditto with SPDIF
944 auto auto-config reading BIOS (default)
948 test for testing/debugging purpose, almost all controls
949 can be adjusted. Appearing only when compiled with
953 laptop Basic Laptop config
954 laptop-hp Laptop config for some HP models (subdevice 30A5)
955 laptop-eapd Laptop config with EAPD support
956 test for testing/debugging purpose, almost all controls
957 can be adjusted. Appearing only when compiled with
962 dell-m43 Dell Precision
963 dell-m44 Dell Inspiron
968 5stack D945 5stack + SPDIF
970 intel-mac-v1 Intel Mac Type 1
971 intel-mac-v2 Intel Mac Type 2
972 intel-mac-v3 Intel Mac Type 3
973 intel-mac-v4 Intel Mac Type 4
974 intel-mac-v5 Intel Mac Type 5
975 macmini Intel Mac Mini (equivalent with type 3)
976 macbook Intel Mac Book (eq. type 5)
977 macbook-pro-v1 Intel Mac Book Pro 1st generation (eq. type 3)
978 macbook-pro Intel Mac Book Pro 2nd generation (eq. type 3)
979 imac-intel Intel iMac (eq. type 2)
980 imac-intel-20 Intel iMac (newer version) (eq. type 3)
983 ref Reference board, base config
984 m2-2 Some Gateway MX series laptops
985 m6 Some Gateway NX series laptops
986 pa6 Gateway NX860 series
988 STAC9227/9228/9229/927x
991 5stack D965 5stack + SPDIF
992 dell-3stack Dell E520
995 vaio Setup for VAIO FE550G/SZ110
996 vaio-ar Setup for VAIO AR
998 The model name "genric" is treated as a special case. When this
999 model is given, the driver uses the generic codec parser without
1000 "codec-patch". It's sometimes good for testing and debugging.
1002 If the default configuration doesn't work and one of the above
1003 matches with your device, report it together with the PCI
1004 subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
1005 ML (see the section "Links and Addresses").
1007 When CONFIG_SND_HDA_POWER_SAVE is set, two options, power_save and
1008 power_save_controller become available. power_save specifies the
1009 time to turn off the power automatically at idle status. When
1010 power_save_controller is true, the controller is also turned off.
1011 This might result in more obvious click noise at turning on/off.
1013 Note 2: If you get click noises on output, try the module option
1014 position_fix=1 or 2. position_fix=1 will use the SD_LPIB
1015 register value without FIFO size correction as the current
1016 DMA pointer. position_fix=2 will make the driver to use
1017 the position buffer instead of reading SD_LPIB register.
1018 (Usually SD_LPLIB register is more accurate than the
1021 NB: If you get many "azx_get_response timeout" messages at
1022 loading, it's likely a problem of interrupts (e.g. ACPI irq
1023 routing). Try to boot with options like "pci=noacpi". Also, you
1024 can try "single_cmd=1" module option. This will switch the
1025 communication method between HDA controller and codecs to the
1026 single immediate commands instead of CORB/RIRB. Basically, the
1027 single command mode is provided only for BIOS, and you won't get
1028 unsolicited events, too. But, at least, this works independently
1029 from the irq. Remember this is a last resort, and should be
1030 avoided as much as possible...
1032 MORE NOTES ON "azx_get_response timeout" PROBLEMS:
1033 On some hardwares, you may need to add a proper probe_mask option
1034 to avoid the "azx_get_response timeout" problem above, instead.
1035 This occurs when the access to non-existing or non-working codec slot
1036 (likely a modem one) causes a stall of the communication via HD-audio
1037 bus. You can see which codec slots are probed by enabling
1038 CONFIG_SND_DEBUG_DETECT, or simply from the file name of the codec
1039 proc files. Then limit the slots to probe by probe_mask option.
1040 For example, probe_mask=1 means to probe only the first slot, and
1041 probe_mask=4 means only the third slot.
1043 The power-management is supported.
1048 Module for RME Hammerfall DSP audio interface(s)
1050 This module supports multiple cards.
1052 Note: The firmware data can be automatically loaded via hotplug
1053 when CONFIG_FW_LOADER is set. Otherwise, you need to load
1054 the firmware via hdsploader utility included in alsa-tools
1056 The firmware data is found in alsa-firmware package.
1058 Note: snd-page-alloc module does the job which snd-hammerfall-mem
1059 module did formerly. It will allocate the buffers in advance
1060 when any HDSP cards are found. To make the buffer
1061 allocation sure, load snd-page-alloc module in the early
1062 stage of boot sequence. See "Early Buffer Allocation"
1068 Module for RME HDSP MADI board.
1070 precise_ptr - Enable precise pointer, or disable.
1071 line_outs_monitor - Send playback streams to analog outs by default.
1072 enable_monitor - Enable Analog Out on Channel 63/64 by default.
1074 See hdspm.txt for details.
1079 Module for Envy24 (ICE1712) based PCI sound cards.
1080 * MidiMan M Audio Delta 1010
1081 * MidiMan M Audio Delta 1010LT
1082 * MidiMan M Audio Delta DiO 2496
1083 * MidiMan M Audio Delta 66
1084 * MidiMan M Audio Delta 44
1085 * MidiMan M Audio Delta 410
1086 * MidiMan M Audio Audiophile 2496
1089 * TerraTec EWX 24/96
1090 * TerraTec DMX 6Fire
1092 * Hoontech SoundTrack DSP 24
1093 * Hoontech SoundTrack DSP 24 Value
1094 * Hoontech SoundTrack DSP 24 Media 7.1
1095 * Event Electronics, EZ8
1097 * Lionstracs, Mediastaton
1099 model - Use the given board model, one of the following:
1100 delta1010, dio2496, delta66, delta44, audiophile, delta410,
1101 delta1010lt, vx442, ewx2496, ews88mt, ews88mt_new, ews88d,
1102 dmx6fire, dsp24, dsp24_value, dsp24_71, ez8,
1103 phase88, mediastation
1104 omni - Omni I/O support for MidiMan M-Audio Delta44/66
1105 cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transceiver)
1106 in msec resolution, default value is 500 (0.5 sec)
1108 This module supports multiple cards and autoprobe. Note: The consumer part
1109 is not used with all Envy24 based cards (for example in the MidiMan Delta
1112 Note: The supported board is detected by reading EEPROM or PCI
1113 SSID (if EEPROM isn't available). You can override the
1114 model by passing "model" module option in case that the
1115 driver isn't configured properly or you want to try another
1121 Module for Envy24HT (VT/ICE1724), Envy24PT (VT1720) based PCI sound cards.
1122 * MidiMan M Audio Revolution 5.1
1123 * MidiMan M Audio Revolution 7.1
1124 * MidiMan M Audio Audiophile 192
1126 * TerraTec Aureon 5.1 Sky
1127 * TerraTec Aureon 7.1 Space
1128 * TerraTec Aureon 7.1 Universe
1131 * AudioTrak Prodigy 7.1
1132 * AudioTrak Prodigy 7.1LT
1133 * AudioTrak Prodigy 192
1135 * Albatron K8X800 Pro II
1136 * Chaintech ZNF3-150
1137 * Chaintech ZNF3-250
1142 model - Use the given board model, one of the following:
1143 revo51, revo71, amp2000, prodigy71, prodigy71lt,
1144 prodigy192, aureon51, aureon71, universe, ap192,
1145 k8x800, phase22, phase28, ms300, av710
1147 This module supports multiple cards and autoprobe.
1149 Note: The supported board is detected by reading EEPROM or PCI
1150 SSID (if EEPROM isn't available). You can override the
1151 model by passing "model" module option in case that the
1152 driver isn't configured properly or you want to try another
1158 Module for Echoaudio Indigo
1160 This module supports multiple cards.
1161 The driver requires the firmware loader support on kernel.
1166 Module for Echoaudio Indigo DJ
1168 This module supports multiple cards.
1169 The driver requires the firmware loader support on kernel.
1174 Module for Echoaudio Indigo IO
1176 This module supports multiple cards.
1177 The driver requires the firmware loader support on kernel.
1182 Module for AC'97 motherboards from Intel and compatibles.
1183 * Intel i810/810E, i815, i820, i830, i84x, MX440
1184 ICH5, ICH6, ICH7, ESB2
1185 * SiS 7012 (SiS 735)
1186 * NVidia NForce, NForce2, NForce3, MCP04, CK804
1188 * AMD AMD768, AMD8111
1191 ac97_clock - AC'97 codec clock base (0 = auto-detect)
1192 ac97_quirk - AC'97 workaround for strange hardware
1193 See "AC97 Quirk Option" section below.
1194 buggy_irq - Enable workaround for buggy interrupts on some
1195 motherboards (default yes on nForce chips,
1197 buggy_semaphore - Enable workaround for hardwares with buggy
1198 semaphores (e.g. on some ASUS laptops)
1200 spdif_aclink - Use S/PDIF over AC-link instead of direct connection
1201 from the controller chip
1202 (0 = off, 1 = on, -1 = default)
1204 This module supports one chip and autoprobe.
1206 Note: the latest driver supports auto-detection of chip clock.
1207 if you still encounter too fast playback, specify the clock
1208 explicitly via the module option "ac97_clock=41194".
1210 Joystick/MIDI ports are not supported by this driver. If your
1211 motherboard has these devices, use the ns558 or snd-mpu401
1212 modules, respectively.
1214 The power-management is supported.
1216 Module snd-intel8x0m
1217 --------------------
1219 Module for Intel ICH (i8x0) chipset MC97 modems.
1220 * Intel i810/810E, i815, i820, i830, i84x, MX440
1222 * SiS 7013 (SiS 735)
1223 * NVidia NForce, NForce2, NForce2s, NForce3
1227 ac97_clock - AC'97 codec clock base (0 = auto-detect)
1229 This module supports one card and autoprobe.
1231 Note: The default index value of this module is -2, i.e. the first
1234 The power-management is supported.
1236 Module snd-interwave
1237 --------------------
1239 Module for Gravis UltraSound PnP, Dynasonic 3-D/Pro, STB Sound Rage 32
1240 and other sound cards based on AMD InterWave (tm) chip.
1242 port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
1243 irq - IRQ # for InterWave chip (3,5,9,11,12,15)
1244 dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
1245 dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
1246 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
1247 midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
1248 pcm_voices - reserved PCM voices for the synthesizer (default 2)
1249 effect - 1 = InterWave effects enable (default 0);
1252 This module supports multiple cards, autoprobe and ISA PnP.
1254 Module snd-interwave-stb
1255 ------------------------
1257 Module for UltraSound 32-Pro (sound card from STB used by Compaq)
1258 and other sound cards based on AMD InterWave (tm) chip with TEA6330T
1259 circuit for extended control of bass, treble and master volume.
1261 port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
1262 port_tc - tone control (i2c bus) port # for TEA6330T chip (0x350,0x360,0x370,0x380)
1263 irq - IRQ # for InterWave chip (3,5,9,11,12,15)
1264 dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
1265 dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
1266 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
1267 midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
1268 pcm_voices - reserved PCM voices for the synthesizer (default 2)
1269 effect - 1 = InterWave effects enable (default 0);
1272 This module supports multiple cards, autoprobe and ISA PnP.
1277 Module for Korg 1212 IO PCI card
1279 This module supports multiple cards.
1284 Module for Echoaudio Layla20
1286 This module supports multiple cards.
1287 The driver requires the firmware loader support on kernel.
1292 Module for Echoaudio Layla24
1294 This module supports multiple cards.
1295 The driver requires the firmware loader support on kernel.
1300 Module for Allegro/Maestro3 chips
1302 external_amp - enable external amp (enabled by default)
1303 amp_gpio - GPIO pin number for external amp (0-15) or
1304 -1 for default pin (8 for allegro, 1 for
1307 This module supports autoprobe and multiple chips.
1309 Note: the binding of amplifier is dependent on hardware.
1310 If there is no sound even though all channels are unmuted, try to
1311 specify other gpio connection via amp_gpio option.
1312 For example, a Panasonic notebook might need "amp_gpio=0x0d"
1315 The power-management is supported.
1320 Module for Echoaudio Mia
1322 This module supports multiple cards.
1323 The driver requires the firmware loader support on kernel.
1328 Module for Miro soundcards: miroSOUND PCM 1 pro,
1330 miroSOUND PCM 20 Radio.
1332 port - Port # (0x530,0x604,0xe80,0xf40)
1333 irq - IRQ # (5,7,9,10,11)
1334 dma1 - 1st dma # (0,1,3)
1335 dma2 - 2nd dma # (0,1)
1336 mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330)
1337 mpu_irq - MPU-401 irq # (5,7,9,10)
1338 fm_port - FM Port # (0x388)
1339 wss - enable WSS mode
1340 ide - enable onboard ide support
1345 Module for Digigram miXart8 sound cards.
1347 This module supports multiple cards.
1348 Note: One miXart8 board will be represented as 4 alsa cards.
1349 See MIXART.txt for details.
1351 When the driver is compiled as a module and the hotplug firmware
1352 is supported, the firmware data is loaded via hotplug automatically.
1353 Install the necessary firmware files in alsa-firmware package.
1354 When no hotplug fw loader is available, you need to load the
1355 firmware via mixartloader utility in alsa-tools package.
1360 Module for Echoaudio Mona
1362 This module supports multiple cards.
1363 The driver requires the firmware loader support on kernel.
1368 Module for MPU-401 UART devices.
1370 port - port number or -1 (disable)
1371 irq - IRQ number or -1 (disable)
1372 pnp - PnP detection - 0 = disable, 1 = enable (default)
1373 uart_enter - Issue UART_ENTER command at open - bool, default = on
1375 This module supports multiple devices and PnP.
1380 Module for MOTU MidiTimePiece AV multiport MIDI (on the parallel
1383 port - I/O port # for MTPAV (0x378,0x278, default=0x378)
1384 irq - IRQ # for MTPAV (7,5, default=7)
1385 hwports - number of supported hardware ports, default=8.
1387 Module supports only 1 card. This module has no enable option.
1392 Module for Ego Systems (ESI) Miditerminal 4140
1394 This module supports multiple devices.
1395 Requires parport (CONFIG_PARPORT).
1400 Module for NeoMagic NM256AV/ZX chips
1402 playback_bufsize - max playback frame size in kB (4-128kB)
1403 capture_bufsize - max capture frame size in kB (4-128kB)
1404 force_ac97 - 0 or 1 (disabled by default)
1405 buffer_top - specify buffer top address
1406 use_cache - 0 or 1 (disabled by default)
1407 vaio_hack - alias buffer_top=0x25a800
1408 reset_workaround - enable AC97 RESET workaround for some laptops
1409 reset_workaround2 - enable extended AC97 RESET workaround for some
1412 This module supports one chip and autoprobe.
1414 The power-management is supported.
1416 Note: on some notebooks the buffer address cannot be detected
1417 automatically, or causes hang-up during initialization.
1418 In such a case, specify the buffer top address explicitly via
1419 the buffer_top option.
1421 Sony F250: buffer_top=0x25a800
1422 Sony F270: buffer_top=0x272800
1423 The driver supports only ac97 codec. It's possible to force
1424 to initialize/use ac97 although it's not detected. In such a
1425 case, use force_ac97=1 option - but *NO* guarantee whether it
1428 Note: The NM256 chip can be linked internally with non-AC97
1429 codecs. This driver supports only the AC97 codec, and won't work
1430 with machines with other (most likely CS423x or OPL3SAx) chips,
1431 even though the device is detected in lspci. In such a case, try
1432 other drivers, e.g. snd-cs4232 or snd-opl3sa2. Some has ISA-PnP
1433 but some doesn't have ISA PnP. You'll need to specify isapnp=0
1434 and proper hardware parameters in the case without ISA PnP.
1436 Note: some laptops need a workaround for AC97 RESET. For the
1437 known hardware like Dell Latitude LS and Sony PCG-F305, this
1438 workaround is enabled automatically. For other laptops with a
1439 hard freeze, you can try reset_workaround=1 option.
1441 Note: Dell Latitude CSx laptops have another problem regarding
1442 AC97 RESET. On these laptops, reset_workaround2 option is
1443 turned on as default. This option is worth to try if the
1444 previous reset_workaround option doesn't help.
1446 Note: This driver is really crappy. It's a porting from the
1447 OSS driver, which is a result of black-magic reverse engineering.
1448 The detection of codec will fail if the driver is loaded *after*
1449 X-server as described above. You might be able to force to load
1450 the module, but it may result in hang-up. Hence, make sure that
1451 you load this module *before* X if you encounter this kind of
1457 Module for Yamaha OPL3-SA2/SA3 sound cards.
1459 port - control port # for OPL3-SA chip (0x370)
1460 sb_port - SB port # for OPL3-SA chip (0x220,0x240)
1461 wss_port - WSS port # for OPL3-SA chip (0x530,0xe80,0xf40,0x604)
1462 midi_port - port # for MPU-401 UART (0x300,0x330), -1 = disable
1463 fm_port - FM port # for OPL3-SA chip (0x388), -1 = disable
1464 irq - IRQ # for OPL3-SA chip (5,7,9,10)
1465 dma1 - first DMA # for Yamaha OPL3-SA chip (0,1,3)
1466 dma2 - second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable
1467 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1469 This module supports multiple cards and ISA PnP. It does not support
1470 autoprobe (if ISA PnP is not used) thus all ports must be specified!!!
1472 The power-management is supported.
1474 Module snd-opti92x-ad1848
1475 -------------------------
1477 Module for sound cards based on OPTi 82c92x and Analog Devices AD1848 chips.
1478 Module works with OAK Mozart cards as well.
1480 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1481 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1482 fm_port - port # for OPL3 device (0x388)
1483 irq - IRQ # for WSS chip (5,7,9,10,11)
1484 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1485 dma1 - first DMA # for WSS chip (0,1,3)
1487 This module supports only one card, autoprobe and PnP.
1489 Module snd-opti92x-cs4231
1490 -------------------------
1492 Module for sound cards based on OPTi 82c92x and Crystal CS4231 chips.
1494 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1495 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1496 fm_port - port # for OPL3 device (0x388)
1497 irq - IRQ # for WSS chip (5,7,9,10,11)
1498 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1499 dma1 - first DMA # for WSS chip (0,1,3)
1500 dma2 - second DMA # for WSS chip (0,1,3)
1502 This module supports only one card, autoprobe and PnP.
1507 Module for sound cards based on OPTi 82c93x chips.
1509 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1510 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1511 fm_port - port # for OPL3 device (0x388)
1512 irq - IRQ # for WSS chip (5,7,9,10,11)
1513 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1514 dma1 - first DMA # for WSS chip (0,1,3)
1515 dma2 - second DMA # for WSS chip (0,1,3)
1517 This module supports only one card, autoprobe and PnP.
1522 Module for Digigram PCXHR boards
1524 This module supports multiple cards.
1526 Module snd-portman2x4
1527 ---------------------
1529 Module for Midiman Portman 2x4 parallel port MIDI interface
1531 This module supports multiple cards.
1533 Module snd-powermac (on ppc only)
1534 ---------------------------------
1536 Module for PowerMac, iMac and iBook on-board soundchips
1538 enable_beep - enable beep using PCM (enabled as default)
1540 Module supports autoprobe a chip.
1542 Note: the driver may have problems regarding endianess.
1544 The power-management is supported.
1546 Module snd-pxa2xx-ac97 (on arm only)
1547 ------------------------------------
1549 Module for AC97 driver for the Intel PXA2xx chip
1551 For ARM architecture only.
1553 The power-management is supported.
1558 Module for Conexant Riptide chip
1560 joystick_port - Joystick port # (default: 0x200)
1561 mpu_port - MPU401 port # (default: 0x330)
1562 opl3_port - OPL3 port # (default: 0x388)
1564 This module supports multiple cards.
1565 The driver requires the firmware loader support on kernel.
1566 You need to install the firmware file "riptide.hex" to the standard
1567 firmware path (e.g. /lib/firmware).
1572 Module for RME Digi32, Digi32 Pro and Digi32/8 (Sek'd Prodif32,
1573 Prodif96 and Prodif Gold) sound cards.
1575 This module supports multiple cards.
1580 Module for RME Digi96, Digi96/8 and Digi96/8 PRO/PAD/PST sound cards.
1582 This module supports multiple cards.
1587 Module for RME Digi9652 (Hammerfall, Hammerfall-Light) sound cards.
1589 precise_ptr - Enable precise pointer (doesn't work reliably).
1592 This module supports multiple cards.
1594 Note: snd-page-alloc module does the job which snd-hammerfall-mem
1595 module did formerly. It will allocate the buffers in advance
1596 when any RME9652 cards are found. To make the buffer
1597 allocation sure, load snd-page-alloc module in the early
1598 stage of boot sequence. See "Early Buffer Allocation"
1601 Module snd-sa11xx-uda1341 (on arm only)
1602 ---------------------------------------
1604 Module for Philips UDA1341TS on Compaq iPAQ H3600 sound card.
1606 Module supports only one card.
1607 Module has no enable and index options.
1609 The power-management is supported.
1614 Module for 8-bit SoundBlaster cards: SoundBlaster 1.0,
1618 port - port # for SB DSP chip (0x220,0x240,0x260)
1619 irq - IRQ # for SB DSP chip (5,7,9,10)
1620 dma8 - DMA # for SB DSP chip (1,3)
1622 This module supports multiple cards and autoprobe.
1624 The power-management is supported.
1626 Module snd-sb16 and snd-sbawe
1627 -----------------------------
1629 Module for 16-bit SoundBlaster cards: SoundBlaster 16 (PnP),
1630 SoundBlaster AWE 32 (PnP),
1631 SoundBlaster AWE 64 PnP
1633 port - port # for SB DSP 4.x chip (0x220,0x240,0x260)
1634 mpu_port - port # for MPU-401 UART (0x300,0x330), -1 = disable
1635 awe_port - base port # for EMU8000 synthesizer (0x620,0x640,0x660)
1636 (snd-sbawe module only)
1637 irq - IRQ # for SB DSP 4.x chip (5,7,9,10)
1638 dma8 - 8-bit DMA # for SB DSP 4.x chip (0,1,3)
1639 dma16 - 16-bit DMA # for SB DSP 4.x chip (5,6,7)
1640 mic_agc - Mic Auto-Gain-Control - 0 = disable, 1 = enable (default)
1641 csp - ASP/CSP chip support - 0 = disable (default), 1 = enable
1642 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1644 This module supports multiple cards, autoprobe and ISA PnP.
1646 Note: To use Vibra16X cards in 16-bit half duplex mode, you must
1647 disable 16bit DMA with dma16 = -1 module parameter.
1648 Also, all Sound Blaster 16 type cards can operate in 16-bit
1649 half duplex mode through 8-bit DMA channel by disabling their
1652 The power-management is supported.
1657 Module for Aztech Sound Galaxy sound card.
1659 sbport - Port # for SB16 interface (0x220,0x240)
1660 wssport - Port # for WSS interface (0x530,0xe80,0xf40,0x604)
1661 irq - IRQ # (7,9,10,11)
1664 This module supports multiple cards.
1666 The power-management is supported.
1671 Module for ENSONIQ SoundScape PnP cards.
1673 port - Port # (PnP setup)
1674 irq - IRQ # (PnP setup)
1675 mpu_irq - MPU-401 IRQ # (PnP setup)
1676 dma - DMA # (PnP setup)
1678 This module supports multiple cards. ISA PnP must be enabled.
1679 You need sscape_ctl tool in alsa-tools package for loading
1682 Module snd-sun-amd7930 (on sparc only)
1683 --------------------------------------
1685 Module for AMD7930 sound chips found on Sparcs.
1687 This module supports multiple cards.
1689 Module snd-sun-cs4231 (on sparc only)
1690 -------------------------------------
1692 Module for CS4231 sound chips found on Sparcs.
1694 This module supports multiple cards.
1696 Module snd-sun-dbri (on sparc only)
1697 -----------------------------------
1699 Module for DBRI sound chips found on Sparcs.
1701 This module supports multiple cards.
1703 Module snd-wavefront
1704 --------------------
1706 Module for Turtle Beach Maui, Tropez and Tropez+ sound cards.
1708 cs4232_pcm_port - Port # for CS4232 PCM interface.
1709 cs4232_pcm_irq - IRQ # for CS4232 PCM interface (5,7,9,11,12,15).
1710 cs4232_mpu_port - Port # for CS4232 MPU-401 interface.
1711 cs4232_mpu_irq - IRQ # for CS4232 MPU-401 interface (9,11,12,15).
1712 use_cs4232_midi - Use CS4232 MPU-401 interface
1713 (inaccessibly located inside your computer)
1714 ics2115_port - Port # for ICS2115
1715 ics2115_irq - IRQ # for ICS2115
1716 fm_port - FM OPL-3 Port #
1717 dma1 - DMA1 # for CS4232 PCM interface.
1718 dma2 - DMA2 # for CS4232 PCM interface.
1719 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1721 The below are options for wavefront_synth features:
1722 wf_raw - Assume that we need to boot the OS (default:no)
1723 If yes, then during driver loading, the state of the board is
1724 ignored, and we reset the board and load the firmware anyway.
1725 fx_raw - Assume that the FX process needs help (default:yes)
1726 If false, we'll leave the FX processor in whatever state it is
1727 when the driver is loaded. The default is to download the
1728 microprogram and associated coefficients to set it up for
1729 "default" operation, whatever that means.
1730 debug_default - Debug parameters for card initialization
1731 wait_usecs - How long to wait without sleeping, usecs
1733 This magic number seems to give pretty optimal throughput
1734 based on my limited experimentation.
1735 If you want to play around with it and find a better value, be
1736 my guest. Remember, the idea is to get a number that causes us
1737 to just busy wait for as many WaveFront commands as possible,
1738 without coming up with a number so large that we hog the whole
1740 Specifically, with this number, out of about 134,000 status
1741 waits, only about 250 result in a sleep.
1742 sleep_interval - How long to sleep when waiting for reply
1744 sleep_tries - How many times to try sleeping during a wait
1746 ospath - Pathname to processed ICS2115 OS firmware
1747 (default:wavefront.os)
1748 The path name of the ISC2115 OS firmware. In the recent
1749 version, it's handled via firmware loader framework, so it
1750 must be installed in the proper path, typically,
1752 reset_time - How long to wait for a reset to take effect
1754 ramcheck_time - How many seconds to wait for the RAM test
1756 osrun_time - How many seconds to wait for the ICS2115 OS
1759 This module supports multiple cards and ISA PnP.
1761 Note: the firmware file "wavefront.os" was located in the earlier
1762 version in /etc. Now it's loaded via firmware loader, and
1763 must be in the proper firmware path, such as /lib/firmware.
1764 Copy (or symlink) the file appropriately if you get an error
1765 regarding firmware downloading after upgrading the kernel.
1767 Module snd-sonicvibes
1768 ---------------------
1770 Module for S3 SonicVibes PCI sound cards.
1771 * PINE Schubert 32 PCI
1773 reverb - Reverb Enable - 1 = enable, 0 = disable (default)
1774 - SoundCard must have onboard SRAM for this.
1775 mge - Mic Gain Enable - 1 = enable, 0 = disable (default)
1777 This module supports multiple cards and autoprobe.
1779 Module snd-serial-u16550
1780 ------------------------
1782 Module for UART16550A serial MIDI ports.
1784 port - port # for UART16550A chip
1785 irq - IRQ # for UART16550A chip, -1 = poll mode
1786 speed - speed in bauds (9600,19200,38400,57600,115200)
1788 base - base for divisor in bauds (57600,115200,230400,460800)
1790 outs - number of MIDI ports in a serial port (1-4)
1792 adaptor - Type of adaptor.
1793 0 = Soundcanvas, 1 = MS-124T, 2 = MS-124W S/A,
1794 3 = MS-124W M/B, 4 = Generic
1796 This module supports multiple cards. This module does not support autoprobe
1797 thus the main port must be specified!!! Other options are optional.
1802 Module for Trident 4DWave DX/NX sound cards.
1803 * Best Union Miss Melody 4DWave PCI
1805 * Warpspeed ONSpeed 4DWave PCI
1808 * CHIC True Sound 4Dwave
1809 * Shark Predator4D-PCI
1810 * Jaton SonicWave 4D
1812 pcm_channels - max channels (voices) reserved for PCM
1813 wavetable_size - max wavetable size in kB (4-?kb)
1815 This module supports multiple cards and autoprobe.
1817 The power-management is supported.
1819 Module snd-usb-audio
1820 --------------------
1822 Module for USB audio and USB MIDI devices.
1824 vid - Vendor ID for the device (optional)
1825 pid - Product ID for the device (optional)
1826 device_setup - Device specific magic number (optional)
1827 - Influence depends on the device
1830 This module supports multiple devices, autoprobe and hotplugging.
1832 Module snd-usb-caiaq
1833 --------------------
1835 Module for caiaq UB audio interfaces,
1836 * Native Instruments RigKontrol2
1837 * Native Instruments Kore Controller
1838 * Native Instruments Audio Kontrol 1
1839 * Native Instruments Audio 8 DJ
1841 This module supports multiple devices, autoprobe and hotplugging.
1843 Module snd-usb-usx2y
1844 --------------------
1846 Module for Tascam USB US-122, US-224 and US-428 devices.
1848 This module supports multiple devices, autoprobe and hotplugging.
1850 Note: you need to load the firmware via usx2yloader utility included
1851 in alsa-tools and alsa-firmware packages.
1856 Module for AC'97 motherboards based on VIA 82C686A/686B, 8233,
1857 8233A, 8233C, 8235, 8237 (south) bridge.
1859 mpu_port - 0x300,0x310,0x320,0x330, otherwise obtain BIOS setup
1861 joystick - Enable joystick (default off) [VIA686A/686B only]
1862 ac97_clock - AC'97 codec clock base (default 48000Hz)
1863 dxs_support - support DXS channels,
1864 0 = auto (default), 1 = enable, 2 = disable,
1865 3 = 48k only, 4 = no VRA, 5 = enable any sample
1866 rate and different sample rates on different
1868 [VIA8233/C, 8235, 8237 only]
1869 ac97_quirk - AC'97 workaround for strange hardware
1870 See "AC97 Quirk Option" section below.
1872 This module supports one chip and autoprobe.
1874 Note: on some SMP motherboards like MSI 694D the interrupts might
1875 not be generated properly. In such a case, please try to
1876 set the SMP (or MPS) version on BIOS to 1.1 instead of
1877 default value 1.4. Then the interrupt number will be
1878 assigned under 15. You might also upgrade your BIOS.
1880 Note: VIA8233/5/7 (not VIA8233A) can support DXS (direct sound)
1881 channels as the first PCM. On these channels, up to 4
1882 streams can be played at the same time, and the controller
1883 can perform sample rate conversion with separate rates for
1885 As default (dxs_support = 0), 48k fixed rate is chosen
1886 except for the known devices since the output is often
1887 noisy except for 48k on some mother boards due to the
1889 Please try once dxs_support=5 and if it works on other
1890 sample rates (e.g. 44.1kHz of mp3 playback), please let us
1891 know the PCI subsystem vendor/device id's (output of
1893 If dxs_support=5 does not work, try dxs_support=4; if it
1894 doesn't work too, try dxs_support=1. (dxs_support=1 is
1895 usually for old motherboards. The correct implemented
1896 board should work with 4 or 5.) If it still doesn't
1897 work and the default setting is ok, dxs_support=3 is the
1898 right choice. If the default setting doesn't work at all,
1899 try dxs_support=2 to disable the DXS channels.
1900 In any cases, please let us know the result and the
1901 subsystem vendor/device ids. See "Links and Addresses"
1904 Note: for the MPU401 on VIA823x, use snd-mpu401 driver
1905 additionally. The mpu_port option is for VIA686 chips only.
1907 The power-management is supported.
1909 Module snd-via82xx-modem
1910 ------------------------
1912 Module for VIA82xx AC97 modem
1914 ac97_clock - AC'97 codec clock base (default 48000Hz)
1916 This module supports one card and autoprobe.
1918 Note: The default index value of this module is -2, i.e. the first
1921 The power-management is supported.
1926 Module for virtual rawmidi devices.
1927 This module creates virtual rawmidi devices which communicate
1928 to the corresponding ALSA sequencer ports.
1930 midi_devs - MIDI devices # (1-4, default=4)
1932 This module supports multiple cards.
1937 Module for Digigram VX-Pocket VX222, V222 v2 and Mic cards.
1939 mic - Enable Microphone on V222 Mic (NYI)
1940 ibl - Capture IBL size. (default = 0, minimum size)
1942 This module supports multiple cards.
1944 When the driver is compiled as a module and the hotplug firmware
1945 is supported, the firmware data is loaded via hotplug automatically.
1946 Install the necessary firmware files in alsa-firmware package.
1947 When no hotplug fw loader is available, you need to load the
1948 firmware via vxloader utility in alsa-tools package. To invoke
1949 vxloader automatically, add the following to /etc/modprobe.conf
1951 install snd-vx222 /sbin/modprobe --first-time -i snd-vx222 && /usr/bin/vxloader
1953 (for 2.2/2.4 kernels, add "post-install /usr/bin/vxloader" to
1954 /etc/modules.conf, instead.)
1955 IBL size defines the interrupts period for PCM. The smaller size
1956 gives smaller latency but leads to more CPU consumption, too.
1957 The size is usually aligned to 126. As default (=0), the smallest
1958 size is chosen. The possible IBL values can be found in
1959 /proc/asound/cardX/vx-status proc file.
1961 The power-management is supported.
1966 Module for Digigram VX-Pocket VX2 and 440 PCMCIA cards.
1968 ibl - Capture IBL size. (default = 0, minimum size)
1970 This module supports multiple cards. The module is compiled only when
1971 PCMCIA is supported on kernel.
1973 With the older 2.6.x kernel, to activate the driver via the card
1974 manager, you'll need to set up /etc/pcmcia/vxpocket.conf. See the
1975 sound/pcmcia/vx/vxpocket.c. 2.6.13 or later kernel requires no
1976 longer require a config file.
1978 When the driver is compiled as a module and the hotplug firmware
1979 is supported, the firmware data is loaded via hotplug automatically.
1980 Install the necessary firmware files in alsa-firmware package.
1981 When no hotplug fw loader is available, you need to load the
1982 firmware via vxloader utility in alsa-tools package.
1984 About capture IBL, see the description of snd-vx222 module.
1986 Note: snd-vxp440 driver is merged to snd-vxpocket driver since
1989 The power-management is supported.
1994 Module for Yamaha PCI chips (YMF72x, YMF74x & YMF75x).
1996 mpu_port - 0x300,0x330,0x332,0x334, 0 (disable) by default,
1997 1 (auto-detect for YMF744/754 only)
1998 fm_port - 0x388,0x398,0x3a0,0x3a8, 0 (disable) by default
1999 1 (auto-detect for YMF744/754 only)
2000 joystick_port - 0x201,0x202,0x204,0x205, 0 (disable) by default,
2002 rear_switch - enable shared rear/line-in switch (bool)
2004 This module supports autoprobe and multiple chips.
2006 The power-management is supported.
2008 Module snd-pdaudiocf
2009 --------------------
2011 Module for Sound Core PDAudioCF sound card.
2013 The power-management is supported.
2019 The ac97_quirk option is used to enable/override the workaround for
2020 specific devices on drivers for on-board AC'97 controllers like
2021 snd-intel8x0. Some hardware have swapped output pins between Master
2022 and Headphone, or Surround (thanks to confusion of AC'97
2023 specifications from version to version :-)
2025 The driver provides the auto-detection of known problematic devices,
2026 but some might be unknown or wrongly detected. In such a case, pass
2027 the proper value with this option.
2029 The following strings are accepted:
2030 - default Don't override the default setting
2031 - none Disable the quirk
2032 - hp_only Bind Master and Headphone controls as a single control
2033 - swap_hp Swap headphone and master controls
2034 - swap_surround Swap master and surround controls
2035 - ad_sharing For AD1985, turn on OMS bit and use headphone
2036 - alc_jack For ALC65x, turn on the jack sense mode
2037 - inv_eapd Inverted EAPD implementation
2038 - mute_led Bind EAPD bit for turning on/off mute LED
2040 For backward compatibility, the corresponding integer value -1, 0,
2041 ... are accepted, too.
2043 For example, if "Master" volume control has no effect on your device
2044 but only "Headphone" does, pass ac97_quirk=hp_only module option.
2047 Configuring Non-ISAPNP Cards
2048 ============================
2050 When the kernel is configured with ISA-PnP support, the modules
2051 supporting the isapnp cards will have module options "isapnp".
2052 If this option is set, *only* the ISA-PnP devices will be probed.
2053 For probing the non ISA-PnP cards, you have to pass "isapnp=0" option
2054 together with the proper i/o and irq configuration.
2056 When the kernel is configured without ISA-PnP support, isapnp option
2057 will be not built in.
2060 Module Autoloading Support
2061 ==========================
2063 The ALSA drivers can be loaded automatically on demand by defining
2064 module aliases. The string 'snd-card-%1' is requested for ALSA native
2065 devices where %i is sound card number from zero to seven.
2067 To auto-load an ALSA driver for OSS services, define the string
2068 'sound-slot-%i' where %i means the slot number for OSS, which
2069 corresponds to the card index of ALSA. Usually, define this
2070 as the same card module.
2072 An example configuration for a single emu10k1 card is like below:
2073 ----- /etc/modprobe.conf
2074 alias snd-card-0 snd-emu10k1
2075 alias sound-slot-0 snd-emu10k1
2076 ----- /etc/modprobe.conf
2078 The available number of auto-loaded sound cards depends on the module
2079 option "cards_limit" of snd module. As default it's set to 1.
2080 To enable the auto-loading of multiple cards, specify the number of
2081 sound cards in that option.
2083 When multiple cards are available, it'd better to specify the index
2084 number for each card via module option, too, so that the order of
2085 cards is kept consistent.
2087 An example configuration for two sound cards is like below:
2089 ----- /etc/modprobe.conf
2091 options snd cards_limit=2
2092 alias snd-card-0 snd-interwave
2093 alias snd-card-1 snd-ens1371
2094 options snd-interwave index=0
2095 options snd-ens1371 index=1
2097 alias sound-slot-0 snd-interwave
2098 alias sound-slot-1 snd-ens1371
2099 ----- /etc/modprobe.conf
2101 In this example, the interwave card is always loaded as the first card
2102 (index 0) and ens1371 as the second (index 1).
2105 ALSA PCM devices to OSS devices mapping
2106 =======================================
2108 /dev/snd/pcmC0D0[c|p] -> /dev/audio0 (/dev/audio) -> minor 4
2109 /dev/snd/pcmC0D0[c|p] -> /dev/dsp0 (/dev/dsp) -> minor 3
2110 /dev/snd/pcmC0D1[c|p] -> /dev/adsp0 (/dev/adsp) -> minor 12
2111 /dev/snd/pcmC1D0[c|p] -> /dev/audio1 -> minor 4+16 = 20
2112 /dev/snd/pcmC1D0[c|p] -> /dev/dsp1 -> minor 3+16 = 19
2113 /dev/snd/pcmC1D1[c|p] -> /dev/adsp1 -> minor 12+16 = 28
2114 /dev/snd/pcmC2D0[c|p] -> /dev/audio2 -> minor 4+32 = 36
2115 /dev/snd/pcmC2D0[c|p] -> /dev/dsp2 -> minor 3+32 = 39
2116 /dev/snd/pcmC2D1[c|p] -> /dev/adsp2 -> minor 12+32 = 44
2118 The first number from /dev/snd/pcmC{X}D{Y}[c|p] expression means
2119 sound card number and second means device number. The ALSA devices
2120 have either 'c' or 'p' suffix indicating the direction, capture and
2121 playback, respectively.
2123 Please note that the device mapping above may be varied via the module
2124 options of snd-pcm-oss module.
2127 Proc interfaces (/proc/asound)
2128 ==============================
2130 /proc/asound/card#/pcm#[cp]/oss
2131 -------------------------------
2132 String "erase" - erase all additional informations about OSS applications
2133 String "<app_name> <fragments> <fragment_size> [<options>]"
2135 <app_name> - name of application with (higher priority) or without path
2136 <fragments> - number of fragments or zero if auto
2137 <fragment_size> - size of fragment in bytes or zero if auto
2138 <options> - optional parameters
2139 - disable the application tries to open a pcm device for
2140 this channel but does not want to use it.
2141 (Cause a bug or mmap needs)
2142 It's good for Quake etc...
2143 - direct don't use plugins
2144 - block force block mode (rvplayer)
2145 - non-block force non-block mode
2146 - whole-frag write only whole fragments (optimization affecting
2148 - no-silence do not fill silence ahead to avoid clicks
2149 - buggy-ptr Returns the whitespace blocks in GETOPTR ioctl
2150 instead of filled blocks
2152 Example: echo "x11amp 128 16384" > /proc/asound/card0/pcm0p/oss
2153 echo "squake 0 0 disable" > /proc/asound/card0/pcm0c/oss
2154 echo "rvplayer 0 0 block" > /proc/asound/card0/pcm0p/oss
2157 Early Buffer Allocation
2158 =======================
2160 Some drivers (e.g. hdsp) require the large contiguous buffers, and
2161 sometimes it's too late to find such spaces when the driver module is
2162 actually loaded due to memory fragmentation. You can pre-allocate the
2163 PCM buffers by loading snd-page-alloc module and write commands to its
2164 proc file in prior, for example, in the early boot stage like
2165 /etc/init.d/*.local scripts.
2167 Reading the proc file /proc/drivers/snd-page-alloc shows the current
2168 usage of page allocation. In writing, you can send the following
2169 commands to the snd-page-alloc driver:
2171 - add VENDOR DEVICE MASK SIZE BUFFERS
2173 VENDOR and DEVICE are PCI vendor and device IDs. They take
2174 integer numbers (0x prefix is needed for the hex).
2175 MASK is the PCI DMA mask. Pass 0 if not restricted.
2176 SIZE is the size of each buffer to allocate. You can pass
2177 k and m suffix for KB and MB. The max number is 16MB.
2178 BUFFERS is the number of buffers to allocate. It must be greater
2179 than 0. The max number is 4.
2183 This will erase the all pre-allocated buffers which are not in
2190 ALSA project homepage
2191 http://www.alsa-project.org
2193 ALSA Bug Tracking System
2194 https://bugtrack.alsa-project.org/bugs/
2197 mailto:alsa-devel@alsa-project.org